Search

Energy-dispersive x-ray spectroscopy and high-angle annular dark-field in a Cs-corrected scanning transmission electron microscope are employed to characterize the atomic-scale strain distribution in the active region of the InAs-based interband cascade laser. For the first time, energy-dispersive x-ray spectroscopy is utilized for the quantitative calculation of the zero-strain region, by which the geometric phase analysis of high-angle annular dark-field imaging has been carried out. The strain distribution of the active region with high accuracy has been obtained. The analysis of the out-of-plane strain shows that the active region in the InAs-based interband cascade laser is strain-compensated, while a certain degree of elemental intermixing still exists in the active region. This detailed strain distribution can provide valuable insights into the optimization of the growth conditions for the active region such as growth temperature, V/III flux ratio, and growth process to minimize the elemental intermixing and obtain a better performance interface while maintaining the strain-compensated state. [ABSTRACT FROM AUTHOR]

Packaging insulation materials with high thermal conductivity and excellent dielectric properties are favorable to meet the high demand and rapid development of third generation power semiconductors. In this study, we propose to improve the thermal conductivity of epoxy resin (EP) by incorporating a three-dimensional boron nitride thermally conductive network. Detailedly, polyurethane foam (PU) was used as a supporter, and boron nitride nanosheets (BNNSs) were loaded onto the PU supporter through chemical bonding (BNNS@PU). After immersing BNNS@PU into the EP resin, EP-based thermally conductive composites were prepared by vacuum-assisted impregnation. Fourier transform infrared spectrometer and scanning electron microscope were used to characterize the chemical bonding and morphological structure of BNNS@PU, respectively. The content of BNNS in BNNS@PU/EP composites was quantitatively analyzed by TGA. The results show that the thermal conductivity of the BNNS@PU/EP composites reaches 0.521 W/m K with an enhancement rate η of 30.89 at an ultra-low BNNS filler content (5.93 wt. %). Additionally, the BNNS@PU/EP composites have excellent dielectric properties with the frequency range from 101 to 106 Hz. This paper provides an interesting idea for developing high thermal conductivity insulating materials used for power semiconductor packaging. [ABSTRACT FROM AUTHOR]

Over the last two decades, Electron Energy Loss Spectroscopy (EELS) imaging with a scanning transmission electron microscope has emerged as a technique of choice for visualizing complex chemical, electronic, plasmonic, and phononic phenomena in complex materials and structures. The availability of the EELS data necessitates the development of methods to analyze multidimensional data sets with complex spatial and energy structures. Traditionally, the analysis of these data sets has been based on analysis of individual spectra, one at a time, whereas the spatial structure and correlations between individual spatial pixels containing the relevant information of the physics of underpinning processes have generally been ignored and analyzed only via the visualization as 2D maps. Here, we develop a machine learning-based approach and workflows for the analysis of spatial structures in 3D EELS data sets using a combination of dimensionality reduction and multichannel rotationally invariant variational autoencoders. This approach is illustrated for the analysis of both the plasmonic phenomena in a system of nanowires and in the core excitations in functional oxides using low loss and core-loss EELS, respectively. The code developed in this manuscript is open sourced and freely available and provided as a Jupyter notebook for the interested reader. [ABSTRACT FROM AUTHOR]

Low-energy ion beam irradiation, combined with the introduction of impurities, presents a promising approach for nanopatterning silicon (Si) surfaces. In this research, we investigate the surface evolution of Si (100) surfaces irradiated by 75 eV helium (He) plasma, in the presence of tantalum (Ta), traditionally regarded as an impurity incapable of initiating pattern formation, as evidenced in prior studies. The Ta impurities are pre-deposited onto the Si surfaces using the magnetron sputtering method, which offers a more controlled and quantifiable approach compared with the conventional co-deposition route. After irradiation at 800 K, dense cone arrays are produced on the Si surface. The growth of the cones is explored for fluence spanning (1–10) × 1025 m−2. The cross-sectional scanning electron microscope images indicate that the cone lengths and base width are well characterized by t1/2 dependence. The kinetics of the cone growth follow Fick's law, characterized by an effective diffusive mechanism with the coefficients of diffusion: D = 6.49 ± 0.83 × 10−16 m−2 s−1. Transmission electron microscope observations reveal that the cone has distinct inner and outer parts with different microstructures and a clear interface. The growth mechanism of these cones is elucidated as a composite process involving preferential sputtering, the destabilizing influence of He bubbles, and the migration of adatoms. [ABSTRACT FROM AUTHOR]

Eight kinds of patterned discharges are obtained by changing the discharge parameters in a dielectric barrier discharge with modulated gas gaps, which are applicable to materials patterned treatment. A square superlattice pattern consisting of two dot sublattices and one ring sublattice is studied and used to treat a PI film. The formation mechanism is studied by intensified charge coupled device. The spatial distribution of the plasma parameters is measured using optical emission spectra. The gas temperatures as well as the electron densities of the three sublattices are significantly different from each other. The physical and chemical properties of the treated film are measured using a surface profiler, x-ray photoelectron spectroscopy, and scanning electron microscope. The transmissivity, wettability, and etching depth of the treated PI film demonstrate square superlattice pattern distribution, which verifies the predictions based on plasma parameter measurements. The dielectric barrier discharge device reported here is also applicable to materials' patterned growth. [ABSTRACT FROM AUTHOR]

Nanoscale subsurface characterization technologies based on the scanning electron microscope platform offer incomparable advantages of nondestructiveness and penetration depths up to the micrometer scale. However, the electron beam can serve not just as a mechanical/electrical excitation source but also as an excellent nanoscale thermal excitation source, which can facilitate the development of nanoscale subsurface imaging methods based on the Seebeck effect in semiconducting materials. In this work, a subsurface nondestructive imaging technology, scanning thermoelectric capacitance microscopy (STeCM), was developed based on the interaction between a non-steady-state electron beam and semiconducting materials, exploiting the Seebeck effect. In STeCM, a square wave-modulated hot electron beam with huge kinetic energy excites a "thermal wave" in the subsurface local region of the semiconducting sample. The heated local region, acting as a thermoelectric capacitor, undergoes cyclic charging and discharging, leading to the generation of periodic current due to non-equilibrium carrier migration. The second-order harmonic component of this current is demodulated to visualize embedded local thermal/thermoelectric inhomogeneities. Amazingly, for STeCM sample, only a smooth or polished surface is required, eliminating the need for any microfabrication, which will effectively decrease the configuration difficulty in the experiment. STeCM offers an alternative subsurface nondestructive imaging technology for more efficient, simple, and robust characterization. [ABSTRACT FROM AUTHOR]

The study aimed to develop and analyze bio-based composites, incorporating moringa bioresin and hemp fibers as reinforcing elements. The composites were fabricated using four weight percentage combinations of epoxy, moringa bioresin, and hemp fiber. The fabricated composites were characterized by their mechanical, thermal, water absorption, biodegradability, and morphological properties. The study revealed that the composite with the highest proportion of moringa bioresin (30 wt. %) exhibited better mechanical properties. Moreover, the flexural strength and Shore D hardness were impacted by both the matrix and reinforcing materials' weight percentages. Thermal analysis showed that the composites had good thermal stability, while water absorption analysis indicated that the composites had good water resistance. Biodegradability analysis showed that the composites had a high rate of biodegradation, making them environmentally friendly. The distribution of reinforcing fibers within the matrix material was found to be uniform through the use of scanning electron microscope based morphological analysis. The results indicate that moringa bioresin and hemp fiber composites have the potential to be used as sustainable alternatives to petroleum-based composites in various applications. [ABSTRACT FROM AUTHOR]

It has recently been demonstrated that electron beam injection into p-type β-gallium oxide leads to a significant linear increase in minority carrier diffusion length with injection duration, followed by its saturation. The effect was ascribed to trapping of non-equilibrium electrons (generated by a primary electron beam) at meta-stable native defect levels in the material, which in turn blocks recombination through these levels. In this work, in contrast to previous studies, the effect of electron injection in p-type Ga2O3 was investigated using cathodoluminescence technique in situ in scanning electron microscope, thus providing insight into minority carrier lifetime behavior under electron beam irradiation. The activation energy of ∼0.3 eV, obtained for the phenomenon of interest, is consistent with the involvement of Ga vacancy-related defects. [ABSTRACT FROM AUTHOR]

Polar discontinuities occur in oxide heterostructures due to varying net charges in the sub-unit cell layers. These polar discontinuities lead to structural reconstruction and often create diverse functionalities. This work constructs polar discontinuous in La0.67Sr0.33MnO3/SrCuO2 (LSMO/SCO) heterostructures on a (001)-orientated SrTiO3 (STO) substrate under different configurations. By changing the growth order of LSMO and SCO, we found two different compensating mechanisms for polar discontinuity. When LSMO is grown on SCO, interfacial polarity discontinuities result in the generation of a large number of oxygen vacancies within the LSMO film. Thus, the LSMO magnetism deteriorates. For the SCO/LSMO/SCO trilayer, the SCO capping layer can recover the LSMO magnetism. The scanning transmission electron microscope results show an atomic reconstruction at the SCO-on-LSMO interface and several oxygen vacancies at the SrO sublayer. The interface reconfiguration releases the polar energy, thereby inhibiting the generation of oxygen vacancies and improving the ferromagnetism of the LSMO film. Our work studies the impact of polar discontinuity at the interface, providing insights into the effects of interface polar discontinuities on functional materials. [ABSTRACT FROM AUTHOR]

A pure nickel film and a carbon/nickel (C/Ni) composite film were produced using radio frequency magnetron sputtering. The structure of the films was regulated by adjusting the sputtering power and the time allocation of sputtering nickel and graphite targets. Furthermore, a scanning electron microscope, an x-ray diffractometer, and a Raman spectrometer were employed for sample characterization. The results demonstrated that the thickness of the pure nickel film and C/Ni composite film with a total deposition time of 60 s was between 44.96 and 65.31 nm. The nickel film exhibited preferential growth along the crystal plane (111), and the structure of carbon materials was in the second stage of the three-stage model known as "amorphization trajectory of graphite." The prepared films' electromagnetic interference shielding effectiveness (EMI SE) in the X-band was investigated using a vector network analyzer. It was observed that the C/Ni composite film with a thickness of 44.96 nm demonstrated a superior EMI SE with a maximum value reaching 21 dB. The EMI SE of the C/Ni composite film can reach the same performance and even exceed that of the pure nickel film obtained at the power of 200 W for 60 s in certain frequency segments. In conclusion, the pure nickel film can be replaced by C/Ni composite film prospectively due to their excellent EMI SE along with advantages such as reduced thickness, lighter weight, and lower cost. [ABSTRACT FROM AUTHOR]

We investigated electron emission characteristics of a hafnium carbide [HfC(100)] single-crystal tip at various temperatures toward finding a candidate of the next generation of emitters for electron microscopes. The emission mode changed from cold-field emission (CFE) to low-temperature and high-temperature thermal-field emission and, finally, to extended Schottky emission. The energy width at full width of half maximum of the emitted electrons was 0.2 eV in the CFE mode at an angular current of 20 μA/sr, and it showed good emission stability with current noise less than 3.5% in an electron gun of a scanning electron microscope (SEM). Spatial resolution of the SEM at an acceleration voltage of 0.5 kV improved 14% by using the HfC(100)-CFE tip instead of a conventional W(310)-CFE tip. High monochromaticity and stable electron emission of the HfC(100)-CFE tip are suitable for the next generation of emitters for ultrahigh-resolution field emission SEMs. [ABSTRACT FROM AUTHOR]

This study elucidates the thermal-induced bandgap broadening (TBB) phenomenon in copolymer organic semiconductors (OSCs). From the perspective of device physics, the diketopyrrolopyrrole-based copolymer was employed as the semiconductor layer to fabricate a back-to-back Schottky junction structure. Characterization through the analysis of I–V curves enables the qualitative exploration of the correlation between bandgap and temperature in copolymer OSCs. Then, technology computer-aided design was utilized to explore the influence of thermal-induced bandgap broadening on the back-to-back Schottky I–V curves. Subsequently, the variable temperature UV-VIS-NIR absorption spectra of the copolymer OSCs were analyzed, providing quantitative evidence of the thermal-induced bandgap broadening phenomenon and confirming its recoverability. Through the research of the Schottky junction and absorption spectra, we verified the consistency of the TBB phenomenon in both the electrical and optical bandgaps. From the scanning electron microscope images of the copolymer OSC films, it is found that the thermal-induced bandgap broadening phenomenon is mainly caused by thermal expansion and increased disorder of copolymer molecules. This study highlights a physical phenomenon of copolymer OSCs that is different from most inorganic semiconductors, and such insight offers a theoretical perspective for the application and thermal stability investigation of copolymer devices under high temperature conditions. [ABSTRACT FROM AUTHOR]

Magnesium AZ91/AlN-based surface composites have been synthesized using the friction stir processing (FSP) technique. The influence of particle addition during FSP on microstructural and mechanical properties has been investigated. Composite plates of 5, 10, and 15 vol. % AlN were synthesized using two-pass FSP with an axial force of 10 KN, a tool travel speed of 40 mm/min, and a tool rotation speed of 1200 rpm. The AZ91/AlN surface composites were analyzed microscopically with the use of an optical microscope, an x-ray diffractometer, and a scanning electron microscope. The prepared composites were tested for hardness and tensile strength. Micrographs taken in the stir zone revealed a consistent distribution of AlN particles throughout the AZ91 matrix. The AZ91/AlN surface composites were tested for hardness and tensile strength, and the findings showed that the AlN particles improved the mechanical properties without significantly decreasing ductility. The fracture surfaces of the composites were studied, and the mechanisms of fracture were identified. [ABSTRACT FROM AUTHOR]

Body fluids can potentially indicate the presence of non-small cancer cells. Studying these fluids is an emerging field that could be crucial for cancer detection and monitoring treatment effectiveness. Meanwhile, the examination of fluids on a microscopic level is part of the field of microfluidics. This study focuses on the development of a total analysis system that consists of various interconnected structures that are designed to mix, classify, concentrate, and isolate particles in fluids that mimic the behavior of cancer and normal cells. Using the COMSOL Multiphysics software, the device's performance was optimized to use a pressure input of 35 kPa for water or serum and 29.4 kPa for a mixture of liquid and serum samples, which are the optimal pressure inputs. The numerical models were validated by experiments using two types of polystyrene particles, with diameters of 5 and 20 μm. Moreover, the developed system was applied to monitor the behavior of red blood cells. The microfluidic chip is capable of addressing several challenges through visual detections, including mixing tests of two fluids with similar densities, proper particle size classification using Dean flow fractionation, and single-step recovery of large, labeled particles. Finally, the collected particles were examined using an environmental scanning electron microscope to determine their size, and the results demonstrated that successful size separation was achieved, with particles around 20 μm completely separated from the smaller ones. [ABSTRACT FROM AUTHOR]

Single zinc oxide nanowires (ZnO NWs) are promising for nanogenerators because of their excellent semiconducting and piezoelectric properties, but characterizing the latter efficiently is challenging. As reported here, an electrical breakdown strategy was used to construct single ZnO NWs with a specific length. With the high operability of a nanomanipulator in a scanning electron microscope, ZnO-NW-based two-probe and three-probe structures were constructed for fabricating AC/DC nanogenerators, respectively. For a ZnO NW, an AC output of between −15.31 mV and 5.82 mV was achieved, while for a DC nanogenerator, an output of ∼24.3 mV was realized. Also, the three-probe structure's output method was changed to verify the distribution of piezoelectric charges when a single ZnO NW is bent by a probe, and DC outputs of different amplitudes were achieved. This study provides a low-cost, highly convenient, and operational method for studying the AC/DC output characteristics of single NWs, which is beneficial for the further development of nanogenerators. ARTICLE HIGHLIGHTS: HIGHLIGHTS • A method for reworking NWs to a specific length was achieved using an electrical breakdown strategy based on the constructed electrical loop, and its success rate is high. • With the maneuverability provided by multiple operating units of a nanomanipulator, AC output was investigated for a single ZnO NW with a two-probe structure, as well as DC output with a three-probe structure. • In the three-probe structure, different DC outputs were achieved by changing the position of the NW–probe contact point and the wiring state of the probe, while the distribution of surface piezoelectric potential along the NW's axis was studied. [ABSTRACT FROM AUTHOR]

Strain engineering is an alternative to chemical modification in manipulating functionalities of materials. Here, we report the lattice strain could relax the abrupt phase transition of (Ni1−xFex)1−δS and lead to an excellent negative thermal expansion (NTE) effect. The high-resolution scanning transmission electron microscope and extended x-ray absorption fine structure unambiguously demonstrate that parallel Ni3S4-type nanosheets could be introduced into the matrix lattice by increasing the δ value. By forming the Ni(Fe)-S-Ni(Fe) bonds, the (1–11) plane of nanosheets epitaxially grows on the (002) plane of the hexagonal matrix. Those bonds are strong enough to bear the large lattice mismatch along the interface as the phase transition occurs. As the concentration of nanosheets increases, the weak and inhomogeneous strain in matrix lattice becomes strong and uniform, expanding the NTE window in different ways. This result opens an unconventional avenue for designing NTE materials and extends the research scope of lattice strain as well. [ABSTRACT FROM AUTHOR]

The FurnaSEM microfurnace was installed in the chamber of a scanning electron microscope to carry out in situ experiments at high temperatures and test its limits. The microfurnace was used in combination with different types of detectors (Everhart–Thornley for the collection of secondary electrons in a high vacuum, gas secondary electron detector for the specific collection of secondary electrons in the presence of gas, and Karmen© detector for the collection of backscattered electrons at high temperature). Experiments carried out on various samples (metal alloys and ceramics) show that the microfurnace operates in both high-vacuum and low-vacuum modes. Temperature ramp rates during temperature cycles applied to the sample range from 1 to 120 °C/min (temperature rise) and 1 to 480 °C/min (controlled and natural cooling). The maximum temperature at which images were recorded up to 25 k × magnification was 1340 °C, with a residual air atmosphere of 120 Pa. The choice of a flat furnace with the sample placed directly above it has enabled innovative experiments to be carried out, such as low-voltage imaging (using a shorter working distance—up to 10 mm—than is possible with conventional furnaces), 3D imaging (by tilting the stage by up to 10°), and high-temperature backscattered electron imaging (using a dedicated detector). [ABSTRACT FROM AUTHOR]

When conducting in situ experiments at high temperatures in a scanning electron microscope using microfurnaces, controlling the temperature of a sample of a few mm3 placed in the hot zone of the furnace can be a complex task. In most cases, the temperature of the sample is estimated by means of a thermocouple placed in the hot body of the furnace, and the assumption made is that the temperature of the furnace is the temperature of the sample. In this work, a detailed understanding of the thermal response of the sample placed in the hot zone of the furnace is proposed. Temperature differences due to contact resistance between the furnace surface and the sample, the nature of the sample, and the sample geometry are calculated with a numerical model and measured experimentally on a dedicated test bench. Three technical solutions (bonding, sandwiching, and mini-crucible) for limiting temperature differences between the furnace surface and sample are proposed and validated by numerical calculations and experimental measurements. [ABSTRACT FROM AUTHOR]

The development of a new heating system dedicated to in situ scanning electron microscope (SEM) experimentation at high temperatures is reported. This system, called FurnaSEM, is a compact microfurnace, enabling heat treatments up to 1300 °C. The choice of materials for the microfurnace is explained. The design of the microfurnace is optimized by iterations of numerical simulations, and the thermal characteristics of the microfurnace are calculated numerically. The numerical results obtained are compared with the thermal characteristics of a manufactured microfurnace, measured on a specially developed dedicated test bench. This test bench includes a working chamber simulating a SEM chamber equipped with a thermal camera. The results obtained during various qualification tests enabled us to determine the main technical characteristics of the FurnaSEM microfurnace: temperature profiles on the sample support surface, energy consumption at high temperatures, and the range of achievable thermal cycles. [ABSTRACT FROM AUTHOR]

Compared with continuous wave (CW), pulse wave (PW) perturbation results in a larger temperature change rate inside the cladding layer, which leads to a higher quality cladding layer. In this paper, a three-dimensional numerical model of laser cladding Fe60 powder was established. The multiphysics field coupling transient evolution and solute distribution under PW and CW operating modes were studied. The problem of lack of theoretical support for laser cladding process under different working modes in heat source was solved. Calculations show that at 1970 ms when the temperature is stable, the maximum temperature, flow rate, and stress under the PW mode are 2660 K, 0.34 m/s, and 354 MPa, respectively, which are smaller than those under the CW mode. The four solute distributions at stable temperature are as follows: The minimum mass fractions of Fe and Mn are 87% and 0.49% in the CW mode, and the maximum mass fractions of Cr and Ni are 11% and 5%. In the PW mode, the minimum mass fractions of Fe and Mn are 82% and 0.44%, and the maximum mass fractions of Cr and Ni are 14% and 5%. PW has a smaller heat input than CW, resulting in a smaller molten pool, so the elements in the molten pool are more fully mixed with other alloying elements. Metallographic experiments were performed using a scanning electron microscope to examine the mechanical properties on the fusion cladding layer, and the accuracy of the model was verified by combining numerical simulations with experimental studies for comparative analysis. [ABSTRACT FROM AUTHOR]

Hydrogen-powered polymer electrolyte membrane fuel cells (PEMFCs) show promising potential to power a wide range of mobile and stationary applications and to reduce greenhouse gas emissions significantly. In PEMFCs, the oxygen transport and the water transport are essential for a long lifetime and high-performance characteristics. The diffusion media (DM), located between the bipolar plate and the catalyst-coated membrane, is a crucial component of the fuel cell that significantly affects the cell-internal processes. Usually, the DM is a two-layer material system consisting of a microporous layer based on carbon black particles coated onto a porous gas diffusion layer (e.g., carbon paper). The properties of the microporous layer regarding the water transport at high current densities and, consequently, the fuel cell's performance and lifetime can be improved by laser structuring. Within this work, different microporous layers with varying binder content and porosities were structured by locally ablating the material using ultrashort-pulsed laser radiation in the infrared wavelength range. The effect of varying process parameters was additionally investigated. Furthermore, the ablation efficiencies were calculated for increasing pulse repetition rates to qualify a process window for an industrial structuring process. The size of the micro-drillings and the heat-affected zone surrounding the hole were evaluated through topographic and microstructure analyses using a laser scanning microscope and a scanning electron microscope with energy-dispersive x-ray spectroscopy. The results showed a rather small influence of the porosity and composition of the microporous layer on the ablation behavior. In contrast, the laser structuring parameters influenced the micro-drilling geometry significantly. [ABSTRACT FROM AUTHOR]

Measurements of transport phenomena are constantly plagued by contact resistance, prohibiting the sample's intrinsic electrical or thermal conductivity from being accurately determined. This predicament is particularly severe in thermal transport measurements due to the inability to meet similar impedance requirements for a four-probe method used in electrical resistance measurements. Here, we invent a three-probe measurement method that makes an accurate determination of thermal conductivity possible for nanomaterials. Incorporating electron beam heating provided by a scanning electron microscope (SEM) on a diffusive thermal conductor not only quantifies the thermal contact resistance, which may introduce an error of more than 270% to a sample's thermal conductivity, but also eliminates several device uncertainties that may contribute an additional 17% error in a measurement. The method also enables local temperature measurements, revealing nanoscale structural variations unfound by SEM. The high accuracy of the technique would make standardization of nanoscale thermal transport measurement possible. [ABSTRACT FROM AUTHOR]

Lead-free antiferroelectric AgNbO3 ceramics have garnered extensive attention due to their rapid charge/discharge capabilities and environmentally friendly nature, holding immense potential for energy storage applications. However, the practical utilization of AgNbO3 has been hindered by its low energy storage density. This study employed an A/B-site co-doping strategy, which yielded positive effects on the energy performance of AgNbO3 ceramics. By modifying the A/B-sites with equivalent amounts of Bi3+ and Y3+ ions, enhanced maximum polarization, improved breakdown field, and slimmer hysteresis loops were simultaneously achieved, as the combined effects of refined grain size, wider optical bandgap, and randomly distributed antiferroelectric nanodomains, which were verified through the scanning electron microscope, transmission electron microscope, and ultraviolet–visible spectrum. As a consequence, a high energy storage density of 5.40 J/cm3 accompanied by an energy storage efficiency of 56.5% was achieved in the Ag0.97Bi0.01Nb0.994Y0.01O3 ceramic under a relatively low electric field of 190 kV/cm. This study underscores the effectiveness of A/B-site aliovalent co-doping as a viable strategy for developing high-performance ceramic capacitors for energy storage applications. [ABSTRACT FROM AUTHOR]

The primary goal of this study is to examine the impact of sodium hydroxide (NaOH)/alkali-activated fly ash on the fresh properties and mechanical properties of self-compacting concrete (SCC). The fresh properties, known as the workability of SCC characteristics, were determined using the U-box, V-funnel, J-ring, and L-box tests. The M30 grade SCC containing superplasticizer of 0.86 wt. % of cement is replaced with 10%, 15%, 20%, 25%, 30%, and 40% of alkali-activated fly ash. On days 7, 14, and 28 after curing, the compressive strength and the splitting tensile strength of the SCC were examined. The study was further extended to evaluate the behavior of reinforced concrete beams containing fly ash and ground granulated blast furnace slag, whose size was 1200 × 100 × 150 mm3, under flexure loading. Based on the test results, it was found that the increase in the replacement of cement with alkali-activated fly ash increased the workability in the SCC. With the addition of superplasticizers, the SCC gained much more workability than conventional concrete containing no superplasticizer. The mechanical properties of 10% and 15% activated fly ash in Portland cement provided the maximum strength for the SCC at different ages of curing. The maximum first crack load and maximum ultimate flexure loading of the reinforced concrete beam containing 10% activated fly ash by weight of cement were greater than those of the control concrete beam. The microstructural scanning electron microscope observations confirmed that the alkali-activated fly ash increased the strength properties of the self-compacting concrete. [ABSTRACT FROM AUTHOR]

The use of aluminum alloys in automobiles is expanding, and the potential for additional increases is significant. Further growth will be determined by improvements in material qualities for existing applications or the discovery of new applications. Alloy A-356 (LM25) is commonly employed for high-quality alloy wheel rims in various motor vehicles, constituting 40% of global car usage. This study introduces 0.2% Cu into the Al–Si–Mg alloy system to enhance the mechanical properties. The alloy blend is cast into a metal mold, subjected to a 4-h cure at 540 °C, quenched with water, and precipitation hardened for 12 h at 1800 °C. Optical and scanning electron microscopes are utilized to analyze the alkali microstructure. The mechanical properties of alloyed and unalloyed castings, including hardness and tensile test results, are examined in untreated and heat-treated states. Fracture surfaces of tensile specimens are scrutinized. Intermetallic compounds formed during solidification are studied using scanning electron microscopy and x-ray diffraction analysis. The tensile strength under unalloyed (LM25) and alloyed (LM25 + 0.2 wt. % Cu) conditions before and after heat treatment [(72, 165.4 and 88.3, 237.1) and (78, 179.6 and 98, 252.9, respectively)] shows a significant increase. [ABSTRACT FROM AUTHOR]

We reported here on the fabrication and characterization of a smart titanium alloy bolt based on a high-frequency piezoelectric thin-film sensor. The thin-film sensor was directly deposited on a titanium alloy bolt head with radio frequency magnetron sputtering and characterized by a scanning electron microscope and an atomic force microscope. The ultrasonic characteristics of the smart bolt, which include a pure and broad frequency spectrum peaked at 14.81 MHz, high measurement accuracy below 3%, and high repeatability free from some interference from bolt detection position change, were fully characterized. No obvious frequency shift was observed with the increase in axial preload. Based on the mono-wave method [TOF (time of flight) of longitudinal mode wave], TOF change increased linearly with preload force in the range of 0–20 kN. With the increase in temperature from 22 to 150 °C, the TOF linearly increases while the longitudinal wave velocity linearly decreases. The results indicate the prepared smart titanium alloy bolt is suitable as a smart aviation and automotive fastener. [ABSTRACT FROM AUTHOR]

Integrating carbon nanotubes (CNTs) into a polymer matrix can significantly modify its physical properties, providing that the challenges associated with CNT dispersion are successfully resolved. In this work, we investigate the enhancement of the dielectric properties of silicone when multiwall carbon nanotubes (MWCNTs) are introduced to its polymer matrix as a filler in the frequency range from 0.5 to 20 GHz. An optimized procedure is used to prepare nanocomposites with MWCNTs concentrations by weight of 0%, 0.5%, 1.0%, 1.5%, and 2.0%. The investigated dielectric properties for the prepared nanocomposites are the real dielectric constant ɛ′, the imaginary dielectric constant ɛ″, the loss tangent tan δ, and the AC conductivity σAC. The dispersion of the MWCNTs in the silicone matrix is confirmed using the Fourier-transform infrared (FTIR) spectroscopy and the scanning electron microscope. This study shows that the dielectric properties of the nanocomposite are enhanced as the MWCNT's concentration is increased over the entire frequency range. For example, the enhancement in ɛ′ value was from 3.2 up to 21.6 at 0.5 GHz and from 2.5 to 10.6 at 20 GHz as the concentration increased from 0% to 2.0%. For the ɛ″ value, the enhancement was from less than 0.1 to 8.6 at 0.5 GHz and to 2.0 at 20 GHz, respectively. Based on the obtained tanδ values, the nanocomposites with MWCNTs of 0.5% and 1.0% can be classified as low-loss dielectrics, while the other nanocomposites with MWCNTs of 1.5% and 2.0% are classified as lossy dielectrics. [ABSTRACT FROM AUTHOR]

The damage impact of mechanical shocks on stator bar insulation is a key factor in high-voltage motor accidents. This study conducted electrical aging acceleration and breakdown experiments on damaged stator insulating materials to understand failure causes and evaluation methods. The relationship between sample defect area and depth and electrical properties was analyzed, along with the morphology of the damaged surface using a scanning electron microscope. Results show that the defect area correlates with impact mode but does not directly impact electrical performance. Effective insulation thickness is positively linked to electrical performance. This study serves as a valuable reference for evaluating mechanical impact faults in high-voltage motors. [ABSTRACT FROM AUTHOR]

By applying ultrasonic treatment to ZL205A aluminum alloy melt containing different Cd contents and then using a tensile test, a scanning electron microscope experiment, and a metallographic experiment, the influence of ultrasonic treatment to ZL205A aluminum alloy melt on the properties of aluminum–copper alloy with different Cd contents in the liquid phase high-temperature region was studied. The effect of ultrasonic treatment on the solidification structure of ZL205A aluminum alloy was investigated. The results showed that there was no significant difference in the form of Cd and the solid solution rate of the aluminum alloy with different Cd contents in ultrasonic-assisted casting. However, the effect of ultrasonic waves on the high-temperature liquid phase of the melt of ZL205A aluminum alloy can effectively reduce the porosity defects in the solidification structure of the casting, refine the solidification structure, and make the structure more uniform. The ultrasonic cavitation effect can promote the formation and uniform distribution of Al–3Ti and improve the nucleation rate, and the effect can continue after heat treatment. This can solve the problem that increasing Cd content in ZL205A greatly reduces the toughness of castings while increasing the strength. The sample with a Cd content of 0.20% and with ultrasonic treatment has the highest strength, the average tensile strength is 475.5 MPa, and the yield strength is 381.75 MPa. However, compared with the conventional casting samples with the same Cd content, the decrease in elongation was significantly reduced. [ABSTRACT FROM AUTHOR]

The changes in mechanical properties of glass fiber reinforced plastic cross-ply laminates as a result of hydrothermal aging were studied theoretically. The composite specimens have been immersed in distilled water at 25, 40, and 70 °C for 60 days for aging testing. Based on Fick's law and the Arrhenius theorem, the moisture absorption data under different environments was analyzed, and the method for determining the diffusivity and the equilibrium moisture content was obtained. The relationship model between the moisture absorption behavior of the composite material and the ambient temperature was proposed and verified by finite element analysis. The mechanical behavior of the composites was studied by tensile, compression, and three-point bending tests. Under the condition of ultimate moisture absorption, the tensile, compressive, and bending strengths of the composite decreased by 31.663%, 12.948%, and 26.985%, respectively. A variety of empirical models were used for data analysis, which confirmed the strong correlation between strength degradation and moisture absorption of composite cross-ply laminates. The scanning electron microscope observation results of different moisture absorption levels showed that matrix cracking and fiber/matrix interface debonding caused by moisture absorption are the fundamental reasons for the strength degradation of the composites. [ABSTRACT FROM AUTHOR]

With this experimental study, ZrO2/B4C/Al2O3/SiC ceramics in different weight ratios were added to 99.5% pure aluminum and composites were produced by vacuum infiltration, which is very rare in the literature. It is aimed to investigate how different ceramics will affect the technical properties of an aluminum composite. First, scanning electron microscope images were taken to examine their microstructures, and energy-dispersive x-ray spectroscopy analyses were performed. In addition, x-ray diffraction analyses of phase structures were performed. Then, the densities of the composite structures were measured. In the last stage of the experiments, hardness measurement, bending strength, and abrasive wear amount tests were carried out to determine the mechanical properties of the composite structures. According to the data obtained, a relatively homogeneous structure was obtained up to 10% of the ceramic particles in the structure. It was observed that thermal damage did not occur in the composite structures and no significant phase changes occurred. The highest infiltration distance was obtained from B4C-reinforced samples, and the lowest infiltration distances were obtained from ZrO2-reinforced samples. Ceramic reinforcement elements have reduced the density values of composite structures. With the increase in the ratio of ceramic reinforcement particles, the hardness values of the composites increased and the flexural strength values decreased. In the abrasive wear tests, the least wear loss was obtained from SiC-reinforced samples and the highest wear loss was obtained from ZrO2-reinforced samples. When the composites were evaluated according to their microstructure and mechanical strength, the best results were obtained with SiC and then Al2O3, B4C, and ZrO2 reinforcements, respectively. It has been concluded that SiC, Al2O3, B4C, and ZrO2 reinforcement elements in Al 1050-based composites produced by vacuum infiltration have a positive effect on most of the mechanical properties and a negative effect on some of them. [ABSTRACT FROM AUTHOR]

Near-stoichiometric chromium diboride films were subject to in situ annealing inside a scanning transmission electron microscope to access the thermal behavior of the film and embedded structural planar defects. Independent of films' stoichiometry, the planar defects were unaffected by the applied heat treatments. On the contrary, the interfaces between the boron-rich tissue phase and the CrB2 phase were reshaped in the overstoichometric CrB2 film. At high temperatures, diffusion of contact metal species (platinum) from the focused ion beam sample preparation was triggered, with subsequent migration onto the sample. This resulted in the formation of metal-rich regions as directly observed and characterized at the atomic level. We determined that platinum did not react with the diboride structure but is accommodated by various defects present in the film. [ABSTRACT FROM AUTHOR]

This paper presents a novel piezoelectric-driven nanoindentation system for a scanning electron microscope (SEM) with an improved analog compensation (IAC) method. This system mainly consists of a piezoelectric-driven indenter head, a rectangle-shaped transducer, and a nanopositioner module. Compared with the state-of-the-art piezoelectric-driven nanoindentation system with a circle-shaped transducer, the proposed nanoindentation system is capable of multi-direction operation inside a SEM with a rectangle-shaped transducer. Self-matched semiconductor strain gauges are selected as the position sensor for the piezoelectric-actuator. The Wheatstone bridge output voltage cannot achieve a zero temperature coefficient because the temperature coefficients of self-matched semiconductor strain gauge pairs become significantly different from each other after installation in practice. An IAC method is proposed to compensate the temperature coefficients further. Compared with the existing analog compensation method, the IAC method solves the problem of amplifier saturation and improves the sensitivity of the self-matched semiconductor strain gauge pairs position sensor by 27%. The multi-direction operation results inside a standard SEM HITACHI SU5000 validate the advantage of the developed nanoindentation system. [ABSTRACT FROM AUTHOR]

In this study, basalt fibers (BFs) and nano-silica (NS) were innovatively combined to reinforce recycled aggregate concrete (RAC) to prepare recycled aggregate concrete (named NBRAC) with better mechanical and microstructural properties as an alternative to ordinary concrete. Different NBRAC specimens were prepared by adjusting the contents of NS and BF; the damage mechanism and mechanical properties of NBRAC were investigated; and the compressive, split tensile, and flexural strengths of NBRAC were evaluated. The microstructure of NBRAC was analyzed by scanning electron microscopy observation. The results showed that the densification of NBRAC was improved under the condition of 50% RA substitution rate and that its compressive, split tensile, and flexural strengths were increased by 6.8%, 16.3%, and 32.7%, respectively, compared with that of natural concrete, which proved that the method was feasible for the preparation of high-performance RAC. Scanning electron microscope image analysis confirmed the improvement effects of NS and BF on RAC, and combined with the experimental data, a composite explanation for the improvement effects of NS and BF on RAC was proposed for the first time. [ABSTRACT FROM AUTHOR]

The use of slag-based alkali-activated concrete (AAC) could effectively address the issues of resource extraction and carbon emissions caused by traditional Portland cement. In this study, the effects of the fly ash content, water–binder ratio, and alkali activation modulus on the early mechanical properties of AAC were investigated. A total of 105 cube specimens (35 sets) were designed and subjected to compressive strength tests, scanning electron microscope tests, and x-ray diffraction composition analysis. The results indicated that excellent early strength was observed in AAC, with a compressive strength reaching ∼90% of the 28th day strength before 14 days. An increase in the fly ash content and a decrease in the water–binder ratio significantly improved the compressive strength within the same age period. The impact of a lower alkaline activation modulus on strength was found to be insignificant. Based on the experimental results, a calculation method and a constitutive model for early strength were proposed, and the theoretical values exhibited a high level of agreement with the measured values. [ABSTRACT FROM AUTHOR]

The present study focused on the environmentally friendly preparation, characterization, and certain biological activities of gold nanoparticles (Au-NPs) made with the Gundelia tournefortii (kenger) leaf extract. The results from devices such as transmission electron microscope, energy-dispersive x-ray spectrophotometer, and Fourier scanning electron microscope reveal the structures of nanoparticles. After an hour, the greatest surface plasmon resonance was discovered at 532.15 nm. The mean cubic crystallite size was calculated using the powder x-ray diffraction model and was found to be 23.53 nm. It was noted that the produced Au-NPs had spherical forms and hexagonal dimensions and ranged in size from 5 to 40 nm. The minimum inhibitory concentration and a colorimetric method for determining cell metabolic activity test, respectively, were used to investigate the suppressive effects of Au-NPs on the growth of pathogenic bacteria and healthy and cancer cell lines. [ABSTRACT FROM AUTHOR]

The fluid transport in porous media is a critical property for oil and gas exploitation, construction engineering, and environmental protection. It is profoundly influenced by pore geometry and mineral properties. Currently, the Kozeny–Carman equation serves as the permeability prediction equation for porous media, established on the circular pores model. However, it fails to fully account for the impact of pore shape and mineral properties of the soil, leading to significant deviations between predicted and measured soil permeability results. In this paper, based on scanning electron microscope image and mercury intrusion porosimetry, the pores were divided into circular pores and narrow slit pores according to the ratios of pore area and circumference. Then, the quantitative expression of the two types of pores and their connectivity and tortuosity were given, and the circular and narrow slit composite pore model was used to describe the soil pore. Subsequently, the electrostatic potential of pore water was calculated by the Poisson–Boltzmann equation to consider the adsorption effect of minerals on pore water. Combined with the Navier–Stokes equation, the permeability prediction equation considering pore geometry, pore connectivity, and tortuosity and mineral properties was established. Finally, the experimental results illustrated that the theoretical prediction results were in good agreement with the experimental results. The proposed permeability prediction equation proves valuable for assessing and predicting the fluid transport in porous media. [ABSTRACT FROM AUTHOR]

The operando hydrogen microscope is an original apparatus that has been developed to visualize the time-dependent permeation of hydrogen through a sample. This apparatus is developed based on an ultrahigh vacuum scanning electron microscope (UHV SEM). The system consists of a lens system to focus ions produced by electron-stimulated desorption (ESD), an ion detector optimized for ESD-signal detection, and a two-dimensional measurement program synchronized with the position information of the electron beam. The developed detectors and electrostatic lenses enable highly sensitive detection of the ions. In this paper, we show the details of the instrumentation of the operando hydrogen microscope. We have succeeded in recording hydrogen and deuterium flowing from the rear of metals to the surface as a series of time-lapse images, showing the time-dependent changes in the surface distribution of hydrogen and deuterium. Deuterium permeation through the metal sample was dynamically visualized at the surface by the two-dimensional mapping of the desorbed ions induced by scanning electron beam irradiation. [ABSTRACT FROM AUTHOR]

Using a scanning electron microscope, we irradiate graphene drums with electrons at an energy of 20 keV and a dosage of about 1.58 × 1017 electrons/cm2. The drums consist of graphene exfoliated in ambient air over holes having a diameter of 4.6 μm and etched into an SiO2 substrate. After irradiation, we observe that the drum's suspended monolayer (ML) region has a ratio of the Raman D peak height, ID, to the Raman G peak height, IG, as high as 6.3. In contrast, the supported ML on the SiO2 substrate has an ID/IG ratio of 0.49. Previous studies have shown that graphene drums containing air can leak in a vacuum at a low rate. We attribute the high ID/IG ratio of the suspended ML to the air that may be in the drums. We propose that the air produces much adsorbed water on the ML, resulting in a high average defect density during irradiation. We present Raman maps of the full-width-at-half maximum, position, and height of the G, 2D, D, and D' peaks before and after irradiation and maps of ID/IG and ID/ID'. We anneal the drums at temperatures from 50 to 215 °C and find that ID/IG significantly reduces to 0.42. The annealing data are analyzed using an Arrhenius plot. We also find that ID/ID' depends on annealing temperature and has values ≥8, in the range expected for sp3 defects, for ID/IG ≤ 3.9. This irradiation method may help achieve high average defect densities in ML graphene, imparting novel and potentially valuable properties. [ABSTRACT FROM AUTHOR]