Search

As a potential physical blowing agent, sodium bicarbonate (SB) is environmentally friendly and low in cost, but its low decomposition temperature cannot meet the requirements of polyolefin foam materials. Herein, for enhancing the thermal properties of SB, a modified way was offered to fabricate various SB-based capsules via suspension polymerization. As the modified SB-based capsules, epoxy resin (EP) accompanied with several organic acids was successfully coated on the surface of SB, serving as heat-insulation layer of SB. Various physicochemical characterizations provided reliable evidences for the good coating effect, and the thermal performance of the modified SB was improved. Further, the composite SB capsules were applied for the foaming of polypropylene (PP), and the foaming behavior of the SB-based capsules in PP was significantly improved, with more uniform distribution, smaller cell diameter, and higher cell density. In all, this work fully proved that the coated shells enhanced the thermal properties of SB, and the modified SB capsules significantly improved the foaming quality of foamed PP.

The current study investigates the reinforcement properties of novel nano-calcium carbonate (nano-CaCO3) synthesized from Achatina fulica snail shell. The shell was wet-milled to nanoparticle sizes using mechanochemical procedures. Epoxy nanocomposites prepared with nanofiller content ranges of 1–7 wt.% were fabricated using a conventional resin casting method. Thermal stability and degradation with mechanical properties such as tensile strength, impact strength, and the hardness properties of prepared nanocomposites were determined. It was observed that the reinforcement by the synthesized nano-CaCO3 improved the thermal stability and mechanical properties of neat epoxy irrespective of the filler content. Significantly, the inclusion of 1 w.% Achatina fulica snail shell nanoparticles increased the neat epoxy tensile strength by 75%, stiffness by over 25%, impact strength by 25%, and hardness 35%. These improved properties indicate that nano-CaCO3 synthesized from A. fulica snail shell possesses suitable reinforcement properties that can be used for nanocomposite fabrication.

International audience; New glasses based on Sb2O3-PbO association have been synthesized and characterized. The limits for glass formation have been investigated in ternary systems encompassing trivalent oxides such as Al2O3, Ga2O3, and In2O3 as the third component. Fast quenching is required to prevent melt crystallization, which results in thin samples. Chemical analysis shows a rather good agreement between nominal and analyzed compositions. Glass transition temperature, T-g, ranges between 255 degrees C and 280 degrees C, depending on composition. Density and hardness have been measured for typical samples.

A novel and excellent composite film was fabricated by simply casting cassava silk fibroin (CSF), chitosan quaternary ammonium salt (HACC), and graphene oxide (GO) in an aqueous solution. Scanning electron microscope images showed that when GO was dispersed in the composite films, the surface of CSF-based composite film became rough, and a wrinkled GO structure could be found. When the content of GO was 0.8%, the film displayed a higher change with respect to the breaking strength and elongation, respectively, up to 97.69 ± 3.69 and 79.11 ± 1.48 MPa, keeping good thermal properties because of the incorporation of GO and HACC. Furthermore, the novel CSF/HACC/GO composite film demonstrates a lower degradation rate, implying the improvement of the resistance to the enzyme solution. Especially in the film with 0.8 wt% GO, the residual mass arrived at 64.35 ± 1.1% of the primary mass after 21 days compared with the CSF/HACC film. This would reclaim the application of silk-based composite films in the biomaterial field.

This study examines the influence of cellulose nanocrystal (CN) particles on the morphological, thermal, and thermo-mechanical properties of polylactide (PLA)/poly [(butylene succinate)-co-adipate] (PBSA) blend foams prepared by casting and particulate leaching method using fructose as porogen particles. The morphological analysis showed an interconnected open-cell structure, with porosity above 80%. The crystallinity of the prepared foams was disrupted by the inclusion of CN particles as observed from XRD analyses, which showed a decrease in PLA crystal peak intensity. With regards to neat blend foam, the onset thermal degradation increased with the addition of CN particles, which also increased the thermal stability at 50% weight loss. Furthermore, CN acted as a reinforcing agent in improving the stiffness of the prepared blend foam. Overall, completely environmentally friendly foams were successfully prepared, as a potential material that can replace the current existing foam materials that pose many environmental concerns. However, there is a need to develop an environmentally friendly processing technique.

All-organic high dielectric materials are highly required in the field of modern electronic industry and energy storage. In this work, all-organic polyimide/polysulfone composite films with different amounts of PSF (PI/PSF-X) were prepared by in situ polymerization followed by film casting and thermal treatment. The dielectric, mechanical and thermal properties of these PI/PSF-X composite films are characterized by dielectric measurement, tensile test, thermogravimetric analysis and dynamic mechanical analysis. The results suggest that the PI/PSF-X composite films have good dielectric properties, good mechanical properties and excellent thermal properties, which are suitable for applications in electronic devices in harsh environments, especially in high-temperature environments.

A racemic mixture of two stereoregular polylactides (PLAs) (i.e. PLLA and PDLA) allows obtaining wholly amorphous stereocomplex PLA films by solvent casting method. The amorphous phase behavior of stereocomplex PLA is compared with that of PLLA and PDLA by advanced thermal analysis, such as Fast Scanning Calorimetry (FSC) and Dielectric Relaxation Spectroscopy (DRS). FSC allows us to quench at very high cooling rate (up to 4000 K・s–1) the studied polymers and to obtain glassy amorphous phases with high excess of enthalpy. It is shown that stereocomplexation has no influence on the glass transition temperature, the physical aging and on the cooperativity. The α and β processes were examined to study the dielectric properties, such as relaxation time, dielectric strength, and fragility. The results of FSC and DRS are correlated to determine the values of cooperativity length which are found to be similar in a wide temperature range. It is found that the studied polymers have the similar dielectric properties independently on their tacticity.

The thermal properties, emulsification, and rheological properties of exopolysaccharides (levan-BS) of Bacillus subtilis AF17 were studied and compared with those of the xanthan gum. The carbohydrate content of levan was more than 95.5% and no proteins were detected. The glass transition temperature was 31.1 °C. Levan-BS displayed a crystallization temperature of 88 °C and melting temperature was about 214 °C. Levan-BS produced more stable emulsions with olive oil and toluene, compared to xanthan gum, at an optimum concentration of 0.8%. The levan solution showed a pseudoplastic non-Newtonian fluid behavior. Levan-BS has several potential features, including high thermostability, good emulsifying properties and stability making it promising to be used in different industrial fields.

In this study, poly(vinyl alcohol) (PVA)-modified Saudi bentonite nanocomposite films were prepared using the solution method. Two surfactants, cetylpyridinium chloride and tetrabutyl phosphonium bromide, were used to modify the clay after the ion-exchange process by Na+ ions. The effect of the addition of modified Saudi bentonite (2.5%) on the thermal and flammability properties of the nanocomposite films was investigated. The prepared samples were characterized using Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Thermogravimetric analysis and differential scanning calorimetry were carried out to observe the thermal behaviour of the PVA-based nanocomposite films. Vertical flammability tests (UL94 VB) were also carried out to study the flame retardancy behaviour of the nanocomposite films. The nanocomposite films showed better flammability than pure PVA, wherein the ignition time of the nanocomposites increased and flame propagation rate decreased. The thermal stability of the nanocomposites increased by approximately 10% for the onset and endset temperature of decomposition. The type of surfactant played an important role in dispersion of the clay into the polymeric matrix and enhancing the flammability properties of the films wherein the tetrabutyl phosphonium bromide was better flame retardant than cetylpyridinium chloride.

Poly(ethylene glycol) diacrylate (PEGDA) of different molecular weights (Mn = 575 and 700) was used as crosslinking agent for the photopolymerization of 2-hydroxyethyl methacrylate (HEMA) in order to obtain HEMA/PEGDA-based hydrogels. Composites were synthesized in situ employing a new methodology that implies the addition of different quantities of silver nitrate aqueous solution to the monomer mixture with the finality to obtain hydrogels with different silver nanoparticles’ spatial density and distribution. Samples were characterized by thermal, optical, spectroscopic and structural/morphological methods. Thermal studies showed that the increase of PEGDA molecular weight and the AgNO3 concentration in the reaction mixture enhance the glass transition temperature and the thermal stability of the composites. This behavior could be related to the silver coordination with the polymer network. Infrared spectroscopy with Fourier transform and Raman analyses were realized in order to corroborate the sample chemical structure by the identification of specific functional groups. Surface hydrogel morphology was visualized with scanning electron microscopy analysis, detecting a homogeneous micro-porous surface for the samples obtained from high molecular weight PEGDA. Presence of silver nanoparticles was established by X-ray fluorescence spectroscopy and UV/Vis methods. In this last case, the characteristic silver nanoparticle plasmon was observed. Using Transmission Electron Microscopy it was possible to visualize a homogeneous spatial distribution of spherical silver nanoparticles with very narrow diameter distribution that rounds about 14–21 ± 5 nm. In general, the silver nanoparticle presence in the compounds enhances considerably their thermal/morphological characteristics. Keywords: Silver nanoparticles, HEMA/PEGDA hydrogel, Thermal properties, Crosslinking agent

Pineapple crown leaf fiber (PCLF) is one of the major biomass wastes from pineapple processing plants. It consists mostly of carbohydrate polymers, such as cellulose, hemicellulose, and lignin. It can be further processed to form a more valuable and widely used nanocrystalline cellulose (NCC). This study investigates the effect of hydrolysis time on the properties of the produced NCC. The acid hydrolysis was conducted using 1 M of sulfuric acid at hydrolysis times of 1–3 h. The resulting NCCs were then characterized by their morphology, functional groups, crystallinity, thermal stability, elemental composition, and production yield. The results show that the NCC products had a rod-like particle structure and possessed a strong cellulose crystalline structure typically found in agricultural fiber-based cellulose. The highest NCC yield was obtained at 79.37% for one hour of hydrolysis. This NCC also displayed a higher decomposition temperature of 176.98 °C. The overall findings suggest that PCLF-derived NCC has attractive properties for a variety of applications.

The present study deals with the formation of a phosphorylated polyvinyl alcohol (PPVA)-Aluminum Phosphate (AlPO4) nanocomposite, changing the pH solution under the two-step process involving the phosphorylation of polyvinyl alcohol (PVA) followed by the conjugation with AlPO4. The composite was formed by varying the pH of the solution in the range of 7–12 and the reflected changes in the product’s morphology, crystallinity, surface nature, thermal stability, etc. were recorded using FESEM, XRD, FTIR, UV-Vis spectroscopy, TGA, etc. From the analysis, it was found that the particles formed with two different sizes of the probed pH, and at pH 10 they were homogeneously distributed. In addition, the morphology of the PPVA-AlPO4 composite also seems to be altered with respect to the pH and this is due to the differences in the amount of H+ and OH− anions. Thus, from the overall analysis, it can be indicated that pH 10 needs to be maintained for the formation of a spherical shape and uniformly distributed PPVA-AlPO4 nanocomposite.

The TiO2 NPs have been successfully synthesized by sol-gel method and the SWCNTs/TiO2 nanostructures have been fabricated by a simple mixing technique. By a solution casting process, pure CMC/PEO and SWCNTs/TiO2 nanohybrid doped CMC/PEO polymer blend films have been prepared. The influence of SWCNTs/TiO2 nanohybrid loading on the thermal, optical, and conductivity properties of the polymer blend has been discussed. The XRD pattern shows that the average crystallite size of the nanoparticles for TiO2 and SWCNTs/TiO2 is 20 nm and 15 nm, respectively, and a change in crystallinity was observed with an increase in doping. The interaction between CMC/PEO chains and SWCNTs/TiO2 nanohybrid is confirmed by FTIR spectra. The optical absorption spectrum shows that the energy gap reduces with the dopant increase. The miscibility between the CMC and PEO was confirmed by DSC thermograms. With an increase in dopant content, the TGA study demonstrates that the system's thermal stability improves. The maximum value of the blend's AC conductivity is 4.77 10−6 S/m, and by increasing the loading of SWCNTs/TiO2 to 3.2 (wt%) increased to 9.23 10−4 S/m. The conduction mechanism changed with SWCNTs/TiO2 loading from the correlated barrier hopping, in the prepared samples. Usage of these nanocomposite films in the semiconductor industry is encouraged by the observed improvements in optical, thermal, and AC conductivity.

The advanced tendencies in building materials development are related to the design of cement composites with a reduced amount of Portland cement, contributing to reduced CO2 emissions, sustainable development of used non-renewal raw materials, and decreased energy consumption. This work deals with water cured for 28 and 120 days cement composites: Sample A—reference (white Portland cement + sand + water), Sample B—white Portland cement + marble powder + water, and Sample C white Portland cement + marble powder + polycarboxylate-based water reducer + water. By powder X-ray diffraction and FTIR spectroscopy, the redistribution of CO32−, SO42−, SiO44−, AlO45−, and OH− (as O-H bond in structural OH− anions and O-H bond belonging to crystal bonded water molecules) from raw minerals to newly formed minerals have been studied, and the scheme of samples hydration has been defined. By thermal analysis, the ranges of the sample’s decomposition mechanisms were distinct: dehydration, dehydroxylation, decarbonation, and desulphuration. Using mass spectroscopic analysis of evolving gases during thermal analysis, the reaction mechanism of samples thermal decomposition has been determined. These results have both practical (architecture and construction) and fundamental (study of archaeological artifacts as ancient mortars) applications.

[EN] An eco-friendly strategy for the modification of polylactic acid (PLA) surface properties, using a solvent-free process, is reported. Reactive extrusion (REX) allowed the formation of new covalent bonds between functional molecules and the PLA polymeric matrix, enhancing its mechanical properties and modifying surface hydrophobicity. To this end, the PLA backbone was modified using two alkoxysilanes, phenyltriethoxysilane and N-octyltriethoxysilane. The reactive extrusion process was carried out under mild conditions, using melting temperatures between 150 and 180 degrees C, 300 rpm as screw speed, and a feeding rate of 3 kg center dot h(-1). To complete the study, flat tapes of neat and functionalized PLA were obtained through monofilament melt extrusion to quantify the enhancement of mechanical properties and hydrophobicity. The results verified that PLA modified with 3 wt% of N-octyltriethoxysilane improves mechanical and thermal properties, reaching Young's modulus values of 4.8 GPa, and PLA hydrophobic behavior, with values of water contact angle shifting from 68.6 degrees to 82.2 degrees., This research work was funded by the Conselleria d'Economia Sostenible, Sectors Productius, Comerc i Treball de la Generalitat Valenciana through IVACE. Project references: GREENFILS, IMAMCI/2019/1 and BIOREX, IMAMCI/2020/1.

In the present study, 100% bio-based polyesters of 2,5-thiophenedicarboxylic acid were synthesized via two-stage melt polycondensation using glycols containing 3 to 6 methylene groups. The so-prepared samples were characterised from the molecular point of view and processed into free-standing thin films. Afterward, both the purified powders and the films were subjected to structural and thermal characterisation. In the case of thin films, mechanical response and barrier properties to O2 and CO2 were also evaluated. From the results obtained, it emerged that the length of glycolic sub-units is an effective tool to modulate the chain mobility and, in turn, the kind and amount of ordered phases developed in the samples. In addition to the usual amorphous and 3D crystalline phases, in all the samples investigated it was possible to evidence a further phase characterised by a lower degree of order (mesophase) than the crystalline one, whose amount is strictly related to the glycol sub-unit length. The relative fraction of all these phases is responsible for the different mechanical and barrier performances. Last, but not least, a comparison between thiophene-based homopolymers and their furan-based homologues was carried out.

Biodegradable packaging prepared from starch is an alternative to fossil-based plastic packaging. However, the properties of starch packaging do not comply with the necessary physicochemical properties to preserve food. Hence, in a previous study, we reported the preparation of a composite polymer material based on starch-chitosan-pluronic F127 that was found to be an adequate alternative packaging material. In this study, we modified the physicochemical properties of this material by storing it for 16 months under ambient conditions. The results indicate that the incorporation of pluronic F127 in the blend polymer can help avoid the retrogradation of starch. Moreover, at higher concentrations of pluronic F127, wettability is reduced. Finally, after storage, the materials exhibited surface modification, which is related to a color change and an increase in solubility, as well as a slight increase in stiffness.

Over the last few decades, bio-based polymers have attracted considerable attention from both academic and industrial fields regarding the minimization of the environmental impact arising from the excessive use of petrochemically-based polymeric materials. In this context, poly(ethylene vanillate) (PEV), an alipharomatic polyester prepared from 4-(2-hydroxyethoxy)-3-methoxybenzoic acid, a monomer originating from lignin-derived vanillic acid, has shown promising thermal and mechanical properties. Herein, the effects of three different catalysts, namely titanium butoxide (TBT), titanium isopropoxide (TIS), and antimony trioxide (Sb2O3), on the synthesis of PEV via a two-stage melt polycondensation method are investigated. The progress of the reaction is assessed using various complementary techniques, such as intrinsic viscosity measurement (IV), end group analysis (AV), nuclear magnetic resonance spectroscopy (NMR), Fourier-transformed infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC). The thermal stability of the produced polyesters is studied by evolved gas analysis mass spectrometry (EGA-MS). Moreover, as the discoloration in polymers affects their applications, color measurement is performed here. Finally, theoretical kinetic studies are carried out to rationalize the experimental observations.

This work investigates the effects of modification of polylactide (PLA) using dicumyl peroxide (DCP) as a crosslinker and Joncryl as a chain extender on boehmite distribution. The PLA/boehmite (PLA/BA) composites at various concentrations were prepared via a twin-screw extruder. Transmission electron microscopy showed more agglomerations of BA particles when Joncryl and DCP were added individually to the PLA matrix, with lesser agglomeration upon simultaneous addition of DCP and Joncryl, which led to an enhancement of 10.7% of the heat distortion temperature and 8.8% of the modulus. The existence of fine dispersed BA particles in the BA3 sample improved the cold crystallization by 4 °C. Moreover, the maximum reinforcing effect in increasing the storage modulus of the prepared system was observed upon concurrent addition of DCP and Joncryl, with minimum reinforcing effect upon individual addition of DCP and Joncryl. In general, a bio-based PLA composite base BA with enhanced properties was successfully prepared for various applications.

Lyocell fabrics are widely applied in textiles, however, its high flammability increases the risk of fire. Therefore, to resolve the issue, a novel biomass-based flame retardant with phosphorus and nitrogen elements was designed and synthesized by the reaction of arginine with phosphoric acid and urea. It was then grafted onto the lyocell fabric by a dip-dry-cure technique to prepare durable flame-retardant lyocell fabric (FR-lyocell). X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FTIR) analysis demonstrated that the flame retardant was successfully introduced into the lyocell sample. Thermogravimetric (TG) and Raman analyses confirmed that the modified lyocell fabric featured excellent thermal stability and significantly increased char residue. Vertical combustion results indicated that FR-lyocell before and after washing formed a complete and dense char layer. Thermogravimetric Fourier-transform infrared (TG-FTIR) analysis suggested that incombustible substances (such as H2O and CO2) were produced and played a significant fire retarding role in the gas phase. The cone calorimeter test corroborated that the peak of heat release rate (PHRR) and total heat release (THR) declined by 89.4% and 56.4%, respectively. These results indicated that the flame retardancy of the lyocell fabric was observably ameliorated.

Polyurethane (PU) is one of the principal polymers in the global plastic market thanks to its versatility and continuous improvement. In this work, PU elastomeric materials having thermoregulating properties through the incorporation of microcapsules (mSD-(LDPE·EVA-RT27)) from low-density polyethylene and vinyl acetate containing paraffin®RT27 as PCM were produced. Elastomers were synthesized while varying the molar ratio [NCO]/[OH] between 1.05 and 1.1 and the microcapsule (MC) content from 0.0 to 20.0 wt.%. The successful synthesis of the PUs was confirmed by IR analyses. All the synthesized elastomers presented a structure formed by a net of spherical microparticles and with a minimum particle size for those with 10 wt.% MC. The density and tensile strength decreased with the MC content, probably due to worse distribution into the matrix. Elastomer E-1.05 exhibited better structural and stability properties for MC contents up to 15 wt.%, whereas E-1.1, containing 20 wt.% MC, revealed mechanical and thermal synergy effects, demonstrating good structural stability and the largest latent heat. Hence, elastomers having a large latent heat (8.7 J/g) can be produced by using a molar ratio [NCO]/[OH] of 1.1 and containing 20 wt.% mSD-(LDPE·EVA-RT27).

A technique for the fabrication of bacterial cellulose-based films with CeO2 nanofiller has been developed. The structural and morphological characteristics of the materials have been studied, their thermal and mechanical properties in dry and swollen states having been determined. The preparation methodology makes it possible to obtain composites with a uniform distribution of nanoparticles. The catalytic effect of ceria, regarding the thermal oxidative destruction of cellulose, has been confirmed by TGA and DTA methods. An increase in CeO2 content led to an increase in the elastic modulus (a 1.27-fold increase caused by the introduction of 5 wt.% of the nanofiller into the polymer) and strength of the films. This effect is explained by the formation of additional links between polymer macro-chains via the nanoparticles’ surface. The materials fabricated were characterized by a limited ability to swell in water. Swelling caused a 20- to 30-fold reduction in the stiffness of the material, the mechanical properties of the films in a swollen state remaining germane to their practical use. The application of the composite films in cell engineering as substrates for the stem cells’ proliferation has been studied. The increase in CeO2 content in the films enhanced the proliferative activity of embryonic mouse stem cells. The cells cultured on the scaffold containing 5 wt.% of ceria demonstrated increased cell survival and migration activity. An analysis of gene expression confirmed improved cultivation conditions on CeO2-containing scaffolds.

Poly(vinyl alcohol) nanofibrous mats containing ad hoc synthesized gold nanostructures were prepared via a single-step electrospinning procedure and investigated as a novel composite platform with several potential applications. Specifically, the effect of differently shaped and sized gold nanostructures on the resulting mat physical-chemical properties was investigated. In detail, nearly spherical nanoparticles and nanorods were first synthesized through a chemical reduction of gold precursors in water by using (hexadecyl)trimethylammonium bromide as the stabilizing agent. These nanostructures were then dispersed in poly(vinyl alcohol) aqueous solutions to prepare nanofibrous mats, which were then stabilized via a humble thermal treatment able to enhance their thermal stability and water resistance. Remarkably, the nanostructure type was proven to influence the mesh morphology, with the small spherical nanoparticles and the large nanorods leading to thinner well defined or bigger defect-rich nanofibers, respectively. Finally, the good mechanical properties shown by the prepared composite mats suggest their ease of handleability thereby opening new perspective applications.

Made available in DSpace on 2021-06-25T10:37:13Z (GMT). No. of bitstreams: 0 Previous issue date: 2021-05-01 Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) For suitable design of equipment and process optimization, the determination of thermophysical properties of the raw materials is necessary. Therefore, this work was aimed at determining and modeling the density, specific heat, thermal diffusivity, and thermal conductivity of acid slurries of cassava bagasse used during its conversion into bioethanol. Experimental measurements were carried out in slurries with different mass fractions of cassava bagasse (0.00 to 0.10) and phosphoric acid (0.00 to 0.10) at temperatures from 278.13 to 318.13 K. Results obtained show that density varied from 986.5 to 1,029.3 kg∙m−3, specific heat from 3,830.0 to 4,142.6 J∙kg−1∙K−1, thermal diffusivity from 0.9624 × 10−7 to 1.5249 × 10−7 m2∙s−1 and thermal conductivity from 0.3825 to 0.6212 W∙m−1∙K−1. While density increased with increasing solids and acid content at decreasing temperature, the thermal properties decreased at higher solids and acid content and increased when heating the slurries. The values were well-fitted to polynomial models with good accuracy (R2 > 0.921 and MRE < 1.75%), allowing the application of the models to obtain reliable and ready-to-use data for cassava bagasse processing. Thus, the data reported in this study can be used for designing and managing momentum, heat and mass transfer processes for enhancing bioethanol production from cassava bagasse. Food Engineering and Technology Department São Paulo State University (Unesp) Institute of Biosciences Humanities and Exact Sciences (Ibilce) Group of Analysis and Simulation of Agro-food Processes Food Technology Department Universitat Politècnica de València (UPV) Food Engineering and Technology Department São Paulo State University (Unesp) Institute of Biosciences Humanities and Exact Sciences (Ibilce) FAPESP: 2017/06518-2 CAPES: 88881.132626/2016-01 CAPES: Code 001

In this study, the effect of aspect ratio of graphene oxide (GO) on the properties of poly (vinyl alcohol) (PVA) nanocomposites were investigated. The PVA/GO nanocomposites were prepared by a simple solution casting method. GO with 3 different lateral sizes, 0.5, 1.5 and 3 µm were used. The higher the aspect ratio, the higher the Young's modulus obtained. The effect of aspect ratio on Young's modulus was in agreement with the Halpin-Tsai model, especially when GO was highly aligned in uniaxially drawn nanocomposites. Similar to the Young's modulus, the barrier properties increased with increasing GO aspect ratio. On the other hand, the highest glass transition temperature as well as the highest thermal decomposition temperature was achieved for the GO of the lowest aspect ratio.