Search

Pterogyne nitens is commonly known in northeastern Brazil as a lesser-known fast-growing species in the Caatinga biome, which is a difficult place for tree development due to the low natural fertility soils and low availability of water. Due to the importance of expanding information about the anatomical wood properties of Caatinga native species, the aim of this work was to characterize the anatomical elements, to macroscopically describe the wood and make inferences about its possible end-uses. Maceration was performed which enabled measuring fiber dimensions, pore frequency and the following technological indexes: cell wall fraction, slenderness ratio, Runkel index and flexibility coefficient. Histological sections enabled describing the arrangements of the cellular elements in different observation sections and to determine the pore diameter. P. nitens wood has anatomical arrangements characterized by confluent axial parenchyma, being diffuse-porous with the presence of tylosis and heterogeneous/stratified rays (biseriate). The fibers were classified as very short (length 0.81 mm), not flexible and Runkel index 0.82. The pores were few in number with a frequency of 32.9 pores/mm2, distributed in a diffuse format and many were obstructed by tylosis. Based on the anatomical results and considering other technological studies, P. nitens wood is most suitable for charcoal production. [ABSTRACT FROM AUTHOR]

In this study, conventional restorative glass ionomer cement (GIC) was modified by embedding it with mechanically processed cellulose fibers. Two concentrations of fibers were weighed and agglutinated into the GIC during manipulation, yielding Experimental Groups 2 (G2; 3.62 wt% of fibers) and 3 (G3; 7.24 wt% of fibers), which were compared against a control group containing no fibers (G1). The compressive strengths and elastic modulus of the three groups, and their diametral tensile strengths and stiffness, were evaluated on a universal test machine. The compressive and diametral tensile strengths were significantly higher in G3 than in G1. Statistically significant differences in elastic modulus were also found between G2 and G1 and between G2 and G3, whereas the stiffness significantly differed between G1 and G2. The materials were then characterized by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Heterogeneously shaped particles were found on the G2 and G3 surfaces, and the cement matrices were randomly interspersed with long intermingled fibers. The EDS spectra of the composites revealed the elemental compositions of the precursor materials. The physically processed cellulosic fibers (especially at the higher concentration) increased the compressive and diametral tensile strengths of the GIC, and demonstrated acceptable elastic modulus and stiffness. [ABSTRACT FROM AUTHOR]

Lignin, the main source of renewable aromatics, has a complex structure, high polydispersity, and low reactivity, which hinders its large‐scale use. This study aims to improve lignin reactivity through heat treatment combined with fractionation by organic solvents or the pH effect. Heat treatment of commercial hardwood black liquor was performed at 225 °C for 150 min. The samples were then fractionated either by using organic solvents (ethyl acetate, ethanol, methanol, and acetone) or by lowering pH using hydrochloric acid (HCl) (pH values 1, 3, 5, 7, and 9). The fractionation was carried out in one step and in sequential mode. The fractionated samples were characterized chemically by the content of acid‐soluble and acid‐insoluble lignin, carbohydrates, ash, inorganic compounds (metals), elemental analysis, and by pyrolysis‐gas chromatography–mass spectrometry (Py‐GC–MS). The highest mass yields were obtained using the one‐step mode for both fractionations, with yields as high as 53.3% for organic solvents and 47.8% for the pH effect. Solvent fractionation reduced ash content by up to 75.4% and increased calorific value, carbon content, and total lignin content. Fractionation by pH effect showed an ash reduction of up to 55.9% and an increase in calorific value and carbon content of up to 8.7 MJ kg−1 and 49.7%, respectively. The Hansen solubility parameters were also calculated to address lignin's solubility in each of the tested solvents. These findings indicate that combining heat treatment and fractionation techniques improves lignin's chemical properties significantly, making it a more viable raw material for industrial use. This approach supports the circular economy by transforming lignin into a high‐value product, thereby promoting sustainable and efficient resource utilization across industries. [ABSTRACT FROM AUTHOR]

This study aimed to assess the effect of mechanical pretreatment on bleached eucalyptus kraft pulp fibers and investigate the influence of reaction time and temperature on the properties and yield of nanocrystalline cellulose (NCC) and microcrystalline cellulose (MCC). Two types of pulps were hydrolyzed, pulp 1 (control, whole fibers) and pulp 2 (mechanically pretreated, disintegrated fibers). NCC and MCC particles were obtained by sulfuric acid hydrolysis (60% w/w) of eucalyptus pulps under different conditions of time (30–120 min) and temperature (45–55 °C). Physical treatment of kraft pulp facilitated acid hydrolysis, resulting in higher NCC yields compared with no pretreatment. The morphologic properties and crystallinity index (CI) of NCC and MCC were little affected by pulp pretreatment. NCC particles obtained from pulps 1 and 2 were needle-shaped, with mean diameters of 6 and 4 nm, mean lengths of 154 and 130 nm, and CI of 74.6 and 76.8%, respectively. MCC particles obtained from pulps 1 and 2 were rod-shaped, with mean diameters of 2.4 and 1.4 µm, mean lengths of 37 and 22 µm, and CI of 73.1 and 74.5%, respectively. Pulps 1 and 2 and their respective NCC and MCC derivatives had a cellulose I crystalline structure. [ABSTRACT FROM AUTHOR]