Search

As China's demand for paper products increases, China's paper industry faces enormous pressure to reduce greenhouse gas emissions. By using material flow analysis in combination with input–output analysis, this study measured the waste paper recovery rate in a more accurate method and analyzed the impact of waste paper recycling on the carbon emissions from China's paper industry. China's waste paper recovery rate estimated in this study was close to 70% in 2017, much higher than that of 48% obtained with the traditional method. The regression results displayed a negative relationship between waste paper recovery rate and CO2 emissions per unit of paper consumption during 2000–2017 in China. The rolling regression results further indicated that the impact of waste paper recycling was becoming stronger on reducing CO2 emissions per unit of paper consumption in China. Since an inverted "U" shape relationship exists between waste paper recovery rate and its reduction effect on carbon emissions from the paper industry, the regression results suggested that China's waste paper recovery rate has not reached the optimal level with regard to carbon emissions from China's paper industry. Thus, although China's waste paper recovery rate has reached a relatively high level, currently waste paper recycling is still an effective method to reduce carbon emissions from China's paper industry. [ABSTRACT FROM AUTHOR]

Paper mill sludge (PMS) is featured with a high content of cellulose and hemicellulose, and using its characteristics to make paperboard can achieve a high-value utilization of PMS, which has attracted growing interest. In this study, currently prevalent landfill, incineration technologies (generating heat and electricity by incineration), and three paperboard technologies (medium density fiberboard, pulp board, and corrugated paper) were evaluated and compared via life cycle assessment (LCA) and life cycle costing (LCC) methods. LCA results show that the PMS-to-pulp board outperforms others with an energy conservation and emission reduction (ECER) value of − 2.86 × 10−8, while the landfill exhibits the highest overall environmental impact with an ECER value of 4.80 × 10−9. LCC results reveal that the PMS-to-pulp board delivers the highest economic profit with $257.357, while the landfill is the lowest with $ − 35.63. The PMS paperboard technologies are more economically friendly than the incineration technologies due to additional electricity/steam consumption during the PMS pre-drying process in incineration. In addition, different scenarios were set up to explore national GHG emission reduction potential by increasing paperboard technologies application rate and reducing the proportion of landfill and incineration. The scenario analysis suggests that replacing 90% of landfill and incineration ratio with PMS paperboard technologies could tremendously improve the overall emission reduction performance with − 9.08 × 1010 kg CO2 eq. This result indicates that the PMS treatment technology transformation has a significant favorable impact on the achievement of the "carbon neutrality" target. [ABSTRACT FROM AUTHOR]

Some ancient Chinese paper artifacts dyed with amur cork tree bark extracts are currently preserved to different extents in museums and libraries worldwide. As traditional natural plant dyes, the long-term performance of the amur cork tree bark extract-dyed handmade paper has been questioned under a preserved environment. The photodegradation process of the extract-dyed papers was examined under accelerating artificial UVA irradiation conditions according to China national standard-paper and board- accelerated aging (exposure to light). Changes during aging were analyzed by optical observation and scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transform infrared spectrometry (FTIR), pH, and tensile strength and folding endurance tests. The results showed that the main components from extracted dyes played an important role in affecting the photodegradation properties of dyed paper. The changes in surface color, pH, morphology and mechanical properties after the artificial UVA accelerated degradation tests revealed that a suitable concentration of the extract dyes for maintaining the long-term irradiation stability of the paper is important. [ABSTRACT FROM AUTHOR]

Congestion is a well-known economic phenomenon in which excessive inputs lead to a decrease in the maximum possible outputs. This study analyzes the relationship between congestion and overinvestment using a data envelopment analysis framework to reveal that some congestion can be eliminated by increasing inputs. The proposed approach classifies congestion into two categories, relative and absolute congestion, depending on the possibility of eliminating congestion by increasing inputs. Corresponding methods for identifying and measuring congestion are proposed and employed for empirical analyses examining China's papermaking and paper products industry. We find that most congestion in 2013–2016 is in the relative congestion and could be eliminated by increasing inputs. The primary causes of congestion are identified based on our analysis and corresponding policy suggestions are proposed for eliminating congestion. [ABSTRACT FROM AUTHOR]

"Paper mills" are unethical outsourcing agencies proficient in fabricating fraudulent manuscripts submitted to scholarly journals. In earlier years, the activity of such companies involved plagiarism, but their processes have gained complexity, involving the fabrication of images and fake results. The objective of this study is to examine the main features of retracted paper mills' articles registered in the Retraction Watch database, from inception to the present, analyzing the number of articles per year, their number of citations, and their authorship network. Eligibility criteria for inclusion: retracted articles in any language due to paper mill activity. Retraction letters, notes, and notices, for exclusion. We collected the associated citations and the journals' impact factors of the retracted papers from Web of Science (Clarivate) and performed a data network analysis using VOSviewer software. This scoping review complies with PRISMA 2020 statement and main extensions. After a thorough analysis of the data, we identified 325 retracted articles due to suspected operations published in 31 journals (with a mean impact factor of 3.1). These retractions have produced 3708 citations. Nearly all retracted papers have come from China. Journal's impact factor lower than 7, life sciences journals, cancer, and molecular biology topics were common among retracted studies. The rapid increase of retractions is highly challenging. Paper mills damage scientific research integrity, exacerbating fraud, plagiarism, fake images, and simulated results. Rheumatologists should be fully aware of this growing phenomenon. [ABSTRACT FROM AUTHOR]

A PVA matrix was used to suppress infiltration and coffee-ring effects during colorimetric analysis on a paper substrate and improve the trace-level detection of nickel ions (Ni2+) in environmental samples. To improve the color response, a cross-linked PVA matrix was used to anchor the indicator reagent of Ni2+ on the surface of the porous paper substrate as well as reduce evaporation flow by increasing hydrogen bonding in the sample droplet. These phenomena mitigated the loss of color signal by suppressing infiltration and coffee-ring effects. Under optimized conditions, including crosslinker concentration and addition order, type of commercial filter paper, and loading volume of the PVA/indicator mixture, the sensor obtained a limit of detection (LOD) as low as 0.92 ppm and a notable linear behavior of R2 > 0.97 at a linear range of 0.5–50 ppm, which is sufficient for the detection of legal maximum residue limit (MRL) of Ni2+ in wastewaters in China. The PVA-assisted sensor showed good selectivity to most metal ions and could work at different pH levels ranging from 3 to 9. The sensor also exhibited highly sensitive and stable performance in repetitive measurements and had a shelf-life of more than 3 months. These results suggest that our work provides a facile approach to improving the sensitivity and reliability of paper-based sensors for monitoring trace-level Ni2+ concentration in aqueous samples with good selectivity and prolonged shelf-life. [ABSTRACT FROM AUTHOR]

China's pulp and paper industry (CPPI) has been always the main carbon emission source in recent years. However, the analysis on influencing factors of carbon emissions from this industry is insufficient. To address the issue, the CO2 emissions from CPPI are estimated in the period of 2005–2019, the driving factors of CO2 emissions are investigated by the logarithmic mean Divisia index (LMDI) method, the decoupling state of economic growth and CO2 emissions is determined by Tapio decoupling model, and finally, future CO2 emissions are predicted under four scenarios by the STIRPAT model to explore the potential of carbon peaking. The results show that CPPI exhibits a rapid increase and a fluctuating downward trend in CO2 emissions during the period of 2005–2013 and 2014–2019, respectively. The main promoting and inhibiting factors to the increase of CO2 emission are per capita industrial output value and energy intensity, respectively. There are five decoupling states of CO2 emissions and economic growth during the study period, and the CO2 emissions exhibit a weak decoupling state with the industrial output value growth in most years of the study period. It is very difficult to realize the carbon peaking goal by 2030 under the baseline and fast development scenarios. Therefore, efficient low carbon and strong low-carbon development policies are necessary and urgent for the realization of carbon peaking goal and the sustainable development of CPPI. [ABSTRACT FROM AUTHOR]

Aim: Over the last few decades, gut microbiota research has been the focus of intense research and this field has become particularly important. This research aimed to provide a quantitative evaluation of the 100 most-cited articles on gut microbiota and IBS and highlight the most important advances in this field. Methods: The database Web of Science Core Collection was used to download the bibliometric information the top 100 most-cited papers. Microsoft Excel 2021, CiteSpace, VOSviewer, R software, and an online analytical platform (https://bibliometric.com/) were was applied to perform bibliometric analysis of these papers. Results: The total citation frequency in the top 100 article ranged from 274 to 2324, with an average citation of 556.57. A total of 24 countries/regions made contributions to the top 100 cited papers, and USA, Ireland, and China were the most top three productive countries. Cryan JF was the most frequently nominated author, and of the top 100 articles, 20 listed his name. Top-cited papers mainly came from the Gastroenterology (n = 13, citations = 6373) and Gut (n = 9, citations = 3903). There was a significant citation path, indicating publications in molecular/biology/immunology primarily cited journals in molecular/biology/genetics fields. Keywords analysis suggested that the main topics on gut microbiota and IBS were mechanisms of microbiome in brain-gut axis." Behavior" was the keyword with the strongest burst strength (2.36), followed by "anxiety like behavior" (2.24), "intestinal microbiota" (2.19), and "chain fatty acid" (1.99), and "maternal separation" (1.95). Conclusion: This study identified and provided the bibliometric information of the top 100 cited publications related to gut microbiota and IBS. The results provided a general overview of this topic and might help researchers to better understand the evolution, Influential findings and hotspots in researching gut microbiota and IBS, thus providing new perspectives and novel research ideas in this specific area. [ABSTRACT FROM AUTHOR]

The coating technique, supposedly invented by Chinese papermakers no later than the 3rd century AD, greatly improved paper sheets' qualities of color, texture, writability, and printability. Alongside the dispersal of papermaking and surface-treatment techniques beyond China, coated papers were manufactured and used in many other regions of the world. Understanding the manufacture of coated papers, therefore, is crucial for perceiving how surface treatments were developed to meet the need for paper with enhanced properties. However, the characterization of coating and coating pigments on ancient Chinese papers has long remained an unsolved issue, and previous studies on this topic have often produced inconclusive results. To explore a non-invasive methodology that can more reliably characterize coated papers and the coating pigment on them, this article presents the results of a pilot study that applied micro-computed tomography (micro-CT) and Raman spectroscopy to samples of three Qing Dynasty (1644–1911 AD) papers and two handmade papers manufactured in China in the 1990s. Micro-CT revealed the coating layer(s) on Lajian (waxed coated paper) and Lengjinjian (gold-dusted paper) of the Qing Dynasty and characterized the modern raw xuan and bamboo papers as uncoated. Raman spectroscopy, together with handheld X-ray fluorescence analysis, identified the mineral-based pigment in the coating layer, suggesting the use of lead white or kaolin as the coating pigment. Additionally, Raman analysis confirmed the use of other mineral pigments (red lead and cinnabar), beeswax, and organic dyes (gamboge, kermesic acid, and possibly purpurin) in the manufacture of Lajian and Lengjinjian papers. The combination of micro-CT and Raman spectroscopy, it is therefore suggested, is a practical, more reliable approach for non-invasive investigation of coating and coating pigments on ancient Chinese paper specimens. [ABSTRACT FROM AUTHOR]

Unlike in developed countries, most public toilets in China do not provide toilet paper onsite and users must bring their toilet paper. Moreover, an open waste bin is placed in each user's cubicle to collect used toilet paper and tissues. Such practices, which are common in East Asia and central America, have induced a dilemma of toilet paper disposal because some municipalities have removed waste bins from public toilets to prevent virus transmission by fecal matter. As a consequence, users were forced to flush down their used toilet paper and tissues. Yet, it is unknown whether standard toilet paper can be flushed easily without causing issues in sewer operations. Here, we surveyed the conditions of toilets in university campus and other public facilities in different regions across China. We also evaluated the disintegration characteristics of toilet paper products both by conducting online surveys and by physical disintegration experiments. We found that only 15% of toilets provided toilet paper, while open waste bins occurred at nearly all sites. Further, our survey indicated that 82% of toilet paper products sold in China did not give any indication on their flushability, whereas 77% of US products did. Disintegration results showed that none of the five popular, best-selling toilet paper products passed the flushability standard. We propose strategies to solve the current toilet paper dilemma in developing communities. [ABSTRACT FROM AUTHOR]

Natural yellow plant dyes and traditional medicines were used widely on historical papers in ancient China for religious reasons and conservation considerations. This study aims to evaluate some traditional yellow botanical sources of dyes that contain different chemical colorant compositions in order to understand their effects on the properties of traditional handmade paper. The physical and chemical changes in paper specimens treated with plant dyes were studied by examining properties such as the color, pH, thermogravimetric (TG) characteristics, tensile strength, folding endurance and microstructure by scanning electron microscopy (SEM). The results indicated that different colorants had different toning effects and that the main components, including carboxyl and ketone groups, could affect the paper stability at high temperatures. The results also revealed that the mechanical properties of paper specimens were improved after treatment with plant dyes. The significant improvements in the tensile strength and folding endurance and the slightly higher decomposition temperature of Amur cork tree-dyed paper could be ascribed to the strong interaction between the colorants' main components and the fibers. The scientific evaluation of the property changes is therefore valuable information for weighing the advantages and disadvantages of the various yellow toning materials for paper conservation treatment. [ABSTRACT FROM AUTHOR]

In China, Xuan paper has been the paper of choice as artwork support and for conservation, for several centuries. However, little is known about its material properties, especially given the many grades of sized and unsized Xuan paper. In addition, there is a lack of information on its degradation. In this research, a selection of contemporary unsized Xuan papers was investigated, representing diverse raw materials. Seven out of twelve contemporary unsized Xuan papers were determined to be approximately neutral and contain > 2% alkaline reserve, indicating good durability. Viscometry was used to determine the degree of polymerisation (DP) as none of the samples gave significant reactions to the phloroglucinol spot test. The average DP of ten contemporary unsized Xuan papers is ~ 1700, excluding two papers that have presumably been sun-bleached, and that exhibit significantly lower DP. Using X-ray fluorescence, it can be demonstrated that Ca and Si are the dominant elements and interestingly, Ca content is directly correlated with ash content and with alkaline reserve. Accelerated degradation was performed at two sets of environmental conditions, i.e. 90 °C, 30% RH and 60 °C, 70% RH, and the established degradation rates agreed with the Collections Demography model of paper degradation meaning that degradation of Xuan papers proceeds in the same way as other types of paper. This research gives fundamental insights into contemporary unsized Xuan papers, which exhibit good stability during accelerated degradation despite the low starting DP in the context of the samples used in this study. Our findings may inform methods of Xuan paper production, selection of Xuan paper for conservation purposes, as well as preventive conservation of Xuan paper-based artefacts. [ABSTRACT FROM AUTHOR]

Electronic waste is always a big problem when it comes to the disposal of electronic appliances, and they pose a significant threat ecologically. New technology replaces the existing one, and the older one is discarded. Biodegradable electronics, as an emerging research area, gives viable solutions to the problem of E-waste. It mainly deals with the development of transient electronic devices, i.e., getting decomposed gradually or dissolvable in an eco-friendly way when their purpose has been achieved. This paper presents a scientometric analysis of the research in biodegradable electronics by employing a Scopus database of more than 1109 research articles, conference papers, review papers, and books published on this topic. This study is done over two decades of data from 2003 to 2023 on biodegradable electronics. It describes the trends and future of the research area using keyword analysis, citation network, and bibliometric tools. The study of the number of papers shows a 68%, 75%, and 55% increase in research articles, conference papers, and review documents in 2022. The country-wise contribution to the research shows that China, the USA, India, and South Korea are the major contributing nations. China is the most productive nation, with 297 publications. This paper reveals that the research area has increased the interest of researchers, and countries are collaborating to achieve sustainable development goals. The bibliometric analysis identifies various challenges to biodegradable electronics, such as degradation diversity, integration, fabrication and scalability. Based on these, the future aspects of biodegradable electronics are identified in organic bioelectronics, soft electronics, novel fabrication mechanisms, and Innovative chemistry for green electronics. This study will aid academia, researchers and government agencies in exploring biodegradable electronics with multifaceted society-wide applications. [ABSTRACT FROM AUTHOR]

Passive daytime radiative cooling (PRDC) is a promising technology providing a cooling strategy that radiates heat directly into outer space without additional energy consumption, a crucial consideration in controlling construction energy consumption. However, the preparation of PRDC materials with controlled radiative properties is still challenging because the radiative interface must be maintained in a clean environment. Herein, a densely distributed porous hybrid aerogel with controlled radiative properties was fabricated using the wollastonite and cellulose as building blocks for building energy-saving applications. To do this, the cellulose pulp was obtained by using waste paper as raw material. Then, the hybrid aerogels, comprising paper cellulose and wollastonite particles, were fabricated by combining the acrylic acid polymers (PAA) bonding, freeze drying and vapor deposition modification. The radiative cooling hybrid aerogel exhibits high solar reflectivity (94.6%) and high atmospheric emissivity (95.1%), due to the laminated design of wollastonite randomly dispersed in the radiative hybrid aerogel. The excellent PRDC capability is also proven by outdoor tests where practical temperature difference is ~ 6.3 ℃ and the maximum cooling power of 147.4 Wm−2 under direct sun irradiance. Wettability test infers that the hybrid aerogel has a static water contact angle of 144.07° ± 2°, thereby indicating its hydrophobicity. In addition, based on the Energyplus simulation, the hybrid aerogel exhibits an average annual cooling energy saving of 8% in buildings across China. The excellent radiative cooling and self-cleaning properties of hybrid aerogel make it durable for long-term outdoor PRDC applications. [ABSTRACT FROM AUTHOR]

Compared with wood pulp, straw pulp and papermaking, because of lower cost and abundancy of raw material, has become an indispensable approach in paper industry of China. However, its further application is limited by huge water consumption and wastewater discharge. By employing substance flow analysis, this study built up an optimization model and a performance evaluation system of water saving for the water-use network of a straw pulp and paper enterprise, after identifying the problems in present water consumption. Accordingly, an optimization plan was proposed to combine man-made water circulation with natural water circulation system. Additionally, a contrast analysis between the present and optimized water use was conducted. At last, we applied the proposed optimization plan to one of the most important and largest enterprises of straw pulp and paper industry in China as an illustration. Theoretically, water consumption could be reduced by 75.4 % without wastewater discharge after optimization. [ABSTRACT FROM AUTHOR]

Existing literature ignores to consider multiple types of pollutants when analyzing energy efficiency and its convergence. Under this background, using SuperSBM-GML model, the improved entropy method, and convergence model, this paper calculates the green total-factor energy efficiency and its evolution trend of 35 China's industrial sub-sectors considering multiple pollutants, and analyzes its convergence. The results indicate that the average score of industrial green total-factor energy efficiency is low, and there are significant differences among sub-sectors: "Utilization of waste resources" is the highest, while "Manufacture of paper and paper products" is the lowest. The green total-factor energy efficiency shows an overall upward trend from 2006 to 2021, the main driving force comes from technological progress, but numerous sub-sectors have not sufficiently caught up with existing cutting-edge technologies. Specifically, the growth rate of green total-factor energy efficiency in high-energy-consumption sub-sectors is higher than low-to-medium-energy-consumption sub-sectors. There are both σ-convergence and β-convergence in low-to-medium-energy-consumption group, indicating that development of sub-sectors is stable and outstanding. Nevertheless, the high-energy-consumption group only exhibits conditional β-convergence, revealing an imbalance in energy efficiency development. Consequently, formulating the benchmark level of energy efficiency and developing energy efficiency "leader" system are suggested for low-to-medium and high-energy-consumption sub-sectors, respectively. [ABSTRACT FROM AUTHOR]

This document is a correction notice for an article titled "Eliminating congestion in China's papermaking and paper products industry: from both the perspective of increasing and decreasing inputs" published in the Journal of Productivity Analysis. The authors acknowledge that there is overlap and duplication between their paper and a previously published paper, and they apologize for not acknowledging this in their article. The correction notice provides the correct citation for the original article and states that the authors regret the lack of transparency regarding the similarities between the two papers. [Extracted from the article]

Improving carbon emission efficiency is crucial for achieving carbon peak and carbon neutrality. This paper analyzes the carbon emission efficiency of Chinese cities using panel data from 275 prefecture-level cities between 2006 and 2020. The super-efficiency SBM (undesirable slacks-based measurement) model of undesired output, combined with kernel density estimation and exploratory data analysis, is employed. This study finds, firstly, from 2006 to 2020, the average efficiency of carbon emissions in Chinese cities declined from 0.53 to 0.48, indicating a downward trend. Secondly, from a temporal perspective, the level of dispersion in urban carbon emission efficiency has become increasingly distinct over time, coupled with a decrease in polarization. Thirdly, in terms of spatial analysis, urban carbon emission efficiency in China shows a positive correlation in a global context. In terms of local spatial correlation, it primarily exhibits high-high and low-low clusters, with a few instances of low–high and high-low clusters. Finally, based on the research findings, this paper proposes suggestions to improve urban carbon emission efficiency. [ABSTRACT FROM AUTHOR]

The digital finance generated by technology empowerment profoundly affects the innovative behavior of micro-enterprises. To estimate how digital finance influences the quantity and quality of green technological innovation, this paper introduces digital finance into endogenous economic growth model and further conducts correlation analysis with the combination of fixed effects model (FE) and panel threshold model (PTM). Moreover, this paper investigates the action mechanism from the perspective of financial constraint and financial cost. The empirical results indicate that digital finance improves the quantity and quality of green technological innovation significantly. Compared with the coverage of digital finance and digital services, the impact of usage depth on green innovation accumulates dynamically superimposed in the long term. The digital finance contributes to correct the mismatch of financial resources and further induces inclusive green innovation in the dimension of ownership, growth cycle, and enterprise scale. Mechanism analysis shows that the relief of financial constraint, environmental information disclosure, and increase of R&D investment are the main paths for digital finance to drive green innovation. With the different thresholds, the dynamic evolution process of green innovation driven by digital finance is characterized by "first quantitative change and then qualitative change." This paper suggests that the integration of technological innovation and digital financial services needs to build an inclusive digital financial service system, cultivate diversified financial formats, and improve the market environment of digital financial services. [ABSTRACT FROM AUTHOR]

The maritime sector plays a key role in transportation in the world, and over 90% of world trade is carried by ocean shipping. However, ships are large contributors to global emissions. Hence, a vast majority of research publications have focused on different emission monitoring techniques, which are essential to establishing required policies and regulations that reduce maritime transport emissions. Various documents have been published on monitoring maritime transport emissions affecting air quality since 1977. This paper presents a bibliometric analysis to explore evolution trends, gaps, challenges, and productive countries, as well as the most cited publications with high scholarly impacts. The annual growth of 9.64% in publications demonstrates an increasing interest in reducing maritime vessel emissions. Journal articles constitute 69% of publications, followed by conference papers (25%). China and the USA play a leading role in this field of research. Regarding active resources, the "Atmospheric Environment" journal accounts for the highest relevant publications, H-index, and total citations. Eventually, the temporal evolution of keywords shows the increasing trend towards sustainable maritime transport. [ABSTRACT FROM AUTHOR]

Common Reed ( Phragmites australis) is a wetland plant which is distributed worldwide, has a high biomass production, and provides important ecosystem services. In many developing and emerging countries it is an easily available and cheap raw material for diverse utilization, which may contribute significantly to employment and income generation for the local population. This case study investigates the reed utilization for pulp and paper production at the eutrophic Wuliangsuhai Lake, Inner Mongolia, China. We analysed the fluxes of materials and money along the supply chain (reed harvesting, processing and supply to final users, i.e. paper mills) as well as the division of work and costs at each production layer (network), based on the Netchain theory. The results make evident the importance of the paper industry and reed harvesting for local livelihood. They further reveal that the reed economy at Wuliangsuhai Lake is threatened by rising environmental standards for paper mills, change of market conditions and dependency on only two customers. Increasing revenues by finding new consumers or/and products, come to long-term contracts and improving harvesting efficiency are presented as ways to convert these threats into new opportunities. [ABSTRACT FROM AUTHOR]

Carbon abatement efforts in China are penetrating to sub-national level. Zhejiang province, as the 4th wealthy region in China and important player in global market (e.g., textiles, cloth, petroleum, and chemical products), lacks in-depth study of its climate change mitigation efforts, especially after China's accession to the WTO in 2001. This paper analyzed carbon emissions and intensity in Zhejiang province using most comprehensive and time-series dataset available to date since 2002. Its carbon emissions were growing at a declining speed, and carbon intensity was almost halved. The leading emitters largely agglomerate around Hangzhou Bay, close to Zhoushan Port and Shanghai Port. The growth in absolute emissions primarily arose from higher investment (323.1 Mt) and exports (280.6 Mt), while the slower growth was mainly due to efficiency improvements (− 245.7 Mt) stemming from energy and carbon abatement policies and inflows of emission-intensive products from the rest of China. Similarly, declined carbon intensity was mainly attributed to efficiency improvement. Major contributors were sector S13-Non-metallic minerals, S12-Chemicals, S26-Transport, storage and post, S07-Textiles, and S10-Paper. Economic restructuring played different roles on emissions and intensity during various development stages. Policy implications of the findings are discussed for future developments. [ABSTRACT FROM AUTHOR]

Scholarly efforts to predict the future character of the U.S.-China relationship abound. Few however looks to leaders’ beliefs as valid explanatory variables. In this paper, we argue that state leaders’ belief systems are key to understanding both the states’ intentions and policy choices. We analyze China’s national defense white papers (1998-2015) published to date as the source material to gauge the core collective beliefs of three generations of Chinese leadership. The operational code framework is employed to conceptualize and measure these beliefs. Our results identified important crossgenerational changes in a few belief indicators. In the Xi Jinping era, for instance, the political world is seen as less friendly and cooperative strategies are viewed less favorably. In terms of tactics, the policy tools “threaten” and “promise” are viewed as significantly more useful by the current leadership than by past Chinese leaders. [ABSTRACT FROM AUTHOR]

As the carrier of enterprise water resources management disclosure, water information disclosure is a means of expression of enterprises' environmental responsibility. First, a corporate water information disclosure quality evaluation index system and evaluation method are established, and with the help of the projection tracing method of accelerated genetic algorithm, 27 paper companies in China are selected as a sample and the disclosure quality level is analyzed empirically. Then, the analysis is carried out in terms of three changes in vertical trends, horizontal trends and changes in laws, regulations and policies, and the results show that Chinese paper and paper product enterprises have low quality of water information disclosure, weak disclosure content and low voluntary disclosure. Finally, feasible suggestions are made based on the evaluation of disclosure issues. [ABSTRACT FROM AUTHOR]

Background: As the volume of scientific publications increases, the rate of retraction of published papers is also likely to increase. In the present study, we report the characteristics of retracted papers from clinical neurosurgery and allied clinical and basic science specialties. Methods: Retracted papers were identified using two separate search strategies on PubMed. Attributes of the retracted papers were collected from PubMed and the Retraction Watch database. The reasons for retraction were analyzed. The factors that correlated with time to retraction were identified. Detailed citation analysis for the retracted papers was performed. The retraction rates for neurosurgery journals were computed. Results: A total of 191 retractions were identified; 55% pertained to clinical neurosurgery. The most common reasons for retraction were plagiarism, duplication, and compromised peer review. The countries associated with the highest number of retractions were China, USA, and Japan. The full text of the retraction notice was not available for 11% of the papers. A median of 50% of all citations received by the papers occurred after retraction. The factors that correlated with a longer time to retraction included basic science category, the number of collaborating departments, and the H-index of the journal. The overall rate of retractions in neurosurgery journals was 0.037%. Conclusions: The retraction notice needs to be freely available on all search engines. Plagiarism checks and reference checks prior to publication of papers (to ensure no retracted papers have been cited) must be mandatory. Mandatory data deposition would help overcome issues with data and results. [ABSTRACT FROM AUTHOR]

Groundwater is crucial for multiple uses over the world, especially in arid and semiarid regions. However, human activities significantly decreased groundwater quality. In this study, the spatiotemporal variation of groundwater quality was evaluated in an arid area where long-term paper wastewater irrigation has been implemented. For this study, seven wells were regularly monitored for physicochemical parameters over a period of 1 year. Statistical and graphical approaches were applied to interpret the spatiotemporal variation of groundwater quality parameters in the wastewater irrigation zone. Correlation analysis was also carried out to reveal the sources of some major ions. The results indicate that the groundwater type in the study area is dominated by the Cl-Na, followed by the HCO-Na, the HCO-Ca·Mg, and the SO·Cl-Ca·Mg types. Groundwater in the area is significantly contaminated locally with fluoride, nitrite and ammonia, and the chemical oxygen demand levels were increased in some groundwater monitoring wells. Most contaminants showed an increasing trend from the Yellow River water irrigation zone toward the wastewater irrigation zone. Rock weathering, mineral dissolution, and cation exchange are important processes controlling groundwater quality, but human activities, such as wastewater irrigation, play an undeniable role in affecting groundwater quality in this area. The results of this study contribute to the understanding of the formation and circulation of groundwater under human activities and provide a scientific basis for regional water quality evaluation, water quality improvement, and protection. [ABSTRACT FROM AUTHOR]

Computer-based testing (CBT), which refers to delivering assessments with computers, has been widely used in large English proficiency tests worldwide. Despite an increasing CBT in China, limited research is available concerning whether CBT can be used for the Test for English Majors-Band 4 (TEM 4). The current study investigated whether testing mode impacted TEM 4 score and factors (i.e., computer familiarity level and attitude towards CBT) that might correlate with performance on CBT of TEM 4. Overall 92 Chinese undergraduate students were randomly assigned to one of the groups, i.e., CBT or paper-based testing (PBT), and took the test. A mixed method was employed, including (1) quantitative and qualitative analysis of test performance in two modes, as well as CBT group participants' computer familiarity and attitudes towards the mode; and (2) thematic analysis of semi-structured interviews. The results revealed that (1) test scores in CBT and PBT were comparable; (2) two items in the computer familiarity questionnaire, i.e., comfort level of reading articles on the computer and forgetting time when using computers, positively correlated with CBT scores; and (3) participants' attitude towards CBT did not impact test performance. [ABSTRACT FROM AUTHOR]

DNA test is broadly used in diagnosis of crop disease and identification of genetic modified organism (GMO) in agriculture. However, rapid, low-cost, user-friendly, and field-deployable DNA test method is still limit. Recently, the RNA programmable nuclease of CRISPR/Cas is engineered as a new nucleic acid detection platform, but their application in plant remains to explore. In this study, we evaluated the Cas12a-based DNA detection for crop disease diagnosis and GMO test. A total of 14 crRNAs were designed to target two Magnaporthe oryzae genes and a synthetic Cry1C gene which encodes Bacillus thuringiensis δ-endotoxin and has been used to develop transgenic rice cultivar (Bt-rice) in China. Using a fluorescent reporter, targeted genes were easily detected by LbCas12a after recombinase polymerase amplification (RPA) for all crRNAs, despite that the signal strength varied 2–3-folds between different crRNAs. We further combined the filter paper-based DNA extraction and lateral flow assay (LFA) with RPA-Cas12a for DNA detection. This optimized Cas12a diagnostics method is carried at body temperature and does not require extra instrument except filter paper and LFA strip. Our data show that rice blast pathogen and Bt-rice were efficiently identified from leaf disc samples using this optimized DNA test method with highly active crRNAs. Moreover, LbCas12a exhibited variable nuclease activities on different targets; therefore, highly active crRNA is critical for successful DNA test using Cas12a and LFA. Owing to its simplicity, efficiency, and low-cost, DNA test using CRISPR/Cas12a would be easily applied in field for crop disease diagnosis and GMO administration. [ABSTRACT FROM AUTHOR]

Shadow play is an ancient traditional folk art in China and a precious Chinese artistic treasure. However, with the continuous diversification of entertainment forms, traditional shadow play art is gradually fading out of sight and even facing the possibility of having no successor. A fast method of creating digital shadow puppets based on parameterized templates is proposed in this paper. Adopting this method can transform the materials of a shadow character designed by an artist into a digital shadow puppet that can be interactively controlled by hand gestures. This paper classifies digital shadow puppets based on an analysis and summary of traditional shadow play art and designs the corresponding parameterized template for each type. In addition, a control method for shadow puppets based on the Leap Motion device is designed and implemented in this paper in accordance with common human hand gestures and the requirements for controlling shadow puppets. Based on the above work, we design and implement a platform for digital shadow story creation and performance and test the proposed method on this platform. The experimental results show that the method proposed in this paper can quickly create digital shadow puppets that can be interactively controlled and allow shadow plays to be performed based on gesture control. The research ideas and achievements of this paper help promote the development of digital shadow play technology and have great significance to the inheritance and development of traditional shadow play art. [ABSTRACT FROM AUTHOR]

Municipal solid waste (MSW) severely threatens human health and the ecological environment owing to its toxicity, mutagenic activity and carcinogenicity. The continuous increase in MSW together with stringent regulations makes sanitary disposal imperative. Waste sorting and recycling has been recognized as an efficient and economical treatment strategy. By analysing research data from 31 provinces between 2000 and 2017, the overarching goal of this work was to determine the characterizations and the compositions of MSW in China and then provide advices for sorting, transporting, storing and disposing of MSW. The results showed that the amount of MSW that was generated ranged from 0.08 to 2.34 kg d−1 ca−1 and averaged 0.73 kg d−1 ca−1 in China. The average bulk density, moisture content and the wet basis of the low calorific value of the MSW were 325 kg m−3, 50.3% and 4649 kcal kg−1. The MSW in China could be classified into four main categories, food waste, recycling waste, landfill waste and hazardous substances, and could be further classified into ten sub-categories. Overall, food waste was the most common and could be best managed via compost production. Bulk density was highly positively correlated with the ratio of the dust and bricks in all MSW and highly negatively correlated with the ratio of the food waste, metal, glass, plastic and rubber. The wet basis of the low calorific value was highly positively correlated with the ratio of the plastic and rubber, and the water content was highly positively correlated with the ratio of the food waste. Temporally, most of the components, especially waste paper and plastics, increased, while wood, dust and bricks decreased. [ABSTRACT FROM AUTHOR]

China, being the world's largest exporter, has now certain environmental commitments such as to achieve carbon neutrality before 2060. These commitments of China has raised a reasonable concern regarding the expected reduction in the production and export of pollution intensive goods in the future. Besides China, the most efficient countries in the region to produce these goods are most of the member countries from ASEAN. The current study therefore aims to analyze if in the future, China reduces the production and export of these goods, whether the selected ASEAN countries can be the next choice for the export of pollution intensive goods. Based on the data availability for the period 1990–2019, this study considers five selected ASEAN countries (ASEAN-5). The results are based on the Auto Regressive Distributive Lag (ARDL) bound testing approach to cointegration and Error Correction Modeling (ECM). The aggregate analysis of five pollution intensive goods (pulp and paper (341), industrial chemicals (351), non-metallic minerals products (369), iron and steel (371) and non-ferrous metals (372)) suggests that Foreign direct investment (FDI) inflow can significantly increase the export of pollution intensive goods only in case of Indonesia, Malaysia and Thailand. However, there is no significant effect of FDI on the export of pollution intensive goods in case of Philippines and Singapore. The disaggregate analyses of the five pollution intensive goods suggest that in each of the ASEAN-5 countries, FDI inflow can significantly increase the export of pollution intensive goods in some of these industries rather than in all of them. In nutshell, it is concluded that ASEAN-5 countries can be a potential choice for the export of pollution intensive goods in some of the pollution intensive industries but not in all of them. [ABSTRACT FROM AUTHOR]

The continuous expansion of the construction scale of smart city has reconstructed the urban information pattern. How to maintain the stability of information security while giving full play to the role of information sharing is a practical problem that must be solved for the sustainable development of smart city. Based on the information ecology theory, this paper construct the smart city information security risk evaluation system from six aspects. Then, zGT2FSs is established based on type-2 fuzzy set theory and IAA method, which fully considers the internal and external uncertainty of expert decision-making. According to the calculation results, the key influencing factors of information security risk of smart city are analyzed to provide suggestions and guidance for the formulation of information security control in the process of smart city construction in China. [ABSTRACT FROM AUTHOR]

Research on mountain ecosystem services (MES) under the influence of climate change and human activities has gradually become the focus of academic attention in recent years. Here, this study analyzes the research hotspots and frontiers of this field based on metrics including main research forces, core journals and papers, research hotspots and topics by using the methods of bibliometrics and text mining. The results revealed the following: (1) the number of papers is increasing rapidly in recent years. From 2015 to 2019, 929 papers were published, with an average of 185 papers per year. But the average cited times of those papers is declining, dropped from 6.01 in 2016 to 4.2 in 2019. The USA, UK, and China rank the top three of the number of papers. Univ Maryland, Univ Oxford and Univ Wisconsin have the greatest influence, with an average of more than 77 citations per paper; (2) The most cited journals are PNAS, WETLANDS, ECOLOGY, AND SOCIETY, which are cited 191.54, 53.91, and 40.00 respectively. Most papers were published in OA journals including SUSTAINABILITY, WATER, Forests since 2017. Ten core papers undertaking knowledge transfer in this field have been identified; (3) analysis of the keywords found a new trend of integration of natural science and humanities. In two development stages of 2000–2014 and 2015–2019, the research hotspots mainly focused on mountain water resources, forest resources, land resources and the impact of climate change and human activities, and there are obvious differences and characteristics in different stages. The hotspot worthy of attention in the near future is the assessment of mountain ecosystem services capacity and value. This is the first comprehensive visualization and analysis of the research hotspots and trends of mountain ecosystem services. [ABSTRACT FROM AUTHOR]

The article discusses the results of the study on the levels of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in some bleached pulps that were taken from five paper mills in China. Raw materials from the mills are pulped with the use of the kraft process, bleached and then converted into paper. It was found out that the content of 2378-tetrachlorodibenco-p-Dioxin in the pulps is higher than that of softwood pulps and bleached hardwood. The quantity of PCDFs is low compared to PCDDs. The study also revealed that dibenzo-p-dioxin,dibenzofuran and chlorinated phenols are not precursors of PCDD's and PCDF's in the bleaching of non-wood fiber pulps with hypochlorite.

The bioaccumulation of and resistance to different heavy metals in soil was tested using Mongoloniscus sinensis, a terrestrial isopod endemic to china, and results show that: (1) the median lethal concentration (LC50) of Pb, Zn, Cd in the filter paper contact test after 48 h was 197.6, 503.7, 448.0 µg cm− 2, LC50 of Pb-Zn compounds was 173.8 and 440.8 µg cm− 2 and after 14 days of soil contamination LC50 was 2917.0, 2977.9, 5048.4 mg kg− 1, LC50 of Pb-Zn compounds was 1219 and 1463 mg kg− 1. Thus Zn turned out to be less toxic than Cd in the filter paper contact test, while their sequence of toxicity was reversed during the soil exposure test, which shows that M. sinensis can tolerate a dose of Zn and Cd. (2) analysis of body burdens showed that the sequence of internalized metal concentrations was Pb < Cd < Zn, which indicates that heavy metals in soil can be enriched and absorbed by M. sinensis, and that it is much more efficient at absorbing Zn and Cd than Pb. [ABSTRACT FROM AUTHOR]

Compared with financial information, whether corporate social responsibility disclosure has impacts on debt financing cost has obviously become a heated topic in the academic. This paper selects A-share listed companies in Shanghai and Shenzhen stock markets of China from 2013 to 2017 as sample to study the impact of corporate social responsibility disclosure on debt financing cost, including bond financing cost and bank loan cost. In addition, this paper divides the sample into voluntary corporate social responsibility disclosure group and mandatory corporate social responsibility disclosure group and studies whether the effects of voluntary corporate social responsibility disclosure and mandatory corporate social responsibility disclosure on bond financing cost and bank loan cost are different. The empirical results are presented as follows: Firstly, enterprise disclosing high-quality corporate social responsibility report is more conducive to reducing the debt financing cost. Specifically, corporate social responsibility disclosure significantly lowers both the bond financing cost and bank loan cost. Moreover, the reduction impact of corporate social responsibility disclosure on bond financing cost is greater than that of bank loan cost. Secondly, enterprises voluntarily disclosing corporate social responsibility reports are more conducive to reducing the debt financing cost than that of enterprises mandatorily disclosing corporate social responsibility reports. Thirdly, non-state-owned enterprises are more conducive to reducing debt financing cost than that of state-owned enterprise. The enterprises with more market competition are more conducive to reducing the debt financing cost than the oligopolistic enterprises. Finally, this paper concludes and gives policy implications. This paper amplifies the literature regarding the economic consequences of corporate social responsibility disclosure and improves the understanding of the impact of corporate social responsibility disclosure on debt financing cost. [ABSTRACT FROM AUTHOR]

Energy shortage and excessive carbon emissions have become the main constraints to the sustainable development of China's logistics industry. Improving the efficiency of the logistics industry is crucial to promoting regional ecological environment protection and sustainable development of the logistics industry. In this paper, the efficiency of China's logistics industry in 2013–2019 is evaluated by using the non-oriented EBM model considering the unexpected output, and then the influencing factors of the efficiency of the logistics industry in the central region are analyzed by using the panel Tobit model. The results show that the logistics industry in the central region is at a low efficiency level. Factors, such as the level of economic development, industrial structure and technical level have a significant positive impact on the efficiency of the logistics industry in the central region, while factors such as government support and logistics infrastructure have a significant negative impact on the efficiency of the logistics industry in the central region. Finally, the paper puts forward some targeted recommendations for the sustainable development of the logistics industry in the central region. [ABSTRACT FROM AUTHOR]

In order to clarify the suction characteristics of unsaturated clay under different conditions of water and salt, taking soil in western Jilin province, China as the research object, the suctions (matrix suction and osmotic suction) of samples with different water content, salt type, and salt content were determined by filter paper method. The results indicate that salt type and content have insignificant influence on the matrix suction. With the increase of water content, the matrix suction decreases at different rates in different suction regimes. When water content is constant, the osmotic suction increases with the increase of salt content, and under the condition of a constant salt content, the osmotic suction first increases and then decreases with the increase of ion concentration of the pore water, and can reach tens of MPa. The concept of suction equilibrium water content is proposed. When water content of sample is higher than this value, the magnitude of osmotic suction will always be greater than that of matrix suction. This indicates the necessity to consider osmotic suction in the presence or change of salt in soil. The applicability of the traditional models of matrix suction and osmotic suction in the full suction range of clay is discussed, and it is found that the traditional models cannot make a full explanation to the variation in suction. Based on the experimental data, an improved van Genuchten matrix suction model and an osmotic suction model, transformed by the Planck blackbody radiation formula, are proposed. [ABSTRACT FROM AUTHOR]

The EU and China are both partners and competitors. They share certain common interests but have disagreements on some other issues. Both sides have published a number of policy papers in the past three decades: six by the EU and three by China. This paper will first examine the EU's policy papers one by one to find how the EU's China policy evolves and then look at China's EU policy papers to understand its objectives in relationship with the EU and compare the convergences and divergences between the EU and China revealed by these policy papers. In doing so, some keywords are selected from these documents. Some of them demonstrate how the relationship evolves and some others reveal the rising differences between the two. As the policy papers are important official documents to understand the objectives and actions of both the EU and China, a study of these policy papers would help highlight from where the relationship came and to where it is going. [ABSTRACT FROM AUTHOR]

This study explores the characteristics of the literature on microalgae-based wastewater treatment during the past 20 years, based on the Web of Science Core Collection database and its scientometric techniques. The results reveal that the literature on microalgae-based wastewater treatment has grown rapidly with 2621 publications and 54,388 citations in total. Most of the document types are journal articles, constituting 80.7% of the total records. China and the USA are the two most active countries, regarding the publications and cooperation in this filed from the viewpoint of the number of publishing papers, total number of citations, and the number of multinational author papers. The Chinese Academy of Sciences is the largest institutional contributor, publishing 2.3% of the papers, followed by the Indian Institute of Technology (2.2%) and Council of Scientific & Industrial Research (2.1%). The most publishing author is Ruan (35 papers) with the highest number of citation (2460 times). "Bioresource Technology" is the most publishing journal with 365 published papers, while 36.2% of the total sample is published in the subject area of "Environmental Sciences Ecology." The most cited paper in the past 20 years is a review of the status of phosphorus removal in wastewater by de-Bashan in 2004. Bibliometric analysis has systematically combed the development system of microalgae-based wastewater treatment in the past 20 years and has a great potential to gain valuable insights for the future development, which provides a supplement to the common content analysis. [ABSTRACT FROM AUTHOR]

The USA, China and India are the top three producers of municipal solid waste. The composition of solid wastes varies with income: low-to-middle-income population generates mainly organic wastes, whereas high-income population produces more waste paper, metals and glasses. Management of municipal solid waste includes recycling, incineration, waste-to-energy conversion, composting or landfilling. Landfilling for solid waste disposal is preferred in many municipalities globally. Landfill sites act as ecological reactors where wastes undergo physical, chemical and biological transformations. Hence, critical factors for sustainable landfilling are landfill liners, the thickness of the soil cover, leachate collection, landfill gas recovery and flaring facilities. Here, we review the impact of landfill conditions such as construction, geometry, weather, temperature, moisture, pH, biodegradable matter and hydrogeological parameters on the generation of landfill gases and leachate. Bioreactor landfills appear as the next-generation sanitary landfills, because they augment solid waste stabilization in a time-efficient manner, as a result of controlled recirculation of leachate and gases. We discuss volume reduction, resource recovery, valorization of dumped wastes, environmental protection and site reclamation toward urban development. We present the classifications and engineered iterations of landfills, operations, mechanisms and mining. [ABSTRACT FROM AUTHOR]

Green bonds, a new green financial instrument, encourage enterprises to achieve high-quality development through green technology innovation. However, a lack of research is currently being conducted into the effect of green bond issuance in China. Can green bonds effectively empower enterprises to green innovation? What is the underlying mechanism? In the context of carbon-neutral strategies, it is significant to answer these questions scientifically. This paper uses a quasi-natural experiment of the launch of the green bond market in China in 2016 to conduct empirical studies based on the panel data of 1 558 non-financial Chinese-listed enterprises from 2015 to 2020 with the multi-period difference-in-difference model. The results show that ① issuing green bonds can significantly empower enterprises' green technology innovation. The empowering effect is mainly for green utility patents rather than green invention patents. This result remains after dynamic heterogeneity analysis, placebo test, and other tests. In addition, the effect has a lag. ② Heterogeneity tests show that this empowerment effect varies across enterprises with different property rights, industries, and regions. ③ In terms of the mechanism of action, green bonds can enhance enterprises' ability to innovate green technology by increasing the proportion of long-term loans and improving their debt structure. This paper broadens the relevant literature on the economic consequences of green bonds and the influencing factors of enterprises' green technology innovation and provides policy suggestions for further improving the analysis of green bonds. [ABSTRACT FROM AUTHOR]

Based on the theory of developmental evaluation, this paper develops a new development-oriented research evaluation model called "four abilities", with "basic development ability", "process development ability", "achievement ability" and "influence ability" as key dimensions, which can be applied in different situations such as recruitment, performance appraisal, promotion evaluation, tenure review, and selection of honorary academic awards. Based on the data from the Youth Fund of the Ministry of Management Science of National Natural Science Foundation of China (NSFC) from 2014 to 2018, this paper takes the developmental evaluation of early career researchers as an example, treating the existing research output as the development goal and the "development ability" of early career researchers as the explanatory factor. Then the propensity score matching method (PSM) method is adopted to control the sample self-selection bias in the way of reverse order evaluation, so as to explain whether the guiding indicator "development ability" is conducive to the development of researchers. The results indicate that strong "process development ability" of newly recruited researchers in the first 3 years of employment period can significantly promote their future research performance, which has important implications for the current evaluative culture overemphasizing short-term output. Through the application of the "four abilities" model integrating various dimensions composed of potential, capacity, output and impact, researchers at different career stages are guided to concentrate more on long-term academic mission and to achieve better career development based on their differentiated development needs. [ABSTRACT FROM AUTHOR]

With the development of society, the number of female-headed households is on the rise. Based on the data from the China Household Finance Survey (CHFS) in 2019, this paper establishes a Tobit model to study the influence of female-headed households on household debt risk. Results indicate that female-headed households can substantially reduce household debt risk, and this conclusion still holds after overcoming endogeneity issues. Further tests on the mediating effect reveal that risk aversion and housing property holding have partial mediating effects and masking effects, respectively, in the path of female-headed households affecting household debt risk. In addition, the heterogeneity analysis indicates that the influence of female-headed households on household debt risk is more significant in third-tier cities, as well as in families without children, families without elderly members, and families with more than two elderly members. The conclusions of this paper provide a reference for the relevant policy measures to reduce household debt risk and promote gender equality. [ABSTRACT FROM AUTHOR]

This paper considers how 'knowledge' of China was presented for Victorian and Edwardian children in The Boy's Own Paper ( BOP) between 1879 and 1914. It considers how genre affects the representation of China in the BOP by comparing travel narratives and adventure stories. First, it focuses on non-fiction about China, examining the rhetorical strategies employed by the authors of travel narratives. The travellers express confidence in their ability to survey the land and present readers with the idea that China is abundant in resources awaiting British discovery. Second, the article discusses adventure stories about opium and piracy written during a period when the tension between the British and the Chinese was particularly fraught over these issues. While the authors of the adventure stories created a strong contrast between the Chinese as villains and the British as heroes, the BOP travel writers provide contradictory statements within their narratives, reflecting an ambivalence about China and the Chinese. However, because the BOP contributors sought to instil a sense of patriotism, to inspire their readers to serve the British Empire, both the non-fiction travel narratives and the fictional adventure stories related to China were published not only to entertain readers with exotic facts and thrilling stories, but more importantly, to persuade them of the necessity of British intervention. [ABSTRACT FROM AUTHOR]

Since 1990, a large and dynamic global science system has evolved, based on grass roots collaboration, and resting on the resources, infrastructure and personnel housed by national science systems. Euro-American science systems have become intensively networked in a global duopoly; and many other countries have built national science systems, including a group of large- and middle-sized countries that follow semi-autonomous trajectories based on state investment, intensive national network building, and international engagement, without integrating tightly into the global duopoly. The dual global/national approach pursued by these systems, including China, South Korea, Iran and India, is not always fully understood in papers on science. Nevertheless, China is now the number two science country in the world, the largest producer of papers and number one in parts of STEM physical sciences. The paper investigates the remarkable evolution of China's science funding, output, discipline balance, internationalisation strategy and national and global networking. China has combined global activity and the local/national building of science in positive sum manner, on the ground of the nationally nested science system. The paper also discusses limits of the achievement, noting that while China-US relations have been instrumental in building science, a partial decoupling is occurring and the future is unclear. [ABSTRACT FROM AUTHOR]

Economic relationship has been the cornerstone of the China-EU relation as well as the China-EU comprehensive strategic partnership which was established in 2003. On the other side of the coin, economic relations have been main sources of disputes between China and the EU since the 2005–2006 textile disputes. This paper examines their mutual perceptions in this field as one way of explaining the development of the bilateral relationship, supported by substantial empirical data. It is found that the successful economic development of China has generated different perceptions between the EU and China. With the difference in the development level reducing, the EU side was concerned more about the rise of China, while the Chinese side emphasised more the relative decline of the EU's economic might. [ABSTRACT FROM AUTHOR]

As an important foundation of cargo transportation, logistics plays a vital role in developing international trade. Based on the international logistics performance index (LPI) and the sample data of the "Belt and Road" initiative countries from 2011 to 2022, this paper uses the extended trade gravity model to explore the impact of the logistics performance of the "Belt and Road" initiative countries on China's import and export trade. The empirical results show that the improvement of the logistics performance level of the countries along the "Belt and Road" Initiative has a certain role in promoting the growth of China's trade volume to the country, and the improvement of LPI has a more significant positive impact on China's import and export to large-scale countries along the route. Finally, according to the analysis of empirical results, this paper puts forward specific suggestions to promote the development of logistics performance and import and export trade, which provides some reference value for implementing the "Belt and Road" initiative and improving national logistics and trade level. [ABSTRACT FROM AUTHOR]

Cloud model similarity algorithm is an important part of cloud modelling theory. Most of the existing cloud model similarity algorithms suffer from poor discriminability, poor classification, unstable results, and low time efficiency. In this paper, a new similarity algorithm is proposed that considers the triangular cloud model distance and shape. First, according to the D T distance formula, a new exponential closeness measure is defined, with which the distance similarity of cloud models is characterized. Then, the shape similarity is calculated according to the variance of the cloud model cloud drops. Finally, the two similarities are synthesized to define a similarity algorithm for determining the distance from the D T distance formula and shape based on the triangular cloud model (DDTSTCM). In this paper, discriminability, stability, efficiency and theoretical interpretability are taken as the evaluation indices. Equipment security system capability evaluation experiment, cloud model differentiation simulation experiment and time series classification accuracy experiment are set up to verify the effectiveness of the algorithm in terms of the four above aspects. The experimental results show that DDTSTCM has good differentiation and excellent classification effects. In the classification experiment for the time series, the average classification accuracy of DDTSTCM reaches 91.78%, which is at least 2.78% higher than those of the other seven commonly used algorithms. The CPU running efficiency of DDTSTCM is also extremely high, and the average CPU running time of group training is always on the order of milliseconds, which effectively reduces the time cost. Finally, a case study is conducted to analyse a risk assessment problem for China's island microgrid industry, and the evaluation results based on DDTSTCM are in line with human cognition and have good value for engineering applications. [ABSTRACT FROM AUTHOR]

In order to evaluate the beneficiation plant environment in a more scientific and reasonable way, this paper took the workshop environment of the beneficiation plant as the research object. This paper divided the beneficiation plant into 7 evaluation units according to its functions. The evaluation indices are dust, noise, light environment, microclimate, benzene, toluene and xylene. This paper combines the G1 method and the entropy weight method to evaluate the weight of each evaluation index, the element extension model of the concentrator working environment is established by the element analysis method, and the matter element analysis method is used to establish an evaluation index system of a beneficiation plant in East China. The results show that the evaluation level of the breaking workshop and the auxiliary facilities are unqualified, the auxiliary facility is qualified, the culling workshop, culled yard and accessory building are medium, the screening workshop and grinding workshop are good. [ABSTRACT FROM AUTHOR]