Search

With the number of new satellites increasing dramatically, comprehensive space surveillance is becoming increasingly important. Therefore, high-resolution inverse synthetic aperture radar (ISAR) imaging of satellites can provide an in-situ assessment of the satellites. This paper demonstrates that pseudo-noise signals can also be used for satellite imaging, in addition to classical linear frequency-modulated chirp signals. Pseudo-noise transmission signals offer the advantage of very low cross-correlation values. This, for instance, enables the possibility of a system with multiple channels transmitting instantaneously. Furthermore, it can significantly reduce signal interference with other systems operating in the same frequency spectrum, which is of particular interest for high-bandwidth, high-power systems such as satellite imaging radars. A new routine has been introduced to generate a wideband pseudo-noise signal with a peak-to-average power ratio (PAPR) similar to that of a chirp signal. This is essential for applications where the transmit signal power budget is sharply limited by the high-power amplifier. The paper presents both theoretical descriptions and analysis of the generated pseudo-noise signal as well as the results of an imaging measurement of a real space target using the introduced pseudo-noise signals. [ABSTRACT FROM AUTHOR]

As the variety of space targets expands, two-dimensional (2D) ISAR images prove insufficient for target recognition, necessitating the extraction of three-dimensional (3D) information. The 3D geometry reconstruction method utilizing energy accumulation of ISAR image sequence (ISEA) facilitates superior reconstruction while circumventing the laborious steps associated with factorization methods. Nevertheless, ISEA's neglect of valid information necessitates a high quantity of images and elongated operation times. This paper introduces a partitioned parallel 3D reconstruction method utilizing sorted-energy semi-accumulation with ISAR image sequences (PP-ISEA) to address these limitations. The PP-ISEA innovatively incorporates a two-step search pattern—coarse and fine—that enhances search efficiency and conserves computational resources. It introduces a novel objective function 'sorted-energy semi-accumulation' to discern genuine scatterers from spurious ones and establishes a redundant point exclusion module. Experiments on the scatterer model and simulated electromagnetic model demonstrate that the PP-ISEA reduces the minimum image requirement from ten to four for high-quality scatterer model reconstruction, thereby offering superior reconstruction quality in less time. [ABSTRACT FROM AUTHOR]

Spaceborne synthetic aperture radar (SAR) is an advanced microwave imaging technology that provides all-weather and all-day target information. However, as spaceborne SAR resolution improves, traditional echo signal models based on airborne SAR design become inadequate due to the curved orbit, Earth rotation, and increased propagation distance. In this study, we propose an accurate range model for high-resolution spaceborne SAR by analyzing motion trajectory and Doppler parameters from the perspective of the space geometry of spaceborne SAR. We evaluate the accuracy of existing range models and propose an advanced equivalent squint range model (AESRM) that accurately fits the actual range history and compensates for high-order term errors by introducing third-order and fourth-order error terms while maintaining the simplicity of the traditional model. The proposed AESRM's concise two-dimensional frequency spectrum form facilitates the design of imaging algorithms. Point target simulations confirm the effectiveness of the proposed AESRM, demonstrating significant improvements in fitting accuracy for range histories characterized by nonlinear trajectories. The developed AESRM provides a robust foundation for designing imaging algorithms and enables higher resolution and more accurate radar imaging. [ABSTRACT FROM AUTHOR]

The unknown relative motions between synthetic aperture radar (SAR) and a ground moving target will lead to serious range cell migration (RCM) and Doppler frequency spread (DFS). The energy of the moving target will defocus, given the effect of the RCM and DFS. The moving target will easily produce Doppler ambiguity, due to the low pulse repetition frequency of radar, and the Doppler ambiguity complicates the corrections of the RCM and DFS. In order to address these issues, an efficient ground moving target focusing method for SAR based on scaled Fourier transform and scaled inverse Fourier transform is presented. Firstly, the operations based on the scaled Fourier transform and scaled inverse Fourier transforms are presented to focus the moving targets in consideration of Doppler ambiguity. Subsequently, in accordance with the detailed analysis of multiple target focusing, the spurious peak related to the cross term is removed. The proposed method can accurately eliminate the DFS and RCM, and the well-focused result of the moving target can be achieved under the complex Doppler ambiguity. Then, the blind speed sidelobe can be further avoided. The presented method has high computational efficiency without the step of parameter search. The simulated and measured SAR data are provided to demonstrate the effectiveness of the developed method. [ABSTRACT FROM AUTHOR]

In order to achieve the remote application of inverse synthetic aperture laser radar for high resolution spatial situational awareness, it is essential to analyze the main factors that restrict its remote application. This study combines the range equation of inverse synthetic aperture lidar with the stimulated Brillouin threshold power equation to investigate the variation of laser transmitting power with distance. Additionally, by utilizing the excited Brillouin threshold power equation, laser linewidth formula, and pulse width characteristics of pulse signal, we examine the variation law of laser coherence that meets corresponding power requirements at different distances. The results indicate that a detection distance of 22 km and below can be achieved using continuous fiber lasers without compensation. Coherence compensation is necessary for distances between 22 km and 57 km. For distances ranging from 57 km to 3000 km, pulsed solid-state lasers are used to analyze coherence and conclude that imaging non-cooperative targets within this range is feasible. It is observed that coherence compensation is required from 57 km to 2179 km, becoming more challenging after 2000 km. Furthermore, pulsed solid-state lasers can still be utilized for imaging cooperative targets within a range of 2179–3273 km; however, coherence compensation remains necessary and becomes increasingly difficult. Finally, several coherent length compensation schemes are proposed in order to extend the imaging range of inverse synthetic aperture LiDAR to approximately 3000 km. [ABSTRACT FROM AUTHOR]

Landslides, resulting from disturbances in slope equilibrium, pose a significant threat to landscapes, infrastructure, and human life. Triggered by factors such as intense precipitation, seismic activities, or volcanic eruptions, these events can cause extensive damage and endanger nearby communities. A comprehensive understanding of landslide characteristics, including spatio-temporal patterns, dimensions, and morphology, is vital for effective landslide disaster management. Existing remote sensing approaches mostly use either optical or synthetic aperture radar sensors. Integrating information from both these types of sensors promises greater accuracy for identifying and locating landslides. This study proposes a novel approach, the ML-LaDeCORsat (Machine Learning-based coseismic Landslide Detection using Combined Optical and Radar Satellite Imagery), that integrates freely available Sentinel-1, Palsar-2, and Sentinel-2 imagery data in Google Earth Engine (GEE). The approach also integrates relevant spectral indices and suitable bands used in a machine learning-based classification of coseismic landslides. The approach includes a robust and reproducible training and validation strategy and allows one to choose between five classifiers (CART, Random Forest, GTB, SVM, and Naive Bayes). Using landslides from four different earthquake case studies, we demonstrate the superiority of our approach over existing solutions in coseismic landslide identification and localization, providing a GTB-based detection accuracy of 87–92%. ML-LaDeCORsat can be adapted to other landslide events (GEE script is provided). Transfer learning experiments proved that our model can be applied to other coseismic landslide events without the need for additional training data. Our novel approach therefore facilitates quick and reliable identification of coseismic landslides, highlighting its potential to contribute towards more effective disaster management. [ABSTRACT FROM AUTHOR]

Multistatic synthetic aperture radar (SAR) is a special mode of SAR system. The radar transmitter and receiver are located on different satellites, which brings many advantages, such as flexible baseline configuration, diverse receiving modes, and more detailed ground object classification information. The multistatic SAR has been widely used in interferometry, moving target detection, three-dimensional imaging, and other fields. The frequency offset between different oscillators will cause a modulation phase error in the signal. Therefore, phase synchronization is one of the most critical problems to be addressed in distributed SAR systems. This article reviews phase synchronization techniques, which are mainly divided into two methods: synchronization by direct microwave link and synchronization by a data-based estimation algorithm. Furthermore, the future development of synchronization technology is anticipated. [ABSTRACT FROM AUTHOR]

Deformation along a subway rail network is related to the safe operation of the subway and the stability of construction facilities on the surface, making long-term deformation monitoring imperative. Long-term monitoring of surface deformation along the subway network and statistical analysis of the overall deformation situation are lacking in China. Therefore, targeting 35 Chinese cities whose subway mileage exceeds 50 km, we extracted their surface deformation along subway networks between 2018 and 2022, using spaceborne synthetic aperture radar (SAR) interferometry (InSAR) technology and Sentinel-1 satellite data. We verified the results with the continuous global navigation satellite system (GNSS) stations' data and found that the root mean square error (RMSE) of the InSAR results was 3.75 mm/year. Statistical analysis showed that ground subsidence along the subways was more prominent in Beijing, Tianjin, and other areas in the North China Plain, namely Kunming (which is dominated by karst landforms), as well as Shanghai, Guangzhou, Qingdao, and other coastal cities. In addition, an analysis revealed that the severity of surface subsidence correlated positively with a city's gross domestic product (GDP) with a Pearson correlation of 0.787, since the higher the GDP, the more frequent the construction and maintenance of subway, and the more commuters there are, which in turn exacerbates the disturbance to the surface. Additionally, the type of land cover also affects the ground deformation. Our findings provide a reference for constructing, operating, and maintaining the urban subway systems in China. [ABSTRACT FROM AUTHOR]

In recent years, jamming strategies for Synthetic Aperture Radar (SAR) pertaining to target detection and identification, such as the creation of false targets, electromagnetic (EM) deception, and signal spoofing, have been increasingly emphasized. Distinct from traditional SAR jamming approaches, the introduction of an innovative artificial material cloak in SAR target jamming presents augmented capabilities. These methods demonstrate a proficient redirection of incident EM waves in specific or arbitrary directions, effectively masking the vital information linked to critical targets. This study introduces a broadband SAR target jamming system employing an information metasurface that incorporates intelligent information processing algorithms in conjunction with a space-time-coding digital metasurface, endowing it with the capacity to adeptly modulate incident EM waves. This integration facilitates a versatile approach to jamming, enabling the deployment of multi-mode protective measures against critical targets. The conducted simulation and experiment results validate the system's ability to adjustably produce EM deception and generate multiple false targets independently of the SAR system. The outcomes of this research significantly advance the practicality of SAR protection strategies, pushing the boundaries toward more dynamic, broadband, and controllable scenarios, thereby substantially improving the concealment of critical targets in highly sensitive conflict areas. [ABSTRACT FROM AUTHOR]

With the rapidly growing interest in using structural timber, a need exists to inspect and assess these structures using non-destructive testing (NDT). This review article summarizes NDT methods for wood inspection. After an overview of the most important NDT methods currently used, a detailed review of Ground Penetrating Radar (GPR) and Ultrasonic Testing (UST) is presented. These two techniques can be applied in situ and produce useful visual representations for quantitative assessments and damage detection. With its commercial availability and portability, GPR can help rapidly identify critical features such as moisture, voids, and metal connectors in wood structures. UST, which effectively detects deep cracks, delaminations, and variations in ultrasonic wave velocity related to moisture content, complements GPR's capabilities. The non-destructive nature of both techniques preserves the structural integrity of timber, enabling thorough assessments without compromising integrity and durability. Techniques such as the Synthetic Aperture Focusing Technique (SAFT) and Total Focusing Method (TFM) allow for reconstructing images that an inspector can readily interpret for quantitative assessment. The development of new sensors, instruments, and analysis techniques has continued to improve the application of GPR and UST on wood. However, due to the hon-homogeneous anisotropic properties of this complex material, challenges remain to quantify defects and characterize inclusions reliably and accurately. By integrating advanced imaging algorithms that consider the material's complex properties, combining measurements with simulations, and employing machine learning techniques, the implementation and application of GPR and UST imaging and damage detection for wood structures can be further advanced. [ABSTRACT FROM AUTHOR]

High-resolution and wide-swath (HRWS) synthetic aperture radar (SAR) imaging with azimuth multi-channel always suffers from channel phase and amplitude errors. Compared with spatial-invariant error, the range-dependent channel phase error is intractable due to its spatial dependency characteristic. This paper proposes a novel parameterized channel equalization approach to reconstruct the unambiguous SAR imagery. First, a linear model is established for the range-dependent channel phase error, and the sharpness of the reconstructed Doppler spectrum is used to measure the unambiguity quality. Furthermore, the intrinsic relationship between the channel phase errors and the sharpness is revealed, which allows us to estimate the optimal parameters by maximizing the sharpness of the reconstructed Doppler spectrum. Finally, the results from real-measured data show that the suggested method performs exceptionally for ambiguity suppression in HRWS SAR imaging. [ABSTRACT FROM AUTHOR]

In synthetic aperture radar (SAR) signal processing, compared with the raw data of level-0, level-1 SAR images are more readily accessible and available in larger quantities. However, an amount of level-1 images are affected by radio frequency interference (RFI), which typically originates from Linear Frequency Modulation (LFM) signals emitted by ground-based radars. Existing research on interference suppression in level-1 data has primarily focused on two methods: transforming SAR images into simulated echo data for interference suppression, or focusing interference in the frequency domain and applying notching filters to reduce interference energy. However, these methods overlook the effective utilization of the interference parameters or are confined to suppressing only one type of LFM interference at a time. In certain SAR images, multiple types of LFM interference manifest bright radiation artifacts that exhibit varying lengths along the range direction while remaining constant in the azimuth direction. It is necessary to suppress multiple LFM interference on SAR images when original echo data are unavailable. This article proposes a joint sparse recovery algorithm for interference suppression in the SAR image domain. In the SAR image domain, two-dimensional LFM interference typically exhibits differences in parameters such as frequency modulation rate and pulse width in the range direction, while maintaining consistency in the azimuth direction. Based on this observation, this article constructs a series of focusing operators for LFM interference in SAR images. These operators enable the sparse representation of dispersed LFM interference. Subsequently, an optimization model is developed that can effectively suppress multi-LFM interference and reduce image loss with the assistance of a regularization term in the image domain. Simulation experiments conducted in various scenarios validate the superior performance of the proposed method. [ABSTRACT FROM AUTHOR]

The imaging of high-speed high-squint synthetic aperture radar (HSHS-SAR), which is mounted on maneuvering platforms with curved trajectory, is a challenging task due to the existence of 3-D acceleration and the azimuth spatial variability of range migration and Doppler parameters. Although existing imaging algorithms based on linear range walk correction (LRWC) and nonlinear chirp scaling (NCS) can reduce the range–azimuth coupling of the frequency spectrum (FS) and the spatial variability of the Doppler parameter to some extent, they become invalid as the squint angle, speed, and resolution increase. Additionally, most of them ignore the effect of acceleration phase calibration (APC) on NCS, which should not be neglected as resolution increases. For these issues, a modified frequency nonlinear chirp scaling (MFNCS) algorithm is proposed in this paper. The proposed MFNCS algorithm mainly includes the following aspects. First, a more accurate approximation of range model (MAARM) is established to improve the accuracy of the instantaneous slant range history. Second, a preprocessing of the proposed algorithm based on the first range compression, LRWC, and a spatial-invariant APC (SIVAPC) is implemented to eliminate most of the effects of high-squint angle and 3-D acceleration on the FS. Third, a spatial-variant APC (SVAPC) is performed to remove azimuth spatial variability introduced by 3-D acceleration, and the range focusing is accomplished by the bulk range cell migration correction (BRCMC) and extended secondary range compression (ESRC). Fourth, the azimuth-dependent characteristics evaluation based on LRWC, SIVAPC, and SVAPC is completed to derive the MFNCS algorithm with fifth-order chirp scaling function for azimuth compression. Consequently, the final image is focused on the range time and azimuth frequency domain. The experimental simulation results verify the effectiveness of the proposed algorithm. With a curved trajectory, HSHS-SAR imaging is carried out at a 50° geometric squint angle and 500 m × 500 m imaging width. The integrated sidelobe ratio and peak sidelobe ratio of the point targets at the scenario edges approach the theoretical values, and the range-azimuth resolution is 1.5 m × 3.0 m. [ABSTRACT FROM AUTHOR]

Circular synthetic aperture radar (CSAR) possesses the capability of multi-angle observation, breaking through the geometric observation constraints of traditional strip SAR and holding the potential for three-dimensional imaging. Its sub-wavelength level of planar resolution, resulting from a long synthetic aperture, makes CSAR highly valuable in the field of high-precision mapping. However, the motion geometry of CSAR is more intricate compared to traditional strip SAR, demanding high precision from navigation systems. The accumulation of errors over the long synthetic aperture time cannot be overlooked. CSAR exhibits significant coupling between the range and azimuth directions, making traditional motion compensation methods based on linear SAR unsuitable for direct application in CSAR. The dynamic nature of flight, with its continuous changes in attitude, introduces a significant deformation error between the non-rigidly connected Inertial Measurement Unit (IMU) and the Global Positioning System (GPS). This deformation error makes it difficult to accurately obtain radar position information, resulting in imaging defocus. The research in this article uncovers a correlation between the deformation error and radial acceleration. Leveraging this insight, we propose utilizing radial acceleration to estimate residual motion errors. This paper delves into the analysis of Position and Orientation System (POS) errors, presenting a novel high-resolution CSAR motion compensation method based on airborne platform acceleration information. Once the system deformation parameters are calibrated using point targets, the deformation error can be directly calculated and compensated based on the acceleration information, ultimately resulting in the generation of a high-resolution image. In this paper, the effectiveness of the method is verified with airborne flight test data. This method can compensate for the deformation error and effectively improve the peak sidelobe ratio and integral sidelobe ratio of the target, thus improving image quality. The introduction of acceleration information provides new means and methods for high-resolution CSAR imaging. [ABSTRACT FROM AUTHOR]

Synthetic aperture radar (SAR) change detection provides a powerful tool for continuous, reliable, and objective observation of the Earth, supporting a wide range of applications that require regular monitoring and assessment of changes in the natural and built environment. In this paper, we introduce a novel SAR image change detection method based on principal component analysis and two-level clustering. First, two difference images of the log-ratio and mean-ratio operators are computed, then the principal component analysis fusion model is used to fuse the two difference images, and a new difference image is generated. To incorporate contextual information during the feature extraction phase, Gabor wavelets are used to obtain the representation of the difference image across multiple scales and orientations. The maximum magnitude across all orientations at each scale is then concatenated to form the Gabor feature vector. Following this, a cascading clustering algorithm is developed within this discriminative feature space by merging the first-level fuzzy c-means clustering with the second-level neighbor rule. Ultimately, the two-level combination of the changed and unchanged results produces the final change map. Five SAR datasets are used for the experiment, and the results show that our algorithm has significant advantages in SAR change detection. [ABSTRACT FROM AUTHOR]

Characterizing the coseismic slip behaviors of earthquakes could offer a better understanding of regional crustal deformation and future seismic potential assessments. On 18 December 2023, an Mw 6.0 earthquake occurred on the Lajishan–Jishishan fault system (LJFS) in the northeastern Tibetan Plateau, causing serious damage and casualties. The seismogenic fault hosting this earthquake is not well constrained, as no surface rupture was identified in the field. To address this issue, in this study, we use Interferometric Synthetic Aperture Radar (InSAR) data to investigate the coseismic surface deformation of this earthquake and invert both ascending and descending line-of-sight observations to probe the seismogenic fault and its slip characteristics. The InSAR observations show up to ~6 cm surface uplift caused by the Jishishan earthquake, which is consistent with the thrust-dominated focal mechanism. A Bayesian-based dislocation modeling indicates that two fault models, with eastern and western dip orientations, could reasonably fit the InSAR observations. By calculating the coseismic Coulomb failure stress changes (∆CFS) induced by both fault models, we find that the east-dipping fault scenario could reasonably explain the aftershock distributions under the framework of stress triggering, while the west-dipping fault scenario produced a negative ∆CFS in the region of dense aftershocks. Integrating regional geological structures, we suggest that the seismogenic fault of the Jishishan earthquake, which strikes NNE with a dip of 56° to the east, may be either the Jishishan western margin fault or a secondary buried branch. The optimal finite-fault slip modeling shows that the coseismic slip was dominated by reverse slip and confined to a depth range between ~5 and 15 km. The released seismic moment is 1.61 × 1018 N·m, which is equivalent to an Mw 6.07 earthquake. While the Jishishan earthquake ruptured a fault segment of approximately 20 km, it only released a small part of the seismic moment that was accumulated along the 220 km long Lajishan–Jishishan fault system. The remaining segments of the Lajishan–Jishishan fault system still have the capability to generate moderate-to-large earthquakes in the future. [ABSTRACT FROM AUTHOR]

Tomographic Synthetic Aperture Radar (TomoSAR) building object height inversion is a sparse reconstruction problem that utilizes the data obtained from several spacecraft passes to invert the scatterer position in the height direction. In practical applications, the number of passes is often small, and the observation data are also small due to the objective conditions, so this study focuses on the inversion under the restricted observation data conditions. The Analytic Learned Iterative Shrinkage Thresholding Algorithm (ALISTA) is a kind of deep unfolding network algorithm, which is a combination of the Iterative Shrinkage Thresholding Algorithm (ISTA) and deep learning technology, and it has the advantages of both. The ALISTA is one of the representative algorithms for TomoSAR building object height inversion. However, the structure of the ALISTA algorithm is simple, which has neither the excellent connection structure of a deep learning network nor the acceleration format combined with the ISTA algorithm. Therefore, this study proposes two directions of improvement for the ALISTA algorithm: firstly, an improvement in the inter-layer connection of the network by introducing a connection similar to residual networks obtains the Extragradient Analytic Learned Iterative Shrinkage Thresholding Algorithm (EALISTA) and further proves that the EALISTA achieves linear convergence; secondly, there is an improvement in the iterative format of the intra-layer iteration of the network by introducing the Nesterov momentum acceleration, which obtains the Fast Analytic Learned Iterative Shrinkage Thresholding Algorithm (FALISTA). We first performed inversion experiments on simulated data, which verified the effectiveness of the two proposed algorithms. Then, we conducted TomoSAR building object height inversion experiments on limited measured data and used the deviation metric P to measure the robustness of the algorithms to invert under restricted observation data. The results show that both proposed algorithms have better robustness, which verifies the superior performance of the two algorithms. In addition, we further analyze how to choose the most suitable algorithms for inversion in engineering practice applications based on the results of the experiments on measured data. [ABSTRACT FROM AUTHOR]

As the demand for precise navigation of aircraft increases in modern society, researching high-precision, high-autonomy navigation systems is both theoretically valuable and practically significant. Because the inertial navigation system (INS) has systematic and random errors, its output information diverges. Therefore, it is necessary to combine them with other navigation systems for real-time compensation and correction of these errors. The SAR matching positioning and navigation system uses synthetic aperture radar (SAR) image matching for platform positioning and compensates for the drift caused by errors in the inertial measurement unit (IMU). Images obtained by SAR are matched with digital landmark data, and the platform's position is calculated based on the SAR imaging geometry. However, SAR matching positioning faces challenges due to seasonal variations in SAR images, the need for typical landmarks for matching, and the lack of elevation information in two-dimensional SAR image matching. This paper proposes an airborne platform positioning method based on interferometric SAR (InSAR) interferogram matching. InSAR interferograms contain terrain elevation information, are less affected by seasonal changes, and provide higher positioning accuracy and robustness. By matching real-time InSAR-processed interferograms with simulated interferograms using a digital elevation model (DEM), three-dimensional position information about the matching points has been obtained. Subsequently, a three-dimensional positioning model for the platform has bene established using the unit line-of-sight vector decomposition method. In actual flight experiments using an FMCW Ku-band Interferometric SAR system, the proposed platform positioning framework demonstrated its ability to achieve precise positioning in the absence of signals from the global navigation satellite system (GNSS). [ABSTRACT FROM AUTHOR]

Compared to conventional radars, arc array synthetic aperture radar (SAR) enables wide-area observation under ideal conditions. However, helicopters carrying arc array SAR platforms are generally smaller in size and more sensitive to vibration, which has a greater impact on the imaging quality. In this paper, the vibration error of the arc array SAR platform is investigated, and a vibration error model of the arc array SAR platform is established. Based on the study of the vibration error model, a vibration phase estimation and compensation algorithm based on the delayed conjugate multiplication method is proposed. In the first step, distance pulse pressure processing is performed on the echo signal. In the second step, the pulse pressure signals and their delays in the same distance unit are subjected to conjugate multiplication, and the phase of the signal after conjugate multiplication is extracted. The extracted phase is then amplitude- and phase-compensated to estimate the vibration phase. In the third step, the vibration phase is compensated in the azimuthal direction of the distance pulse pressure signal, and the pairwise echo is eliminated, which completes the compensation of the airborne arc array SAR vibration platform. [ABSTRACT FROM AUTHOR]

A novel image-reconstruction method is proposed for the processing of data acquired at random spatial positions. The images are reconstructed and updated in real time concurrently with the measurements to produce an evolving image, the quality of which is continuously improving and converging as the number of data points increases with the stream of additional measurements. It is shown that the images converge to those obtained with data acquired on a uniformly sampled surface, where the sampling density satisfies the Nyquist limit. The image reconstruction employs a new formulation of the method of scattered power mapping (SPM), which first maps the data into a three-dimensional (3D) preliminary image of the target on a uniform spatial grid, followed by fast Fourier space image deconvolution that provides the high-quality 3D image. [ABSTRACT FROM AUTHOR]

The significant differences in data domains between SAR images and the expensive and time-consuming process of data labeling pose significant challenges to terrain classification. Current terrain classification methodologies face challenges in addressing domain disparities and detecting uncommon terrain effectively. Based on Style Transformation and Domain Metrics (STDMs), we propose an unsupervised domain adaptive framework named STDM-UDA for terrain classification in this paper, which consists of two steps: image style transfer and domain adaptive segmentation. As a first step, image style transfer is performed within the image space to mitigate the differences in low-level features between SAR image domains. Subsequently, leveraging this process, the segmentation network extracts image features, employing domain metrics and adversarial training to enhance alignment between domain gaps in the semantic feature space. Finally, experiments conducted on several pairs of SAR images, each exhibiting varying degrees of differences in key imaging parameters such as source, resolution, band, and polarization, demonstrate the robustness of the proposed method. It achieves remarkably competitive classification accuracy, particularly for unlabeled, high-resolution broad scenes, effectively overcoming the domain gaps introduced by the diverse imaging parameters under studies. [ABSTRACT FROM AUTHOR]

SAR imagery plays a crucial role in geological and environmental monitoring, particularly in highland mountainous regions. However, inherent geometric distortions in SAR images often undermine the precision of remote sensing analyses. Accurately identifying and classifying these distortions is key to analyzing their origins and enhancing the quality and accuracy of monitoring efforts. While the layover and shadow map (LSM) approach is commonly utilized to identify distortions, it falls short in classifying subtle ones. This study introduces a novel LSM ground-range slope (LG) method, tailored for the refined identification of minor distortions to augment the LSM approach. We implemented the LG method on Sentinel-1 SAR imagery from the tri-junction area where the Xiaojiang, Pudu, and Jinsha rivers converge at the Yunnan-Sichuan border. By comparing effective monitoring-point densities, we evaluated and validated traditional methods—LSM, R-Index, and P-NG—against the LG method. The LG method demonstrates superior performance in discriminating subtle distortions within complex terrains through its secondary classification process, which allows for precise and comprehensive recognition of geometric distortions. Furthermore, our research examines the impact of varying slope parameters during the classification process on the accuracy of distortion identification. This study addresses significant gaps in recognizing geometric distortions and lays a foundation for more precise SAR imagery analysis in complex geographic settings. [ABSTRACT FROM AUTHOR]

Groundwater resources are crucial to socio-economic development and the ecosystem, and over-extraction can cause the groundwater level to drop, deplete reserves, and trigger geological hazards like land subsidence. The North China Plain (NCP) has experienced both subsidence and groundwater depletion due to over-extraction in the past 70 years. In this study, we used MT-InSAR technology and ascending C-band Sentinel-1 SAR data from 2017 to 2023 to study land deformation in the junction area of Shijiazhuang–Baoding–Cangzhou–Hengshui. We identified multiple subsidence funnels with a maximum rate exceeding −150 mm/year and a total deformation surpassing 600 mm. Seasonal decomposition methods accurately separated seasonal signals in the time-series deformation and groundwater level data. An exponential function model applied to long-term deformation showed no significant decrease in subsidence in severely affected areas. By modeling seasonal deformation and seasonal groundwater levels, we determined the elastic skeletal storage coefficients (Ske) to be in the range of 1.02 × 10−3~6.53 × 10−3 in subsidence areas. We obtained the spatiotemporal evolution of the total groundwater storage (TGWS), irreversible ground storage (IGWS), and recoverable ground storage (RGWS). The TGWS and IGWS decreased annually while the RGWS increased, which is attributable to the implementation of the South-to-North Water Diversion Project (SNWDP) and the issuance of groundwater withdrawal policies in the NCP. [ABSTRACT FROM AUTHOR]

Tidal flats are some of the most dynamic coastal environments in the world, where traditional coastal mapping and monitoring provide insufficient temporal resolution to reliably map channels and sand flats. Satellite-based Synthetic Aperture Radar (SAR) enables regular cloud-penetrating detection of water flowing through channels within the tidal flats, referred to as tidal channels. This paper presents a method for detecting a path through tidal channels, using satellite imagery, that supports our understanding and safe exploitation of this valuable coastal environment. This approach is the first proposed to identify navigable paths in all conditions, with SAR images susceptible to variation due to weather and tidal conditions. Tidal channels are known to vary in SAR presentation, and we find that tidal flat presentation is also influenced by conditions. The most influential factor is the wind, with high winds causing an inversion in how both tidal flats and tidal channels present in SAR images. The presented method for the automatic detection of tidal channels accounts for this variability by using previous channel paths as a reference to reliably correct imagery and detect the latest path. The final algorithm produces paths with minor errors in 17.6% of images; the error rate increases to 71.7%, with an almost tenfold increase in errors, when the SAR image and paths are not adjusted to account for conditions. This capability has been used to support the Nith Inshore Rescue in attending call-outs from their base in Glencaple, UK, while the insights from monitoring tidal channels for a year demonstrate how periods of high river flow preceded major changes in the channel path. [ABSTRACT FROM AUTHOR]

A novel compressive sensing (CS) synthetic-aperture radar (SAR) called AgileSAR has been proposed to increase swath width for sparse scenes while preserving azimuthal resolution. AgileSAR overcomes the limitation of the Nyquist sampling theorem so that it has a small amount of data and low system complexity. However, traditional CS optimization-based algorithms suffer from manual tuning and pre-definition of optimization parameters, and they generally involve high time and computational complexity for AgileSAR imaging. To address these issues, a pseudo- L 0 -norm fast iterative shrinkage algorithm network (pseudo- L 0 -norm FISTA-net) is proposed for AgileSAR imaging via the deep unfolding network in this paper. Firstly, a pseudo- L 0 -norm regularization model is built by taking an approximately fair penalization rule based on Bayesian estimation. Then, we unfold the operation process of FISTA into a data-driven deep network to solve the pseudo- L 0 -norm regularization model. The network's parameters are automatically learned, and the learned network significantly increases imaging speed, so that it can improve the accuracy and efficiency of AgileSAR imaging. In addition, the nonlinearly sparsifying transform can learn more target details than the traditional sparsifying transform. Finally, the simulated and data experiments demonstrate the superiority and efficiency of the pseudo- L 0 -norm FISTA-net for AgileSAR imaging. [ABSTRACT FROM AUTHOR]

Interferometric synthetic aperture radar (InSAR) and tomographic SAR measurement techniques are commonly used for the three-dimensional (3D) reconstruction of complex areas, while the effectiveness of these methods relies on the interferometric coherence among SAR images with minimal angular disparities. Radargrammetry exploits stereo image matching to determine the spatial coordinates of corresponding points in two SAR images and acquire their 3D properties. The performance of the image matching process directly impacts the quality of the resulting digital surface model (DSM). However, the presence of speckle noise, along with dissimilar geometric and radiometric distortions, poses considerable challenges in achieving accurate stereo SAR image matching. To address these aforementioned challenges, this paper proposes a radargrammetric method based on the composite registration of multi-aspect SAR images. The proposed method combines coarse registration using scale invariant feature transform (SIFT) with precise registration using normalized cross-correlation (NCC) to achieve accurate registration between multi-aspect SAR images with large disparities. Furthermore, the multi-aspect 3D point clouds are merged using the proposed radargrammetric 3D imaging method, resulting in the 3D imaging of target scenes based on multi-aspect SAR images. For validation purposes, this paper presents a comprehensive 3D reconstruction of the Five-hundred-meter Aperture Spherical radio Telescope (FAST) using Ka-band airborne SAR images. It does not necessitate prior knowledge of the target and is applicable to the detailed 3D imaging of large-scale areas with complex structures. In comparison to other SAR 3D imaging techniques, it reduces the requirements for orbit control and radar system parameters. To sum up, the proposed 3D imaging method with composite registration guarantees imaging efficiency, while enhancing the imaging accuracy of crucial areas with limited data. [ABSTRACT FROM AUTHOR]

The unmanned aerial vehicle (UAV)-borne video synthetic aperture radar (SAR) possesses the characteristic of having high-continuous-frame-rate imaging, which is conducive to the real-time monitoring of ground-moving targets. The real-time imaging-processing system for UAV-borne video SAR (ViSAR) requires miniaturization, low power consumption, high frame rate, and high-resolution imaging. In order to achieve high-frame-rate real-time imaging on limited payload-carrying platforms, this study proposes a miniaturization design of a high-integration UAV-borne ViSAR real-time imaging-processing component (MRIPC). The proposed design integrates functions such as broadband signal generation, high-speed real-time sampling, and real-time SAR imaging processing on a single-chip FPGA. The parallel access mechanism using multiple sets of high-speed data buffers increases the data access throughput and solves the problem of data access bandwidth. The range-Doppler (RD) algorithm and map-drift (MD) algorithm are optimized using parallel multiplexing, achieving a balance between computing speed and hardware resources. The test results have verified that our proposed component is effective for the real-time processing of 2048 × 2048 single-precision floating-point data points to realize a 5 Hz imaging frame rate and 0.15 m imaging resolution, satisfying the requirements of real-time ViSAR-imaging processing. [ABSTRACT FROM AUTHOR]

Synthetic aperture radar (SAR) enables precise object localization and imaging, which has propelled the rapid development of algorithms for maritime ship identification and detection. However, most current deep learning-based algorithms tend to increase network depth to improve detection accuracy, which may result in the loss of effective features of the target. In response to this challenge, this paper innovatively proposes an object-enhanced network, OE-YOLO, designed specifically for SAR ship detection. Firstly, we input the original image into an improved CFAR detector, which enhances the network's ability to localize and perform object extraction by providing more information through an additional channel. Additionally, the Coordinate Attention mechanism (CA) is introduced into the backbone of YOLOv7-tiny to improve the model's ability to capture spatial and positional information in the image, thereby alleviating the problem of losing the position of small objects. Furthermore, to enhance the model's detection capability for multi-scale objects, we optimize the neck part of the original model to integrate the Asymptotic Feature Fusion (AFF) network. Finally, the proposed network model is thoroughly tested and evaluated using publicly available SAR image datasets, including the SAR-Ship-Dataset and HRSID dataset. In comparison to the baseline method YOLOv7-tiny, OE-YOLO exhibits superior performance with a lower parameter count. When compared with other commonly used deep learning-based detection methods, OE-YOLO demonstrates optimal performance and more accurate detection results. [ABSTRACT FROM AUTHOR]

In synthetic aperture radar (SAR) imaging, intelligent object detection methods are facing significant challenges in terms of model robustness and application security, which are posed by adversarial examples. The existing adversarial example generation methods for SAR object detection can be divided into two main types: global perturbation attacks and local perturbation attacks. Due to the dynamic changes and irregular spatial distribution of SAR coherent speckle backgrounds, the attack effectiveness of global perturbation attacks is significantly reduced by coherent speckle. In contrast, by focusing on the image objects, local perturbation attacks achieve targeted and effective advantages over global perturbations by minimizing interference from the SAR coherent speckle background. However, the adaptability of conventional local perturbations is limited because they employ a fixed size without considering the diverse sizes and shapes of SAR objects under various conditions. This paper presents a framework for region-adaptive local perturbations (RaLP) specifically designed for SAR object detection tasks. The framework consists of two modules. To address the issue of coherent speckle noise interference in SAR imagery, we develop a local perturbation generator (LPG) module. By filtering the original image, this module reduces the speckle features introduced during perturbation generation. It then superimposes adversarial perturbations in the form of local perturbations on areas of the object with weaker speckles, thereby reducing the mutual interference between coherent speckles and adversarial perturbation. To address the issue of insufficient adaptability in terms of the size variation in local adversarial perturbations, we propose an adaptive perturbation optimizer (APO) module. This optimizer adapts the size of the adversarial perturbations based on the size and shape of the object, effectively solving the problem of adaptive perturbation size and enhancing the universality of the attack. The experimental results show that RaLP reduces the detection accuracy of the YOLOv3 detector by 29.0%, 29.9%, and 32.3% on the SSDD, SAR-Ship, and AIR-SARShip datasets, respectively, and the model-to-model and dataset-to-dataset transferability of RaLP attacks are verified. [ABSTRACT FROM AUTHOR]

The bistatic Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of monostatic dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration. Unmanned aerial vehicles (UAVs) equipped with bistatic InSAR, having relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne bistatic InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne bistatic InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision bistatic InSAR imaging, and interferometric processing. Height inversion results based on the proposed method are also provided, which demonstrate the effectiveness of the proposed method in improving the accuracy of interferometric measurement at calibration points from 0.66 m to 0.42 m. [ABSTRACT FROM AUTHOR]

In complex environments, the clutter statistical characteristics of synthetic aperture radar (SAR) are inconstant, and the constant detection performance of a false alarm rate (CFAR) detector based on a clutter statistical model is also hard to achieve. As a result, the overestimated threshold leads to a degradation in detection probability. To this end, this paper proposes a SAR ship detector different from CFAR detectors, which is independent of traditional clutter statistical distribution models and the probability of a false alarm (PFA). The proposed detector aims to raise the ship detection probability and alleviate interference from complex environments such as multi-target areas, shores, and breakwaters. It estimates clutter-truncated thresholds based on clutter intensity statistics (CIS). Firstly, three statistical parameters, including the mean, standard deviation, and maximum intensity of background clutter contaminated by outliers, are calculated; secondly, these parameters are utilized to estimate the clutter-truncated threshold using the novel CIS; and finally, the pixel under test is determined according to the CIS detection rule. Compared with CFAR-based algorithms, CIS obtains a high probability of detection in complex environments. As for other aspects, the CIS detector is insensitive to the structure of the detection window, as well as the size. It is also computationally efficient due to its simple calculations. The superiority of the CIS detector is validated on scene-differed SAR images from the DSSDD dataset. [ABSTRACT FROM AUTHOR]

A space-borne remote sensing method was applied, validated, and demonstrated in a case study on the Samuel de Champlain Bridge in Montreal, Canada. High-resolution C-band radar satellite imagery was analyzed using the Persistent Scatterer Interferometric Synthetic Aperture Radar technique to derive bridge displacements and compare them against theoretical estimates. Multispectral and long-wave thermal infrared satellite imagery acquired during the InSAR observation period and historical environmental data were analyzed to provide context for the interpretation and understanding of InSAR results. Thermal deformation measurements compared well with their theoretical estimates based on known bridge geometry and ambient temperature data. Non-thermal deformation measurements gave no evidence of settlement during the 2-year monitoring period, as would normally be expected for a newly constructed bridge with its foundation on bedrock. The availability of environmental data obtained from multispectral and thermal infrared satellite imagery was found to be useful in providing context for the bridge stability assessment. Ambient temperature measurements from thermal infrared satellite imagery were found to be a suitable alternative in cases where data from in situ temperature sensors or nearby weather stations are not available or not fit for purpose. No strong correlation was found between the river conditions and bridge deformation results from the InSAR analysis; this is partly due to the fact that most of these effects act along the river flow in the north–south direction, to which the satellite sensor is not sensitive. [ABSTRACT FROM AUTHOR]

This paper presents a methodology to detect the coastal erosion and progradation effects in the 'Atrato River' delta, located in the Gulf of Urabá in Colombia, using SAR (Synthetic Aperture Radar) images. Erosion is the physical–mechanical loss of the soil that affects its functions and ecosystem services while producing a reduction in its productive capacity. Progradation is the deposition of layers in the basinward direction while moving coastward. Other studies have investigated these two phenomena using optical images, encountering difficulties due to the persistent presence of clouds in this region. In order to avoid the cloud effects, in this study, we used 16 Sentinel 1 SAR images with two different polarizations between 2016 and 2023. First, each image was rescaled from 0 to 255, then the image was despeckled by a deep learning (DL) model. Afterwards, a single RGB image was composed with the filtered polarizations. Next, a classifier with 99% accuracy based on Otsu's method was used to determine whether each pixel was water or not. Then, the classified image was registered to a reference one using Oriented FAST and Rotated BRIEF (ORB) descriptor. Finally, a multitemporal analysis was performed by comparing every image to the previous one to identify the studied phenomena, calculating areas. Also, all images were integrated to obtain a heatmap that showed the overall changes across eight years (2016–2023) in a single image. The multitemporal analysis performed found that the newly created mouth is the most active area for these processes, coinciding with other studies. In addition, a comparison of these findings with the Oceanic Niño Index (ONI) showed a relative delayed coupling to the erosion process and a coupling of progradation with dry and wet seasons. [ABSTRACT FROM AUTHOR]

Interferometric synthetic aperture radar (InSAR) processing techniques have been widely used to derive surface deformation or retrieve terrain elevation. Over the development of the past few decades, most research has mainly focused on its application, new techniques for improved accuracy, or the investigation of a particular error source and its correction method. Therefore, a thorough discussion about each error source and its influence on InSAR-derived products is rarely addressed. Additionally, InSAR is a challenging topic for beginners to learn due to the intricate mathematics and the necessary signal processing knowledge required to grasp the core concepts. This results in the fact that existing papers about InSAR are easy to understand for those with a technical background but difficult for those without. To cope with the two issues, this paper aims to provide an organized, comprehensive, and easily understandable review of the InSAR error budget. In order to assist readers of various backgrounds in comprehending the concepts, we describe the error sources in plain language, use the most fundamental math, offer clear examples, and exhibit numerical and visual comparisons. In this paper, InSAR-related errors are categorized as intrinsic height errors or location-induced errors. Intrinsic height errors are further divided into two subcategories (i.e., systematic and random error). These errors can result in an incorrect number of phase fringes and introduce unwanted phase noise into the output interferograms, respectively. Location-induced errors are the projection errors caused by the slant-ranging attribute of the SAR systems and include foreshortening, layover, and shadow effects. The main focus of this work is on systematic and random error, as well as their effects on InSAR-derived topographic and deformation products. Furthermore, because the effects of systematic and random errors are greatly dependent on radar wavelengths, different bands are utilized for comparison, including L-band, S-band, C-band, and X-band scenarios. As examples, we used the parameters of the upcoming NISAR operation to represent L-band and S-band, ERS-1 and Sentinel-1 to represent C-band, and TerraSAR-X to represent X-band. This paper seeks to bridge this knowledge gap by presenting an approachable exploration of InSAR error sources and their implications. This robust and accessible analysis of the InSAR error budget is especially pertinent as more SAR data products are made available (e.g., NISAR, ICEYE, Capella, Umbra, etc.) and the SAR user-base continues to expand. Finally, a commentary is offered to explore the error sources that were not included in this work, as well as to present our thoughts and conclusions. [ABSTRACT FROM AUTHOR]

Frequency synchronization error, as one of the inevitable technical challenges in distributed synthetic aperture radar (SAR), has different impacts on different SAR systems. Multi-monostatic SAR is a typical distributed configuration where frequency synchronization errors are tiny in distributed airborne and low earth orbit (LEO) SAR systems. However, due to the long time delay and long synthetic aperture time, the imaging performance of a multi-monostatic geosynchronous (GEO) SAR system is affected by frequency oscillator errors. In this paper, to investigate the frequency synchronization problem in this configuration, we firstly model the echo signals with the frequency synchronization errors, which can be divided into fixed frequency errors and random phase noise. Secondly, we talk about the impacts of the two kinds of errors on imaging performance. To solve the problem, we thirdly propose an autofocus back-projection (ABP) algorithm, which adopts the coordinate descent method and iteratively adjusts the phase error estimation until the image reaches its maximum sharpness. Based on the characteristics of the frequency synchronization errors, we further propose the Node ABP (NABP) algorithm, which greatly reduces the amount of storage and computation compared to the ABP algorithm. Finally, simulations are carried out to validate the effectiveness of the ABP and NABP algorithms. [ABSTRACT FROM AUTHOR]

The internal waves in the South China Sea are highly correlated with the tidal currents in the Luzon Strait, which makes it possible to establish an internal wave prediction model based on internal wave kinematics. However, the kinematic model requires the input of the exact location and time of the initial internal wave for which the generation mechanism of internal waves in the northern South China Sea must be well understood. By analyzing the internal wave field in the northern South China Sea (SCS) simulated using the MIT General Circulation Model (MITgcm) and observations from satellite synthetic aperture radar (SAR) and mooring temperature–salinity–depth (TSD) chains, the source regions and propagation initiation times of internal waves are identified for three typical tidal phases, i.e., the diurnal-tide-dominated phase (DTP), transition tide phase (TTP), and semidiurnal-tide-dominated phase (STP). The generation procedures of Type A and Type B internal waves are discussed in detail with those data. The present study reveals that Type A and Type B waves are generated at the eastern and western ridges, respectively, and both commence their westward propagation at the peak of the eastward tidal flow. The dynamics of lee waves and the resonance effect with double ridges constitute the generation mechanisms of internal waves in the northern SCS. Combined with varying configurations of tidal conditions, topography, and stratification, the generation procedures of Type A and Type B waves in the DTP, TTP, and STP are elucidated with the generation mechanism in a unified and self-consistent way. In short, during DTP, weaker A waves alternate with weaker B waves each day; during TTP, strong A waves and strong B waves appear alternately every day; and there are two weak A waves per day during the STP. The generation mechanism can help in developing future empirical models for generating internal waves using tidal currents, topography, and stratification without requiring complex fluid dynamics calculations. [ABSTRACT FROM AUTHOR]

With the acceleration of urbanisation, urban areas are subject to the combined effects of the accumulation of various natural factors, such as changes in temperature leading to the thermal expansion or contraction of surface materials (rock, soil, etc.) and changes in precipitation and humidity leading to an increase in the self-weight of soil due to the infiltration of water along the cracks or pores in the ground. Therefore, the subsidence of urban areas has now become a serious geological disaster phenomenon. However, the use of traditional neural network prediction models has limitations when examining the causal relationships between time series surface deformation data and multiple influencing factors and when applying multiple influencing factors for predictive analyses. To this end, Sentinel-1A data from March 2017 to February 2023 were used as the data source in this paper, based on time series deformation data acquired using the small baseline subset interferometric synthetic aperture radar (SBAS-InSAR) technique. A sparrow search algorithm–convolutional neural network–long short-term memory (SSA-CNN-LSTM) neural network prediction model was built. The six factors of temperature, humidity, precipitation, and ground temperature at three different depths below the surface (5 cm, 10 cm, and 15 cm) were taken as the input of the model, and the surface deformation data were taken as the output of the neural network model. The correlation between the spatial and temporal evolution characteristics of the ground subsidence in urban areas and various influencing factors was analysed using grey correlation analysis, which proved that these six factors contribute to some extent to the deformation of the urban surface. The main urban area of Hohhot City, Inner Mongolia Autonomous Region, was used as the study area. In order to verify the efficacy of this neural network prediction model, the prediction effects of the multilayer perceptron (MLP), backpropagation (BP), and SSA-CNN-LSTM models were compared and analysed, with the values of the correlation coefficients of the feature points of A1, B1, and C1 being in the range of 0.92, 0.83, and 0.93, respectively. The results show that compared with the traditional MLP and BP neural network models, the SSA-CNN-LSTM model achieves a higher performance in predicting time series surface deformation data in urban areas, which provides new ideas and methods for this area of research. [ABSTRACT FROM AUTHOR]

Ship wake detection using synthetic aperture radar (SAR) imagery provides a way to obtain small marine ship information, but it often becomes unavailable and unreliable during a high sea state. Polarimetric information provides a potential way to solve this problem, which can enhance the ship target as well as the ship wake features. However, three challenges still exist in ship wake detection in polarimetric SAR imagery: the unwanted influences of bright and singular points on ship wake detection, the lack of performance analysis of wake detection by new-type polarimetric enhancement methods, and the difficulty of using the assessment criteria for ship wake detection. In this paper, we try to solve the above problems. Firstly, fully polarized SAR imagery of both ship turbulent and Kelvin wake is simulated based on the two-scale composite model, and the Polarimetric Whitening Filter (PWF) and Polarimetric Detection Optimization Filter (PDOF) are applied to the simulated fully polarized SAR imagery to enhance the ship wake features. Secondly, since the bright and singular points resulting from the ship echoes and the polarimetric enhancement methods may lead to misdetections, a logarithm process and z-score normalization pre-processing has been applied to the images. Then, a new assessment criterion for wake detection performance has been formulated, and the probability of missing detections (PMDs) and the probability of false alarms (PFAs) have been defined for two different requirements. And a Radon transform-based ship wake detection method for both ship turbulence and Kelvin wake has been carried out in horizontal–horizontal (HH), vertical–vertical (VV), horizontal–vertical (HV), PWF and PDOF SAR imagery. Finally, an analysis of the wake detection performance has been carried out. The PWF and PDOF can improve the wake detection performance by an average of nearly 50 percent compared with the HH and VV. [ABSTRACT FROM AUTHOR]

The frequent occurrence of global flood disasters leads to millions of people falling into poverty each year, which poses immense pressure on governments and hinders social development. Therefore, providing more data support for flood disaster detection is of paramount importance. To facilitate the development of water body detection algorithms, we create the DaliWS dataset for water segmentation, which contains abundant pixel-level annotations, and consists of high spatial resolution SAR images collected from the GaoFen-3 (GF-3) satellite. For comprehensive analysis, extensive experiments are conducted on the DaliWS dataset to explore the performance of the state-of-the-art segmentation models, including FCN, SegNeXt, U-Net, and DeeplabV3+, and investigate the impact of different polarization modes on water segmentation. Additionally, to probe the generalization of our dataset, we further evaluate the models trained with the DaliWS dataset, on publicly available water segmentation datasets. Through detailed analysis of the experimental results, we establish a valuable benchmark and provide usage guidelines for future researchers working with the DaliWS dataset. The experimental results demonstrate the F1 scores of FCN, SegNeXt, U-Net, and DeeplabV3+ on the dual-polarization data of DaliWS dataset reach to 90.361%, 90.192%, 92.110%, and 91.199%, respectively, and these four models trained using the DaliWS dataset exhibit excellent generalization performance on the public dataset, which further confirms the research value of our dataset. [ABSTRACT FROM AUTHOR]

By means of alteration of the transmitted linear frequency modulation (LFM) signal waveform parameters, such as pulse width or chirp rate, initial phase, pulse repetition interval (PRI), and chirp rate polarity at every position of synthetic apertures, the pseudo-random agility technology of interpulse waveform parameters in airborne Synthetic Aperture Radar (SAR) actively increases the complexity and uncertainty of radar waveforms. This technology confuses jamming interception receivers, thus improving its anti-interference ability for active coherent jamming, which is one of the main research interests of airborne SAR technology. But the pseudo-random agility technology for interpulse waveform parameters faces certain challenges of large computation and complex system design, which need to be further studied and solved. To address these issues, a processing scheme of high-resolution SAR image formation which is appropriate for agile interpulse waveform parameters is proposed in this paper. This method can deal with multiple agile parameters, not only single ones as in most existing literature. Its computation load is nearly comparable to that of traditional SAR image formation with constant waveform parameters. The high-resolution SAR imaging results obtained by processing SAR raw data with agile interpulse waveform parameters demonstrate the effectiveness of the proposed method. In addition, real SAR images with resolutions of 0.5 m and 0.15 m, which are rarely found in the public literature, are shown under the circumstance of randomly changing the transmitted wideband LFM signal pulse parameters one by one. [ABSTRACT FROM AUTHOR]

The assessment of forest structural parameters is crucial for understanding carbon storage, habitat suitability, and timber stock. However, the labor-intensive and expensive nature of field measurements, coupled with inadequate sample sizes for large-scale modeling, poses challenges. To address the forest structure parameters in the Western Tianshan Mountains, this study used UAV-LiDAR to gather extensive sample data. This approach was enhanced by integrating Sentinel satellite and topographic data and using a Bayesian-Random Forest model to estimate forest canopy height, average height, density, and aboveground biomass (AGB). Validation against independent LiDAR-derived samples confirmed the model's high accuracy, with coefficients of determination (R2) and root mean square errors (RMSE) indicating strong predictive performance (R2 = 0.63, RMSE = 5.06 m for canopy height; R2 = 0.64, RMSE = 2.88 m for average height; R2 = 0.68, RMSE = 62.84 for density; and R2 = 0.59, RMSE = 29.71 Mg/ha for AGB). Notably, the crucial factors include DEM, Sentinel-1 (VH and VV backscatter in dB), and Sentinel-2 (B6, B8A, and B11 bands). These factors contribute significantly to the modeling of forest structure. This technology aims to expedite and economize forest surveys while augmenting the range of forest parameters, especially in remote and rugged terrains. Using a wealth of UAV-LiDAR data, this outcome surpasses its counterparts' by providing essential insights for exploring climate change effects on Central Asian forests, facilitating precise carbon stock quantification, and enhancing knowledge of forest ecosystems. [ABSTRACT FROM AUTHOR]

This paper investigates a real-time process generator of wideband signals, which calculates waveforms in a field-programmable gate array (FPGA) using the high-level synthesis (HLS) method. To obtain high-resolution and wide-swath images, the generator must produce multiple modes of large time-bandwidth product (TBP) linear frequency modulation (LFM) signals. However, the conventional storage method is unrealistic as it requires huge storage resources to save pre-computed waveforms. Therefore, this paper proposes a novel processing approach that calculates waveforms in real-time based simply on parameters such as the sampling frequency, bandwidth, and time width. Additionally, this paper implements predistortion through the polynomial curve to approximate phase errors of the system. The parallelizing process in the FPGA is necessary to satisfy the high-speed requirement of a digital-to-analog converter (DAC); however, repeatedly multiplexing real-time calculation consumes extensive logic and DSP resources, potentially exceeding FPGA limitations. To address this, this paper proposes a piecewise linear algorithm to conserve resources, which processes the polynomial only once, acquires the difference in two adjacent values through the register and pipeline, and then adds this increment to facilitate parallel computations. The performance of this proposed generator is validated through simulation and implemented in experiments with an X-band airborne SAR system. [ABSTRACT FROM AUTHOR]

With the increasing use of the strategy and group target attack method in the modern battlefield, multi-target inverse synthetic aperture radar (ISAR) imaging simultaneously with high efficiency draws more and more attention, which gives a promising prospect for aerospace target detection and recognition in the multi-target scenario. To overcome the shortcomings of traditional multi-target imaging with one beam at one pulse repetition time (PRT) based on phase array radar (PAR), this paper proposes a novel multi-target imaging waveform design method based on the newly full digital array radar (DAR). Firstly, we propose using radar waveform diversity with 2D orthogonality to realize multi-target ISAR imaging with high imaging quality and efficiency. Then, to meet the constant modulus requirement for maximizing the transmitting power, orthogonal frequency division multiplexing (OFDM) chirp theory is proposed to directly generate the transmit waveform instead of the traditional optimization method with the nonconvex problem for waveform design. Based on time-variant weighted and time diversity technology, a of group transmit waveforms is designed, which can form multiple beams simultaneously and make the signals arriving at different targets approximately orthogonal. Finally, simulations and experiments are carried out to demonstrate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

The Baihetan reservoir region is characterized by complex geomorphology, significant altitude differences, and rugged terrain. Geological hazards in such areas are often characterized by high concealment, wide distribution, and difficulty in field investigation. Traditional identification techniques are unable to detect and monitor geological hazards on a large scale with high efficiency and accuracy. In recent decades, interferometric synthetic aperture radar (InSAR) techniques, such as small baseline subset InSAR (SBAS-InSAR), have been widely applied to landslide identification. However, due to factors such as vegetation and the degree of landslide deformation, single-band synthetic aperture radar (SAR) still has certain limitations in detecting landslides. In this study, SBAS-InSAR was conducted based on ALOS-2 and Sentinel-1 ascending-descending images covering the Baihetan reservoir region. Deformation identification results were utilized to conduct a statistical analysis of the SAR detection performance and landslide characteristics, and the effect of vegetation on the detection effectiveness of different SAR bands was discussed. The study revealed that when surface vegetation coverage reaches a high degree, the percentage of areas with coverage greater than 0.6 is greater than 95%, the SAR coherence is mainly affected by vegetation thickness; the comparison of the difference change in the average coherence of the C/L bands among the four vegetation types shows that the ratio of the average coherence of the L-bands to the C-bands increases by a factor of three with the increase in thickness and the transition from crops to shrubs and trees. The results showed that the L-band has better detectability than the C-band in alpine-canyon terrain with vegetation coverage and complex vegetation composition. However, considering the high temporal resolution and accessibility of Sentinel-1 SAR data, it is still the main data choice for wide-area identification of landslides in the reservoir area, while other satellite-borne SAR data with different wavelengths and resolutions, such as ALOS, can be used to assist in the identification and monitoring of landslide hazards with significant magnitude of deformations and dense vegetation coverage. Therefore, the combined utilization of multi-band SAR data has the potential to enhance the dependability of landslide identification and monitoring, resulting in more accurate detection results. [ABSTRACT FROM AUTHOR]

The utilization of deep learning in Synthetic Aperture Radar (SAR) Automatic Target Recognition (ATR) has witnessed a recent surge owing to its remarkable feature extraction capabilities. Nonetheless, deep learning methodologies are often encumbered by inadequacies in labeled data and the protracted nature of training processes. To address these challenges and offer an alternative avenue for accurately extracting image features, this paper puts forth a novel and distinctive network dubbed the Capsule Broad Learning System Network for robust SAR ATR (CBLS-SARNET). This novel strategy is specifically tailored to cater to small-sample SAR ATR scenarios. On the one hand, we introduce a United Division Co-training (UDC) Framework as a feature filter, adeptly amalgamating CapsNet and the Broad Learning System (BLS) to enhance network efficiency and efficacy. On the other hand, we devise a Parameters Sharing (PS) network to facilitate secondary learning by sharing the weight and bias of BLS node layers, thereby augmenting the recognition capability of CBLS-SARNET. Experimental results unequivocally demonstrate that our proposed CBLS-SARNET outperforms other deep learning methods in terms of recognition accuracy and training time. Furthermore, experiments validate the generalization and robustness of our novel method under various conditions, including the addition of blur, Gaussian noise, noisy labels, and different depression angles. These findings underscore the superior generalization capabilities of CBLS-SARNET across diverse SAR ATR scenarios. [ABSTRACT FROM AUTHOR]

Radio frequency interference (RFI) poses major threats to synthetic aperture radar (SAR) systems. Due to the suppression of useful target signals via high-power RFI, the SAR imaging quality is severely degraded. Nevertheless, existing studies on RFI mitigation mainly focus on narrowband filtering, while wideband RFI mitigation methods are relatively lacking and perform non-robustly. In this paper, an RFI mitigation scheme is proposed based on instantaneous spectrum forward consecutive mean excision (FCME), which is suitable for both narrowband and wideband RFI mitigation. The SAR echo signal is first transformed into a time–frequency (TF) domain through a short-time Fourier transform (STFT). On this basis, the instantaneous spectra polluted via RFI are detected via a kurtosis-based statistical test and then filtered via FCME to achieve RFI mitigation. Finally, connected component analysis is applied as a safety measure so as to avoid the unnecessary loss of useful target signal. The combination of FCME and connected component analysis enables the proposed method to thoroughly filter out RFI while retaining more useful target signals compared with other competing methods. The experimental results on real SAR raw data validate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Machine learning and deep neural networks have shown satisfactory performance in the supervised classification of Polarimetric Synthetic Aperture Radar (PolSAR) images. However, the PolSAR image classification task still faces some challenges. First, the current form of model input used for this task inevitably involves tedious preprocessing. In addition, issues such as insufficient labels and the design of the model also affect classification performance. To address these issues, this study proposes an augmentation method to better utilize the labeled data and improve the input format of the model, and an end-to-end PolSAR image global classification is implemented on our proposed hybrid network, PolSARMixer. Experimental results demonstrate that, compared to existing methods, our proposed method reduces the steps for the classification of PolSAR images, thus eliminating repetitive data preprocessing procedures and significantly improving classification performance. [ABSTRACT FROM AUTHOR]

The UAV-borne video SAR (ViSAR) imaging system requires miniaturization, low power consumption, high frame rates, and high-resolution real-time imaging. In order to satisfy the requirements of real-time imaging processing for the UAV-borne ViSAR under limited memory and parallel computing resources, this paper proposes a method of embedded GPU-based real-time imaging processing for the UAV-borne ViSAR. Based on a parallel programming model of the compute unified device architecture (CUDA), this paper designed a parallel computing method for range-Doppler (RD) and map drift (MD) algorithms. By utilizing the advantages of the embedded GPU characterized with parallel computing, we improved the processing speed of real-time ViSAR imaging. This paper also adopted a unified memory management method, which greatly reduces data replication and communication latency between the CPU and the GPU. The data processing of 2048 × 2048 points took only 1.215 s on the Jetson AGX Orin platform to form a nine-consecutive-frame image with a resolution of 0.15 m, with each frame taking only 0.135 s, enabling real-time imaging at a high frame rate of 5 Hz. In actual testing, continuous mapping can be achieved without losing the scenes, intuitively obtaining the dynamic observation effects of the area. The processing results of the measured data have verified the reliability and effectiveness of the proposed scheme, satisfying the processing requirements for real-time ViSAR imaging. [ABSTRACT FROM AUTHOR]

Differential SAR Interferometry is a largely exploited technique to study ground deformations. A key application is the detection of the effects promoted by earthquakes, including detailed variations in ground deformations at different scales. In this work, an implemented Python script (Snap2DQuake) based on the "snappy" module by SNAP software 9.0.8 (ESA) for the processing of satellite imagery is proposed. Snap2DQuake is aimed at producing detailed coseismic deformation maps using Sentinel-1 C-band data by the DInSAR technique. With this alternative approach, the processing is simplified, and several issues that may occur using the software are solved. The proposed tool has been tested on two case studies: the Mw 6.4 Petrinja earthquake (Croatia, December 2020) and the Mw 5.7 to Mw 6.3 earthquakes, which occurred near Tyrnavós (Greece, March 2021). The earthquakes, which occurred in two different tectonic contexts, are used to test and verify the validity of Snap2DQuake. Snap2DQuake allows us to provide detailed deformation maps along the vertical and E-W directions in perfect agreement with observations reported in previous works. These maps offer new insights into the deformation pattern linked to earthquakes, demonstrating the reliability of Snap2DQuake as an alternative tool for users working on different applications, even with basic coding skills. [ABSTRACT FROM AUTHOR]

Synthetic aperture radar (SAR) is an important tool for observing the oceanic internal wave phenomenon. However, owing to the unstable imaging quality of SAR on oceanic internal waves, the texture details of internal wave images are usually unclear, which is not conducive to the subsequent applications of the images. To cope with this problem, a texture enhancement method for oceanic internal wave SAR images is proposed in this paper, which is based on non-local mean (NLM) filtering and texture layer enhancement (TLE). Since the strong speckle noise commonly present in internal wave images is simultaneously enhanced during texture enhancement, resulting in degraded image quality, NLM filtering is first performed to suppress speckle noise. Then, the denoised image is decomposed into the structure layer and the texture layer, and a texture layer enhancement method oriented to the texture characteristics of oceanic internal waves is proposed and applied. Finally, the enhanced texture layer and the structure layer are combined to reconstruct the final enhanced image. Experiments are conducted based on the Gaofen-3 real SAR data, and the results demonstrate that the proposed method performs well in suppressing speckle noise, maintaining overall image brightness, and enhancing internal wave texture details. [ABSTRACT FROM AUTHOR]