Search

In Germany, there are over 32,000 schools, representing great potential for climate protection. On the one hand, this applies to educational work, as understanding the effects of climate change and measures to reduce GHG emissions is an important step to empower students with knowledge and skills. On the other hand, school buildings are often in bad condition, energy is wasted, and the possibilities for using renewable energies are hardly used. In our "Schools4Future" project, we enabled students and teachers to draw up their own CO2 balances, identify weaknesses in the building, detect wasted electricity, and determine the potential for using renewable energies. Emissions from the school cafeteria, school trips, and paper consumption could also be identified. The fact that the data can be collected by the students themselves provides increased awareness of the contribution made to the climate balance by the various school areas. The most climate-friendly school emits 297 kg whilst the school with the highest emissions emits over one ton CO2 per student and year. Our approach is suitable to qualify students in the sense of citizen science, carry out a scientific investigation, experience self-efficacy through one's own actions, and engage politically regarding their concerns. [ABSTRACT FROM AUTHOR]

Reducing the heat demand of existing buildings is an essential prerequisite for achieving a greenhouse gas-neutral energy supply. Numerous studies and open-source tools deal with heat demand mapping. It is not uncommon that estimated heat demands deviate from real heat consumption, so existing approaches should be improved by including in-depth building information. Some tools have recognised this problem and offer built-in functions for factoring various parameters into their assessments. Nevertheless, the necessary information is usually missing and should be obtained first. In this paper, we analyse the impact of thermal refurbishment and climate on building heat demand; hence, generate public datasets with corresponding key figures for each building type in different efficiency states and years. Accounting for already performed refurbishments in methodologies for assessing the actual state heat demand for cities will result in a reduction of at least 8% up to more than 21%, depending on whether conventional or passive house components were installed. As a result of climatic differences within Germany, a building's heat demand can be up to 39% higher or up to 21% lower than the heat demand of an identical building in the reference climate of Germany. By further developing the approaches of the tools Hotmaps and Heat Cadastre Hamburg, we could improve the estimated heat demand of Hamburg to a value approximating the real consumption. [ABSTRACT FROM AUTHOR]

Against the background of climate protection and the rising costs of a fossil-fuel-based energy supply, the interest in the energy performance and indoor climate of buildings in real operation is rising. This paper, therefore, deals with the indoor climate investigation of two medium-sized office buildings in Germany by taking measurements over a whole year. These relate to one new building and one refurbished building. Sensors of various types were installed and operated in a large number of office rooms, so that in total results are available for over 100 rooms, typically occupied by one or two persons. The analysis focuses on the indoor temperature in summer and the air quality in winter based on the CO2 concentration. The comfort classes according to DIN EN 16798 including the adaptive comfort approach are used as a basis to cluster the results. Both buildings have movable sun protection and openable windows but no facilities for active cooling. They, thus, represent a large number of existing 'low tech' office buildings in Germany and central Europe. The results reflect the respective building concepts but also show a wide range between the rooms due to the user preferences and behaviour. The refurbished building shows better results, especially in terms of air quality but also in terms of summer room temperatures. This underlines the benefit of the targeted measures as a result of an analysis of the deficits in the existing building before the refurbishment. The additional measures for decentralised mechanical ventilation and passive cooling are having positive effects. As part of the projects, further measures to improve the indoor climate were investigated in both buildings. In one case, this involved CO2 traffic lights to stimulate personal window ventilation in winter, and in the other, the use of newly developed individual ceiling fans supports convective heat dissipation on the human body during hot spells in summer. The positive effect could be demonstrated for both measures. [ABSTRACT FROM AUTHOR]

Slowing down replacement cycles to reduce resource depletion and prevent waste generation is a promising path toward a circular economy (CE). However, an obligation to longevity only sometimes makes sense. It could sometimes even backfire if one focuses exclusively on material resource efficiency measures of the production phase and neglects implications on the use phase. The (environmental) lifespan of circular products should, therefore, be optimized, not maximized, considering all life cycle phases. In this paper, a generic method for determining the optimal environmental lifespan (OEL) of energy-using products (EuPs) in a CE is developed, allowing the simultaneous inclusion of various replacement options and lifetime extension processes, like re-manufacturing, in the assessment. A dynamic programming approach is used to minimize the cumulative environmental impact or costs over a specific time horizon, which allows considering an unordered sequence of replacement decisions with various sets of products. The method further accounts for technology improvement as well as efficiency degradation due to usage and a dynamic energy supply over the use phase. To illustrate the application, the OEL of gas heating appliances in Germany is calculated considering newly evolved products and re-manufactured products as replacement options. The case-study results show that with an average heat demand of a dwelling in Germany, the OEL is just 7 years for climate change impacts and 11 years for the aggregated environmental indicator, R e C i P e e n d p o i n t (t o t a l) . If efficiency degradation during use is considered, the OEL for both environmental impact assessment methods even lowers to 1 year. Products are frequently replaced with re-manufactured products to completely restore efficiency at low investment cost, resulting in higher savings potential. This not only implies that an early replacement before the product breaks down is recommended but also that it is essential to maintain the system and, thus, to prevent potential efficiency degradation. The results for cost optimization, as well as currently observed lifespans, vary considerably from this. [ABSTRACT FROM AUTHOR]

Community energy is seen as a helping hand for local, decentralized energy transition. Besides the main goal of supporting the community-friendly and socially acceptable development of renewable energies, the hope is also that a pro-environmental influence on sustainability behavior will be triggered when joining a community energy project. An analysis of a survey among 16 community energy projects in Germany, with 565 completed questionnaires, shows that a certain part of the members pays more attention to their energy behavior and develop a more positive attitude towards a decentralized energy transition and citizen participation after joining the community energy project. Therefore, we can empirically support that climate protection projects, such as community energy, influence pro-environmental attitudes and behavior, but this does not apply equally to all population groups. Members with higher income and stronger interest in returns are less likely to change their behavior. Based on these findings, we recommend the development of community energy policies that are more responsive to differences in social structure and address both privileged and underprivileged groups in a sophisticated way using specific offers and modes of involvement within the associations. [ABSTRACT FROM AUTHOR]

Schools play an important role in achieving climate protection goals, because they lay the foundation of knowledge for a responsible next generation. Therefore, schools as institutions have a special role model function. Enabling schools to become aware of their own carbon footprint (CF) is an important prerequisite for being able to tap the substantial CO2 reduction potential. Aiming at the direct involvement of students in the assessment process, a new assessment tool was developed within the Schools4Future project that gives students the opportunity to determine their own school's CF. With this instrument the CO2 emissions caused by mobility, heating and electricity consumption as well as for food in the school canteen and for consumables (paper) can be recorded. It also takes into account existing renewable energy sources. Through the development of the tool, not only a monitoring instrument was established but also a concrete starting point from which students could take actions to reduce Greenhouse Gas (GHG) emissions. This paper presents the tool and its methods used to calculate the CF and compares it with existing approaches. A comparative case study of four pilot schools in Germany demonstrates the practicability of the tool and reveals fundamental differences between the GHG emissions. [ABSTRACT FROM AUTHOR]

In this study, biological exhaust air treatment was combined with a recuperative heat exchanger in one process stage. The aim of this plant development and testing is not only to reduce ammonia from the exhaust air of pig houses but also to recover thermal energy at the same time. This is intended to offset the high operating costs of exhaust air treatment with savings of heating costs in cold seasons and to use the plant more efficiently. This system was tested for the first time under practical conditions in a pig fattening house in southern Germany. Three different assembly situations of the heat exchanger were examined for 13 days each and then compared with each other. The heating performance of the plant is primarily dependent on the outside air temperature and secondarily on the scrubbing water temperature. Depending on the assembly situation of the heat exchanger, an average heating performance of between 6.0 and 10.0 kW was observed; the amount of recovered thermal energy was between 1860 and 3132 kWh. The coefficient of performance (COP) ranked between 7.1 and 11.5. Furthermore, ammonia removal up to 64% was demonstrated. A long-term investigation of the system under practical conditions is recommended to validate the data collected in this study. [ABSTRACT FROM AUTHOR]