Search

Global regulations are guiding society towards more sustainable material solutions. This increasing awareness of the need for environmentally friendly alternatives has led to a greater emphasis on biocomposites, which combine natural fibers with bio-based polymers. This study investigates how bleached softwood pulp fibers (BSWPF) and unbleached softwood pulp fibers (UBSWPF) affect the characteristics of poly(lactic acid) (PLA)-based biocomposites. UBSWPF is a more cost-effective option because it is manufactured with less processing steps than BSWPF. However, it is largely unexplored as a reinforcement in biopolymers. Through investigating the mechanical, thermal, and morphological aspects of the biocomposites, this study showed that UBSWP increased the modulus and impact strength of the PLA biocomposites better than BSWPF. The impact strength, modulus, and tensile strength of PLA-BSWPF and PLA-UBSWPF improved as the fiber content increased. However, a decrease in tensile strength was seen at higher percentages of UBSWPF in PLA. Despite the decrease in tensile strength at higher UBSWPF concentrations, both types of fibers improved the mechanical properties of the biocomposites, demonstrating a potential sustainable reinforcing material for PLA biocomposites. [ABSTRACT FROM AUTHOR]

The canola oil industry generates significant waste as canola meal (CM) which has limited scope and applications. This study demonstrates the possibility of valorization of CM as a sustainable natural filler in a biodegradable polymer composite of Poly(lactic acid) (PLA). Generally, interfacial bonding between natural fibers and the polymer matrix in the composite is weak and non-uniform. One possible solution is to derivatize natural fibre to introduce interfacial bond strength and compatibility with the PLA polymer matrix. Here, CM was succinylated in a reactive extrusion process using succinic anhydride at 30 wt% to get 14% derivatization with 0.02 g of -COOH density per g of CM. The CM or succinylated CM at 5 and 15 wt% was co-extruded with amorphous PLA to get composite fibers. CM-PLA and succinylated CM-PLA biocomposites were foamed using a mild and green microcellular foaming process, with CO2 as an impregnating agent without any addition of organic solvents. The properties of the foams were analyzed using differential scanning calorimetry (DSC), Dynamic mechanical thermal analysis (DMTA), shrinkage, and imaging. The addition of CM or succinylated CM as a natural filler did not significantly change the glass transition temperature, melting point, percent crystallization, stiffness, and thermal stability of PLA foams. This suggests succinylation (modification) of CM is not a mandatory step for improving interphase compatibility with the amorphous PLA. The new PLA-CM foams can be a good alternative in the packaging industry replacing the existing petroleum-based polymer foams. Highlights: Valorization of CM as a sustainable natural filler in PLA biocomposite foams Modification of CM is not mandatory for interphase compatibility with the PLA PLA-CM foams have similar appearance and properties to control PLA foams New PLA-CM foams can be a good alternative in the packaging industry [ABSTRACT FROM AUTHOR]

The fiber-filled polymer composite is one of the best materials which provides a symmetrical superior strength and stiffness to structures. With the strengthening of people's environmental protection and resource reuse consciousness, the development of renewable materials, especially natural fiber-filled polymer composites, is receiving great attention. This study investigated the mechanical properties of polymer composites incorporating waste materials from the food processing industry and agricultural sources. Waste vegetal fiber-filled polymer biocomposites (WVFFPBs) with varying fiber types and 3D printing orientations were systematically fabricated. Subsequently, the tensile tests were executed to comprehensively assess the anisotropic mechanical behaviors of the WVFFPBs. The results demonstrated that WVFFPBs performed excellent anisotropic mechanical properties compared to pristine matrix samples as print orientation changed. As the printing angle increased from 0° to 90°, the tensile mechanical properties of the WVFFPBs displayed a decreasing trend. Moreover, the print orientation–anisotropic mechanical behavior relationship of 3D-printed WVFFPBs was revealed through the analysis of the material manufacturing characteristics and damage features. [ABSTRACT FROM AUTHOR]

Disposable surgical gowns are usually made from petroleum-based synthetic fibers that do not naturally decompose, impacting the environment. A promising approach to diminish the environmental impact of disposable gowns involves utilizing natural fibers and/or bio-based synthetic fibers. In this study, composite webs from polylactic acid (PLA) bicomponent fiber and natural fibers, cattail and kapok fibers, were prepared using the hot press method. Only the sheath region of the PLA bicomponent fiber melted, acting as an adhesive that enhanced the strength and reduced the thickness of the composite web compared with its state before hot pressing. The mechanical and physical properties of these composite webs were evaluated. Composite webs created from kapok fibers displayed a creamy yellowish-white color, while those made from cattail fibers showed a light yellowish-brown color. Additionally, the addition of natural fibers endowed the composite webs with hydrophobic properties. The maximum natural fiber content, at a ratio of 30:70 (natural fiber to PLA fiber), can be incorporated while maintaining proper water vapor permeability and mechanical properties. This nonwoven material presents an alternative with the potential to replace petroleum-based surgical gowns. [ABSTRACT FROM AUTHOR]

Natural fibers are one of the most attractive materials in biocomposites due to their potential for sustainability. This study aims to prepare sustainable composite materials using fibers from Sansevieria trifasciata (snake plant) and to investigate their mechanical, morphological, and water absorption properties. The composite was prepared with epoxy resin through a manual hand lay‐up process, maintaining standard parameters with changeable reinforcement (10%, 20%, and 30%). The mechanical properties (tensile, impact, and flexural strength), Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), and water absorbency of the composites were evaluated. The result showed that the tensile strength, flexural strength, and impact resistance of the composites are 6.99 MPa, 10.77 MPa, and 14 J, respectively, for 30% fiber components, which are significantly higher than other composite materials. The SEM analysis showed a strong interfacial bond between the snake plant fiber and the epoxy resin. The FTIR analysis revealed a reduction in hemicellulose and lignin and an improvement in the interfacial adhesion between snake plant fiber and epoxy resin. The composites also demonstrated time‐dependent increases in water absorption, with the sample containing 30% fiber components showing the best absorbency performance at 0.88%. Highlights: A study is being conducted on the effective and sustainable use of biowaste.The composite materials loaded with 30% fibers had significantly high tensile strength, flexural strength, and impact resistance.The SEM analysis of snake plant fiber‐reinforced polymer composite showed a strong interfacial bond between fiber and epoxy resin.The FTIR analysis of the composite revealed the reduction of hemicellulose and lignin.The use of non‐renewable materials is reduced, and eco‐friendliness is promoted. [ABSTRACT FROM AUTHOR]

Abstract This study involved fabricating thermoplastic wheat starch–sugarcane bagasse biocomposites through melt mixing method. The effect of sugarcane bagasse concentration at 3 levels of 0 wt.%, 7.5 wt.% and 15 wt.% of wheat starch and sorbitol:glycerol weight ratio at 4 levels of 0:4, 1:4, 2:4 and 4:4 on their physicomechanical properties was evaluated. The results indicated that increasing both of the weight ratio of sorbitol to glycerol and the concentration of bagasse generally led to a significant increase in tensile strength and modulus, but a decrease in elongation at break and equilibrium moisture content. The biocomposite containing the weight ratio of sorbitol:glycerol of 0:4 and bagasse concentration of zero, had the lowest tensile strength (0.22 MPa) and tensile modulus (0.23 MPa), and the highest elongation at break (103.1%) and equilibrium moisture content (30.6%) and conversely The biocomposite containing the weight ratio of sorbitol:glycerol of 4:4 and bagasse concentration of 15, had the highest tensile strength (5.3 MPa) and tensile modulus (371.5 MPa), and the lowest elongation at break (1.5%) and equilibrium moisture content (20.6%). Moisture absorption was also studied using the Peleg model, which showed that samples with lower weight ratios of sorbitol to glycerol and lower bagasse concentrations had higher initial moisture absorption rates and greater moisture absorption capacity. The investigation of thermal behavior of the biocomposites by TGA analysis showed improved thermal stability of the biocomposites by increasing both of the sorbitol:glycerol weight ratio and the bagasse concentration. Finally, the FTIR spectrum revealed an increase in hydrogen and polar bonds in the biocomposites compared to pure starch. Graphical Abstract

This study involved fabricating thermoplastic wheat starch–sugarcane bagasse biocomposites through melt mixing method. The effect of sugarcane bagasse concentration at 3 levels of 0 wt.%, 7.5 wt.% and 15 wt.% of wheat starch and sorbitol:glycerol weight ratio at 4 levels of 0:4, 1:4, 2:4 and 4:4 on their physicomechanical properties was evaluated. The results indicated that increasing both of the weight ratio of sorbitol to glycerol and the concentration of bagasse generally led to a significant increase in tensile strength and modulus, but a decrease in elongation at break and equilibrium moisture content. The biocomposite containing the weight ratio of sorbitol:glycerol of 0:4 and bagasse concentration of zero, had the lowest tensile strength (0.22 MPa) and tensile modulus (0.23 MPa), and the highest elongation at break (103.1%) and equilibrium moisture content (30.6%) and conversely The biocomposite containing the weight ratio of sorbitol:glycerol of 4:4 and bagasse concentration of 15, had the highest tensile strength (5.3 MPa) and tensile modulus (371.5 MPa), and the lowest elongation at break (1.5%) and equilibrium moisture content (20.6%). Moisture absorption was also studied using the Peleg model, which showed that samples with lower weight ratios of sorbitol to glycerol and lower bagasse concentrations had higher initial moisture absorption rates and greater moisture absorption capacity. The investigation of thermal behavior of the biocomposites by TGA analysis showed improved thermal stability of the biocomposites by increasing both of the sorbitol:glycerol weight ratio and the bagasse concentration. Finally, the FTIR spectrum revealed an increase in hydrogen and polar bonds in the biocomposites compared to pure starch. [ABSTRACT FROM AUTHOR]

In this study, we utilized a hybridization approach for two different fibers to overcome the drawbacks of single-fiber-reinforced PLA composites. Coir fiber and bamboo leaf fiber were used as reinforcing natural fibers as their properties complement one another. Additionally, we combined thermal annealing with hybridization techniques to further improve the overall properties of the composites. The results showed that the hybridization of BF: CF with a ratio of 1:2 gave PLA-based hybrid composites optimal mechanical and thermal properties. Furthermore, the improvement in the thermal stability of hybrid composites, attributable to an increase in crystallinity, was a result of thermal annealing. The improvement in HDT in annealed 1BF:2CF hybrid composite was about 13.76% higher than that of the neat PLA. Annealing of the composites led to increased crystallinity, which was confirmed using differential scanning calorimetry (DSC). The synergistic effect of hybridization and annealing, leading to the improvement in the thermal properties, opened up the possibilities for the use of PLA-based composites. In this study, we demonstrated that a combined technique can be utilized as a strategy for improving the properties of 100% biocomposites and help overcome some limitations of the use of PLA in many applications. [ABSTRACT FROM AUTHOR]

Bioderived poly(lactic acid) (PLA) is a promising alternative for fossilbased polymers, but its poor hydrophilicity, high brittleness, and low heatresistance are problems for its utilization. In this work, bleached softwood kraft pulp (BSKP) fiber was adopted to modify PLA with MAPP as the coupling agent, with BSKP accounting for 10 wt% to 50 wt%. Internal mixing (IM) was applied to mix the PLA/fiber blend instead of screw grinding. The thermal and mechanical properties of the composites were assessed. The IM process was proven qualified for its effective dispersion of BSKP fibers in the PLA matrix. At a fiber loading of 50 wt%, IMprocessed composites acquired satisfactory tensile strength (50.49 MPa, slightly higher than PLA) and Young's modulus (2.56 GPa, 45.8% higher than PLA). The pulp fillers matched PLA matrix well for the characteristic temperatures in thermal decomposition. The BSKP/PLA composites were thermally strengthened by pulp fibers characterized by higher content of residues. The fibers improved the interfacial crystallinity of PLA in the composites (i.e., from 5.22% to 11.86%). The increased crystallinity resulted in enhanced stiffness or weaker damping performance of the composites. In conclusion, natural plant fibers are a feasible option to modify PLA for extended applications. [ABSTRACT FROM AUTHOR]

The usage of new cellulosic fibers in industrial applications is massive because of its excellent performances. These fibers are utilized especially for manufacture of high-performance composites. Coconut leaf sheath (CLS) fibers are extracted for leaf sheath of coconut tree. The aim of this paper is to study the possibility of using a natural fiber CLS as an alternative for polymer composites. In the current study, the consequence of NaOH treatment on structural, thermal and morphological behavior of treated and untreated coconut leaf sheath (CLS) fiber in terms of single fiber tensile strength, Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (×RD), ther)mogravimetric analysis (TGA) and differential scanning calorimeter (DSC) has been explored. From SEM analysis, it was identified globular lumps spread consistently over the fiber which could help the mechanical interlock with the resin. The outcomes from the experimentation exposed that the NaOH treatment has impacted in the eradication of amorphous hemicellulose and lignin contents from the CLS fiber surface and in turn resulted in excellent structural and thermal stability behaviour of fiber. The present work endorses the great potential of CLS fibers to be utilized for bio-reinforcement in order to fabricate lightweight composite structures, employed in automobile and structural applications. [ABSTRACT FROM AUTHOR]

A new class of biobased composites with tailorable mechanical properties made of natural fibers, polylactic acid, and ferulic acid derivatives (FAD) is studied. FAD was used to develop composites with elastomeric properties like improved elongation at break and highly reversible deformation upon elongation. Composites were prepared using raw and enzymatically treated hemp fibers. The fibers were defibrillated due to the enzymatic treatment increasing their aspect ratio. The composites were characterized by their mechanical properties and their reaction to fire. No significant change in the dispersion of the fibers in the composites was reported. Homogenously dispersed crystallites of FAD were observed by scanning electron microscopy in the PLA matrix and at the interface between the PLA and the fibers, where they are suspected to increase the free volume in correlation with a decrease in mechanical properties following the increase in the aspect ratio of the fibers. FAD also degraded the reaction to fire of the material with an increase in 10% of the peak of Heat Release Rate (pHRR) in comparison to neat PLA. It also increased the charring residue up to 3 wt.%. A synergistic effect between FAD and the lignin increasing the charring residue is also reported. [ABSTRACT FROM AUTHOR]

A series of eco-friendly biocomposites with improved mechanical properties and interfacial interaction were prepared by melt-mixing natural fibers using a cellulose acetate derivative as a polymer matrix and used to evaluate their mechanical, thermal, and morphological properties. The natural fiber used as a biofiller was pre-surface-treated by a refining process using alkali and natural enzymes to improve compatibility and increase interfacial bonding with biopolymer substrate. To increase the processability of the cellulose material, the raw material was plasticized and the composition prepared in the form of pellets in a twin-screw extruder by mixing with an additive before being molded through an injection process. For each composition, the interfacial bonding force between different materials was confirmed through morphology analysis and evaluation of mechanical and thermal properties. When biofillers and a viscosity modifier were used at the same time, the fabricated biocomposites had controllable crystallinity, stiffness, and elasticity and showed improved mechanical strength, such as tensile strength and flexural strength. These results indicated that interfacial properties could be increased through interfacial interactions between two different components due to appropriate surface treatment. In addition, it was confirmed that a composition having interfacial interaction, not a simple mixture, could be prepared by lowering both glass transition and melting temperature. The lowering of glass transition temperature increased the elasticity of the biocomposites, which have the potential advantage of easier melt processing when applied to various injection parts. [ABSTRACT FROM AUTHOR]

In engineering applications, natural fiber composites must comply with fire requirements including the use of flame retardant. Furthermore, biocomposites are known to be water sensitive. Whether flame retardants affect the water sensitivity and whether water absorption affects the fire behavior and the mechanical performance of biocomposites are the two main topics addressed in this work. In this study, a flax fiber/epoxy composite flame retardant with 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) or aluminum diethyl phosphinate (AlPi) was aged in humid atmosphere or by immersion in water. Water absorption kinetics revealed that DOPO induces an increase in equilibrium water content by approximately a factor of 2 due to its intrinsic hygroscopicity and/or its plasticizing effect on the epoxy matrix. In contrast, AlPi does not significantly change the water sensitivity of the biocomposite. Mechanical testing highlighted that, whatever the FR, the evolution of mechanical properties with ageing is governed by the moisture content. The drop of elastic modulus was attributed to a decrease in fiber rigidity due to plasticization, while the increase in tensile strength was assigned to an increase in fiber/matrix friction due to fiber swelling. As regards flame retardancy, only the highest water contents modified the fire behavior. For the AlPi containing biocomposite, the water release resulted in an increase by 50% of the time to ignition, while for the DOPO flame retardant biocomposite the water release was mainly postponed after ignition. [ABSTRACT FROM AUTHOR]

Natural fibre biopolymer composites with both fibres and matrix being derived from biomaterials are increasingly used in demanding applications, such as sensing, packaging, building, and transport, and require good electrical, thermal, and flame retardant properties. Herein, an investigation of the effectiveness of functionalising nonwoven cotton/poly(lactic acid) (PLA) fibre mats with graphene oxide nanosheets has been reported by using a facile dip-coating method followed by thermal reduction for enhancing the electric, thermal, and abrasion-resistance properties. The manufacturing processes for preparing biocomposites and introducing functionality are readily scalable. Experimental results reveal that with the addition of less than 0.5 wt% graphene nanoplatelets, the biocomposites showed significant improvements in abrasion resistance, electrical conductivity, thermal conductivity, and diffusivity. Furthermore, the composite shows excellent piezo-resistivity to act as strain sensors with a gauge factor of 2.59 at strains up to 1%. [ABSTRACT FROM AUTHOR]

Fiber-reinforced green composites made from natural plant fibers are an increasingly popular sustainable alternative to conventional high-performance composite materials. Given the variety of natural fibers themselves, and the even larger variety of possible composites with specific fiber dosage, fiber orientation distribution, fiber length distribution, and fiber–matrix bond characteristics, micromechanics-based modeling is essential for characterizing the macroscopic response of these composites. Herein, an analytical multiscale micromechanics model for elastic homogenization is developed, capable of capturing the variety. The model features (i) a nanoscopic representation of the natural fibers to predict the fiber stiffness from the universal stiffness of the fiber constituents, mainly cellulose, (ii) a spring-interface model to quantify the compliance of the fiber–matrix bond, and (iii) the ability to model any (and any combination of) orientation distribution and aspect ratio distribution. Validation is performed by comparing the predicted stiffness to experimental results for as many as 73 composites available in the literature. Extensive sensitivity analyses quantify the composite stiffening upon increasing fiber volume fraction, fiber alignment, fiber length, and fiber–matrix interface stiffness, respectively. [ABSTRACT FROM AUTHOR]

Paunch is a fibrous solid residue consisting of partially digested feed from the stomachs of processed cattle. It is the largest untapped solid waste stream from animals at meat processing plants, and potentially a valuable source of fibres for the production of sustainable and potentially higher-value natural biocomposite materials. Paunch was obtained from the waste effluent of a red meat processing plant, and the fibre characteristics of the as-obtained material were studied and benchmarked against wood flour and ground buffel grass, with a view to evaluating the potential of paunch as a fibre for polymer composites. The ground paunch possessed a rough fibrous surface and fibre-like characteristics that were comparable to both wood flour and ground buffel grass, demonstrating their potential for use in composites. Without any pre-treatment or compatibilisation, composites of a representative biopolymer, poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and ground paunch were successfully produced for the first time via extrusion, with up to 50 wt% paunch content. Mechanical property analysis showed that, at 30 wt% content, PHBV/ground paunch composites yielded mechanical properties that were comparable to those of composites with ground buffel grass. [ABSTRACT FROM AUTHOR]

Natural fibers such as jute, cotton, and bamboo composites are becoming alternative materials to synthetic fiber composites, as their use raises awareness of environmental protection. Among natural fibers, jute and cotton fibers were used in this research to fabricate six-layered composites reinforced by spent tea leaves. Varying amounts (0, 5, 10, and 15 g) of spent tea leaf powder were incorporated as reinforcement with resin to improve and observe properties and determine usability. The prepared composites were investigated comparatively in terms of mechanical, microstructural, morphological, and thermal properties. As regards mechanical characterization, tensile, compression, and bending properties were tested in this research to compare the obtained data with the data available in the literature to show its practical application. The results indicated that significant improvements in mechanical properties were obtained from the composites up to a certain proportion of reinforcement. The addition of 10 g reinforcement of spent tea leaves improved tensile strength by 33.46% and compressive strength by 38.86%. In terms of microstructural, morphological, and thermal characterization, in-depth SEM, EDS, XRD, UV, FTIR, TGA, and DSC analyses were performed. The results revealed that advanced microstructural, morphological, and thermal properties were improved with a certain proportion of spent tea leaf reinforcement. [ABSTRACT FROM AUTHOR]

In recent decades, the focus on the green composite speedily increases because they are low toxic, cheap, and available. A combination of naturally sourced polymetric polymer, suitable filler and excellent wettability and good filler/matrix interaction, synthesized with advance method and techniques appropriate to develop biocomposite with improved properties for different applications in marine, railway, construction and automobile industries. Although several naturally sourced material has been combined to achieve this aim, they're much agricultural waste that is underutilized. Nanocomposite shows acceptance for applications in different fields because the loading of small particles often of extensive surface material with captivating properties. It offers new technology and attracted opportunities for several sectors, such as MassTransit, automotive, aerospace, biotechnology, and nanotechnology industries. The combination nanofiller in natural fiber-filled composite enhances properties through the synergistic effect between the fiber and filler. This review provides information about various classes of natural fibers, nanofiller, based composite, nanocomposite, and natural fiber/nanofiller-based hybrid composite with specific concern to their applications. It also provides a summary of the emerging new aspects of milling techniques for synthesizing CaCO3 from snail shells and its application for developing hybrid composites for the sustainable and greener environment. [ABSTRACT FROM AUTHOR]

The agricultural industry is one of the main economic contributors in developing countries, especially in tropical regions. Extensive land clearing has led to severe erosion within the watersheds, which increases the vulnerability of water catchments to natural disasters, such as floods. Cellulosic fibers, such as jute, sisal, kenaf, hemp, and coir, are gaining increasing worldwide attention for their potential application in controlling soil erosion, principally due to their remarkable biodegradable and physical properties. Nonetheless, the research on biocomposites in controlling soil erosion is limited compared to the natural fibers. This is perhaps due to poor availability and high cost of biodegradable polymers compared to natural fibers, which are abundant and inexpensive. Poor adhesive interactions between the matrix and natural fibers due to the hydrophilic characteristic of the fibers is another major drawback that limits the development of biocomposites for controlling soil erosion. [ABSTRACT FROM AUTHOR]

Mechanical properties of Roselle fiber reinforced vinyl ester biocomposite were studied based on the fiber content and length in the present communication. Usually, natural fiber reinforced polymer composites depend on some aspects such as fiber content, fiber length and orientation, the fiber-matrix adhesion. Composite plates were prepared by a simple hand lay-up technique for two different fiber lengths (3 and 13 mm) and five different fiber content (10, 20, 30, 40 and 50 wt%). Composite specimens were tested according to ASTM and ISO standards and their results were recorded. Experimental results showed that mechanical properties such as tensile, flexural and impact, increases with increase of fiber content up to 40 wt% after which it is decreases at both the fiber length. However, modulus values were increased linearly with fiber content of 10 to 50 wt%. Composites with the fiber length of 13 mm show the high level of mechanical properties compared to composites with the fiber length of 3 mm at all combinations of fiber contents. It is observed that the optimal fiber content is 40 wt%, which can be used to obtain the maximum property level in the Roselle fiber reinforced vinyl ester composites. [ABSTRACT FROM AUTHOR]

Abstract Biocomposites are promising materials for traditional composites replacement in specific applications due to their interesting properties and sustainability. Although the composite components are manufactured near net shape, some machining operations, commonly drilling, are commonly required prior to mechanical joining of the components. Tool geometry, mainly the point angle of the drill, strongly affects the performance of the drilling process of composites in terms of machining induced damage. The aim of this work is analyzing the influence of the point angle of the drill on the damage generated during drilling of 100% biodegradable composite, using both numerical and experimental approaches. The novelty of the work relies on the lack of studies of drilling 100% biodegradable composites. The influence of the point angle on the thrust forces and hence in the machining induced damage was demonstrated. [ABSTRACT FROM AUTHOR]

Recycled polylactic acid (PLAr) was reinforced with treated nanocellulosic hemp fibers for biocomposite fabrication. Cellulosic fibers were extracted from hemp fibers chemically and treated enzymatically. Treated nanocellulosic fibers (NCF) were analyzed by Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Biocomposite fabrication was done with PLAr and three concentrations of treated NCF (0.1%, 0.25%, and 1% (v/v)) and then studied for thermal stability and mechanical properties. Increased thermal stability was observed with increasing NCF concentrations. The highest value for Young’s modulus was for PLAr + 0.25% (v/v) NCF (250.28 ± 5.47 MPa), which was significantly increased compared to PLAr (p = 0.022). There was a significant decrease in the tensile stress at break point for PLAr + 0.25% (v/v) NCF and PLAr + 1% (v/v) NCF as compared to control (p = 0.006 and 0.002, respectively). No significant difference was observed between treatments for tensile stress at yield.

A coupled device extruder and injection moulding were used to prepare biocomposites in order to provide a continuous and large-scale production, and overcome the fiber degradation inside the extruder. Two types of biocomposites were prepared, Sisal/poly(buthylene adipate-co-terephthlate) – PBAT and Juta/poly(lactide acid)/poly(buthylene adipate-co-terephthlate) blend. The biocomposites were prepared with fiber as-received and alkaline treated. The mechanical properties of biocomposites were increased by the fibers content; and the alkaline treatment was efficient to promote a good adhesion between fiber and polymer. In the case of the Juta fiber, the alkaline treatment used was too strong and led to fiber degradation. The results presented here show an alternative and continuous process to obtain biocomposites with relevant mechanical properties using fiber roving and avoiding fiber degradation.

The purpose of this article is to understand the influence of typical composite parameters (interfacial bond strength, surface-area and fibre mechanical properties) on the tensile properties of nonwoven composite materials. The materials investigated were flax, hemp and Poly-(propylene) (PP) and Maleic Anhydride-grafted PP (MAPP), which provide different configurations in terms of fibre mechanical properties, bundle individualization and fibre/matrix interface. Whereas hemp fibres exhibit poorer tensile properties and lower bundle individualization than flax fibres, their higher lignin content evaluated by FT-IR analysis improves the interfacial shear strength (IFSS) with PP and MAPP. However, the tight interface developed with hemp fibres has only a weak effect at the scale of composites. With low-IFSS systems such as plant fibres associated with polyolefin matrices, mechanical properties at the macroscale are governed by the fibre mechanical properties and bonding area rather than by the interfacial bond strength. [ABSTRACT FROM AUTHOR]

The aim of this study is to propose and explore a novel approach for the production of cellular lightweight natural fibre, nonwoven, fabric-reinforced biocomposites by means of gas dissolution foaming from composite precursors of polyhydroxybutyrate-based matrix and flax fabric reinforcement. The main challenge is the development of a regular cellular structure in the polymeric matrix to reach a weight reduction while keeping a good fibre-matrix stress transfer and adhesion. The viability of the process is evaluated through the analysis of the cellular structure and morphology of the composites. The effect of matrix modification, nonwoven treatment, expansion temperature, and expansion pressure on the density and cellular structure of the cellular composites is evaluated. It was found that the nonwoven fabric plays a key role in the formation of a uniform cellular morphology, although limiting the maximum expansion ratio of the composites. Cellular composites with a significant reduction of weight (relative densities in the range 0.4-0.5) were successfully obtained. [ABSTRACT FROM AUTHOR]

This work deals with fibrous biocomposites prepared by using nettle and poly(lactic acid) fibers and employing carding and compression-molding processes. The role of carding process in determining the tensile strength of the biocomposites was analyzed. The tensile, bending and impact properties of the biocomposites were found to increase initially with the increase of nettle fiber content till 50 wt% and decrease afterwards. The thermogravimetric analysis inferred that the thermal stability of the biocomposites increased with the increase of nettle fiber content. The dynamic mechanical analysis showed that the biocomposites exhibited high storage modulus, low loss modulus, and low damping factor. Further, the biocomposites exhibited excellent biodegradability and their biodegradability increased with the increase of nettle fiber content. Overall, the biocomposite prepared with equal weight proportion of nettle and poly(lactic acid) showed high potential for automotive dashboard panel application. [ABSTRACT FROM AUTHOR]

Natural fibers are not as rigid as glass or carbon fibers. During composites extrusion and injection molding, they tend to bend and twist in the polymeric matrix, thus resulting in fiber waviness and decreased mechanical properties of natural fiber composites. The most widely used models for the estimation of interfacial shear strength (IFSS) and elastic modulus, which consider the fiber aspect ratio and mechanical properties of the fiber and matrix, do not consider these important features. In order to account for fiber waviness, an effective fiber length is proposed in this paper. The undulation of the fibers is approximated with a sinusoidal arc along with a calculated new length. The proposed correction factor depends on the wavelength and amplitude of the wave approximating the fiber. To verify this method, blends of polylactic acid (PLA) and polycarbonate (PC) (prepared with and without an interchange reactions catalyst) with addition to various percentages of cellulosic fibers (5 wt%, 10 wt% and 15 wt%) have been prepared and characterized. It has been demonstrated that by considering the corrected length values, it is possible to predict the mechanical properties and the effective reinforcement attained in the composites by using the most widely used models. In particular, the prediction of the elastic modulus is slightly affected by this correction, whereas the calculation of IFSS is strongly dependent on it. [ABSTRACT FROM AUTHOR]

[Display omitted] Plastic pollution has become a global threat to humanity. Fortunately, humanity has always found ways of overcoming such threats through multipronged approaches. To overcome this current threat brought about by anthropogenic linear pattern of take-make-use-dispose of fossil-based plastics, an intentional approach of adopting biobased plastics which are renewable has taken shape. In this approach, governments, industry, and academia are at the forefront of making determined commitments to slow down the spiralling carbon footprint and aim at net zero carbon emissions by 2050. In this regard, PHAs which have a rich resume of desired properties to replace non-renewable fossil-based plastics are increasingly becoming popular. However, PHA production cost is still high compared with the fossil-based plastics and there exists properties performance gap because they are typically brittle, especially the short chain length PHAs (Scl-PHAs). Considerable efforts are geared towards tuning the mechanical properties as well as reducing the cost to meet the market requirements. The most authentic way of tackling these twin-challenges of reducing the cost of PHA products and their properties enhancement is the incorporation of fillers sourced from renewable sources, especially the plant biomass. In this comprehensive review, Scl-PHAs biopolymers are discussed, their modifications with plant biomass (natural fibres and components, agro-residues, and industrial residues) are elucidated. Moreover, their wide scope of applications, sustainability performance (biodegradation studies) and other viable end-of-life options are amply discussed. Finally, we draw conclusions and highlight future opportunities in this exciting bioplastic area. [ABSTRACT FROM AUTHOR]

In this paper, analytical and 3D numerical models are developed to investigate the mechanical behavior of sandwich pipe under internal pressure loading. The suggested models provide an exact solution for stresses, strains and displacement on the sandwich pipe, which is made of epoxy material for the core layer and reinforced materials with an alternate-ply for the skin layers. The aim of this analysis is to evaluate the potential applications of jute and pineapple leaf fiber (PALF) bio-fibers in order to replace glass synthetic fibers generally employed in sandwich pipes. In this subject, a failure analytical analysis was developed using TSAI-WU criterion. The results of stress, strain and displacement distribution through the thickness are presented for the analytical and numerical models. The comparison between the both models results show a very good agreement. In order to increase the rigidity of a biocomposite sandwich and reduce the gap compared with a synthetic sandwich, a gradual reinforcing of layer numbers was chosen, which permitted the best behavior. The ultimate pressure and safety factors obtained by increasing biocomposite layers are significant for composite transportation pressure pipelines, especially for sandwich pipe based on PALF/epoxy. • We aim at modeling a sandwich pipe under internal pressure loading using analytical and 3D numerical models for failure analysis. • The structure is a made of epoxy material for the core layer and reinforced materials with an alternate-ply for the skin layers. • Evaluate the potential applications of bio-fibers in order to replace synthetic fibers generally employed in sandwich pipes using TSAI-WU criterion. • Substituting synthetic fibers by bio-fibers yields a satisfactory result by increasing the number of layers. [ABSTRACT FROM AUTHOR]

Natural fiber reinforced polymer-based composites have been growing into a type of green composites. The properties of natural fiber reinforced polymer-based composites are closely related to the structure of natural fibers. Bagasse fiber (BF) is one of the most used natural fibers for preparing natural fiber reinforced polymer-based composites. However, few examples of previous research touch on the quantitatively characterization of structure of BF and its effect on the properties of BF reinforced polymer-based composites. In this work, four kinds of BF including untreated BF (UBF), alkali treated BF (ABF), BF modified by silane coupling agent (SBF), and BF modified combining alkali treatment with silane coupling agent (ASBF) were prepared and melting blended with polylactic acid (PLA) to prepare PLA/BF composites. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), thermogravimetry (TGA) and mechanical properties testing were used to characterize and analyze the structure and properties of modified BF and its reinforced PLA-based composites. Results showed that the used methods changed the structure of BF and their bonding modes. The surface energies of UBF, ABF, SBF, and ASBF were 19.8 mJ/m2, 34.7 mJ/m2, 12.3 mJ/m2, and 21.6 mJ/m2, respectively. The O/C ratios of UBF, ABF, SBF and, ASBF are 0.48, 0.53, 0.47, and 0.51. Due to the synergistic effect of alkali treatment and silane coupling agent modification on the surface chemical properties, the content of silicon elements on the surface of ASBF (4.15%) was higher than that of ASBF (2.38%). However, due to the destroying of alkali treatment on the microstructure of BF, the alkali treatment had no prominently synergetic effect with coupling agent modification on the mechanical properties of PLA/BF composites. Alkali treatment removed the small molecular compounds from BF, decreased its thermal stability, and increased the crystalline region and crystallinity of cellulose. Meanwhile, alkali treatment made BF fibrillated and increased its contactable active area with the coupling agents, but destructed the nature structure of BF. The silane coupling agent played a more important role than alkali treatment did in improving the interfacial compatibility of PLA/BF composites.

A study of the impact behaviour and the post-impact residual strength of fully biodegradable composites is presented in this work. To this end, low-velocity impact tests and compressive residual strength tests were carried out on flax/PLA laminates. The results were compared with carbon/epoxy laminates, showing some important advantages in terms of absorbed energy and normalized residual strength. The reason was attributed to different energy absorption mechanisms; the main failure mode in flax/PLA laminates is fibre failure while residual strength of carbon/epoxy laminates is dominated by delaminations. [ABSTRACT FROM AUTHOR]

Composite materials based on renewable agricultural and biomass feedstocks are increasingly utilized as these products significantly offset the use of fossil fuels and reduce greenhouse gas emissions in comparison with conventional petroleum-based materials. However, the inclusion of natural fibers in polymers introduces several challenges, such as excess water absorption and poor thermal properties, which need to be overcome to produce materials with comparable properties to the conventional composite materials. Instead of using rather expensive chemical and physical modification methods to eliminate these aforementioned challenges, a new trend of utilizing waste, residues, and process by-products in natural fiber-polymer composites (NFPCs) as additives or reinforcements may bring considerable enhancements in the properties of NFPCs in a sustainable and resilient manner. In this paper, the effects of waste materials, residues or process by-products of multiple types on NFPCs are critically reviewed and their potential as NFPC constituents is evaluated. [ABSTRACT FROM AUTHOR]

The production of ligno-cellulosic biomass-based composites requires the development of new methodologies to evaluate the reinforcement potential of a given biomass, such as miscanthus studied in the work. Miscanthus stems from thirteen genotypes were broken into elongated fragments and mixed with polypropylene composites in an internal mixer. The aim is to find the best protocol able to discriminate miscanthus genotypes for their reinforcement capability. The following process parameters were optimized in order to maximize the reinforcement effect of the stem fragment filler: mixing parameters (mixing time, rotor speed and chamber temperature), temperature, fragment content, size and length distributions and coupling agent. The relationship between the process parameters and the mechanical properties of composites were analyzed to evaluate the influence of genotype on reinforcement performance, showing the robustness of the protocol in effectively discriminating genotypes according to their reinforcing capacity. [ABSTRACT FROM AUTHOR]

Biodegradable fiber-reinforced biocomposites from steam-exploded coconut fibers and polylactic acid (PLA) and polybutylene succinate (PBS) plastic were developed in this study. Biocomposite filaments and samples were produced using a commercial-scale screw extruder and a 3D printer, respectively. In-depth mechanical and thermal analyses were also performed. The results showed that the tensile strengths of PLA mixed with 3% coconut fiber (PLA97/F3) and 6% coconut fiber (PLA94/F6) decreased by approximately 22% and 23%, respectively, compared to the 64% reduction of that of the original PLA after four-week storage. The bending modulus of the PLA/fiber composite was better than that of the original PLA (21–29% higher), whereas a 5–8% improvement was observed for the PLA/PBS/fiber composites. The impact strengths of PLA97/F3 and PLA77/PBS20/F3 were approximately 8.5% and 7.4% higher than those of the original PLA and PLA/PBS, respectively. During the degradation test, both PLA97/F3 and PLA77/PBS20/F3 exhibited higher tensile strengths than the original materials. Finally, this research presents encouraging results for the production of biodegradable fiber-reinforced biocomposites that are applicable to 3D printing platforms. The final products can be used as replacement or aftermarket components of automobiles. • PLA, PBS, and steam-exploded coconut fiber were used for filament production. • The 3D-printed biocomposites were subjected to mechanical and thermal tests. • Coconut fiber is effective as a natural fiber reinforcement material. • The products have higher tensile strengths than original materials during degradation test. [ABSTRACT FROM AUTHOR]

Environmental awareness of the global waste problem has driven the development of new green composites made from either renewable or biodegradable materials. Among the variety of available green composites, natural composites based on poly-lactic acid (PLA) have shown noteworthy performance due to their short degradation time after disposal, good strength, and ease of processing by conventional methods. In particular, green composites manufactured with PLA matrix reinforced with Manicaria Saccifera fabric (MF) display mechanical properties that have shown to be very competitive compared with similar materials. In this study, the tensile properties of a green composite of PLA reinforced with MF are optimized by using a Taguchi method approach. The processing parameters, fabric chemical treatment parameters, compression molding parameters, and fiber content are analyzed simultaneously to yield the optimum biocomposite properties. The predicted optimum parameters are experimentally verified. Tensile tests and scanning electron microscope (SEM) analysis are used. Significant improvements on both the tensile strength (114.2%), and the elastic modulus (120.6%) of the biocomposite are achieved. [ABSTRACT FROM AUTHOR]

One of the big global, environmental, and socioeconomic challenges of today is to make a transition from fossil fuels to biomass as a sustainable supply of renewable raw materials for industry. Growing public awareness of the negative environmental effects of petrochemical-based products adds to the need for alternative production chains, especially in materials science. One option lies in the value-added upcycling of agricultural byproducts, which are increasingly being used for biocomposite materials in transport and building sector applications. Here, sunflower by-product (obtained by grinding the stems) is considered as a source of natural fibers for engineered biocomposite material. Recent results are shown for the main mechanical properties of sunflower-based biocomposites and the socioeconomic impact of their use. This paper demonstrates that sunflower stem makes a good candidate feedstock for material applications. This is due not only to its physical and chemical properties, but also to its socioeconomic and environmental rationales. [ABSTRACT FROM AUTHOR]

The clean and sustainable development of biomass resources has attracted tremendous attention to alleviate the increasingly serious energy depletion and environmental problems. Hence, it is urgently needed to design a green product through a cleaner production strategy to bridge the gap between materials and sustainability toward environmental protection and practicality. Herein, a bamboo fiber/polybutylene succinate (PBS) biocomposite that carries silver nanoparticles (AgNPs) with electromagnetic interference (EMI) shielding and antibacterial activity, as well as the performance of interface reinforcement, were prepared using a green, efficient, and scalable bionic strategy of PDA coupling with minimal environmental footprint. The proposed bamboo fiber/PBS biocomposites, which showed multifunctionality and environmental adaptability, revealed good antibacterial activity, where the average inhibition zone diameters against E. coli and S. aureus bacteria reached 5.37 ± 0.36 and 3.96 ± 0.74 mm, respectively. Simultaneously, gains in the EMI shielding effectiveness (∼29.72 dB) and mechanical properties (improved by 24.58% in tensile strength, 39.13% in tensile modulus, 14.60% in flexural strength, and 19.67% in flexural modulus) were realized. Overall, this work displays a novel pathway toward eco-friendly and multifunctional nature fiber/polymer composites for high-value utilization. A green and sustainable natural fiber-reinforced polybutylene succinate biocomposite carrying silver nanoparticles based on a clean, simple and bionic strategy was proposed for antibacterial application and electromagnetic interference shielding. [Display omitted] • An eco-friendly biocomposite was realized via a green and bionic strategy. • AgNPs were synthesized through a clean synthetic route. • Biocomposites exhibit a remarkable EMI shielding effectiveness. • Enhanced interfacial interaction was attained. • Biocomposites possess antibacterial performance towards E. coli and S. aureus. [ABSTRACT FROM AUTHOR]

Kenaf (Hibiscus cannabinus L.; Family: Malvaceae), is multipurpose crop, one of the potential alternatives of natural fiber for biocomposite materials. Longer fiber and higher cellulose contents are required for good quality biocomposite materials. However, average length of kenaf fiber (2.6 mm in bast and 1.28 mm in whole plant) is below the critical length (4 mm) for biocomposite production. Present study describes whether fiber length and cellulose content of kenaf plants could be enhanced by increasing GA biosynthesis in plants by overexpressing Arabidopsis thaliana Gibberellic Acid 20 oxidase (AtGA20ox) gene. AtGA20ox gene with intron was overexpressed in kenaf plants under the control of double CaMV 35S promoter, followed by in planta transformation into V36 and G4 varieties of kenaf. The lines with higher levels of bioactive GA (0.3- 1.52 ng g-1 fresh weight) were further characterized for their morphological and biochemical traits including vegetative and reproductive growth, fiber dimension and chemical composition. Positive impact of increased gibberellins on biochemical composition, fiber dimension and their derivative values were demonstrated in some lines of transgenic kenaf including increased cellulose content (91%), fiber length and quality but it still requires further study to confirm the critical level of this particular bioactive GA in transgenic plants. [ABSTRACT FROM AUTHOR]

In this study, oil palm mesocarp fiber (OPMF) was treated with superheated steam (SHS) in order to modify its characteristics for biocomposite applications. Treatment was conducted at temperatures 190-230 °C for 1, 2 and 3 h. SHS-treated OPMF was evaluated for its chemical composition, thermal stability, morphology and crystallinity. OPMF treated at 230 °C exhibited lower hemicellulose content (9%) compared to the untreated OPMF (33%). Improved thermal stability of OPMF was found after the SHS treatment. Moreover, SEM and ICP analyses of SHS-treated OPMF showed that silica bodies were removed from OPMF after the SHS treatment. XRD results exhibited that OPMF crystallinity increased after SHS treatment, indicating tougher fiber properties. Hemicellulose removal makes the fiber surface more hydrophobic, whereby silica removal increases the surface roughness of the fiber. Overall, the results obtained herewith suggested that SHS is an effective treatment method for surface modification and subsequently improving the characteristics of the natural fiber. Most importantly, the use of novel, eco-friendly SHS may contribute to the green and sustainable treatment for surface modification of natural fiber. [ABSTRACT FROM AUTHOR]