Search

The primary aim of this research was to explore the feasibility of producing environmentally friendly composite materials by employing diverse hybrid matrices consisting of dammar natural resin, supplemented with small proportions of two synthetic resins: one epoxy and the other acrylic. A blend of paper and chicken feathers served as the reinforcing elements. The fabrication of these composite materials utilized a hand layup technique. Targeted for applications in the furniture industry or interior design, their mechanical properties were assessed through various tests. Specimens were obtained from the manufactured samples and subjected to evaluations for tensile strength, compression, flexure, vibrations, Shore hardness, and water absorption. Results indicated that irrespective of the testing method employed, the mechanical strength properties exhibited a decline with an increase in the percentage of dammar in the hybrid resins, whereas the elasticity properties demonstrated an increase with this percentage. [ABSTRACT FROM AUTHOR]

This study measured the decrease in some mechanical properties of kraft paper used in packaging and bag production by examining the colour changes occurring in accordingly prepared standard samples subjected to UV influence. Thus, it is aimed to predict the mechanical properties of packages that have been exposed to sunlight over long periods of time with the colour change measurement, which is a non-destructive test, without the packaging deformation. Since there are mechanical differences between the cross-machine width and machine length of fabricated papers, these were measured separately. Measurements were made on papers exposed to UV for 0, 120, 240, 360, 480, 600, and 720 h. Tensile strength, strain at break, and tensile energy absorption (TEA) values were measured and also predicted for the kraft paper. For the prediction, the time and colour change values were used as independent variables, whereas the mechanical properties were taken as the dependent variables. The relationship between the time and colour change and the tensile strength, strain at break, and TEA variables in both the crossmachine and the machine directions were significant at the 5% level, and the R2 values were within acceptable limits. The results showed that the mechanical properties of the papers under UV effect decreased proportionally with the increase of the UV time. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Natural Fibers is the property of Taylor & Francis Ltd and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Polimery is the property of Industrial Chemistry Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Purpose: The paper aims to produce aluminium welds in the solid state with good specifications and the least amount of welding defects by using the friction stir welding method (FSW) and different tool pin profiles and welding parameters. The research investigated the mechanical characteristics and microstructure of a friction stir welded dissimilar aluminium alloy (2024-T3 to 7075-0) through thickness produced by varying welding settings and three different FSW tool pin shapes. Design/methodology/approach: The objective is to obtain the welds with the least amount of welding defects in the solid state by using the friction stir welding method (FSW), designing the tool pin profiles, and changing the rotation speeds. Findings: According to tensile strength and micro-hardness tests, tool rotation of 2000 rpm and square pin profile were the best compared to other working parameters. The greatest hardness and highest tensile strength of FSWed dissimilar aluminium joints have been 144 HV and 215 MPa, respectively, when using the square pin profile at a tool rotation speed of 2000 rpm. The hardness and tensile strength of FSWed dissimilar aluminium alloy joints increase with the tool rotation speed. Microstructural observations of the FSWed dissimilar aluminium joints using a square pin profile at the tool rotation speed of 2000 rpm exhibited the weld zone's high weld quality. Additionally, there were no defects in the weld zone. The fracture surface of the FSWed joint indicated a ductile fracture type. Research limitations/implications: With many regions on either side of the weld with varied compositions, microstructures, and characteristics, the resulting welds of dissimilar alloys might result in unsatisfactory weld joints. Practical implications: The weld zone's exceptional weld quality was demonstrated by microstructural investigations of the FSWed dissimilar aluminium connections utilising a square pin profile at a tool rotation speed of 2000 rpm and feed rate of 20 mm per minute. Application in aerospace, shipbuilding and marine, railway, construction, electrical industries, and land transportation. Originality/value: The original value of the paper is the production of welds from dissimilar aluminium alloy (2024-T3 to 7075-0) with the least amount of welding defects by changing the tool pin profiles and tool rotation speeds using the friction stir welding method. [ABSTRACT FROM AUTHOR]

Composite fibers are an essential component of modern concrete structures, providing enhanced mechanical properties and durability. There are different types of fibers commonly used in concrete such as steel, glass, carbon, polypropylene fibers, etc. Composite fibers include a combination of two or more of these fibers. Composite fibers are discussed in detail, along with their properties and benefits. This paper also highlights the effects of composite fibers on the various properties of concrete, such as compressive strength, tensile strength, toughness, and durability. Furthermore, this paper discusses some of the challenges and limitations associated with the use of composite fibers in concrete, including issues related to fiber dispersion, fiber--matrix interactions, and costeffectiveness. Finally, this paper concludes with a discussion of the future directions of research on composite fibers in concrete, focusing on potential advancements in fiber technology, improved manufacturing techniques, and the development of new fiber--matrix systems. Overall, this paper provides a comprehensive overview of the current state of the art in composite fibers in concrete and serves as a valuable resource for researchers and practitioners in the field. [ABSTRACT FROM AUTHOR]

Polylactic acid (PLA) is a biobased, biodegradable, non-toxic polymer widely considered for replacing traditional petroleum-based polymer materials. Being a semi-crystalline material, PLA has great potential in many fields, such as medical implants, drug delivery systems, etc. However, the slow crystallization rate of PLA limited the application and efficient fabrication of highly crystallized PLA products. This review paper investigated and summarized the influence of formulation, compounding, and processing on PLA's crystallization behaviors and mechanical performances. The paper reviewed the literature from different studies regarding the impact of these factors on critical crystallization parameters, such as the degree of crystallinity, crystallization rate, crystalline morphology, and mechanical properties, such as tensile strength, modulus, elongation, and impact resistance. Understanding the impact of the factors on crystallization and mechanical properties is critical for PLA processing technology innovations to meet the requirements of various applications of PLA. [ABSTRACT FROM AUTHOR]

Ultra-high-performance concrete (UHPC) is a cementitious composite combining high-strength concrete matrix and fiber reinforcement. Standing out for its excellent mechanical properties and durability, this material has been widely recognized as a viable choice for highly complex engineering projects. This paper proposes (i) the review of the influence exerted by the constituent materials on the mechanical properties of compressive strength, flexural tensile strength, and elastic modulus of UHPC and (ii) the determination of optimal quantities of the constituent materials based on simplified statistical analyses of the developed database. The data search was restricted to papers that produced UHPC with straight steel fibers at a content of 2% by volume. UHPC mixture models were proposed based on graphical analyses of the relationship of constituent materials versus mechanical properties, aiming to optimize the material's performance for each mechanical property. The results proved to be in accordance with the specifications present in the literature, characterized by high cement consumption, significant presence of fine materials, and low water-to-binder ratio. The divergences identified between the mixtures reflect how the constituent materials uniquely impact each mechanical property of the concrete. In general, fine materials were shown to play a significant role in increasing the compressive strength and flexural tensile strength of UHPC, while water and superplasticizers stood out for their influence on the material's workability. [ABSTRACT FROM AUTHOR]

Additive Manufacturing (AM) processes are known as revolutionary manufacturing processes that fabricate a part using a 3D model layer upon layer. These techniques gained more attention from various industries due to their advantages like low waste material. Also, these processes can produce any part with high degrees of complexity in a short period of time. The Fused Deposition Modeling (FDM) process is a material extrusion-based technique which works by extruding a fine molten polymeric filament through a heated nozzle on the heated platform named printer bed. In this method, some important manufacturing parameters play a crucial role in controlling the mechanical properties and quality of the final fabricated part. However, all printed specimens through the FDM process should be tested based on the standards under some critical circumstances. Thus, in the current research paper, five and three test speeds are considered in tensile and fracture testing procedures, respectively to evaluate how these speeds can affect the mechanical and mode I fracture properties. Also, as the FDM specimens present elastic–plastic behavior, the critical value of J-integral is assumed as a fracture assessment and calculated from the finite element analysis. Among the mechanical properties, ultimate tensile strength is affected significantly by the test speed. For instance, the ultimate tensile strength of FDM specimens is 39.02, 38.58, 42.33, 48.09, and 52.11 for test speeds of 2, 4, 6, 8, and 10 mm/min, respectively. But vice-versa results are detected for the mode I fracture behavior and corresponding values of J for the FDM-PLA specimens. Finally, experimental and numerical results together with comprehensive discussions about the considered speeds and obtained results are reported. [ABSTRACT FROM AUTHOR]

This paper investigates the preparation and properties of high-strength artificial blocks made from dredged silt with a clay content of 52.0%. A comparative analysis of the mechanical properties of dredged silt blocks produced using semi-dry pressing and vibration molding methods was conducted. The study examined the effects of using fly ash (FA) and ground granulated blast-furnace slag (GGBS) as substitutes for cement on the compressive strength, splitting tensile strength, and dry shrinkage of the blocks. Additionally, the microstructure of the dredged silt blocks was analyzed using scanning electron microscopy (SEM), mercury intrusion porosimetry (MIP), and thermogravimetric analysis. The results show that specimens prepared using the pressing method exhibit better mechanical performance with compressive and splitting tensile strength reaching 64.8 MPa and 5.6 MPa at 28 d, respectively, which increased by 111.07% and 143.48% compared to specimens prepared through vibration molding. The addition of FA and GGBS reduces the early strength of the block to a certain extent but without a significant adverse effect on later strength. GGBS demonstrates faster hydration and a better filling effect. The addition of GGBS or FA refines the pore structure and reduces the diameter of pores in the paste, which is beneficial for improving the dry shrinkage performance of the block. At 120 d, the dry shrinkage of blocks containing 50% FA and GGBS shows a reduction of 29.7% and 27.1%, respectively, compared to blocks made with cement. The properties of the silt blocks can be notably enhanced through mechanical force, particle gradation, and hydration action. The preparation of artificial blocks such as road bricks and ballast blocks using dredged soil as the main raw material has been applied in projects such as the Yangtze River waterway regulation in China and Skikda Port in Algeria. [ABSTRACT FROM AUTHOR]

Laser powder bed-fused Ti6Al4V alloy has numerous applications in biomedical and aerospace industries due to its high strength-to-weight ratio. The brittle α′-martensite laths confer both the highest yield and ultimate tensile strengths; however, they result in low elongation. Several post-process heat treatments must be considered to improve both the ductility behavior and the work-hardening of as-built Ti6Al4V alloy, especially for aerospace applications. The present paper aims to evaluate the work-hardening behavior and the ductility of laser powder bed-fused Ti6Al4V alloy heat-treated below (704 and 740 °C) and above (1050 °C) the β-transus temperature. Microstructural analysis was carried out using an optical microscope, while the work-hardening investigations were based on the fundamentals of mechanical metallurgy. The work-hardening rate of annealed Ti6Al4V samples is higher than that observed in the solution-heat-treated alloy. The recrystallized microstructure indeed shows higher work-hardening capacity and lower dynamic recovery. The Considère criterion demonstrates that all analyzed samples reached necking instability conditions, and uniform elongations (>7.8%) increased with heat-treatment temperatures. [ABSTRACT FROM AUTHOR]

Laser-directed energy deposition (LDED) provides a fast and environmentally friendly method for remanufacturing high-value engineering parts, but systematic research into the remanufacturing of 3D-damaged components is lacking. In this paper, LDED remanufacturing study of 3D-damaged components using 18Ni300 was conducted for the demand of high-quality repair of broken teeth of 42CrMo gears. First, reasonable process parameters were achieved through optimal matching of laser energy and powder feeding rate, and the microstructure and mechanical properties of the repaired and bonded regions of the simulated fractured tooth specimens were then systematically analyzed. The results show that the microstructure of the 3D remanufactured structure consists of discrete α-Fe dendrites with light-colored reticular γ-Fe and the presence of granular precipitation phase Ni3(Ti, Mo) in reticular γ-Fe. The hardness of the remanufactured tooth is 396.35 ± 10.11 HV0.2. The tensile strength at the bonding interface reached 102.21% of that of the substrate, and the plasticity is essentially similar. The tensile strength of the remanufactured structure in the scanning direction reaches 135.62% of that of the substrate, and the plasticity is increased by 26.62% compared to the matrix. The bending strength at the junction reaches 103.11% of the substrate and 107.75% of the substrate in the remanufactured region. The mechanical properties and three-dimensional dimensions of the remanufactured tooth basically meet the repair requirements, which can significantly extend the service life of the gear. The research in this paper provides a useful reference for laser additive remanufacturing of 3D-damaged structural parts. [ABSTRACT FROM AUTHOR]

Waterborne polyurethane asphalt emulsion (WPUA) is an environmentally friendly bituminous material, whose performance is highly dependent on the phase structure of the continuous phase. In this paper, WPUAs in the vicinity of phase inversion were prepared using waterborne polyurethane (WPU) and asphalt emulsion. The chemical structures, thermal stability, dynamic mechanical properties, phase-separated morphology and mechanical performance of WPUAs were studied. Fourier-transform infrared (FTIR) spectra revealed that there are no –NCO bonds in either the pure WPU or WPUAs. Moreover, the preparation of WPUA is a physical process. The addition of WPU weakens the thermal stability of asphalt emulsion. WPU improves the storage modulus of asphalt emulsion at lower and higher temperatures. The glass transition temperatures of the WPUA films are higher than that of the pure WPU film. When the WPU concentration increases from 30 wt% to 40 wt%, phase inversion occurs; that is, the continuous phase shifts from asphalt to WPU. The WPUA films have lower tensile strength and toughness than the pure WPU film. However, the elongations at break of the WPUA films are higher than that of the pure WPU film. Both the tensile strength and toughness of the WPUA films increase with the WPU concentration. Due to the occurrence of phase inversion, the elongation at break, tensile strength and toughness of the WPUA film containing 30 wt% WPU are increased by 29%, 250% and 369%, respectively, compared to the film with 40 wt% WPU. [ABSTRACT FROM AUTHOR]

This paper deals with the austempering of ductile iron (ADI) and clarifies the influential austempering parameters during the production of ADI. During the austempering process, the heat treatment parameters can be varied, thus influencing the final microstructure and, of course, the mechanical properties of ADI. To appropriately conduct experiments and obtain good results, an experimental plan was developed using the Design Expert 13 software. Along with the heat treatment parameters, the influence of the copper content on the ADI toughness, tensile strength, and elongation was determined. The obtained results from this experiment were used to develop unique mathematical models which describe the influences of heat treatment and copper content on the observed mechanical properties of ADI samples. These mathematical models can be applied to predict the analysed mechanical properties of ADI in the dependence of heat treatment parameters and copper content in base ductile iron. For the multi response optimisation of toughness, tensile strength, and elongation, a hybrid grey-fuzzy technique was presented as a significant contribution to the enhancement of the analysed mechanical properties. Consequently, the copper content and heat treatment parameter levels that resulted in the maximal mechanical properties' functions were defined. [ABSTRACT FROM AUTHOR]

The primary focus of the current paper centers on the microstructures and mechanical properties exhibited by a Ti-30Nb-12Zr-5Ta-2Sn-1.25Fe (wt. %) (TNZTSF) alloy that has been produced through an intricate synthesis process comprising cold-crucible induction in levitation, carried out in an atmosphere controlled by argon, and cold-rolling deformation (CR), applying systematic adjustments in the total deformation degree (total applied thickness reduction), spanning from 10% to 60%. The microstructural characteristics of the processed specimens were investigated by SEM and XRD techniques, and the mechanical properties by tensile and microhardness testing. The collected data indicate that the TNZTSF alloy's microstructure, in the as-received condition, consists of a β-Ti phase, which shows polyhedral equiaxed grains with an average grain size close to 82.5 µm. During the cold-deformation processing, the microstructure accommodates the increased applied deformation degree by increasing crystal defects such as sub-grain boundaries, dislocation cells, dislocation lines, and other crystal defects, powerfully affecting the morphological characteristics. The as-received TNZTSF alloy showed both high strength (i.e., ultimate tensile strength close to σUTS = 705.6 MPa) and high ductility (i.e., elongation to fracture close to εf = 11.1%) properties, and the computed β-Ti phase had the lattice parameter a = 3.304(7) Å and the average lattice microstrain ε = 0.101(3)%, which are drastically influenced by the applied cold deformation, increasing the strength properties and decreasing the ductility properties due to the increased crystal defects density. Applying a deformation degree close to 60% leads to an ultimate tensile strength close to σUTS = 1192.1 MPa, an elongation to fracture close to εf = 7.9%, and an elastic modulus close to 54.9 GPa, while the computed β-Ti phase lattice parameter becomes a = 3.302(1) Å. [ABSTRACT FROM AUTHOR]

The early strength of geopolymers (GPs) and their composites is higher, and the hardening speed is faster than that of ordinary cementitious materials. Due to their wide source of raw materials, low energy consumption in the production process, and lower emissions of pollutants, they are considered to have the most potential to replace ordinary Portland cement. However, similar to other inorganic materials, the GPs themselves have weak flexural and tensile strength and are sensitive to micro-cracks. Improving the toughness of GP materials can be achieved by adding an appropriate amount of fiber materials into the matrix. The use of discrete staple fibers shows great potential in improving the toughness of GPs. Sisal is a natural fiber that is reproducible and easy to obtain. Due to its good mechanical properties, low cost, and low carbon energy usage, sisal fiber (SF) is a GP composite reinforcement with potential development. In this paper, the research progress on the effect of SF on the properties of GP composites in recent decades is reviewed. It mainly includes the chemical composition and physical properties of SFs, the preparation technology of sisal-reinforced geopolymers (SFRGs), the microstructure analysis of the interface of SFs and the GP matrix, and the macroscopic mechanical properties of SFRGs. The properties of SFs make them have good bonding properties with the GP matrix. The addition of SFs can improve the flexural strength and tensile strength of GP composites, and SFRGs have good engineering application prospects. [ABSTRACT FROM AUTHOR]

The traditional preparation process of natural rubber latex requires tedious treatment of a variety of rubber additives. In this paper, a new process of wet mixed grinding was used to prepare a reinforced vulcanization mixture and a rapid vulcanization effect. The effect of different amounts of vulcanization mixtures on the mechanical properties of natural latex film was studied, and the pre-vulcanization process of latex and the vulcanization process of film were optimized. The results showed that with the increase in the amount of vulcanization mixture, the tensile strength increased from 5.96 MPa to 29.28 MPa, and the tear strength increased from 7.59 kN/m to 52.81 kN/m. When the vulcanization temperature of the latex film is heated from 80 °C to 100 °C, the vulcanization time is shortened by 5~6 times. The new vulcanization mixture prepared in this work has the characteristics of simple production and fast vulcanization speed, which provides a new solution for the development of the latex product industry. [ABSTRACT FROM AUTHOR]

17-4PH Stainless Steel is a mechanically high-performing alloy that is widely used across chemical and mechanical processing industries. The alloy is conventionally fabricated by cast methods, but emerging additive manufacturing techniques are presently offering an economic, efficient, and environmentally friendly alternative. Bound Powder Extrusion (BPE) is a relatively new additive manufacturing technique that is used to fabricate three-dimensional, free-form components. Investigation into the mechanical properties and behavior of 17-4PH stainless steel fabricated by BPE is vital to understanding whether this technique proposes a competitive substitute to the cast alloy within industry. Published literature has investigated the as-fabricated mechanical properties, microstructure, porosity, and post-processing heat treatment of the BPE alloy, with limited comparison evident among the papers. This paper, therefore, aims to review published findings on the mechanical properties of 17-4PH stainless steel produced by additive manufacturing techniques, with a key focus on BPE. It is important to highlight that this review study focuses on the MetalXTM 3D printer, manufactured by Markforged. This printer is among the widely utilized BPE 3D printers available in the market. The key results, together with the impact of post-heat treatments, were discussed and compared to provide a more comprehensive picture of the patterns that this alloy presents in terms of its microstructure and mechanical properties. This enables the manufacture of components relative to desired material performance, improving overall functionality. A comparison of yield strength, ultimate tensile strength (UTS), Young's modulus, ductility, and hardness was made relative to microstructure, porosity, and density of published literature for the as-fabricated and post-heat-treated states, identifying areas for further research. [ABSTRACT FROM AUTHOR]

Several studies have shown the potential of strain-hardening cementitious composites (SHCC) as a self-reinforcing printable mortar. However, papers published on the development of three-dimensional printable SHCC (3DP-SHCC) often report a discrepancy between the mechanical properties of the cast and printed specimens. This paper evaluates the effect of each successive phase of the printing process on the mechanical properties of the composite. To this end, materials were collected at three different stages in the printing process, i.e., after each of mixing, pumping, and extruding. The collected 3DP-SHCC materials were then cast in specimen moulds and their mechanical properties after curing were obtained. The resulting findings were juxtaposed with the mechanical properties of the specimens derived from a fully printed 3DP-SHCC element, and our findings indicate that while the density and the compressive strength are not significantly influenced by the printing process, the flexural and tensile strength, along with their associated deflection and strain, are strongly affected. Additionally, this research identifies the pumping phase as the primary phase influencing the mechanical properties during the printing process. [ABSTRACT FROM AUTHOR]

The utilization of Al2O3 nanopowder to reinforce AA5754 aluminum alloy through blind holes employing the friction stir processing (FSP) technique to produce an aluminum matrix nanocomposite is explored in this paper. Motivated by the necessity to enhance the strength and ductility of welded joints, the impacts of varying the tool rotational speed (rpm) and blind hole diameter on the microstructure and mechanical properties of the joints are investigated. Experimental characterization techniques including SEM, optical microscopy, microhardness, and tensile tests were employed to analyze the welded joints produced under different processing parameters (tool rotational speeds of 910, 1280, and 1700 rpm, and blind hole diameters of 0, 1, 1.5, and 2 mm). Comparative analyses were conducted against base metal properties and joints without reinforcement powder. It was found that the addition of nanopowder resulted in a decrease in the maximum generated heat during FSP, while also reducing the stir zone size compared to samples without nanopowder. Moreover, enhancements in both the strength and ductility of the joints were observed with the incorporation of Al2O3 nanoparticles. The optimal combination of welding conditions, observed at 1280 rpm rotational speed and 1.5 mm hole diameter, yielded a remarkable ultimate tensile strength of 567 MPa, accompanied by a hardness of 45 HV. These results underscore the potential of nano-Al2O3 reinforcement in significantly improving the mechanical properties of the produced nanocomposite, with implications for advancing the performance of welded structures in various engineering applications. [ABSTRACT FROM AUTHOR]

The feasibility of manufacturing high-performance components with complex structures is limited due to cracks in some superalloys fabricated by selective laser melting (SLM). By controlling the main process parameters such as scanning strategy, the adverse effects of cracks can be effectively reduced. In this paper, the effects of two different SLM scanning strategies with island and 'back-and-forth' and post-heat treatment on the cracks and mechanical properties of selective-laser-melted (SLMed) K438 alloy were investigated. The results show that the SLM method of the 'back-and-forth' scanning strategy had better lap and interlayer rotation angles and a more uniform distribution of laser energy compared with the island scanning strategy. The residual stress accumulation was reduced and crack formation was inhibited under this scanning strategy owing to the cooling and shrinkage process. In addition, the dislocation motion was hindered by the formation of uniformly dispersed MC carbides and γ' phases during the SLM K438 alloy process, which resulted in the density of the as-built SLMed K438 alloy being up to 99.34%, the hardness up to 9.6 Gpa, and the tensile strength up to 1309 MPa. After post-heat treatment, the fine secondary γ' phases were precipitated and dispersed uniformly in the Ni matrix, which effectively improved the Young's modulus and tensile strength of the alloy by dispersing the stress-concentrated area. [ABSTRACT FROM AUTHOR]

In this paper, the electron backscatter diffraction (EBSD) technique was used to analyze the dynamic recrystallization (DRX), twinning, slip behavior, and texture evolution during forging and subsequent extruding deformation. The results show that, as the degree of strain increased (forging to extruding), the degree of DRX increased, and the DRX mechanism changed from discontinuous DRX (DDRX) during forging to DDRX and continuous DRX (CDRX) during extruding. Particle stimulation nucleation (PSN) promoting DRX occurred during deformation. The deformation process mainly produced {10–12} twins (TTW) and played a role in coordinating the deformation. The slip behavior also changed according to an analysis of in-grain misorientation axes (IGMA) results, changing from slip-dominated with a basal slip to co-dominated with multiple slip modes, with the activation of mainly prismatic and pyramidal slip. Meanwhile, the strong basal texture at the beginning of the deformation also changed, and the texture strength decreased from 24.81 to 15.56. The weakening of the texture was mainly due to the formation of DRX grains and twins, as the newly formed DRX and twins reoriented. In the later stages of deformation, the activation of prismatic slip and pyramidal slip changed the basal texture component. Based on microstructural analysis, the improvement in mechanical properties was due to fine-grain strengthening and load-transfer strengthening. The ultimate tensile strength (UTS) was 370.5 MPa, the yield strength (YS) was 340.1 MPa, and the elongation (EL) was 15.6%. [ABSTRACT FROM AUTHOR]

The study and utilization of fully recycled aggregate concrete (FRAC), in which coarse and fine aggregates are completely replaced by recycled aggregates, are of great significance in improving the recycling rate of construction waste, reducing the carbon emission of construction materials, and alleviating the ecological degradation problems currently faced. In this paper, investigations were carried out to study the effects of steel fiber (0.5%, 1.0%, and 1.5%) and polypropylene fiber (0.9 kg/m3, 1.2 kg/m3 and 1.5 kg/m3) on the properties of FRAC, including compressive strength, splitting tensile strength, the splitting tensile load–displacement curve, the tensile toughness index, flexural strength, the load–deflection curve, and the flexural toughness index. The results show that the compressive strength, splitting tensile strength, and flexural strength of fiber-reinforced FRAC were remarkably enhanced compared with those of ordinary FRAC, and the maximum increase was 56.9%, 113.3%, and 217.0%, respectively. Overall, the enhancement effect of hybrid steel–polypropylene fiber is more significant than single-mixed fiber. Moreover, the enhancement of the crack resistance, tensile toughness, and flexural toughness obtained by adding steel fiber to the FRAC is more significant than that obtained by adding polypropylene fiber. Furthermore, adding polypropylene fiber alone and mixing it with steel fiber showed different FRAC splitting tensile and flexural properties. [ABSTRACT FROM AUTHOR]

Introducing Neutral Polymeric bonding agents (NPBA) into the Nitrate Ester Plasticized Polyether (NEPE) propellant could improve the adhesion between filler/matrix interface, thereby contributing to the development of new generations of the NEPE propellant with better mechanical properties. Therefore, understanding the effects of NPBA on the deformation and damage evolution of the NEPE propellant is fundamental to material design and applications. This paper studies the uniaxial tensile and stress relaxation responses of the NEPE propellant with different amounts of NPBA. The damage evolution in terms of interface debonding is further investigated using a cohesive-zone model (CZM). Experimental results show that the initial modulus and strength of the NEPE propellant increase with the increasing amount of NPBA while the elongation decreases. Meanwhile, the relaxation rate slows down and a higher long-term equilibrium modulus is reached. Experimental and numerical analyses indicate that interface debonding and crack propagation along fillerematrix interface are the dominant damage mechanism for the samples with a low amount of NPBA, while damage localization and crack advancement through the matrix are predominant for the ones with a high amount of NPBA. Finally, crosslinking density tests and simulation results also show that the effect of the bonding agent is interfacial rather than due to the overall crosslinking density change of the binder. [ABSTRACT FROM AUTHOR]

The use of wood in outdoor conditions is of great importance for the service life of wood, and the process of thermal modification (TM) directly affects the effective value of wood products. This paper presents theoretical and experimental studies of the parameters influencing TM of wood on the changes of its physical and mechanical properties. Experimental studies were performed on thermally modified wood samples for different values of the influential parameters of thermal modification: T (°C), t (h) and ρ (g·cm–3), while the tensile strength was obtained as the output parameter. The obtained experimental data were stochastically modelled and compared with the model obtained by genetic programming. The optimization of processing parameters was performed by classical mathematical analysis and compared with the results obtained by optimization with genetic algorithm. The results of the optimal design parameters obtained by different approaches to optimization were compared and based on that the analysis of the characteristics of the presented techniques was conducted. [ABSTRACT FROM AUTHOR]

WIt has great environmental potential to replace natural aggregates by recycled brick aggregates. To investigate the deterioration mechanism of recycled brick aggregate concrete, this paper designed eight groups of recycled brick aggregate sub-lightweight concrete with different water-cement ratios, maximum aggregate sizes and coarse aggregate type ratios, and carried out mechanical property test to analyze the aggregate interface characteristics and the damage mechanism of recycled brick aggregate concrete. The results show that the increase of replacement ratio and water-cement ratio leads to a significant decrease of compressive strength and splitting tensile strength of concrete, and the influence of the maximum aggregate size on strength is small. Unlike the recycled concrete aggregate - mortar interface, the microstructure of recycled brick aggregate - mortar interface is dense and the interface performance is enhanced. Recycled brick aggregate concrete is in non-interface damage mode, and the strength of brick aggregate is the main influence to determine the mechanical properties of concrete factor. [ABSTRACT FROM AUTHOR]

Titanium alloy components often experience damage from impact loads during usage, which makes improving the mechanical properties of TC4 titanium alloys crucial. This paper investigates the influence of laser scanning irradiation on the tensile properties of thin titanium alloy sheets. Results indicate that the tensile strength of thin titanium alloy sheets exhibits a trend of initial increase followed by a decrease. Different levels of enhancement are observed in the elongation at break of a cross-section. Optimal improvement in the elongation at break is achieved when the laser fluence is around 8 J/cm2, while the maximum increase in tensile strength occurs at approximately 10 J/cm2. Using femtosecond laser surface irradiation, this study compares the maximum enhancement in the tensile strength of titanium alloy base materials, which is approximately 8.54%, and the maximum increase in elongation at break, which reaches 25.61%. In addition, the results verify that cracks in tensile fractures of TC4 start from the middle, while laser-induced fracture cracks occur from both ends. [ABSTRACT FROM AUTHOR]

In this paper, the evolution of the microstructure, mechanical properties, and intergranular corrosion (IGC) resistance of an Al-Mg-Si-Ag alloy is systematically investigated. For the as-cast alloy, the microstructure consists of the Mg2Si phase and Mg32(Al, Ag)49 phase. In the isothermal aging process, the novel alloy presents a significant age hardening effect. The ultimate tensile strength (UTS) and yield strength (YS) of the peak-aged alloy are 342 MPa and 231 MPa, respectively, which are 53 MPa and 84 MPa higher than that of the as-quenched alloy. The main strengthening phase at the peak-aged stage of the alloy is the MgAg phase, which has a body-centered cubic structure with a lattice constant of a = 0.33 nm. In addition, the IGC resistance of the peak-aged alloy is worse than that of other aged alloys. The corresponding microstructure of GBPs of the peak-aged alloy is more consecutive, and this is the main reason for the deterioration of IGC resistance of the alloy. [ABSTRACT FROM AUTHOR]

This paper presents the results of physical modelling of the process of multi-pass rolling of a wire rod with controlled, multi-stage cooling. The main goal of this study was to verify the possibility of using a torsion plastometer, which allows conducting tests on multi-sequence torsion, tensile, compression and in the so-called complex strain state to physically replicate the actual technological process. The advantage of the research methodology proposed in this paper in relation to work published so far, is its ability to replicate the entire deformation cycle while precisely preserving the temperature of the deformed material during individual stages of the reproduced technological process and its ability to quickly and accurately determine selected mechanical properties during a static tensile test. Changes in the most important parameters of the process (strain, strain rate, temperature, and yield stress) were analyzed for each variant. After physical modelling, the material was subjected to metallographic and hardness tests. Then, on the basis of mathematical models and using measurements of the average grain size, chemical composition, and hardness, the yield strength, ultimate tensile strength, and plasticity reserve were determined. The scope of the tests also included determining selected mechanical properties during a static tensile test. The obtained results were verified by comparing to results obtained under industrial conditions. The best variant was a variant consisting of physically replicating the rolling process in a bar rolling mill as multi-sequence non-free torsion; the rolling process in an NTM block (no twist mill) as non-free continuous torsion, with the total strain equal to the actual strain occurring at this stage of the technological process; and the rolling process in an RSM block (reducing and sizing mill) as tension, while maintaining the total strain value in this block. The differences between the most important mechanical parameters determined during a static tensile test of a wire rod under industrial conditions and the material after physical modelling were 1.5% for yield strength, approximately 6.1% for ultimate tensile strength, and approximately 4.1% for the relative reduction of the area in the fracture and plasticity reserve. [ABSTRACT FROM AUTHOR]

Polypropylene is a useful and widely consumed thermoplastic with very good properties that can be mixed with a combination of rubber and nanoparticles in order to eliminate its shortcomings. In this paper, the simultaneous combination of both the toughening effect of styrene–butadiene rubber (SBR) and the reinforcing effect of silicon carbide (SiC) nanoparticles were investigated in polypropylene matrix. Mechanical properties (tensile and impact strength [TS and IS]) of compounds were analyzed using the central composite design approach in Design‐Expert software. With two factors for input variables of SBR and SiC weight percentages, and their five levels (5, 10, 15, 20, and 25) and (0, 1.5, 3, 4.5, and 6), respectively, the central composite design approach employs 11 experiments for creation of models and the analysis of variance investigations with two output responses of TS and IS. Statistical results revealed that SBR and SiC contents had a significant effect on TS, IS, and the microstructure of compounds, as confirmed by scanning electron microscopy and energy‐dispersive spectroscopy images. To maximize all mechanical properties simultaneously with desirability functions, TS and IS of the optimum sample were computed to be 21.98 MPa and 8.66 kJ/m2 in amounts of 13.45 and 2.80 weight percentage (wt%) of SBR and SiC, respectively. Highlights: By increasing silicon carbide (SiC) in polypropylene/styrene–butadiene rubber (SBR), tensile strength decreases after a peak due to agglomeration effect.By increasing SiC in polypropylene/SBR, impact strength decreases after a peak due to agglomeration effect.By increasing SiC, the rubber particles' dimensions decrease according to scanning electron microscopy analysis.Simultaneous maximum of tensile strength and impact strength are 21.98 MPa and 8.66 KJ/m2, respectively.Optimum value of SBR and SiC in above maximums are 13.45 and 2.8 wt%, respectively. [ABSTRACT FROM AUTHOR]

This paper employs OM, XRD, EBSD and mechanical properties testing to investigate the influence of shot peening on the microstructure and mechanical properties of 3D-printed 316L stainless steel. The following explores changes in the microstructure and mechanical properties of 316L stainless steel by 3D printing with different forming angles after shot peening: (1) As the forming angle increased from 0° to 90°, the microstructure of 3D-printed 316L stainless steel became significantly refined, and the thickness of ultrafine microstructure in the surface layer increased from 5 to 70 μm; (2) the hardness of the material increased from 471 HV to 482 HV as the forming angle increased from 0° to 90°; (3) According to the EBSD results, the enhanced hardness was attributed to refinement hardening and dislocation hardening. Moreover, the maximum yield strength (YS), ultimate tensile strength (UTS), and tensile elongation (TE) of 845, 862 MPa, and 17.8%, respectively, were obtained when the forming angle was 90°. [ABSTRACT FROM AUTHOR]

As a by-product of bamboo processing, bamboo powder is incinerated or buried due to its ineffective utilization, which contributes to pollution. The large amount of waste bamboo powder generated during the processing of bamboo products cannot be effectively utilized. Meanwhile, multiple recycling leads to the loss of fiber quality of corrugated cardboard (OCC) pulp, reducing the mechanical properties of paper. In an effort to obtain high value from waste bamboo powder, this study pulped it using the kraft process. Scanning electron microscope (SEM) observations showed that the surface of bamboo fiber had more cracks, which made bamboo fiber have better air permeability. The permeability of bamboo paper was 146% that of the OCC. X-ray diffraction (XRD) analysis showed that the crystallinity of bamboo pulp was 133% that of the OCC pulp. The results of physical testing of paper showed that the tensile strength of bamboo paper was 116% that of the OCC. The tear strength of bamboo paper was 61.7% that of the OCC, and the bursting strength of bamboo paper was 59.1% that of the OCC. Based on the above results, bamboo powder can be used as raw material for making OCC pulp. [ABSTRACT FROM AUTHOR]

Molecular dynamics (MD) simulations permit copying methodical differences of mechanical and interfacial properties outside the scope of experimental approaches. This paper reviews the effect of graphene on the mechanical properties such as Young's modulus, shear modulus, ultimate tensile strength and Young's modulus of epoxy nanocomposites via MD simulations. In MD simulation arrangement, the computational techniques are studied for dissimilar qualities of mixing a polymer matrix with graphene as the nanofiller. Subsequently, numerous papers are discussed involving graphene and its polymer nanocomposites. Furthermore, advances in molecular modeling, simulation of graphene and their nanocomposites are deliberated by considering feature charge graphene assemblies, aspect ratio, weight fraction, atomic density, molecular energy and density effect as the primary factors. It was concluded from investigations that their mechanical properties as well as interfacial properties are suitable for scientific applications. [ABSTRACT FROM AUTHOR]

The effects of Mn addition on the room temperature tensile strength and deformation mechanisms of as-cast Mg-8Al-1Nd-1.5Gd-xMn alloys (x = 0, 0.3, 0.5, 1.0 wt.%) are investigated in this paper. The results indicate that the addition of Mn contributes to the precipitation of Al-Mn-RE intermetallics and the refinement of α-Mg matrices, thereby improving the tensile strength of the 1.0 Mn alloy at 190 MPa. The fracture mechanism of Mn-containing alloys transforms from a cleavage fracture to a ductile fracture as the Mn content increases from 0.3 to 1.0 wt.%. The presence of intermetallic particles in the dimples confirms the hindrance effect of Al10Mn2 (Nd,Gd) on dislocation slips. The novel technology of in-grain misorientation axes (IGMAs) is used to identify activated slip modes and deformation twins. It can be concluded that the activated pyramidal slip during tensile deformation significantly promotes the ductility of the 1.0 Mn alloy with an elongation rate of 9.8%. It is worth noting that reducing the coarse 10 1 ¯ 2 tensile twins and enhancing the proportion of 10 1 ¯ 1 compressive twins and 10 1 ¯ 1 - 10 1 ¯ 2 double twins contributes to maintaining the continuous plastic deformation of Mg alloy. [ABSTRACT FROM AUTHOR]

Inconel718 maintains excellent mechanical properties at high temperatures of 700 ℃ and has a wide range of applications in aerospace, high-performance turbines, and other fields. However, the use of improper laser process parameters makes the Inconel718 obtained by the directional energy deposition method have poor performance and defects, and there are currently fewer studies on the regulation of the mechanical properties of the preparation of Inconel718 by directed energy deposition. In this paper, the influencing regulation of laser process parameters of laser power, scanning speed, hatch spacing, layer thickness, and forming direction on the microstructure and mechanical properties of Inconel718 prepared by directional energy deposition is investigated by single-factor test method. The mechanical properties of Inconel718 obtained by directional energy deposition and forge are compared. The results show that, among the five laser process parameters, the laser power and forming direction have significant effect on the mechanical properties of Inconel718 obtained by directional energy deposition, while the scanning speed, scanning spacing, and layer thickness have less influence on its mechanical properties. Compared with Inconel718 prepared by ordinary forge, the tensile strength of Inconel718 obtained by directed energy deposition is reduced by 7.64%, the hardness is increased by 23.55%, the impact strength is reduced by 17.6%, and the plasticity is reduced obviously. Good mechanical properties can be reached from the Inconel718 obtained by the directional energy deposition method. [ABSTRACT FROM AUTHOR]

In this paper, a disk laser welding was developed to join 3-mm thin-Sect. 30Cr3 ultra-high-strength steel which was widely used in aerospace. The microstructure and mechanical properties of welded joint were investigated in detail. The results indicated that the recommended laser linear energy range were between 150 and 165 J/mm to guarantee that the melting width was up to 1 mm as well as less oxidation, spatter, and depression on the weld. Meanwhile, for the as-welded (AW) condition, the base metal (BM) consisted of ferrite matrix with distributing small spherical carbides, also known as spherical pearlite. While, the fine grained region, coarse grained region, and weld metal were all composed of martensite. However, the partially transformed region mainly consisted martensite with a little of spherical pearlite. Meanwhile, the average grain sizes of weld metal, HAZ, and base metal were 1.3 μm, 1.5 μm, and 1.8 μm, respectively. However, for the post-weld heat treatment (PWHT) condition, the whole welded joint was all composed of tempered martensite, and the average grain size of welded joint was about 1.7 μm. The tensile strength of the welded joint was higher than that of the base metal both in the AW and PWHT condition as all the fracture with shrinkage occurred in the BM of the specimens. Additionally, the average yield strength of the AW and PWHT are about 600 MPa and 1700 MPa, respectively. [ABSTRACT FROM AUTHOR]

In this paper, the effectiveness of the strengthening by a wooden plate for reinforced concrete (RC) beams that incorporate waste sawdust (SD) as a partial substitute for fine aggregate (sand) has been investigated. To this end, two types of concrete mixtures were made: normal concrete (NC) and sawdust concrete (SDC), which was made by substituting 15% of the volume of sand with SD. Five RC beams (100 mm in depth, 200 mm in width, and 1500 mm in length) were experimentally tested for flexural behavior under four-point loading. Three strengthening schemes were used in this study. The first scheme used a wooden plate that was only fixed by an adhesive layer. The second and third schemes were applied by a wooden plate, which was fixed by an adhesive layer and steel angles (two and eleven angles). The findings of the study indicate that although the concrete's workability, compressive, and splitting tensile strengths were reduced with the addition of SD, the ultimate load of the beam with SD was lower than that of the control beam, with a slight variation of approximately 4%. Moreover, strengthening the RC beam with a wooden plate and two steel angles yielded the highest load capacity among all tested beams, 20% higher than the control specimen. The study's findings offered useful information for developing eco-friendly sawdust concrete beams with efficient strengthening techniques for potential future uses. [ABSTRACT FROM AUTHOR]

Palm leaf manuscripts were a prevalent literary medium from South Asia and Southeast Asia prior to the widespread use of paper. This study focuses on the analysis of historical palm leaf manuscripts from South and Southeast Asia. Sample palm leaf manuscripts from Burma were used as a case study; simulated palm leaf manuscripts were also created as a reference for comparison. The anatomy, chemical composition, and mechanical properties of the manuscripts were analyzed to find various forms of deterioration, including damage, fractures, pollution, acidification, and microbial deterioration. Specifically, the S1–S3 layers of the cell walls exhibited complete cracking, and the S2 layer showed numerous circular or nearly circular cavities caused by microbial erosion, while the middle lamella remained intact. The severe degradation of polysaccharides and pectin, accompanied by an increase in the relative content of lignin, caused the historical manuscripts to become more brittle. Additionally, the tensile strengths of historical palm leaf manuscripts were markedly reduced; their longitudinal tensile strength was significantly greater than their transverse tensile strength. This study can contribute to a better understanding of the deterioration process of historical palm leaf manuscripts and provide valuable insights for their restoration and preservation. [ABSTRACT FROM AUTHOR]

Reasonable welding speeds are a prerequisite for obtaining high-quality joints by friction stir welding (FSW). In this paper, 2195-T8 Al-Li alloy FSW joints were successfully fabricated at different welding speeds (100–600 mm/min) with a constant rotation speed. The effect of welding speed on the microstructure and mechanical properties was analyzed under different experimental methods. Microstructural characterization was conducted using optical microscopy (OM), scanning electron microscopy (SEM), electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM). Mechanical properties were measured by a hardness test and a tensile test. The results showed that the original T1 precipitates disappeared in the nugget zone (NZ), generating many dislocations. With welding speeds increasing, joints obtained at lower welding speeds developed coarser T1 precipitates in the heat-affected zone. Also, the equiaxed grains with a bigger size and a higher fraction of high angle boundaries (HABs) were detected in the NZ of these joints. As the welding speed increased, the area of hardness value changes gradually shrunk, which was consistent with the trend of the cross-section morphology. A kissing bond and macroscopic cracking were observed in the joints that were fabricated at the higher welding speeds. The appearance of those defects significantly reduced the ultimate tensile strength and elongation of the joints at high welding speeds. Fracture morphologies of the different joints were all characterized in quasi-cleavage fractures. [ABSTRACT FROM AUTHOR]

Hardwoods commonly have high mechanical properties, which makes them interesting for structural use, but softwoods dominate the structural timber market in Europe. Tensile strength classes are recommended for engineered wood products. However, current European standards do not provide tensile strength classes for hardwoods and the declaration of tensile properties from machine grading in the industry is not yet possible. The present paper aims to contribute to the revision of European standards through the technical group CEN/TC124/WG2/TG2: Tensile strength classes for hardwoods, of the European Standardisation Committee. An experimental campaign which involved machine grading and tensile testing of over 569 boards of Southern blue gum (Eucalyptus globulus Labill.) from Spain and Portugal was made. Six new tensile strength classes were defined, from ET24 (ft,0,k = 24 N/mm2, Et,0,m = 18 kN/mm2 and ρk = 590 kg/m3) to ET42 (ft,0,k = 42 N/mm2, Et,0,m = 23 kN/mm2 and ρk = 640 kg/m3). Machine grading made possible the definition of six strength class combinations. Four combinations resulted in 40% of the sample being assigned to the higher strength class, with low percentages of rejection (varying between 1% and 14%). This demonstrates the high mechanical properties of the species and the performance improvement of machine grading with respect to current visual grading. [ABSTRACT FROM AUTHOR]

Previous studies have confirmed that for cemented tailings backfill, mechanical properties are improved through the addition of fiber. However, for fiber-reinforced cemented sulfur tailings backfill (FRCSTB), physical and flow properties are still unknown. In this paper, the changes in fluidity, splitting tensile strength (STS) and uniaxial compressive strength (UCS) of cemented sulfur tailings backfill (CSTB) are analyzed in detail. Secondly, regarding the addition of glass fiber and polypropylene fiber, the changes in the fluidity, STS and UCS of the CSTB, resulting from the fiber length, fiber content and method of fiber addition used, were analyzed. Moreover, the relationship between the UCS and fiber content is established. Finally, the mechanism behind the influence of fiber and sulfur content on the mechanical properties of CSTB is revealed. The results indicate that with the increase in sulfur content, the fluidity of the tailings slurry exhibits exponential growth. During the process of increasing sulfur content, the UCS and STS of CSTB initially increase and then decrease, reaching maximum values at 12% sulfur content. Similarly, at a fiber content of 0.6%, the UCS and 28d STS of CSTB reach their maximum values. In terms of enhancing the mechanical properties of CSTB, the effectiveness of glass fibers surpasses that of polypropylene fibers. In addition, regarding the improvement of the UCS of CSTB, the mixed addition of fibers is obviously worse than that of fiber alone. However, in terms of enhancing the STS of CSTB, the mixed addition of fibers outperforms the single addition of polypropylene fiber. From a microscopic perspective, polypropylene and glass fiber are able to form strong cohesion with the cement–tailings matrix and effectively prevent the formation and expansion of pores and cracks. [ABSTRACT FROM AUTHOR]

In this paper, the post-weld explosive hardening of a 5 mm AA7075-T651 plate welded via FSW was performed. To investigate the possibility of increasing FSW joint mechanical properties, the welded plate was explosively treated with four various explosive materials (ammonal, emulsion explosive, FOX-7, and PBX) in two different hardening systems. As part of the investigation, the observations of the surface and macrostructure of the treated plates were described. The obtained microhardness distribution allowed us to register the increase in hardness of the SZ up to 6%, but no increase in hardness of the LHZ was reported. In most cases, the influence of explosive treatment on the mechanical properties of the welded joint was disadvantageous as ultimate tensile strength and ductility were reduced. The only positive effect which was observed is the increase in the value of yield strength up to 27% corresponding to 77 MPa, achieved by explosive materials with detonation velocity below 3000 m/s. [ABSTRACT FROM AUTHOR]

The stratospheric airship, a long-term floating vehicle in near-space, has become a new hotspot in aerospace exploration. The airship's envelope material is vulnerable to ozone exposure in near-space and degrades. This paper used typical Kevlar fiber as the research material for an ozone exposure experiment in a near-space simulated environment. The results showed that the elongation of the Kevlar fiber decreased and the elastic modulus increased after ozone exposure. The tensile strength of fiber decreased gradually with an increase in ozone concentration and exposure time. When ozone concentration increased from 0 pphm to 1000 pphm, the tensile strength of fiber decreased from 2397 MPa to 2059 MPa. With increasing ozone exposure time from 0 h to 1000 h under ozone concentration 1000 pphm, the tensile strength of fiber decreased from 2332 MPa to 1954 MPa. The hydrogen bonds and partial amide groups in the fiber structure were damaged, and the surface chemical functional groups of the Kevlar fiber were reassembled under ozone exposure. Low molecular weight oxidation products, including -COO- structures, formed on the surface of the Kevlar fiber. This work explores the ground simulation method in a near-space environment and enriches the service data of airship envelope materials. [ABSTRACT FROM AUTHOR]

Acid coagulation is the most traditional latex coagulation technology, but this coagulation process leads to delayed vulcanization, corrosiveness, and environmental pollution. Different coagulation processes significantly impact the raw rubber network structure, leading to differences in the properties of both raw rubber and rubber vulcanizates. Raw rubber was prepared by three acid‐free coagulation processes: freeze, microwave, and flash drying. The network density, molecular chain flexibility, molecular weight, processing fluidity, and plasticity retention of the raw rubber were characterized, and the vulcanization characteristics, viscoelasticity, mechanical properties, and dynamic mechanical properties of the cured rubber composites were investigated. Raw rubbers prepared by microwave drying and flash drying had higher crosslink density, more flexible molecular chains, larger molecular weight, and wider molecular weight distribution, thereby increasing the crosslink density of rubber vulcanizates. The crosslink density of the raw rubber prepared by microwave drying versus the acid coagulated raw rubber increased by 51% to 105.71 mol/m3, the tensile strength increased by 16% to reach 28.12 MPa, and the elastic modulus and rolling resistance under dynamic stress increased. This paper provides a new idea for analyzing the relationship between the raw rubber network structure and the properties of vulcanized rubber. Highlights: Acid‐free raw rubbers are prepared by freeze, microwave, and flash drying.Coagulation processes significantly impact the raw rubber network structures.Effects of raw rubber network structures on properties are investigated.Crosslink density, plasticity retention, and tensile strength are improved. [ABSTRACT FROM AUTHOR]

To tackle the critical challenge concerning the disparate performance outcomes between the spoke and rim in extruded AZ80 magnesium alloy wheel hub, finite element simulation was used to optimize the shape parameters of the hollow billet and improved equivalent strain was achieved. The paper studied the microstructure evolution and mechanical property response of the alloy after the forming process. The experimental results showed that the grain sizes of the spoke and rim were 32.95 and 33.84 μm, respectively, when using the optimized shape parameters, and both of them were completely dynamically recrystallized. Although the fine grain strengthening and precipitation hardening effects were consistently obtained in both samples, a discernible distinction was revealed by the mechanical property analysis. Specifically, the yield strength (YS) and ultimate tensile strength (UTS) of the rim specimens evinced a notable 13.8 and 15.4% higher in comparison to the spoke specimens. This discrepancy was further elucidated by the texture analysis, which illuminated that the spoke was distinguished by an extrusion direction–transverse direction double-peak basal texture, while the rim was marked by a normal direction–transverse direction (ND–TD) double-peak basal component after extrusion. The distinct texture patterns gave rise to varying predominant deformation mechanisms during loaded at room temperature, where the textured TD-oriented grains within the spoke unfriendly promoted the initiation of {10-12} tensile twinning at low yield stress, while both the ND and TD component within the hub manifested a markedly high activation of prismatic slip with high yield stress. The cumulative effect of these contrasting deformation pathways ultimately led to a marked contrast in the YS between the two regions. [ABSTRACT FROM AUTHOR]

This research paper presents the fabrication of epoxy coatings along with the hybrid combination of SiO2 and ZrO2. The epoxy resin is incorporated with SiO2 as the primary pigment and ZrO2 as the synergist pigment. The study delves into the adhesion, barrier, and anti-corrosion properties of these coatings, enriched with silica and zirconium nanoparticles, and investigates their impact on the final properties of the epoxy coating. The epoxy resin, a Diglycidyl ether bisphenol-A (DGEBA) type, is cured with a polyamidoamine adduct-based curing agent. To evaluate the protective performance of silica SiO2 and zirconia ZrO2 nanoparticles in epoxy coatings, the coated samples were tested in a 3.5% NaCl solution. The experimental results clearly demonstrate a remarkable improvement in the ultimate tensile strength (UTS), yield strength (YS), and Elastic Modulus. In comparison to using SiO2 separately, the incorporation of both ZrO2 and SiO2 resulted in a substantial increase of 43.5% in UTS, 74.2% in YS, and 8.2% in Elastic Modulus. The corrosion test results revealed that the combination of DGEBA, SiO2, and ZrO2 significantly enhanced the anti-corrosion efficiency of the organic coatings. Both these pigments exhibited superior anti-corrosion effects and mechanical properties compared to conventional epoxy coatings, leading to a substantial increase in the anti-corrosion efficiency of the developed coating. This research focuses the potential of SiO2 and ZrO2 in hybrid combination for applications, where mechanical, corrosion and higher adhesion to the substrates are of prime importance. [ABSTRACT FROM AUTHOR]

Zinc (Zn)-based biodegradable materials show moderate degradation rates in comparison with other biodegradable materials (Fe and Mg). Biocompatibility and non-toxicity also make them a viable option for implant applications. Furthermore, Pure Zn has poor mechanical behavior, with a tensile strength of around 100–150 MPa and an elongation of 0.3–2%, which is far from reaching the strength required as an orthopedic implant material (tensile strength is more than 300 MPa, elongation more than 15%). Alloy and composite fabrication have proven to be excellent ways to improve the mechanical performance of Zn. Therefore, their alloys and composites have emerged as an innovative category of biodegradable materials. This paper summarizes the most important recent research results on the mechanical and biological characteristics of biodegradable Zn-based implants for orthopedic applications and the most commonly added components in Zn alloys and composites. [ABSTRACT FROM AUTHOR]

In this paper, the impact of the number of passes of equal channel angular pressing (ECAP) on mechanical properties and corrosion behavior of Al5085 alloys in an HNO3 solution is investigated. After a single pass of ECAP, the ultimate tensile strength (UTS) was increased noticeably from 275 MPa to 342 MPa. Also, the yield strength (YS) and microhardness were improved from 82 MPa to 118.5 MPa and 94 HV to 136 HV, respectively. After the second pass all UTS, YS, and microhardness increased by 13.5%, 17.8%, and 11.7% compared to the first pass. Meanwhile, the elongation to failure was reduced by 15% and 7.5% after one and two passes of the ECAP, respectively. According to scanning electron microscope (SEM) micrographs, unlike the unprocessed sample in which there is no evidence of pitting corrosion occurrence, after one pass ECAP, the pitting corrosion occurred through all the surfaces of the sample. Also, there is no evidence of pitting corrosion after two passes of ECAP. [ABSTRACT FROM AUTHOR]

Strengthening the CoCrFeNi high entropy alloy with a face-center cubic structure has become a research prospect in the last decade. Alloying with double elements, Nb and Mo, is an effective method. In this paper, to further enhance the strength of the Nb and Mo contained high entropy alloy, CoCrFeNiNb0.2Mo0.2 was annealing treated at different temperatures for 24 h. As a result, a new kind of Cr2Nb type nano-scale precipitate with a hexagonal close-packed structure was formed, which is semi-coherent with the matrix. Moreover, by adjusting the annealing temperature, the precipitate was tailored with a considerable quantity and fine size. The best overall mechanical properties were achieved in the alloy annealed at 700 °C. The yield strength, ultimate tensile strength, and elongation are 727 MPa, 1.05 GPa, and 8.38%, respectively. The fracture mode of the annealed alloy is a mixture of cleavage and necking-featured ductile fracture. The approach employed in this study offers a theoretical foundation for enhancing the mechanical properties of face-centered cubic high entropy alloys via annealing treatment. [ABSTRACT FROM AUTHOR]

The effects of Al addition on the microstructure and mechanical properties of Mg-Zn-Sn-Mn-Ca alloys are studied in this paper. It was found that the Mg-6Sn-4Zn-1Mn-0.2Ca-xAl (ZTM641-0.2Ca-xAl, x = 0, 0.5, 1, 2 wt.%; hereafter, all compositions are in weight percent unless stated otherwise) alloys have α-Mg, Mg2Sn, Mg7Zn3, MgZn, α-Mn, CaMgSn, AlMn, Mg32(Al,Zn)49 phases. The grain is also refined when the Al element is added, and the angular-block AlMn phases are formed in the alloys. For the ZTM641-0.2Ca-xAl alloy, the higher Al content is beneficial to elongation, and the double-aged ZTM641-0.2Ca-2Al alloy has the highest elongation, which is 13.2%. The higher Al content enhances the high-temperature strength for the as-extruded ZTM641-0.2Ca alloy; overall, the as-extruded ZTM641-0.2Ca-2Al alloy has the best performance; that is, the tensile strength and yield strength of the ZTM641-0.2Ca-2Al alloy are 159 MPa and 132 MPa at 150 °C, and 103 MPa and 90 MPa at 200 °C, respectively. [ABSTRACT FROM AUTHOR]