Search

Materials sliding on a larger substrate age faster than the substrate itself, but no available model of friction takes into account this aspect. We developed a model based on the memory effect of both the mobile and the plane samples, separately, and characterized by macroscopic geometric measurements (e.g., sliding distances and samples sizes). We studied the contact between fresh paper samples and samples that have already underwent several slidings. Experimental and theoretical results are in good agreement. Finally, we used our model to demonstrate how the existing test methods can lead to differences in the measured forces of friction. The results allow both a better understanding and quantitative characterization of the dependence of friction with the history of the contact. [ABSTRACT FROM AUTHOR]

An in-plane elasto-plastic material model and a hygroexpansivity-shrinkage model for paper and board are introduced in this paper. The input parameters for both models are fiber orientation anisotropy and dry solids content. These two models, based on experimental results, could be used in an analytical approach to estimate, for example, plastic strain and shrinkage in simple one-dimensional cases, but for studies of the combined and more complicated effects of hygro-elasto-plastic behavior, a numerical finite element model was constructed. The finite element approach also offered possibilities for studying different structural variations of an orthotropic sheet as well as buckling behavior and internal stress situations under local strain differences. A few examples are presented of the effect of the anisotropy and moisture streaks under stretching and drying conditions on strain differences and buckling. The internal stresses were studied through a case in which the drying of different layers occurred at different stages. Both the anisotropy and moisture streaks were capable of rendering the buckling of the sample visible. The permanency of these defects highly depends on several process stages and tension conditions of the sheet, as demonstrated in this paper. The application possibilities of the hygro-elasto-plastic model are diverse, including investigation into several phenomena and defects appearing in drying, converting and printing process conditions. [ABSTRACT FROM AUTHOR]

Significant dimensional variations may occur in paper-based materials when subjected to changes in moisture content. Moisture induced deformations are governed by the swelling of individual fibres, which is transferred through inter-fibre bonds to the entire fibrous network. Complex interactions between mechanical and hygro-expansive properties take place in the bonding areas, affecting the overall material response. In most network models, the role of these inter-fibre bonds is not explicitly incorporated. This work presents a periodic meso-structural model for the discrete fibrous network, which considers the free-standing fibre segments and inter-fibre bonds. Despite its simplicity, the reference unit-cell enables the incorporation of relevant micro- and meso-structural features such as network structure, fibres and bond geometry and hygro-elastic properties. The proposed model is solved analytically through a proper homogenization strategy, allowing to recover the paper’s anisotropic hygro-mechanical response in terms of effective elastic constants and effective hygro-expansive coefficients, exploiting the coupling at the meso-structural level between hygroscopic and mechanical behavior. A comparison with experimental results obtained from the literature shows that the presented approach is quite accurate in predicting the overall paper response, thereby revealing the influence of several meso-scale parameters (e.g. fibre orientation, dimensions, mechanical strength). [ABSTRACT FROM AUTHOR]

Abstract: Adding slicing to push cutting processes can significantly reduce cutting forces. Creating an appropriate model for the calculation of forces is necessary to completely understand manufacturing processes. In this investigation, a model detailing the cutting forces of stacked thin material using an asymmetrical knife is developed. Equilibrium of forces and frictional effects at the cutting edge are analyzed to determine the components in vertical and horizontal direction of the total cutting force, and their dependency on the slice-push ratio. The friction effects of the new model are based on Coulomb friction. For comparison purposes, an existing shear friction model is extended to discuss the new presented Coulomb friction model. To support the findings, the newly developed model is experimentally verified. [Copyright &y& Elsevier]

Abstract: In this work we present a mathematical model describing the coupled heat and moisture transport in paper. The model is solved numerically and the numerical solution is used to study the interdependency of the moisture and temperature distribution in paper. The results show that variation with temperature of the saturated water vapor concentration and the sorption isotherm parameters are both important for inducing moisture desorption. It is also found that for steep relative humidity ramps moisture sorption generates temperature increments that slow down the sorption process itself. The model is also used to study the moisture gradients in a paper sheet inside a printer from Océ Technologies, which contains a warm print surface. The results predict changes in moisture content of only 0.2%, which suggests that no deformations are induced on the printed sheet. [Copyright &y& Elsevier]

Abstract: The migration of components from paper into Tenax® was studied to determine the influence of molecular size and chemical character of the migrant and the influence of paper characteristics in the migration process. The Weibull model was applied because Fick’s 2nd law of diffusion gave poor fits in some cases. The migration pattern depended on the migrants molecular size and was independent of temperature in the studied range. The migration rate decreased with the migrant molecular size. The influence of the migrants character (polarity and vapour pressure) on the migration behaviour was also studied: nonpolar migrants with high vapour pressure presented low relative migration values and polar migrants presented high values of relative migration. Results indicated that the apparent partition coefficient between paper and the simulant Tenax® increased with the migrant vapour pressure and with both the paper grammage and the recycled pulp content. [ABSTRACT FROM AUTHOR]

Abstract: A new two-dimensional network model is proposed as a micromechanics model to simulate paper’s failure process due to sequentially breakages of fibers and/or bonds. Paper is approximated as a network composed of fibers any two of which link to each other by their intersecting point, namely so-called bond. Fibers distribute along three particular directions, leading to network’s macro-level isotropy. In the framework of finite element method, nodes correspond to fiber-to-fiber bonds, while elements are fiber segments between every two neighboring nodes and described by Timoshenko beam theory. Element breaks when its equivalent internal tensile stress reaches the tensile strength of fiber. Strength of nodes, i.e. fiber-to-fiber bonds is assumed to be dependant on shearing interaction between fibers, considering the dominant interaction is shearing in a plane problem. Numerical examples show the model’s capacity of reflecting basic failure characteristic in paper. Influences of fiber length and the ratio of fiber strength to bond strength are analyzed in detail. [ABSTRACT FROM AUTHOR]

Abstract: In this study, the determinability of time related colour changes in prints made using ink that dries on matte coated paper with the offset printing technique and infrared method, has been investigated with artifical neural networks after analysis of the experimental and numerical methods. In the experimental part a ECI 2002 CMYK test scale is printed on a 135g/m2 matte coated. The prints obtained were measured with a spectrophotometer at certain intervals and by converting the reflection data obtained into the CIELAB colour description spectrum, time related changes in printed colours have been determined. In the empirical study however, colour changes in prints made on matte coated paper using inks that dry with the infrared method are modelled numerically. The average deviation has been found to be 0.4%. As a result, artificial neural networks can be used with the aim to digitally calculate time related colour changes in the offset printing system. [Copyright &y& Elsevier]

Abstract: The influence of the hydrothermal treatment conditions of rice straw (temperature – 150–190°C , time – 0–20min after reaching the operation temperature – and liquid/solid ratio – 6–8), on the composition of liquid and solid fractions was studied. Polynomial models were found for to reproduce the experimental results with errors less than 6%. Operating to 190°C, 15min and 9 liquid/solid ratio was obtained high values of glucose (1.92g/L), xylose (3.97g/L), arabinose (0.99g/L) and acetic acid (1.96g/L), what allows to save capital when not operating with the maximum time and/or liquid/solid ratio; yield in the solid fraction is 88.1% and lignin content 24.43%. If what it is required to obtain good values of yield (96.46%) and lignin content, is necessary to operate to 150°C, obtaining lower concentrations glucose (1.11%), xylose (2.78%), arabinose (0.56%) and acetic acid (0.39%). Ethanolamine pulping of solid fraction of hydrothermal treatment provides pulp with higher or similar properties to those obtained of pulping rice straw with ethanolamine or soda. [Copyright &y& Elsevier]

Abstract: This paper describes hybrid mathematical model which couples the mechanics of the mass/spring model to the acoustic wave propagation model for use in generating the acoustic signal emitted by complex structures of paper fibres under strain. A discussion of the coupling method is presented including remarks on the errors encountered intrinsic to the discretisation scheme. The numerical results of a vibrating rubber band and a vibrating paper fibre are compared to their experimental counterparts. The fundamental frequencies of the acoustic signals are compared showing a close agreement between the experimental and numerical results. [Copyright &y& Elsevier]

In this paper, a finite element procedure is used to study the dynamic behaviour of a paper web in a free span between two rollers, including effects of transport velocity and surrounding air. The paper web is modelled as a three-dimensional orthotropic structure. The influence of air is accounted for by utilizing fluid–solid interaction analyses based on acoustic theory. The contribution of transport velocity is included through gyroscopic matrices and forces. The structural response on harmonic excitations has been studied using linear and non-linear models. Results show that air significantly reduces eigenfrequencies of the web. So called “edge-flutter” is nothing but the result of skew tension profile. Excessive web vibration can be eliminated by adjusting the web tension. [Copyright &y& Elsevier]

A mathematical model describing the heat and mass transfer in the dryer section of a paper machine has been applied to the production data from four paper machines. Model predictions for the machine speed are compared to actual machine speeds for a total of 163 data sets. The mathematical model assumes that the temperature and moisture content remain homogeneous in the thickness direction of the sheet. For three paper machines producing paper with basis weights ranging from 0.056 to 0.159 kg d.s./m2 the model predictions are adequate. For the paper machine producing the heaviest grades with basis weights ranging from 0.189 to 0.390 kg d.s./m2 the model predictions are flawed by a systematic error. For low machine velocities/high basis weights the machine velocity is over-predicted and for high machine velocities/low basis weights the machine velocity is under-predicted. This systematic error is caused by the assumption of homogeneous moisture content and temperature within the sheet being severely in error for thick sheets. [Copyright &y& Elsevier]

The present study investigates two models—two limiting cases—for the internal heat and mass transfer in a multicylinder dryer: the first model assumes that complete redistribution of heat and moisture in the thickness direction occurs instantaneously. The second model assumes that moisture transfer occurs only by vapor diffusion and that heat transfer takes place by conduction and condensation. The two models are written in dimensionless form, and applied for the same set of standard paper machine data. For basis weights below approximately 0.05 kg d.s./m2 the results are so close that the first, simple model is sufficient. A higher limiting basis weight—approximately 0.16 kg d.s./m2—was previously indicated by comparison of model predictions, assuming the simple model, to extensive sets of machine data from four different paper machines. [Copyright &y& Elsevier]