Search

In synthetic aperture radar (SAR) signal processing, compared with the raw data of level-0, level-1 SAR images are more readily accessible and available in larger quantities. However, an amount of level-1 images are affected by radio frequency interference (RFI), which typically originates from Linear Frequency Modulation (LFM) signals emitted by ground-based radars. Existing research on interference suppression in level-1 data has primarily focused on two methods: transforming SAR images into simulated echo data for interference suppression, or focusing interference in the frequency domain and applying notching filters to reduce interference energy. However, these methods overlook the effective utilization of the interference parameters or are confined to suppressing only one type of LFM interference at a time. In certain SAR images, multiple types of LFM interference manifest bright radiation artifacts that exhibit varying lengths along the range direction while remaining constant in the azimuth direction. It is necessary to suppress multiple LFM interference on SAR images when original echo data are unavailable. This article proposes a joint sparse recovery algorithm for interference suppression in the SAR image domain. In the SAR image domain, two-dimensional LFM interference typically exhibits differences in parameters such as frequency modulation rate and pulse width in the range direction, while maintaining consistency in the azimuth direction. Based on this observation, this article constructs a series of focusing operators for LFM interference in SAR images. These operators enable the sparse representation of dispersed LFM interference. Subsequently, an optimization model is developed that can effectively suppress multi-LFM interference and reduce image loss with the assistance of a regularization term in the image domain. Simulation experiments conducted in various scenarios validate the superior performance of the proposed method. [ABSTRACT FROM AUTHOR]

Radio frequency interference (RFI) poses major threats to synthetic aperture radar (SAR) systems. Due to the suppression of useful target signals via high-power RFI, the SAR imaging quality is severely degraded. Nevertheless, existing studies on RFI mitigation mainly focus on narrowband filtering, while wideband RFI mitigation methods are relatively lacking and perform non-robustly. In this paper, an RFI mitigation scheme is proposed based on instantaneous spectrum forward consecutive mean excision (FCME), which is suitable for both narrowband and wideband RFI mitigation. The SAR echo signal is first transformed into a time–frequency (TF) domain through a short-time Fourier transform (STFT). On this basis, the instantaneous spectra polluted via RFI are detected via a kurtosis-based statistical test and then filtered via FCME to achieve RFI mitigation. Finally, connected component analysis is applied as a safety measure so as to avoid the unnecessary loss of useful target signal. The combination of FCME and connected component analysis enables the proposed method to thoroughly filter out RFI while retaining more useful target signals compared with other competing methods. The experimental results on real SAR raw data validate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Synthetic Aperture Radar (SAR) is a high-resolution imaging sensor commonly mounted on platforms such as airplanes and satellites for widespread use. In complex electromagnetic environments, radio frequency interference (RFI) severely degrades the quality of SAR images due to its widely varying bandwidth and numerous unknown emission sources. Although traditional deep learning-based methods have achieved remarkable results by directly processing SAR images as visual ones, there is still considerable room for improvement in their performance due to the wide coverage and high intensity of RFI. To address these issues, this paper proposes the fusion of segmentation and inpainting networks (FuSINet) to suppress SAR RFI in the time-frequency domain. Firstly, to weaken the dominance of RFI in SAR images caused by high-intensity interference, a simple CCN-based network is employed to learn and segment the RFI. This results in the removal of most of the original interference, leaving blanks that allow the targets to regain dominance in the overall image. Secondly, considering the wide coverage characteristic of RFI, a U-former network with global information capture capabilities is utilized to learn the content covered by the interference and fill in the blanks created by the segmentation network. Compared to the traditional Transformer, this paper enhances its global information capture capabilities through shift-windows and down-sampling layers. Finally, the segmentation and inpainting networks are fused together through a weighted parameter for joint training. This not only accelerates the learning speed but also enables better coordination between the two networks, leading to improved RFI suppression performance. Extensive experimental results demonstrate the substantial performance enhancement of the proposed FuSINet. Compared to the PISNet+, the proposed attention mechanism achieves a 2.49 dB improvement in peak signal-to-noise ratio (PSNR). Furthermore, compared to Uformer, the FuSINet achieves an additional 4.16 dB improvement in PSNR. [ABSTRACT FROM AUTHOR]

For synthetic aperture microwave radiometers, the problem of Radio Frequency Interference (RFI) is becoming more and more serious, which affects both the scientific retrieval of remote sensing data and the imaging quality of brightness temperature (BT) images. In the visibility data domain, the array factor synthesis algorithm is commonly employed to mitigate RFI sources and their Gibbs trailing. In the BT image domain, the CLEAN algorithm is typical applied to mitigate RFI sources and their Gibbs trailing. However, the array factor synthesis algorithm can result in anomalous BT points near the "zero trap" region, and the CLEAN algorithm will miss some BT points below a certain threshold. In this paper, a Bi-domain combined mitigation algorithm is proposed to mitigate RFI sources and their Gibbs trailing. Following initial mitigation in the visibility data domain, dual thresholds are applied to normalize anomalous BT points near the "zero trap" region, thereby enhancing imaging quality. The effectiveness of the Bi-domain combined mitigation algorithm is verified by using both measured data from SMOS L1A and simulated data. The experimental results demonstrate that the Bi-domain combined mitigation algorithm is superior to the array factor synthesis algorithm and the CLEAN algorithm in mitigating RFI sources and their Gibbs trailing. [ABSTRACT FROM AUTHOR]

Ocean salinity is a pivotal aspect of the ocean dynamic environment. Spaceborne L-band radiometers, like SMOS, Aquarius, and SMAP, offer a comprehensive approach to mapping out large-scale ocean salinity patterns. As China prepares for the launch of the Chinese Ocean Salinity and Soil Moisture Mission (COSM), it is essential to delve into the intricacies of radio frequency interference (RFI) detection, localization, and mitigation. The L-band, in particular, is highly susceptible to RFI. COSM will carry not one but two advanced instruments: a 2-D L-band aperture synthesis microwave radiometer (LASMR) and a 1-D L-C-K band microwave imager combined active and passive (MICAP). This article delves into the current state of RFI research, particularly in recent years, and introduces a fusion method that integrates MICAP and LASMR for more accurate RFI detection, localization, and mitigation. This fusion method relies on an algorithm that constructs localization and intensity objective functions based on the principle of least squares. By optimizing these functions, we can pinpoint the precise location and intensity of RFI. The resulting minimum mitigation residual offers a blueprint for achieving optimal RFI detection, localization, and mitigation. The experimental results, achieved in a controlled anechoic chamber, confirm that this fusion method—when weighted by variance—boosts detection accuracy, refines localization precision, and minimizes residual mitigation errors compared with standalone MICAP or LASMR techniques. [ABSTRACT FROM AUTHOR]