Search

Context: The effect of X (X = O, Se, N, P, F, Cl) doping on the adsorption of Zn atoms by WS2 was investigated based on first principles. The electronic structure and optical properties of the adsorbed system after atomic doping were calculated. It is found that the Zn atom adsorbed on the W top (Tw) site has the most stable structure. When an S atom is replaced with an X atom based on the adsorption system, where the adsorption energy decreases after doping of O, P, F, and Cl atoms compared to the undoped system, it means that each system is more stable after doping of these atoms; charge transfer shows that the adsorption system after P-atom doping the system around the Zn atom loses electrons while S-atom gains electrons, which indicates that P-atom doping is favorable for the adsorption of Zn by WS2, N, P-atom is introduced as p-type doping and F, Cl-atom is introduced undoped by n-type doping, and the band gap of the doped system is less than that of the undoped one. With the introduction of different dopant atoms, certain impurity energy levels are introduced into the adsorption system. The prohibited bandwidth around the Fermi energy level reduces the density of states, causing the doped system's density of states to shift to lower energies, among which the shifts of N, P, F, and Cl are more pronounced. The P-doped adsorption system shows a new peak near the energy of − 11 eV. In addition, the study of optical properties showed that the peak reflections of both doped and non-doped systems adsorbing Zn atoms appeared in the ultraviolet region; the absorbance coefficient of the doped system is moved in the lower energy direction and red-shifted after atom doping; in addition, the absorption coefficients and reflectance of the P, Se doped systems are enhanced in the wavelength range of 200–300 nm compared with that before doping, the dielectric function and CBM and VBM positions were also calculated further indicating the potential of Se-doped systems in improving photocatalytic efficiency. Methods: In this paper, the structure optimization of X (X = O, Se, N, P, F, Cl) doping on WS2 adsorbed Zn atom model is performed based on the CASTEP module in Materials-Studio software under the first principles using GGA and PBE generalized function. The corresponding binding energies, bond lengths, bond angles, charge densities, energy band structures, densities of states, and optical properties were also analyzed. The Monkhorst–Pack particular K-point sampling method is used in the calculations; the K-point grid is 6 × 6 × 1, and the cutoff energy for the plane wave expansion is 500 eV. After geometric optimization, the iterative accuracy converges to a value of less than 1 × 10−5 eV/atom for the total energy of each atom and less than 0.03 eV/Å for all atomic forces. The thickness of the vacuum layer was set to 20 Å to avoid the effect of interlayer interaction forces. In this paper, 27 atoms were used to form a 3 × 3 × 1 supercellular tungsten disulfide system consisting of 18 S atoms and 9 W atoms. [ABSTRACT FROM AUTHOR]

Context: To lessen the impact of the dangerous metal Cr, this paper applies the first principles to investigate the adsorption behavior and photoelectric properties of GaS on Cr. The effects of doped GaS on Cr adsorption behavior are investigated with four GaS systems, which are pure, boron (B)-doped, nitrogen (N)-doped, and oxygen (O)-doped, in order to maximize the characteristics of GaS for use in novel sectors, to obtain understanding of the impact of doping on the electronic structure and optical properties of GaS adsorption of Cr, as well as to promote the development of the material. Four GaS adsorbed Cr systems, pure, B-doped, N-doped, and O-doped, are optimized, and the optimized results show that the stable adsorption position of Cr on both pure and doped GaS is the top position of Ga atoms, whereas doped elements B, N, and O can promote the adsorption of Cr on GaS, and the order of the strength of this promotion is B > N > O. Method: In this paper, molecular simulation calculations and analyses using the CASTEP module in the software Materials Studio are performed to simulate the structure optimization of GaS-adsorbed Cr materials doped with B, N, and O atoms by using the generalized gradient approximation (GGA) plane-wave pseudopotential approach [1] and the Perdew-Burke-Ernzerhof (PBE) generalized function [2]. From the convergence test, it is reasonable to set the K-point network to 4 × 4 × 1 and the truncation energy to 500 eV [3]. In this paper, a 3 × 3 × 1 supercell structure with 18 S atoms and 18 Ga atoms is selected. The convergence value of the iterative accuracy is 1.0e − 5 eV/atom, and all the atomic forces are less than 0.02 eV/Å. A vacuum layer of 16 Å is also set in the C direction to avoid interlayer interactions of GaS. First, we optimize the geometry of the model and then analyze the nature of the adsorption energy and electronic structure corresponding to the model. [ABSTRACT FROM AUTHOR]

Context: The electronic properties and optical properties of Cr-doped monolayer WS2 under uniaxial compressive deformation have been investigated based on density functional theory. In terms of electronic structure properties, both intrinsic and doped system bandgaps decrease with the increase of compression deformation, and the values of the bandgap under the same compression deformation after Cr doping are reduced compared with the corresponding intrinsic states. When the compressive deformation reaches 10%, both the intrinsic and doped system band gaps are close to zero. New electronic states and impurity energy levels appear in the WS2 system when doped with Cr atoms. For the optical properties, the calculation and analysis of the dielectric function under each deformation regime of monolayer WS2 show that the compression deformation affects the dielectric function, and when the compression deformation is 10%, the un-doped and Cr-doped regimes show a decrease in ε1(ω) compared to the compression deformation of 8%. For each deformation system, the peak reflections occur in the ultraviolet region. Near the position where the second peak of the absorption spectrum appears, it can be seen that the ability of each system to absorb light gradually decreases with the increase of the amount of deformation and appears to be red-shifted to varying degrees. Methods: This study follows the initial principles of the density functional theory framework and is based on the CASTEP module of Materials-Studio software GGA and PBE generalizations are used to perform computations such as geometry optimization of the model. We have calculated the energy band structure of monolayer WS2 with intrinsic and compressive deformations of 2% and 4% using PBE and HSE06, respectively. The band gap values calculated using PBE are 1.802 eV, 1.663 eV, and 1.353 eV, respectively, and the band gap values calculated with HSE06 are 2.267 eV, 2.034 eV, 1.751 eV. The results show that the bandgap values calculated by HSE06 are significantly higher than those calculated by PBE, but the bandgap variations calculated by the two methods have the same trend, and the shape characteristics of the energy band structure are also the same. However, it is worth noting that the computation time required for the HSE06 calculation is much longer than that of the PBE, which is far beyond the capability of our computer hardware, and the purpose of this paper is to investigate the change rule of the effect of deformation on the bandgap value, so to save the computational resources, the next calculations are all calculated using the PBE. The Monkhorst–Pack special K-point sampling method is used in the calculations. The cutoff energy for the plane wave expansion is 400 eV, and the K-point grid is assumed to be 5 × 5 × 1. Following geometric optimization, the iterative precision converges to a value of less than 0.03 eV/Å for all atomic forces and at least 1 × 10−5 eV/atom for the total energy of each atom. The vacuum layer's thickness was selected at 20 Å to mitigate the impact of the interlayer contact force. [ABSTRACT FROM AUTHOR]