Search

This work addresses the design of sub-terahertz narrow-band resonators for high performance and low-cost manufacturability. The intended application for these resonators is to realize narrow-band filters for passive millimeter-wave sounding of upper atmospheric humidity using the 380 GHz water vapor absorption line. Various narrow-band resonator designs and manufacturing processes were considered for this application. A design based on a waveguide split-ring resonator topology was selected to be developed and manufactured using laser machining. Experimental results are presented and compared with results from simulations for ten narrow-band resonators fabricated with a design center frequency in the WR-2.2 (325–500 GHz) waveguide band. [ABSTRACT FROM AUTHOR]

A new cost-effective radiometer has been designed, built, and tested to measure direct normal solar irradiance (DNI). The proposed instrument for solar irradiance measurement is based on an optical fiber as the light beam collector, a semiconductor photodiode to measure the optical power, and a calibration algorithm to convert the optical power into solar irradiance. The proposed radiometer offers the advantage of separating the measurement point, where the optical fiber collects the solar irradiation, from the place where the optical power is measured. A calibration factor is mandatory because the semiconductor photodiode is only spectrally responsive to a limited part of the spectral irradiance. Experimental tests have been conducted under different conditions to evaluate the performance of the proposed device. The measurements confirm that the proposed instrument performs similarly to the expensive high-accuracy pyrheliometer used as a reference. [ABSTRACT FROM AUTHOR]

The non-scanning radiometer with short-wavelength (SW: 0.2–5.0 μm) and total-wavelength (TW: 0.2–50.0 μm) channels is the primary payload of the Integrated Earth–Moon Radiation Observation System (IEMROS), which is designed to provide comprehensive Earth radiation measurements and lunar calibrations at the L1 Lagrange point of the Earth–Moon system from a global perspective. This manuscript introduces a radiometer preflight calibration methodology, which involves background removal and is validated using accurate and traceable reference sources. Simulated Earth view tests are performed to evaluate repeatability, linearity, and gain coefficients over the operating range. Both channels demonstrate repeatability uncertainties better than 0.34%, indicating consistent and reliable measuring performance. Comparative polynomial regression analysis confirms significant linear response characteristics with two-channel nonlinearity less than 0.20%. Gain coefficients are efficiently determined using a two-point calibration approach. Uncertainty analysis reveals an absolute radiometric calibration accuracy of 0.97% for the SW channel and 0.92% for the TW channel, underscoring the non-scanning radiometer's capability to provide dependable global Earth radiation budget data crucial to environmental and climate studies. [ABSTRACT FROM AUTHOR]

The IMERG data product is an optimal combination of precipitation estimates from the Global Precipitation Mission (GPM), making use of a variety of data types, primarily data from various spaceborne passive instruments. Previous versions of the IMERG product have been extensively validated by comparisons with gauge data and ground-based radars over land. However, IMERG rain rates, especially sub-daily, over open ocean are less validated due to the scarcity of comparison data, particularly with the relatively new Version 07. To address this issue, we consider IMERG V07 30-min data acquired in tropical cyclones over open ocean. We perform two tasks. The first is a straightforward comparison between IMERG precipitation rates and those retrieved from the GPM Dual-frequency Precipitation Radar (DPR). From this, we find that IMERG and DPR are close at low rain rates, while, at high rain rates, IMERG tends to be lower than DPR. The second task is the assessment of IMERG's ability to represent or detect structures commonly seen in tropical cyclones, including the annular structure and concentric eyewalls. For this, we operate on IMERG data with many machine learning algorithms and are able to achieve a 96% classification accuracy, indicating that IMERG does indeed contain TC structural information. [ABSTRACT FROM AUTHOR]

Climate change is undeniably one of the most pressing and critical challenges facing humanity in the 21st century. In this context, monitoring the Earth's Energy Imbalance (EEI) is fundamental in conjunction with greenhouse gases (GHGs) in order to comprehensively understand and address climate change. The French Uvsq-Sat NG pathfinder mission addresses this issue through the implementation of a Six-Unit CubeSat, which has dimensions of 111.3 × 36.6 × 38.8 cm in its unstowed configuration. Uvsq-Sat NG is a satellite mission spearheaded by the Laboratoire Atmosphères, Observations Spatiales (LATMOS), and supported by the International Satellite Program in Research and Education (INSPIRE). The launch of this mission is planned for 2025. One of the Uvsq-Sat NG objectives is to ensure the smooth continuity of the Earth Radiation Budget (ERB) initiated via the Uvsq-Sat and Inspire-Sat satellites. Uvsq-Sat NG seeks to achieve broadband ERB measurements using state-of-the-art yet straightforward technologies. Another goal of the Uvsq-Sat NG mission is to conduct precise and comprehensive monitoring of atmospheric gas concentrations (CO 2 and CH 4 ) on a global scale and to investigate its correlation with Earth's Outgoing Longwave Radiation (OLR). Uvsq-Sat NG carries several payloads, including Earth Radiative Sensors (ERSs) for monitoring incoming solar radiation and outgoing terrestrial radiation. A Near-Infrared (NIR) Spectrometer is onboard to assess GHGs' atmospheric concentrations through observations in the wavelength range of 1200 to 2000 nm. Uvsq-Sat NG also includes a high-definition camera (NanoCam) designed to capture images of the Earth in the visible range. The NanoCam will facilitate data post-processing acquired via the spectrometer by ensuring accurate geolocation of the observed scenes. It will also offer the capability of observing the Earth's limb, thus providing the opportunity to roughly estimate the vertical temperature profile of the atmosphere. We present here the scientific objectives of the Uvsq-Sat NG mission, along with a comprehensive overview of the CubeSat platform's concepts and payload properties as well as the mission's current status. Furthermore, we also describe a method for the retrieval of atmospheric gas columns (CO 2 , CH 4 , O 2 , H 2 O) from the Uvsq-Sat NG NIR Spectrometer data. The retrieval is based on spectra simulated for a range of environmental conditions (surface pressure, surface reflectance, vertical temperature profile, mixing ratios of primary gases, water vapor, other trace gases, cloud and aerosol optical depth distributions) as well as spectrometer characteristics (Signal-to-Noise Ratio (SNR) and spectral resolution from 1 to 6 nm). [ABSTRACT FROM AUTHOR]

A Moon-based radiometer can provide continuous measurements for the Earth's full-disk broadband irradiance, which is useful for studying the Earth's Radiation Budget (ERB) at the height of the Top of the Atmosphere (TOA). The ERB describes how the Earth obtains solar energy and emits energy to space through the outgoing broadband Short-Wave (SW) and emitted thermal Long-Wave (LW) radiation. In this work, a model for estimating the Earth's outgoing radiative flux from the measurements of a Moon-based radiometer is established. Using the model, the full-disk LW and SW outgoing radiative flux are gained by converting the unfiltered entrance pupil irradiances (EPIs) with the help of the anisotropic characteristics of the radiances. Based on the radiative transfer equation, the unfiltered EPI time series is used to validate the established model. By comparing the simulations for a Moon-based radiometer with the satellite-based data from the National Institute of Standards and Technology Advanced Radiometer (NISTAR) and the Clouds and the Earth's Radiant Energy System (CERES) datasets, the simulations show that the daytime SW fluxes from the Moon-based measurements are expected to vary between 194 and 205 Wm−2; these simulations agree well with the CERES data. The simulations are about 5 to 20 Wm−2 smaller than the NISTAR data. For the simulated Moon-based LW fluxes, the range is 251~287 Wm−2. The Moon-based and NISTAR fluxes are consistently 5~15 Wm−2 greater than CERES LW fluxes, and both of them also show larger diurnal variations compared with the CERES fluxes. The correlation coefficients of SW fluxes for Moon-based data and NISTAR data are 0.97, 0.63, and 0.53 for the months of July, August, and September, respectively. Compared with the SW flux, the correlation of LW fluxes is more stable for the same period and the correlation coefficients are 0.87, 0.69, and 0.61 for July to September 2017. [ABSTRACT FROM AUTHOR]

This study presents an original approach on how to generate a radiator with an emissivity less than one by using a conventional blackbody and a screen with a defined area density of holes. This is needed for the calibration of infrared (IR) radiometry, which is a very useful form of temperature measurement in industrial, scientific, and medical applications. One of the major sources of errors in IR radiometry is the emissivity of the surface being measured. Emissivity is a physically well-defined parameter, but in real experiments, it may be influenced by many factors: surface texture, spectral properties, oxidation, and aging of surfaces. While commercial blackbodies are prevalent, the much-needed grey bodies with a known emissivity are unavailable. This work describes a methodology for how to calibrate radiometers in the lab or in the factory or FAB using the "screen approach" and a novel thermal sensor dubbed Digital TMOS. The fundamental physics required to appreciate the reported methodology is reviewed. The linearity in emissivity of the Digital TMOS is demonstrated. The study describes in detail how to obtain the perforated screen as well as how to do the calibration. [ABSTRACT FROM AUTHOR]

Accurate information on tropical cyclone position, intensity, and structure is critical for storm surge prediction. Atmospheric reanalysis datasets can provide gridded, full coverage, long-term and multi-parameter atmospheric fields for the research on the impact of tropical cyclones on the upper ocean, which effectively makes up for the uneven temporal and spatial distribution of satellite remote sensing and in situ data. However, the reanalysis data cannot accurately describe characteristic parameters of tropical cyclones, especially in high wind conditions. In this paper, the performance of the tropical cyclone representation in ERA5 (European Centre for Medium-Range Weather Forecasts Reanalysis 5th Generation) is investigated and analyzed with respect to IBTrACS (International Best Track Archive for Climate Stewardship) during the period 2018–2020. Comparisons demonstrate that ERA5 winds significantly underestimate the maximum wind speed during the tropical cyclones (>30 m/s) compared to those provided by IBTrACS. An effective wind reconstruction method is examined to enhance tropical cyclone intensity representation in reanalysis data in 94 cases of 31 tropical cyclones 2018–2020. The reconstructed wind speeds are in good agreement with the SFMR (Stepped Frequency Microwave Radiometer) measured data and SMAP (Soil Moisture Active Passive) L-band radiometer remotely sensed measurements. The proposed wind reconstruction method can effectively improve the accuracy of the tropical cyclone representation in ERA5, and will benefit from the establishment of remote sensing satellite retrieval model and the forcing fields of the ocean model. [ABSTRACT FROM AUTHOR]

A method has been developed for the retrieval of the atmospheric boundary layer parameters in tropical cyclones, namely the dynamic speed, the wind speed at a 10 m height, and the roughness parameter. For the analysis, the wind speed profiles were obtained from NOAA GPS-dropsondes and collocated with the data from the Stepped-Frequency Microwave Radiometer (SFMR). The parameters of the atmospheric boundary layer from the GPS-dropsonde data were obtained by taking into account the self-similarity of the velocity defect profile. The emissivity, determined from the radiometric measurement data, was calibrated to the field data from the GPS-dropsondes. Empirical relations between the wind speed, dynamic wind speed, and aerodynamic drag coefficient with the surface emissivity have been proposed. Based on a comparison of the measured dynamic parameters and the surface emissivity, empirical formulas have also been proposed. From an analysis of cross-polarized Sentinel-1 SAR images and collocated SFMR measurements for hurricanes Irma (2017/09/07) and Maria (2017/09/21 and 2017/09/23), we have obtained the dependences of the NRCS on the ocean surface emissivity, surface wind speed, and friction velocity. These results could potentially be used to improve the algorithm for the retrieval of boundary layer parameters in tropical cyclones from remote sensing data. [ABSTRACT FROM AUTHOR]

It is important to monitor the take-off and landing of civil aircraft using passive detection methods. Due to the strict aircraft safety requirements and the electromagnetic environment around an airport, using too many active detection methods should be avoided. Using an aircraft's microwave radiation signal detection is very advantageous because it does not actively emit signals and has a strong cloud penetration, suitable for all-weather observation. This paper introduces a synthetic aperture microwave radiation system for monitoring the take-off and landing of civil aircraft, which is characterized by real-time two-dimensional imaging, and the image refresh rate can reach 10 ms, which meets the high refresh rate requirements for aircraft imaging. Applicable system parameters and antenna array distribution scheme and imaging algorithm are given. Then the paper focuses on the error analysis and correction method of the system. The correction method is simple and fast, which avoids the disadvantage that the error needs to be corrected regularly in the laboratory environment, and is suitable for airport application. Finally, the simulation and experimental results show that this technology can be used for real-time monitoring of civil aircraft during take-off and landing, and it is a practical means to assisting landing. [ABSTRACT FROM AUTHOR]

The Soil Moisture Active Passive (SMAP) mission includes a unique combination of instruments intended to provide daily global soil moisture data with high accuracy and resolution. Due to radar instrument failure, the default resolution of the data product decreased from the intended 9 km to 36 km shortly after the mission started to return data. To improve this, we employed the Scatterometer Image Reconstruction algorithm in its radiometer form (rSIR) to enhance the resolution of the radiometer brightness temperature measurements from which the soil moisture was derived. This paper compares the soil moisture estimates created from the rSIR-enhanced brightness temperatures with SMAP project radiometer L2_SM_SP and SMAP-Sentinel L2_SM_P products reported on 9 km and 3 km grids, respectively. We find that the difference of the rSIR-enhanced passive soil moisture product is generally within 0.020 cm 3 cm − 3 RMS of the 9 km SMAP radiometer L2_SM_SP and 0.045 cm 3 cm − 3 RMS of the 3 km SMAP-Sentinel L2_SM_P soil moisture products. The accuracy of the rSIR soil moisture can be improved by including better antenna pattern correction methods applied to the input TB measurements. [ABSTRACT FROM AUTHOR]

The Earth's radiation budget (ERB), measured at the top of the atmosphere (TOP), quantifies the radiation imbalance between the Earth–atmosphere system and space. The ERB's measurement accuracy depends on the observation system's design and calibration technology. Fitting regional scanning data from polar satellite payloads is the most common way to obtain the global radiation budget. Additionally, the radiometers are calibrated by onboard stable radiation sources. We propose a new ERB radiometer operating at the Lagrange L1 point of the Earth–Moon system, which has the characteristic of observing the Earth and Moon on a hemispheric spatial scale. Hence, earth-integrated radiation can be measured directly. Furthermore, the Moon is used as a natural source for on-orbit calibration, and the attenuation of the instrument is monitored and corrected through periodic observations. This paper presents the concept of the radiometer and focuses on the design and analysis of the radiometer's observation systems based on optical design and stray radiation suppression. The results show that the system has good imaging quality. The external stray radiation suppression reached an order of 10−8, and the thermal stray radiation can be eliminated by temperature control and compensation. The radiometer will provide long-term integrated ERB data. [ABSTRACT FROM AUTHOR]

Digital cross-correlation is central to many applications including but not limited to Digital Image Processing, Satellite Navigation and Remote Sensing. With recent advancements in digital technology, the computational demands of such applications have increased enormously. In this paper we are presenting a high throughput digital cross correlator, capable of processing 1-bit digitized stream, at the rate of up to 2 GHz, simultaneously on 64 channels i.e., approximately 4 Trillion correlation and accumulation operations per second. In order to achieve higher throughput, we have focused on frequency based partitioning of our design and tried to minimize and localize high frequency operations. This correlator is designed for a Passive Millimeter Wave Imager intended for the detection of contraband items concealed on human body. The goals are to increase the system bandwidth, achieve video rate imaging, improve sensitivity and reduce the size. Design methodology is detailed in subsequent sections, elaborating the techniques enabling high throughput. The design is verified for Xilinx Kintex UltraScale device in simulation and the implementation results are given in terms of device utilization and power consumption estimates. Our results show considerable improvements in throughput as compared to our baseline design, while the correlator successfully meets the functional requirements. [ABSTRACT FROM AUTHOR]

The paper investigates the theory of operation of a passive millimeter-wave seeker sensor using a fast electronic sequential-lobing technique and the experimental validation obtained through laboratory trials. The paper analyzes in detail the theoretical performance of a difference channel sensor and a pseudo-monopulse sensor deriving agile formulas for the estimation of target angular tracking accuracy and the subsequent experimental validation. [ABSTRACT FROM AUTHOR]

The increasing demand for light emitting diodes (LEDs) is driven by a number of application categories, including display backlighting, communications, signage, and general illumination. Nowadays, they have also become attractive candidates as new photometric standards. In recent years, LEDs have started to be applied as wavelength-selective photo-detectors as well. Nevertheless, manufacturers’ datasheets are limited about LEDs used as sources in terms of degradation with operating time (aging) or shifting of the emission spectrum as a function of the forward current. On the contrary, as far as detection is concerned, information about spectral responsivity of LEDs is missing. We investigated, mainly from a radiometric point of view, more than 50 commercial LEDs of a wide variety of wavelength bands, ranging from ultraviolet (UV) to near infrared (NIR). Originally, the final aim was to find which LEDs could better work together as detector-emitter pairs for the creation of self-calibrating ground-viewing LED radiometers; however, the findings that we are sharing here following, have a general validity that could be exploited in several sensing applications. [ABSTRACT FROM AUTHOR]

Total power radiometer has a simple configuration and the best theoretical resolution. Gain fluctuations and calibration errors, however, can induce severe errors in the solved scene brightness temperature. To estimate the overall radiometer performance we present a numerical simulation tool that can be used to determine the radiometric resolution. Our model considers three main components that degrade the radiometric resolution: thermal noise, 1/f noise and calibration errors. These error sources have long been known to exist, but comprehensive models able to account all these effects quantitatively and accurately in a practical manner have been missing. We have developed a radiometer simulation model that is able to produce radiometer signals that incorporate realistic radiometer effects that show up as noise and other errors in the radiometer video signal. Our simulation tool integrates the fundamental radiometer theories numerically and allows the investigation of different calibration schemes and receiver topologies. The model can be used as a guide for design and optimization as well as for verification of the radiometer performance. Moreover, it can be extended to a much larger and more complex radiometer systems allowing better system level performance estimation and optimization with minimal bread-board implementations. The model mimics real radiometer video data and thus the complete data analysis pipeline can be developed and verified before the real video data is available. In this paper, the model has been applied to a total power radiometer operating in the 52 GHz frequency range. [ABSTRACT FROM AUTHOR]

Ground-based estimates of aboveground wet (fresh) biomass (AWB) are an important input for crop growth models. In this study, we developed empirical equations of AWB for rice, maize, cotton, and alfalfa, by combining several in situ non-spectral and spectral predictors. The non-spectral predictors included: crop height (H), fraction of absorbed photosynthetically active radiation (FAPAR), leaf area index (LAI), and fraction of vegetation cover (FVC). The spectral predictors included 196 hyperspectral narrowbands (HNBs) from 350 to 2500 nm. The models for rice, maize, cotton, and alfalfa included H and HNBs in the near infrared (NIR); H, FAPAR, and HNBs in the NIR; H and HNBs in the visible and NIR; and FVC and HNBs in the visible; respectively. In each case, the non-spectral predictors were the most important, while the HNBs explained additional and statistically significant predictors, but with lower variance. The final models selected for validation yielded an R2 of 0.84, 0.59, 0.91, and 0.86 for rice, maize, cotton, and alfalfa, which when compared to models using HNBs alone from a previous study using the same spectral data, explained an additional 12%, 29%, 14%, and 6% in AWB variance. These integrated models will be used in an up-coming study to extrapolate AWB over 60 × 60 m transects to evaluate spaceborne multispectral broad bands and hyperspectral narrowbands. [ABSTRACT FROM AUTHOR]

The sea surface temperature (SST) is a crucial parameter system in climate monitoring. Satellite remote sensing is currently the most common approach for measuring long-term and large-area sea surface temperatures. The SST data measured by the satellite radiometer include the sea surface skin temperature (SSTskin) at a depth of approximately 10 μm. Satellite remote sensing measurement data must be compared and validated with on-site measured data. There are various solutions for on-site measuring instruments; the essential components are usually infrared radiation sensors with radiation output. This paper uses an ordinary integrated infrared thermometer without a radiation output function to remotely measure the sea surface temperature to achieve a high-precision measurement. The scheme of integrating infrared thermometers to measure the sea surface temperature is investigated in this paper. Based on Planck's formula, the bidirectional conversion relationship between temperature and radiation in a certain band is established. The experimental system introduced in this paper uses an integrated infrared thermometer to measure the small blackbody and the target in a cyclic measurement system. We combine it with the sea surface emissivity characteristics and eliminate the influence of sky background radiation on the sea surface to obtain the actual amount of radiation on the sea surface, from which we obtain the actual radiation amount on the sea surface. Accurate SST can be calculated from the actual amount of radiation at the sea surface. The temperature measurement accuracy can reach 0.1 K, allowing it to meet on-site temperature measurement requirements, as well as the comparison measurement requirements confirmed by satellite remote sensing on-site data. There are relatively few products available for sensors with a temperature measurement accuracy of 0.1 K on the market, and temperature measurement equipment with a temperature measurement accuracy of 0.1 K is relatively expensive. Cost is one of the important factors to consider when using in bulk, especially as global warming increases the need for ocean monitoring. The scheme proposed in this paper is beneficial to reduce the volume and weight of measuring instruments, reduce the cost, and promote the large-scale combined application of sea surface temperature change monitoring. [ABSTRACT FROM AUTHOR]

Methods for now-casting adverse weather conditions with the potential to cause disruption to aircraft landings often make use of real-time measurements at high temporal resolution. This paper describes processing methodologies developed to derive meteorological parameters from such measurements recorded in the vicinity of Hong Kong International Airport, specifically a radiometer in King's Park, a wind profiler and surface anemometer on Cheung Chau Island and weather buoys in the Pearl River estuary. These parameters are suitable for use as input to a now-casting application of the computationally efficient airflow model, FLOWSTAR, which has previously been shown to predict mountain waves generated by flow over Lantau Island to the southeast of the airport. Radiosonde data from King's Park have been used to test the radiometer processing method; the novel approach of using minimum and maximum potential temperature deviations from a series of height-dependent linear profiles to derive radiometer inversion layer parameters generates data that compares well with values derived from corresponding radiosonde profiles. Mountain wave strength depends on the magnitude of wind speed in the inversion layer; wind profiler data can be used to estimate typical and maximum wind speeds and associated wind directions using estimates of inversion layer depth derived from the radiometer data. With estimates of surface sensible heat flux appropriate for the airport's coastal location calculated using a marine boundary layer scheme, a dataset of meteorological parameters at 20-min resolution has been derived for input into the FLOWSTAR model. The combination of automated meteorological data processing methods and flow field modelling has the potential to form part of a now-casting system for determining strong wind shear conditions at the airport. [ABSTRACT FROM AUTHOR]

The Poland-AOD aerosol research network was established in 2011 to improve aerosol–climate interaction knowledge and provide a real-time and historical, comprehensive, and quantitative database for the aerosol optical properties distribution over Poland. The network consists of research institutions and private owners operating 10 measurement stations and an organization responsible for aerosol model transport simulations. Poland-AOD collaboration provides observations of spectral aerosol optical depth (AOD), Ångstrom Exponent (AE), incoming shortwave (SW) and longwave (LW) radiation fluxes, vertical profiles of aerosol optical properties and surface aerosol scattering and absorption coefficient, as well as microphysical particle properties. Based on the radiative transfer model (RTM), the aerosol radiative forcing (ARF) and the heating rate are simulated. In addition, results from GEM-AQ and WRF-Chem models (e.g., aerosol mass mixing ratio and optical properties for several particle chemical components), and HYSPLIT back-trajectories are used to interpret the results of observation and to describe the 3D aerosol optical properties distribution. Results of Poland-AOD research indicate progressive improvement of air quality and at mospheric turbidity during the last decade. The AOD was reduced by about 0.02/10 yr (at 550 nm), which corresponds to positive trends in ARF. The estimated clear-sky ARF trend is 0.34 W/m2/10 yr and 0.68 W/m2/10 yr, respectively, at TOA and at Earth's surface. Therefore, reduction in aerosol load observed in Poland can significantly contribute to climate warming. [ABSTRACT FROM AUTHOR]

To improve precipitation estimation accuracy, new methods, which are able to merge different precipitation measurement modalities, are necessary. In this study, we propose a deep learning method to merge rain gauge measurements with a ground-based radar composite and thermal infrared satellite imagery. The proposed convolutional neural network, composed of an encoder–decoder architecture, performs a multiscale analysis of the three input modalities to estimate simultaneously the rainfall probability and the precipitation rate value with a spatial resolution of 2 km. The training of our model and its performance evaluation are carried out on a dataset spanning 5 years from 2015 to 2019 and covering Belgium, the Netherlands, Germany and the North Sea. Our results for instantaneous precipitation detection, instantaneous precipitation rate estimation, and for daily rainfall accumulation estimation show that the best accuracy is obtained for the model combining all three modalities. The ablation study, done to compare every possible combination of the three modalities, shows that the combination of rain gauges measurements with radar data allows for a considerable increase in the accuracy of the precipitation estimation, and the addition of satellite imagery provides precipitation estimates where rain gauge and radar coverage are lacking. We also show that our multi-modal model significantly improves performance compared to the European radar composite product provided by OPERA and the quasi gauge-adjusted radar product RADOLAN provided by the DWD for precipitation rate estimation. [ABSTRACT FROM AUTHOR]

The Global Precipitation Measurement (GPM) Dual-Frequency Precipitation Radar (DPR) (Ku- and Ka-band, or 14 and 35 GHz) provides the capability to resolve the precipitation structure under moderate to heavy precipitation conditions. In this manuscript, the use of near-coincident observations between GPM and the CloudSat Profiling Radar (CPR) (W-band, or 94 GHz) are demonstrated to extend the capability of representing light rain and cold-season precipitation from DPR and the GPM passive microwave constellation sensors. These unique triple-frequency data have opened up applications related to cold-season precipitation, ice microphysics, and light rainfall and surface emissivity effects. [ABSTRACT FROM AUTHOR]

This paper presents a built-in calibration procedure of a 10-to-20 GHz polarimeter aimed at measuring the I, Q, U Stokes parameters of cosmic microwave background (CMB) radiation. A full-band square waveguide double directional coupler, mounted in the antenna-feed system, is used to inject differently polarized reference waves. A brief description of the polarimetric microwave radiometer and the system calibration injector is also reported. A fully polarimetric calibration is also possible using the designed double directional coupler, although the presented calibration method in this paper is proposed to obtain three of the four Stokes parameters with the introduced microwave receiver, since V parameter is expected to be zero for the CMB radiation. Experimental results are presented for linearly polarized input waves in order to validate the built-in calibration system. [ABSTRACT FROM AUTHOR]

This paper reviews the different remote sensing techniques found in the literature to monitor plant water status, allowing farmers to control the irrigation management and to avoid unnecessary periods of water shortage and a needless waste of valuable water. The scope of this paper covers a broad range of 77 references published between the years 1981 and 2021 and collected from different search web sites, especially Scopus. Among them, 74 references are research papers and the remaining three are review papers. The different collected approaches have been categorized according to the part of the plant subjected to measurement, that is, soil (12.2%), canopy (33.8%), leaves (35.1%) or trunk (18.9%). In addition to a brief summary of each study, the main monitoring technologies have been analyzed in this review. Concerning the presentation of the data, different results have been obtained. According to the year of publication, the number of published papers has increased exponentially over time, mainly due to the technological development over the last decades. The most common sensor is the radiometer, which is employed in 15 papers (20.3%), followed by continuous-wave (CW) spectroscopy (12.2%), camera (10.8%) and THz time-domain spectroscopy (TDS) (10.8%). Excluding two studies, the minimum coefficient of determination (R2) obtained in the references of this review is 0.64. This indicates the high degree of correlation between the estimated and measured data for the different technologies and monitoring methods. The five most frequent water indicators of this study are: normalized difference vegetation index (NDVI) (12.2%), backscattering coefficients (10.8%), spectral reflectance (8.1%), reflection coefficient (8.1%) and dielectric constant (8.1%). [ABSTRACT FROM AUTHOR]

This paper shows a simultaneous tri-band (S: 2.2–2.7 GHz, X: 7.5–9 GHz and Ka: 28–33 GHz) low-noise cryogenic receiver for geodetic Very Long Baseline Interferometry (geo-VLBI) which has been developed at Yebes Observatory laboratories in Spain. A special feature is that the whole receiver front-end is fully coolable down to cryogenic temperatures to minimize receiver noise. It was installed in the first radio telescope of the Red Atlántica de Estaciones Geodinámicas y Espaciales (RAEGE) project, which is located in Yebes Observatory, in the frame of the VLBI Global Observing System (VGOS). After this, the receiver was borrowed by the Norwegian Mapping Autorithy (NMA) for the commissioning of two VGOS radiotelescopes in Svalbard (Norway). A second identical receiver was built for the Ishioka VGOS station of the Geospatial Information Authority (GSI) of Japan, and a third one for the second RAEGE VGOS station, located in Santa María (Açores Archipelago, Portugal). The average receiver noise temperatures are 21, 23, and 25 Kelvin and the measured antenna efficiencies are 70%, 75%, and 60% in S-band, X-band, and Ka-band, respectively. [ABSTRACT FROM AUTHOR]

Providing uncertainties in satellite datasets used for Earth observation can be a daunting prospect because of the many processing stages and input data required to convert raw detector counts to calibrated radiances. The Sea and Land Surface Temperature Radiometer (SLSTR) was designed to provide measurements of the Earth's surface for operational and climate applications. In this paper the authors describe the traceability chain and derivation of uncertainty estimates for the thermal infrared channel radiometry. Starting from the instrument model, the contributing input quantities are identified to build up an uncertainty effects tree. The characterisation of each input effect is described, and uncertainty estimates provided which are used to derive the combined uncertainties as a function of scene temperature. The SLSTR Level-1 data products provide uncertainty estimates for fully random effects (noise) and systematic effects that can be mapped for each image pixel, examples of which are shown. [ABSTRACT FROM AUTHOR]

Offshore of many coastal regions, the ocean surface wind varies in speed and direction throughout the day, owing to forcing from land/sea temperature differences and orographic effects. Far offshore, both diurnal and semidiurnal wind vector variability has been noted in the Tropical Atmosphere Ocean-TRIangle Trans-Ocean buoy Network (TAO-TRITON) mooring data in the tropical Pacific Ocean. In this manuscript, the tropical diurnal wind variability is examined with microwave radiometer-derived winds from the Tropical Rainfall Measuring Mission (TRMM) and the Global Precipitation Measurement (GPM), merged with RapidScat and other scatterometer data. Since the relationship between wind speed and its zonal and meridional components is nonlinear, this manuscript describes an observationally based methodology to merge the radiometer and scatterometer-based wind estimates as a function of observation time, to generate a multi-year dataset of diurnal wind variability. Compared to TAO-TRITON mooring array data, the merged satellite-derived wind components fairly well replicate the semidiurnal zonal wind variability over the tropical Pacific but generally show more variability in the meridional wind components. The meridional component agrees with the associated mooring location data in some locations better than others, or it shows no clear dominant diurnal or semidiurnal mode. Similar discrepancies are noted between two forecast model reanalysis products. It is hypothesized that the discrepancies amongst the meridional winds are due to interactions between surface convergence and convective precipitation over tropical ocean basins. [ABSTRACT FROM AUTHOR]

A low-mass and low-volume dual-polarization L-band radiometer is introduced that has applications for ground-based remote sensing or unmanned aerial vehicle (UAV)-based mapping. With prominent use aboard the ESA Soil Moisture and Ocean Salinity (SMOS) and NASA Soil Moisture Active Passive (SMAP) satellites, L-band radiometry can be used to retrieve environmental parameters, including soil moisture, sea surface salinity, snow liquid water content, snow density, vegetation optical depth, etc. The design and testing of the air-gapped patch array antenna is introduced and is shown to provide a 3-dB full power beamwidth of 37°. We present the radio-frequency (RF) front end design, which uses direct detection architecture and a square-law power detector. Calibration is performed using two internal references, including a matched resistive source (RS) at ambient temperature and an active cold source (ACS). The radio-frequency (RF) front end does not require temperature stabilization, due to characterization of the ACS noise temperature by sky measurements. The ACS characterization procedure is presented. The noise equivalent delta (Δ) temperature (NEΔT) of the radiometer is ~0.14 K at 1 s integration time. The total antenna temperature uncertainty ranges from 0.6 to 1.5 K. [ABSTRACT FROM AUTHOR]

Continuous estimates of the vertical integrated precipitable water vapor content from the tropospheric delay of the signal received by the antennas of the global positioning system (GPS) are used in this paper, in conjunction with the measurements of the Meteosat Second Generation (MSG) spinning enhanced visible and infrared imager (SEVIRI) radiometer and with the lightning activity, collected here by the ground-based lightning detection network (LINET), in order to identify links and recurrent patterns useful for improving nowcasting applications. The analysis of a couple of events is shown here as an example of more general behavior. Clear signs appear before the peak of lightning activity on a timescale from 2 to 3 h. In particular, the lightning activity is generally preceded by a period in which the difference between SEVIRI brightness temperature (TB) at channel 5 and channel 6 (i.e., ∆TB) presents quite constant values around 0 K. This trend is accompanied by an increase in precipitable water vapor (PWV) values, reaching a maximum in conjunction with the major flash activity. The results shown in this paper evidence good potentials of using radiometer and GPS measurements together for predicting the abrupt intensification of lightning activity in nowcasting systems. [ABSTRACT FROM AUTHOR]

Climate on Earth is determined by the Earth Radiation Budget (ERB), which quantifies the incoming and outgoing radiative energy fluxes. The ERB can be monitored by non-scanning wide field-of-view radiometers, or by scanning narrow field-of-view radiometers. We propose an enhanced design for the wide field-of-view radiometer, with as key features the use of a near-spherical cavity to obtain a uniform angular sensitivity and the integration of the shuttered electrical substitution principle, eliminating long term drifts of the radiometer and improving its time response. The target absolute accuracy is 1 W/m 2 and the target stability is 0.1 W/m 2 per decade for the measurement of the total outgoing Earth's radiation. In order to increase the spatial resolution and to separate the total outgoing radiation into reflected Solar and emitted thermal radiation, we propose the joint use of the radiometer with wide field-of-view Shortwave (400–900 nm) and Longwave (8–14 μm) cameras. This paper presents the concept and design of the novel wide field-of-view radiometer, including simulations and analyses of its expected performance. We focus on mechanical design and the measurement characteristics based on optical and thermal analyses. In combination with the cameras, we obtain an estimated accuracy of 0.44 W/m 2 . [ABSTRACT FROM AUTHOR]

Land Surface Temperature (ST) represents the radiative temperature of the Earth's surface and is used as input to hydrological, agricultural, and meteorological science applications. Due to the synoptic nature of satellite imaging systems, ST products derived from space-borne platforms are invaluable for estimating ST at the local, regional, and global scale. In the past two decades, an emphasis has been placed on the need to develop algorithms necessary to deliver accurate surface temperature products to support the needs of science users. However, corresponding efforts to validate these products are hindered by the availability of quality ground-based reference measurements. The NOAA Surface Radiation Budget (SURFRAD) network is commonly used to support ST validation efforts, but their instrumentation is broadband (4–50 μ m) and several of their sites lack spatial uniformity. To address the apparent deficiencies within existing validation networks, this work discusses a prototype radiometer that was developed to provide surface temperature estimates to support validation efforts for spaceborne thermal instruments. Specifically, a prototype radiometer was designed, built, and calibrated to acquire ground reference data to be used to validate ST product(s) derived from Landsat 8 image data. Lab-based efforts indicate that these prototype instruments are accurate to within 1.28 K and initial field measurements demonstrate agreement to Landsat-derived ST products to within 1.37 K. [ABSTRACT FROM AUTHOR]

Accurate prediction of sea surface emission is the key for sea surface salinity retrieval from satellite microwave radiometer. In order to retrieve salinity from satellite observation, several sea surface microwave emission models have been developed based on theoretical or empirical methods and validated by in-situ measurements in different regions. However, their performances are still unclear in the Chinese coastal waters. In this study, based on two cruises measurements in the East China Sea (ECS), including the brightness temperature measured by a shipborne microwave radiometer and other auxiliary data (sea surface salinity, sea surface temperature and wind speed), the performances of different sea surface emission models are tested. The results showed that the developed models provide fairly good accuracy in predicting brightness temperature; for example, the accuracy of small perturbance/small scale approximation model (SPM/SSA), two-scale model (TSM) and empirical model is in the range from 0.6 K to 3 K. Moreover, the TSM and empirical models are further improved by optimizing the model parameters in the ECS. Finally, the sea surface salinity were retrieved from shipborne measured data based on the improved models, and the results show that the root mean square (rms) differences between retrieved and in-situ sea surface salinity is about 0.4 psu, indicating the significant improvement by the regional model parameters. [ABSTRACT FROM AUTHOR]

This paper presents the broadband antenna for the microwave radiometric sensing of internal body temperature. For broadband operation, the bow-tie antenna was designed and backed with a cylindrical cavity, which decreased environmental electromagnetic interference and also improved the directivity of the antenna. The broadband impedance-transforming balun in microstrip form was also designed to feed the bow-tie antenna, and was located inside the cavity. An impedance-matching dielectric layer (IMDL) was introduced on top of the bow-tie antenna, for impedance match with the human body with high permittivity. The fabricated antenna was measured in free space with the IMDL removed, showing an input reflection coefficient lower than −10 dB from 2.64 to > 3.60 GHz with antenna gain over 6.0 dBi and radiation efficiency over 74.7% from 2.7 to 3.5 GHz. The IMDL was re-installed on the cavity-backed bow-tie antenna to measure the antenna performance for the human head with relative permittivity of about 40. The measured reflection coefficient was as low as −28.9 dB at 2.95 GHz and lower than −10 dB from 2.65 to > 3.5 GHz. It was also shown that the designed antenna recovered a good impedance match by adjusting the permittivity and thickness of the IMDL for the different parts of the human body with different permittivities. [ABSTRACT FROM AUTHOR]

Accurate representation of the ocean-atmosphere coupling in weather, wave and climate models requires reliable estimates of air-sea surface fluxes of momentum, heat and mass. Whitecap fraction (W) usually quantifies the enhancement of the surface fluxes due to wave breaking. Satellite-based passive remote sensing of W from ocean surface brightness temperatures ( T B s) observes open ocean surface fluxes at low spatial resolution. Radiometric surface observations at higher resolution are necessary to monitor the complex environment in the coastal zone and in polar regions. We assess the feasibility of using the millimeter-wave frequencies (89 to 150 GHz) to observe whitecaps. We evaluate the derivative of the T B with respect to W as a measure for the observation of W. We describe the models and data used to evaluate the T B sensitivity to W for different instrumental and environmental conditions. Atmospheric absorption limits the ability to observe the surface at millimeter-wave frequencies. We find that the T B sensitivity to W at 89 GHz may be sufficient to support limited W retrieval from observations at altitudes below 1 km and that the T B sensitivity at 113 and 150 GHz is not sufficient. Clear skies, and low to moderate atmospheric humidity favor whitecap observations. [ABSTRACT FROM AUTHOR]

The High-resolution Infrared Radiation Sounder (HIRS) has been flown on 17 polar-orbiting satellites between the late 1970s and the present day. HIRS applications require accurate characterisation of uncertainties and inter-channel error correlations, which has so far been lacking. Here, we calculate error correlation matrices by accumulating count deviations for sequential sets of calibration measurements, and then correlating deviations between channels (for a fixed view) or views (for a fixed channel). The inter-channel error covariance is usually assumed to be diagonal, but we show that large error correlations, both positive and negative, exist between channels and between views close in time. We show that correlated error exists for all HIRS and that the degree of correlation varies markedly on both short and long timescales. Error correlations in excess of 0.5 are not unusual. Correlations between calibration observations taken sequentially in time arise from periodic error affecting both calibration and Earth counts. A Fourier spectral analysis shows that, for some HIRS instruments, this instrumental effect dominates at some or all spatial frequencies. These findings are significant for application of HIRS data in various applications, and related information will be made available as part of an upcoming Fundamental Climate Data Record covering all HIRS channels and satellites. [ABSTRACT FROM AUTHOR]

Near-surface remote sensing is an effective tool for in situ monitoring of canopy phenology, but the uncertainties involved in sensor-types and their deployments are rarely explored. We comprehensively compared three types of sensor (i.e., digital camera, spectroradiometer, and routine radiometer) at different inclination- and azimuth-angles in monitoring canopy phenology of a temperate deciduous forest in Northeast China for three years. The results showed that the greater contribution of understory advanced the middle of spring (MOS) for large inclination-angle of camera and spectroradiometer. The length of growing season estimated by camera from the east direction extended 11 d than that from the north direction in 2015 due to the spatial heterogeneity, but there was no significant difference in 2016 and 2018.The difference infield of view of sensors caused the MOS and the middle of fall, estimated by camera, to lag a week behind those by spectroradiometer and routine radiometer. Overall, the effect of azimuth-angle was greater than that of inclination-angle or sensor-type. Our assessments of the sensor types and their deployments are critical for the long-term accurate monitoring of phenology at the site scale and the regional/global-integration of canopy phenology data. [ABSTRACT FROM AUTHOR]

Lunar Flashlight (LF) is an innovative National Aeronautics and Space Administration (NASA) CubeSat mission that is dedicated to quantifying and mapping the water ice harbored in the permanently shadowed craters of the lunar South Pole. The primary goal is to understand the lunar resource potential for future human exploration of the Moon. To this end, the LF spacecraft will carry an active multi-band reflectometer, based on an optical receiver aligned with four high-power diode lasers emitting in the 1 to 2-μm shortwave infrared band, to measure the reflectance of the lunar surface from orbit near water ice absorption peaks. We present the detailed optical, mechanical, and thermal design of the receiver, which is required to fabricate this instrument within very demanding CubeSat resource allocations. The receiver has been optimized for solar stray light rejection from outside its field of view, and utilizes a 70 × 70-mm, aluminum, off-axis paraboloidal mirror with a focal length of 70 mm, which collects the reflected light from the Moon surface onto a single-pixel InGaAs detector with a 2-mm diameter, hence providing a 20-mrad field of view. The characterization of the flight receiver is also presented, and the results are in agreement with the expected performance obtained from simulations. Planned to be launched by NASA on the first Space Launch System (SLS) test flight, this highly mass-constrained and volume-constrained instrument payload will demonstrate several firsts, including being one of the first instruments onboard a CubeSat performing science measurements beyond low Earth orbit, and the first planetary mission to use multi-band active reflectometry from orbit. [ABSTRACT FROM AUTHOR]

An optimal payload selection conducted in the frame of the H2020 ONION project (id 687490) is presented based on the ability to cover the observation needs of the Copernicus system in the time period 2020–2030. Payload selection is constrained by the variables that can be measured, the power consumption, and weight of the instrument, and the required accuracy and spatial resolution (horizontal or vertical). It involved 20 measurements with observation gaps according to the user requirements that were detected in the top 10 use cases in the scope of Copernicus space infrastructure, 9 potential applied technologies, and 39 available commercial platforms. Additional Earth Observation (EO) infrastructures are proposed to reduce measurements gaps, based on a weighting system that assigned high relevance for measurements associated to Marine for Weather Forecast over Polar Regions. This study concludes with a rank and mapping of the potential technologies and the suitable commercial platforms to cover most of the requirements of the top ten use cases, analyzing the Marine for Weather Forecast, Sea Ice Monitoring, Fishing Pressure, and Agriculture and Forestry: Hydric stress as the priority use cases. [ABSTRACT FROM AUTHOR]

A rainfall retrieval algorithm for tropical cyclones (TCs) using 18.7 and 36.5 GHz of vertically and horizontally polarized brightness temperatures (Tbs) from the Microwave Radiation Imager (MWRI) is presented. The beamfilling effect is corrected based on ratios of the retrieved liquid water absorption and theoretical Mie absorption coefficients at 18.7 and 36.5 GHz. To assess the performance of this algorithm, MWRI measurements are matched with the National Snow and Ice Data Center (NSIDC) precipitation for six TCs. The comparison between MWRI and NSIDC rain rates is relatively encouraging, with a mean bias of −0.14 mm/h and an overall root-mean-square error (RMSE) of 1.99 mm/h. A comparison of pixel-to-pixel retrievals shows that MWRI retrievals are constrained to reasonable levels for most rain categories, with a minimum error of −1.1% in the 10–15 mm/h category; however, with maximum errors around −22% at the lowest (0–0.5 mm/h) and highest rain rates (25–30 mm/h). Additionally, Advanced Microwave Scanning Radiometer for Earth Observing System (AMSR-E) Tbs are applied to retrieve rain rates to assess the sensitivity of this algorithm, with a mean bias and RMSE of 0.90 mm/h and 3.11 mm/h, respectively. For the case study of TC Maon (2011), MWRI retrievals underestimate rain rates over 6 mm/h and overestimate rain rates below 6 mm/h compared with Precipitation Radar (PR) observations on storm scales. The Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI) rainfall data provided by the Remote Sensing Systems (RSS) are applied to assess the representation of mesoscale structures in intense TCs, and they show good consistency with MWRI retrievals. [ABSTRACT FROM AUTHOR]

The Radar Vegetation Index (RVI) is a well-established microwave metric of vegetation cover. The index utilizes measured linear scattering intensities from co- and cross-polarization and is normalized to ideally range from 0 to 1, increasing with vegetation cover. At long wavelengths (L-band) microwave scattering does not only contain information coming from vegetation scattering, but also from soil scattering (moisture & roughness) and therefore the standard formulation of RVI needs to be revised. Using global level SMAP L-band radar data, we illustrate that RVI runs up to 1.2, due to the pre-factor in the standard formulation not being adjusted to the scattering mechanisms at these low frequencies. Improvements on the RVI are subsequently proposed to obtain a normalized value range, to remove soil scattering influences as well as to mask out regions with dominant soil scattering at L-band (sparse or no vegetation cover). Two purely vegetation-based RVIs (called RVII and RVIII), are obtained by subtracting a forward modeled, attenuated soil scattering contribution from the measured backscattering intensities. Active and passive microwave information is used jointly to obtain the scattering contribution of the soil, using a physics-based multi-sensor approach; simulations from a particle model for polarimetric vegetation backscattering are utilized to calculate vegetation-based RVI-values without any soil scattering contribution. Results show that, due to the pre-factor in the standard formulation of RVI the index runs up to 1.2, atypical for an index normally ranging between zero and one. Correlation analysis between the improved radar vegetation indices (standard RVI and the indices with potential improvements RVII and RVIII) are used to evaluate the degree of independence of the indices from surface roughness and soil moisture contributions. The improved indices RVII and RVIII show reduced dependence on soil roughness and soil moisture. All RVI-indices examined indicate a coupled correlation to vegetation water content (plant moisture) as well as leaf area index (plant structure) and no single dependency, as often assumed. These results might improve the use of polarimetric radar signatures for mapping global vegetation. [ABSTRACT FROM AUTHOR]

While it has been proved that multiple scattering in the microwave frequencies has to be accounted for in precipitation retrieval algorithms, the effects of the random arrangements of drops in space has seldom been investigated. The fact is, a single rain drop size distribution (RDSD) corresponds with many actual 3D distributions of those rain drops and each of those may a priori absorb and scatter radiation in a different way. Each spatial configuration is equivalent to any other in terms of the RDSD function, but not in terms of radiometric characteristics, both near and far from field, because of changes in the relative phases among the particles. Here, using the T-matrix formalism, we investigate the radiometric variability of two ensembles of 50 different 3D, stochastically-derived configurations from two consecutive measured RDSDs with 30 and 31 drops, respectively. The results show that the random distribution of drops in space has a measurable but apparently small effect in the scattering calculations with the exception of the asymmetry factor. [ABSTRACT FROM AUTHOR]

Digital cross-correlation is central to many applications including but not limited to Digital Image Processing, Satellite Navigation and Remote Sensing. With recent advancements in digital technology, the computational demands of such applications have increased enormously. In this paper we are presenting a high throughput digital cross correlator, capable of processing 1-bit digitized stream, at the rate of up to 2 GHz, simultaneously on 64 channels i.e., approximately 4 Trillion correlation and accumulation operations per second. In order to achieve higher throughput, we have focused on frequency based partitioning of our design and tried to minimize and localize high frequency operations. This correlator is designed for a Passive Millimeter Wave Imager intended for the detection of contraband items concealed on human body. The goals are to increase the system bandwidth, achieve video rate imaging, improve sensitivity and reduce the size. Design methodology is detailed in subsequent sections, elaborating the techniques enabling high throughput. The design is verified for Xilinx Kintex UltraScale device in simulation and the implementation results are given in terms of device utilization and power consumption estimates. Our results show considerable improvements in throughput as compared to our baseline design, while the correlator successfully meets the functional requirements.