Search

The harsh indoor environment in winter in the hot-summer and cold-winter zones of China and the increasing demand for winter heating from residential consumers have prompted more and more researchers to address the energy-efficient heating problem in non-centralized heating areas. A computational fluid dynamics model of a typical building was developed to analyze the dynamic heat transfer characteristics and energy consumption of interior partitions under decentralized heating in this region, of which the accuracy of the established model was proved by the relative error of less than 5% compared with the experimental measurement. Then seven typical kinds of interior partition configurations with different wall thickness, wall material, and insulation layer locations were developed and evaluated through simulation analysis. Transient heat storage ratio and cumulative heat storage ratio were proposed to demonstrate the dynamic heat transfer characteristics of interior partitions. The simulation results showed that 180 mm and 220 mm solid clay bricks can reduce energy consumption by 17.56% and 30.23%, respectively, compared with 120 mm solid clay bricks. The energy consumption of fly ash aerated concrete and solid clay brick partitions were reduced by 10.18% and 19.02%, respectively, compared with porous concrete partitions. The dynamic heat transfer characteristics of internal partitions with internal insulation were similar to those with external insulation due to the reduction in unnecessary energy consumption transferred to adjacent unheated rooms by about 20% compared to that without insulation. And the heat consumption of interior partitions under convective heating was 17.3% higher than under radiant heating. [ABSTRACT FROM AUTHOR]

The industrial sector is one of the biggest oil consumers in Cyprus, corresponding to 20% of the fuel consumption. A parabolic trough collector (PTC) system seems the best option to produce clean thermal energy at higher temperatures than those that can be achieved from the already widely used flat plate collectors on the island. This paper presents a simulation model built to investigate the performance of the first industrial PTC system in Cyprus, installed at the Cyprus biggest soft drinks factory. The simulation model is built in TRNSYS and is validated using data from the real PTC system installed at the factory. The results show a very good fitting between the operating parameters and the power output of the Solar Field (SF), Concrete Thermal Storage System (CTES), and the Steam Generator (SG). The average percentage relative error of the system's contribution to the process is less than 6.32% for the daily steam production and during a week did not exceed 6.45%. The novelty of this study is the development of a design tool that can be used by potential interested industries to identify the suitable system that fits their needs. All data are provided in the form of graphs and allow anyone to use as input data the thermal energy demand and required steam temperature of the industry to retrieve information about the size of a suitable system which satisfies these requirements depending on each case. The payback period for all cases examined varies from 2 to 6 years, depending on the size of the system. • Validated dynamic simulation model of a PTC system working under various operation modes for Industrial Process Heat application. • Evaluation of the operation modes and strategies developed to make the PTC system dispatchable. • A scaled up model for of the validated dynamic simulation model. • Development of a tool for potential interested industries in Cyprus for PTC systems. [ABSTRACT FROM AUTHOR]

Sensible thermal energy storage is the most common solution for small-to-medium solar process heat systems. Hence, it is vital to enhance the thermal stratification and energy utilization of stratified tanks. In this study, four process heat systems are dynamically simulated: 1) S0 with a single outlet port to the load, 2) S1 with a single port and a thermostatic mixing valve, 3) M0 with multiple ports, and 4) M1 with multiple ports and a mixing valve. Two novel models are proposed for the compound parabolic collectors and the stratified tanks. System M1, with annual system efficiency of 47.3% and solar fraction of 0.57, was found to be the best-performing one, followed by S1, M0, and S0. System M1 also reduced the annual energy consumption of the backup heater in S0 by 16.45%. The thermostatic mixing valve reduced the thermocline thickness. The incorporation of both mixing valve and multiple ports delayed the startup of the heater, reduced the system's thermal losses, and slightly improved the collectors' efficiencies. The proposed tank model can be a viable tool for solar energy designers to optimize the number and relative positions of the inlet and outlet ports for maximized system efficiency and solar coverage. [Display omitted] [ABSTRACT FROM AUTHOR]

A nuclear heating system integrated with a heat storage tank (HST-NHS) is a promising technical solution for countries with large-scale heating demand. HST-NHS can greatly curtail carbon dioxide emissions and contribute to sustainable development. Appropriate control strategies are not only crucial to realize the real-time matching between HST-NHS heat supply and heat demand, but also ensure the stable and safe operation of HST-NHS. Until now, control strategies for HST-NHS have received limited attention. A refined dynamic simulation model for HST-NHS is established based on APROS software. The verification of the built model in steady state and transient state is completed. Two basic control strategies for the primary heating network (PHN) of HST-NHS, constant supply water temperature and variable flow rate (CT-VF) and variable supply water temperature and constant flow rate (VT-CF) are presented in detail. Based on various typical working conditions of a central heating region in Liaoyuan City, the control effects of two control strategies are investigated. Additionally, a comprehensive performance comparison between the two strategies is explored. Simulation results indicated that under the two control strategies, the indoor temperature can be effectively controlled at a high comfort level. During the same typical day, the total energy consumption cost under the VT-CF control strategy is 0.5 × 105 yuan lower than that under the CT-VF control strategy. • Dynamic model of nuclear heating system with heat storage is developed. • The verification of the built model in steady and transient state is completed. • Control effects of two basic control strategies during typical days are evaluated. • A performance comparison of two basic control strategies is conducted. [ABSTRACT FROM AUTHOR]

• An innovative slim decentralised plug-and-play tank is proposed for DHW production. • Model calibration is performed by experimental data in charge/discharge process. • Retrofit solution cuts required annual energy in half of which 82% is RES quota. • Optimised charging scheme reduces the total annual electrical energy by 5.2 %. • A degree increment in draw-off temperature increases annual CO 2 emission by 103 kg. The present study deals with a multi-objective analysis of an innovative decentralised system to produce and store domestic hot water (DHW), emphasising on the combined effects of the technological aspect, control strategy and user's behaviour. The proposed system, by relying on thermal energy storage, decouples energy production and demand while shaves peaks in the energy demand and, at the same time, provides more autonomy to users through local storages. To identify subtle interactions in components of DHW system, dynamic simulations are carried out by establishing a coupled TRNSYS-MATLAB code, calibrated and validated by experimental measurements. The energy analysis implies that the proposed system cuts the required annual electrical energy in half, of which up to 82% of needed primary energy is supplied from renewable sources, compared to previous electrical-decentralised system. The optimisation of the results through applying control strategies indicates that adopting a three-time charging scheme is advantageous in terms of providing a more stable temperature profile as well as a higher hot water temperature. Compared to an available-by-demand operation, this scheme reduces the required total annual electricity by 5.2 % and enhances total thermal loss from components up to 4.0%. Furthermore, a sensitivity analysis on the results emphasises the striking role of the user behaviour in electrical energy consumption either via draw-off temperature or adjusting the pre-defined temperature for activation of the built-in auxiliary heater. [ABSTRACT FROM AUTHOR]

• A new energy system is developed and examined using dynamic modelling to meet the needs of a two-story structure. • To decrease the size of the plant, including the PVT size and fuel consumption, the PCM is incorporated into the building. • Fuel consumption and prices are reduced by 17.24% and 8.57%, respectively, using the suggested approach. • Exergy efficiency, unit product cost, and CO 2 emission of 64.3 %, 0.26 $/kWh, and 0.21 kg/kWh are obtained respectively at optimum point. The buildings energy sector is expected to account for 40% of total world energy consumption and 40% participation on total carbon dioxide emissions, according to the International Energy Agency reports. The present study proposes a novel integrated system to meet all loads of the house's energy requirements. The system employs a heat storage tank rather than pricey batteries, which helps to keep the total cost of the system as low as feasible. Also, the system is developed for an on-grid operation, being capable to sell surplus energy to the grid helping to reduce the payback time. Dynamic modeling is conducted to analyze the system performance to provide heating, cooling and power demands of a case study building, for which two scenarios of with and without Phase Change Material (PCM) incorporation is considered. The influence of critical design factors is investigated, after which a tri-objective optimization is carried out. It was found that, the integration of PCM energy storage would reduce the annual heating and cooling demands of the building by 25.6%. As a result, the exergy efficiency of the proposed system increases by 13 % and the product cost is reduced by 8.57%. Based on the obtained yearly average results, the proposed building energy system yields exergy efficiency, unit product cost, and CO 2 emission of 64.3 %, 0.26 $/kWh, and 0.21 kg/kWh, respectively. [ABSTRACT FROM AUTHOR]