Search

The Siamese people utilized the bark of the Coi tree (Streblus asper Lour.) to manufacture paper approximately 330 years ago. However, there are no studies yet related to the chemical properties of Coi bark as well as the morphological properties of Coi bark fiber and Coi pulp fiber. This research paper discussed such properties of Coi bark. The results indicated that Coi bark possessed a chemical composition that could potentially be used for pulp production, although it contained a high value of ash content, due to many calcium particles in the bark. Even though Coi pulp fibers were very long and stiff, with small lumens and thick cell walls, they could be felted naturally on a washing screen to make a strong wet sheet. This was due to a high felting power of fibers derived from a high value of fiber length and slenderness ratio. Therefore, the handsheets produced from Coi pulp fiber were obtained without chemical and beating treatments. These observations mean that both the archaeological and industrial applications of Coi bark, i.e., an ancient Samud Coi preservation and a new potential source of pulp fiber, are possible. [ABSTRACT FROM AUTHOR]

The objective of this study was to characterize the properties of pulp and paper produced from tea (Camellia sinensis) wastes, an agricultural residue widely available in Turkey, using the kraft-anthraquinone (AQ) cooking method. The chemical components and fiber morphology of tea wastes were investigated. The results indicated that tea wastes had low holocellulose, cellulose, and a-cellulose contents and high lignin content. Also, the suitability of the fiber for pulp and paper production was examined, and the fiber length, fiber width, lumen diameter, and cell wall thickness were measured. According to these values, it was found that the strength properties of papers obtained from tea wastes were insufficient. Therefore, tea waste pulps were mixed with Turkish pine pulps at various ratios. Twelve different cooking experiments were performed on the tea wastes, and the cooking with the best pulp yield was used for mixing. The second cooking, with 0.1% AQ, gave the best yield (33.26%), an increase of about 3.51% compared to the first cooking with no AQ. The physical and optical properties of the papers were also examined. Results showed that paper properties were improved by increasing the Turkish pine pulp rate. Consequently, tea wastes can be used in pulp and paper production when combined with softwood pulps. [ABSTRACT FROM AUTHOR]

This study investigates the operating conditions used in the sodaanthraquinone pulping of Eucalyptus globulus wood after autohydrolysis pretreatment on the yield, kappa number, and brightness of the resulting unbleached pulp. Moreover, strength-related properties of the resulting handsheets was examined to identify the best pulping conditions and compare the outcome with that of a conventional soda-anthraquinone pulping process. The paper strength properties of the pulp were similar to or better than papers made from soda-AQ delignified pulps conducted in a single step. Also, a liquid fraction with a substantial content in hemicellulosic extracts was recovered in the simplified process. Autohydrolysis of the raw material facilitates carrying out soda-AQ pulping under milder conditions. In addition, autohydrolysis improves other properties relative to paper from raw cellulose pulp. Yield, kappa number, and brightness for pulp from solid residues of autohydrolysed eucalyptus wood were similar to those for pulp from untreated eucalyptus wood. [ABSTRACT FROM AUTHOR]

Biomaterials from olive tree pruning are an abundant agricultural residue in various Mediterranean regions. A suggested use of this residue is its separation in a main fraction (trunks and stems with diameter > 1 cm) and a residual fraction (leaves and stems with diameter 1 < cm), using biorefinery procedures. The main fraction is cooked with ethanol, giving rise to a pulp, which can be used either in paper or in bioethanol production if before pulping the main fraction is subjected to a hydrothermal treatment. Pulping with 70% ethanol concentration, 185 °C for 80 min resulted in a pulp with a yield of 46.30% and a content of holocellulose, α-cellulose, and lignin of 77.17%, 62.49%, and 21.73%, respectively. The paper sheets obtained had a breaking length of 1168 m, a burst index of 0.44 kN /g, a tear index of 2.25 mN.m²/g, and a brightness of 43.66%. The pulp converted into bioethanol (by simultaneous hydrolysis and fermentation) achieved a conversion of 70 g bioethanol/100 g potential bioethanol. The residual fraction of olive tree prunings was subjected to combustion to produce thermal energy. The heating value was 18700 kJ/kg, the flame temperature range was 1094 to 2013 ºC, and the dew point temperature range of the flue gases was 47 to 53 °C. [ABSTRACT FROM AUTHOR]

A variety of the Leucaena genus, Leucaena diversifolia, was used for pulp and paper making by kraft and refining processes and a OD(EP)DP bleaching sequence. The same species has been suggested as an energy crop and, in fact, this species used shows a high gross heating value; besides, this variety of Leucaena has appropriate characteristics for pulp and paper making. The holocellulose content was higher than Eucalyptus globulus, and ash and lignin contents were comparable to other varieties of Leucaena. Pulps with a kappa number between 17 and 18, and 21.4 cP viscosity were obtained using an active alkali concentration of 31%. Also, paper sheets showed good strength properties, comparable or even greater than those obtained with Eucalyptus or others varieties of Leucaena at comparable refining degrees, between 30 and 40 °SR. The pulp was successfully bleached in all cases with a kappa number below 1.5 in the EP stage and a value of brightness higher than 90%. [ABSTRACT FROM AUTHOR]