Search

Lily bulb is an underground tuber crop, which is mainly grown in southern China. At present, lily bulb harvesting mainly adopts manual excavation, resulting in low labor efficiency. Coupled with the high soil viscosity in lily bulb planting area, there are some problems in lily bulb mechanized harvesting, such as difficulty in fruit-soil separation and high damage rate of lily bulb. In order to solve the problems of poor separation effect, high rate of buried fruit and high crushing rate during lily bulb harvest in sticky soil, a kind of throwing roller lily bulb harvester suitable for operation in sticky soil was designed. The throwing roller lily bulb harvester is composed of vibration conveying device, throwing roller set, excavating shovel and other parts. It has the functions of vibrating crushing soil, throwing crushing soil and material conveying. It can effectively realize the secondary crushing of clay soil, and the separation effect of fruit-soil is good and does not hurt lily bulb, which is very suitable for the mechanical harvesting of lily bulb under the condition of clay soil. Combined with the growth condition of lily bulb and the requirements of planting agriculture, the motion process and separation mechanism of fruit and soil mixture on the vibration conveying device and the throwing roller set were analyzed, the dynamic model of throwing and colliding crushed soil on the throwing roller was established, and the relationship between the structure size of the throwing roller and the crushing of the clay-heavy soil block was established. Through the analysis, the structure and maximum swing Angle of the vibration conveying device, the series of throwing roll sets, the number of throwing roll teeth, the diameter of throwing roll and the contour size and other parameters were obtained. Through theoretical analysis and calculation, the structural parameters of vibration conveying device and throwing roller set of key components were determined. The length of vibration grating rod of vibration conveying device was 150mm, the distance between vibration grating rod was 50 mm, and the swing Angle of vibration grating rod was 59.12°. The number of teeth of the throwing roller wheel was 4 teeth. The radius of the throwing roller wheel was 250 mm. The spacing of the throwing roller wheel was 50 mm. According to the designed structural parameters, a prototype was built and the multi-factor test of operation parameters was carried out. The forward speed of the fruit-soil separation mechanism, the rotation speed of the throwing roller and the digging depth were taken as the test factors, and the embedding rate and crushing rate of lily bulb were taken as the test indicators. Box-Benhnken test method was used to establish the regression equation of factors and test indicators and the influence law of factors on lily bulb harvest index was obtained. When the optimum parameter combination was 0.6 m/s, 90 r/min and 170 mm, the field test values of the rate of buried fruit and the rate of broken lily bulb were 6.3% and 7.1%, respectively. The performance of the machine met the design requirements. The research results can provide reference for the research of mechanization harvesting technology and equipment of lily bulb. [ABSTRACT FROM AUTHOR]

To achieve the carbonization utilization of Triarrhena lutarioriparia straw and relieve the environmental pressure caused by improper disposal in the Dongting Lake area, the agricultural efficiency of biochar derived from Triarrhena lutarioriparia was clarified. Two typical paddy soils in southern China, namely reddish clayey soil developed from a Quaternary laterite parent material and granitic sandy soil developed from a granite parent material, were selected. Six treatments with different dosage of biochar (0, 1%, 2%, 4%, 6%, and 8% of the soil mass，0-20 cm soil depth) were set. Rice pot experiments were conducted in 2020 to study the effects of different application rates of Triarrhena lutarioriparia biochar on rice nutrient utilization characteristics in two typical soils. The results showed different application rates of Triarrhena lutarioriparia biochar and soil types had certain effects on dry matter accumulation and nutrient uptake by rice organs and aboveground structures. With the addition of biochar, compared with the treatment without biochar, the accumulation of dry matter of rice increased from 0.6% to 18.6% and from 15.5% to 42.4% in the granitic sandy soil and reddish clayey soil, respectively. With the addition of 4% biochar, the accumulation of nitrogen, phosphorus, and potassium nutrients in the rice plant of the treatment increased by 8.6%, 10.5%, and 82.5% in the granitic sandy soil and by 33.8%, 100.0%, and 125.3% in the reddish clayey soil, respectively. The quadratic regression equation and fertilizer – carbon coupling model fitting showed that the optimal addition amounts of biochar in the granitic sandy soil and reddish clayey soil were 2.51% and 4.80% for nitrogen utilization, 4.33% and 7.03% for phosphorus utilization, and 4.67% and 4.81% for potassium utilization, respectively. Therefore, the application of Triarrhena lutarioriparia biochar is conducive to promoting the accumulation and growth of nitrogen, phosphorus and potassium nutrients in rice, and the amount of biochar added and soil conditions are important factors affecting the coupling effect of fertilizer and carbon. [ABSTRACT FROM AUTHOR]

Based on the soil temperature and humidity data of soybean farmland under conservation tillage in Northeast China in the published article, the impact of conservation tillage measures on the soil hydrothermal status of soybean farmland in Northeast China was quantitatively assessed by using conventional tillage (CT) as a control, no-tillage (NT), reduced tillage (RT), straw mulching (SM), and no-till straw mulching (NTSM) as treatments. The results showed: compared with CT, conservation tillage increased the soil volume water content of 0-170cm soil layer in soybean farmland in Northeast China by 9.2%, and reduced the temperature of the shallow soil layer (0-30cm) by 8.2%. Four conservation tillage could increase soil moisture under different climatic conditions; straw mulching could increase soil moisture content throughout the growth period of soybeans, and the effect on soil hydrothermal was greatest during the nutrition period of soybean, and soil temperature increased with the increase of straw mulching; the magnitude of soil temperature reduction by conservation tillage decreases with the decrease of soil clay particles, the magnitude of soil moisture increased by conservation tillage decreases with the increase of soil depth. Among them, NTSM at different soil depths was the most obvious effect of water storage and moisture retention, and the soil moisture in the soil layer of 0-20cm was increased by 32.9%. In summary, conservation tillage could increase soil moisture but reduce soil temperatures. Temperature, precipitation, growth period, straw mulching amount, soil type and soil depth all had an impact on soil hydro-thermality in soybean farmland under conservation tillage. [ABSTRACT FROM AUTHOR]

The effects of irrigation on winter wheat yield and water use efficiency (WUE) were mostly explored based on site-based experiments in North China Plain (NCP) region. However, due to the influences of contrasting environmental factors (e.g. climate and soil properties), these results cannot be accurately cross-compared among different studies, resulting in the difficulty to get the generalizable pattern at regional scale. Here meta-analysis was conducted to comprehensively evaluate the effects of irrigation on winter wheat yield and WUE in NCP region, with the observation data of 1876 pairs from 186 field experimental papers totally. The differences of the irrigation effects in different regions, precipitation year types, soil texture, and nitrogen (N) application levels were explored, and the corresponding optimal irrigation amounts for reaching high yield and WUE were ascertained. Results showed that compared with non-irrigation during the winter wheat growing period, irrigation increased the yield of winter wheat in NCP by 32.0%-38.3%, and reduced the WUE by 27.1%-30.1%. The yield increment due to irrigation in the northwest of NCP (39.6%-53.5%) with total precipitation during the winter wheat growing period below 150mm was higher than that in the southeast of NCP (24.3%-27.1%) with total precipitation during the winter wheat growing period higher than 150mm, while the decrease of WUE due to irrigation in northwest of NCP (32.4%-37.5%) was higher than that in the southeast of NCP (22.0%-24.3%). The optimum irrigation amount for high yield and WUE of winter wheat was 150-180mm in the northwest and 120-150mm in the southeast. Specifically, for different precipitation year types, the optimum irrigation amounts were 120-150mm with 2 times during jointing and flowering stages for dry year, during jointing and heading stages for normal year, and during jointing and booting stages for wet year. For different soil texture, irrigation under loamy soil had the highest increases in yield, while clay soil had the lowest decreases in WUE; the optimum irrigation amounts of winter wheat with four different soil texture of sandy soil, loam, clay loam and clay were 60-90mm, 120-150mm, 180-210mm, and 150-180mm, respectively. For different N application levels, N application of 120-240kg.ha-1 led to the highest yield and WUE under the irrigation amounts of 80-140mm, of which the higher yield was obtained under irrigation amounts of 110-140mm, and the higher WUE was obtained under the irrigation amounts of 80-110mm. Collectively, the NCP region can achieve the goals of high yield and WUE when irrigation amount was 120-150mm with 2 times but at different stages during different precipitation year types (i.e. dry year, normal year and wet year). Meanwhile, the combination of loam conditions with the N application of 120-240kg.ha-1 can synergistically improve the yield and water use efficiency of winter wheat. [ABSTRACT FROM AUTHOR]

In order to provide a theoretical basis for the evaluation of carbon sequestration potential, we analyzed the adsorption characteristics and influencing factors of dissolved organic carbon（DOC）in typical farmland soils with different fertilization treatments in China. Four typical farmland soils, namely black soil, gray desert soil, fluvo-aquic soil, and red soil, were selected to apply different fertilizer levels of no fertilizer（CK）, chemical N fertilizer（N）, chemical NP fertilizer（NP）, chemical NPK fertilizer（NPK）, and NPK plus organic manure（NPKM）to determine the DOC adsorption capacities by the equilibrium adsorption method. The results showed that the DOC adsorption capacities of different types of soils at the same equilibrium concentration were very different, and were generally in the order of gray desert soil and red soil>black soil>fluvo-aquic soil.Q max appeared in the order of red soil>gray desert soil>black soil>fluvoaquic soil in various soils. Among them, the adsorption characteristics of each soil type were quite different under different fertilization treatments. The general trend ofQ max in the gray desert soil and fluvo-aquic soil under different fertilization treatments were NPKM>NPK> NP>N>CK and in red soil was NPKM>N>NPK>NP

The sandy clayey purple soil is widely distributed in the middle and upper reaches of the Yangtze River, serving as one of the main soil resources in the mountainous areas of southwest China. Intense physical weathering, loose structure, and low erosion resistance are the main characteristics of sandy clayey purple soil. Therefore, environmental disturbance, such as the water fluctuation near reservoirs, heavy rainfall, and groundwater, often induces soil erosion, landslide, settlement, and soil-water disasters of purple soil. A serious threat has been posed on the village buildings and roads, even the agricultural production. The properties of water immersion disintegration with the sandy clayey purple soil can also be an important reason for water and soil disasters in the southwest mountainous areas. It is necessary to clarify the disintegration characteristics and reinforcement for the water-soil disasters prevention and control. In this study, a disintegration test was performed on the purple soil samples with different initial dry densities, water content, and grain gradation using a self-developed instrument. Meanwhile, the disintegration and evolution of sandy clayey purple soil were also analyzed from the perspective of unsaturated effective stress. Bacillus megaterium was selected to reinforce the soil samples with the Microbial Induced Calcite Precipitation (MICP), as the more suitable as Sporosarcina pasteurii in the sandy clayey purple soil areas. A Scanning Electron Microscope (SEM) was then utilized to characterize the morphologies of the soil sample, thereby determining the MICP improvement on the disintegration characteristics of sandy clayey purple soil. The results show that: 1) Four stages were divided in the whole process of immersion and disintegration of sandy clayey purple soil, including the air-water conversion, equilibrium, disintegration development, and disintegration residual stage. 2) The initial dry density, water content, and grain gradation obviously affected the disintegration characteristics of sandy clayey purple soil. Specifically, the disintegration rate and the average disintegration velocity decreased, with the increase of initial dry density and water content. In addition, the average disintegration velocity of soil increased by the content of fine particles. 3) The evolution of water and air was ranging from the pore water closed, double connected, and pore air closed morphology, with the increasing of the initial saturation. Water was rapidly absorbed into the pores under the matric suction, where the pore pressure was changed significantly. Subsequently, the effective stress of unsaturated soil rapidly reduced to the negative, leading to an interparticle compressive stress (the negative tensile stress). Once the tensile stress reached the value of effective cohesion, the unsaturated strength of purple soil was lost completely. Finally, the soil sample was then destroyed under disintegration. The more severe disintegration was also obtained with the decrease in the initial saturation of a soil sample. The decay process of the unsaturated effective stress depended greatly on the initial saturation after the purple soil was immersed in water. Specifically, the average disintegration velocity attenuated exponentially with the increase of the initial saturation. 4) The disintegration rate and the average disintegration velocity of the MICP treated soil samples decreased by 73 to 97 percentage points and 84%-99%, respectively, compared with the untreated soil. Calcium carbonate crystals formed by solidification and deposition greatly reduced the micro-cracks and large pores in the soil structure. As such, a denser pore structure was achieved to enhance the strength of intergranular cementation for the higher resistance to the disintegration of the soil. Consequently, the MICP technology can serve as an effective measure to prevent the water and soil disasters of the sandy clayey purple soil in southwest mountainous areas. [ABSTRACT FROM AUTHOR]

Soil structure is a key factor to determine the different functions of soil, such as water infiltration and retention, soil permeability, and nutrients availability. The dynamic behavior of soil also depends mainly on the tillage, crop roots, and soil organic matter return. Black soil is one of the most important arable soil with high clay content, but hard soil structure is one of the main factors limiting crop growth. It is still lacking on the effect of organic amendment on soil pore structure in the black soil. In this study, a field experiment was carried out in the black soil region located in Hailun City, Heilongjiang Province of China, in order to clarify the effects of organic amendment and depths on soil physical properties and pore structure before maize sowing in 2019. Four treatments were conducted using random block design with four replicates, including shallow tillage with maize straw return in 0-15 cm soil layer (T1), deep tillage with maize straw return (T2), or combined maize straw and organic manure return (T3) in 0-35 cm soil layer, conventional tillage without organic amendment as control. Maize straw and organic manure were also incorporated into the soil layers by shovel using manual work, where the application rates were 10 000 and 30 000 kg/hm2, respectively. CT scanning was adopted to visualize and quantify soil pore structure after maize harvesting. The constant head method was used to measure the saturated hydraulic conductivity. The results demonstrated that the bulk density under T1, T2, and T3 treatments significantly decreased 3.77%-5.66%, compared with CK, while the saturated hydraulic conductivity increased by 2.2-5.00 times, and the field water capacity increased by 6.91%-11.01% within 0-15 cm soil layer (P<0.05). T2 and T3 treatments also improved the bulk density, saturated hydraulic conductivity, and field water capacity within >15-35 cm soil layer after one maize growing season. Furthermore, the number of soil pores and porosity of >500 μm aperture under T1, T2, and T3 treatments significantly increased by 18.1%-180% and 69.2%-256% (P<0.05) in 0-15 cm soil layer, respectively, compared with CK treatment (P<0.05). Specifically, the soil pore number and porosity of >1 000 μm aperture were more 6.06%-150% and 17.4%-196% under T2 treatment than the rest. It infers that the treatments with organic amendment increased the number of soil pores with optimal distribution. In addition, the complexity and connectivity of soil pore also increased significantly, in presence of connected and sender pore. The Euler number values under T1, T2, and T3 treatments were decreased by 21.7%-54.3%, whereas, the fractal dimension under T1 treatment increased by 1.5% in 0-15 cm soil layer (P<0.05), compared with CK treatment. T2 and T3 treatments improved the soil pore structure in >15-35 cm soil layer, as shown in that the Euler decreased by 65.9%-70.5%, anisotropy, fractal dimension, and circularity increased by 50.0%-110%, 12.8%-13.9%, and 12.2%-14.9%, respectively, compared with CK treatment (P<0.05). The Euler and porosity of >1 000 μm aperture presented the largest contribution both for the bulk density and saturated hydraulic conductivity in 0-35 cm soil layer, whereas, the anisotropy and Euler presented the largest contribution for the field capacity in 0-15 cm and >15-35 cm soil layers. Pearson correlation analysis indicated that the extremely significant negative relationship was found between bulk density and saturated hydraulic conductivity, field water capacity, soil porosity within 0-15 cm soil layer (P<0.01), while the extremely significant or significant correlation was found between bulk density and all indicators, excepting for the anisotropy and Euler. Consequently, the improved physical properties of soil were attributed to the fact that the organic amendment regulated soil structure, including optimal distribution of soil pore, complex, and connectivity of pore structure. Correspondingly, the organic amendment can be expected to serve as an effective approach for the pore structure of black soil. It is also necessary to consider the response of soil pore structure in the decomposition of returned organic manure in the future. [ABSTRACT FROM AUTHOR]

Calcic vertisol is a typical kind of low-yield field with a total area of about 4 million hm2 in China. Calcareous concretion with particle size larger than 2 mm has been one of the representative characteristics of calcic vertisol. The limitation of soil available water is an important reason for crop failure in this region. Therefore, the curve of soil water retention dominates the estimation of available water content. However, most studies focused on the effects of calcareous concretion on soil water retention of calcic vertisol mainly under laboratory conditions. It is lacking that under field conditions. In this study, both field surveys and laboratory experiments were conducted to explore the effect of calcareous concretion distribution in 0-1 m soil profile on soil water retention. Firstly, the spatial distribution of calcareous concretion was investigated in the study plot with 150 m length, 50 m width, and 1 m depth. After then, soil profiles (0-1 m soil depth) were chosen to divide into 5 layers with a 20 cm interval. Disturbed and undisturbed soil samples were collected in each layer. Physicochemical properties were evaluated to measure the distribution of soil particle size, size and content of calcareous concretion, bulk densities of soil, and calcareous concretions. Meanwhile, the curves of soil water retention were determined using high speed centrifuge. A pressure plate method was conducted to measure water retention curves in calcareous concretion. The results showed that the mass contents of clay, silt, and sand were 30.56%-39.75%, 39.88%-45.34%, and 18.67%-24.45%, respectively, which belonged to silty clay soil in the classification standard of the United States Department of Agriculture (USDA). Clayey particles decreased, but sandy particles increased significantly with the increase of soil depth. Calcareous concretion was mainly distributed in the soil depth of >20-100 cm, where the content and size increased as soil depth increased. Calcareous concretions content in the surface soil (0-20 cm) was very low (with mass content 0.02%), where only a few calcareous concretions of 2-5 mm were discovered. The maximum content of calcareous concretion was detected at > 80-100 cm (up to 11.42%), where the calcareous concretion content was 8.04% in the size of >8-30 mm. Soil bulk density ranged from 1.23-1.61 g cm-3. The densities of calcareous concretions were 2.01, 2.21, and 2.23 g cm-3 with the size of 2-5 mm, >5-8 mm, and >8-30 mm, respectively. Soil bulk density increased along with the calcareous concretion content increasing. Water retention curves of soil and calcareous concretion were well fitted by the van Genuchten model, with the determination coefficient larger than 0.95. The saturated water content of surface soil (0-20 cm) was significantly higher than that of 20-100 cm soil. Nevertheless, the Gravitational-water content in the surface soil (0-20 cm) was much larger than that in the soil of > 20-100 cm, which was related to macropores formed during tillage. In the subsurface (>20-100 cm), soil gravitational-water content and available water-holding capacity increased with the increase of soil depth, but the field capacity and wilting point decreased. Calcareous concretion maintained a non-negligible amount of water, 0.25, 0.22, and 0.20 cm3 /cm3 in the particles with the size of 2-5 mm, >5-8 mm, and >8-30 mm, respectively. But the water-holding capacities of calcareous concretion were significantly lower than that of soil. The effects of calcareous concretion on water-holding capacity mainly occurred in the subsurface soil. Soil saturated water content, field capacity, and wilting point decreased with increasing calcareous concretion. Interestingly, calcareous concretion content was positively correlated with the soil sand content, but negatively correlated with the soil clay content. Calcareous concretion can bind soil particles together to prevent sand weathering, and thereby effectively improve soil texture. More calcareous concretion led to higher sand contents, and thus increased the available water-holding capacity in soil. This finding can provide a theoretical basis to accurately assess the soil water-holding capacity in calcic vertisol for precision irrigation and high crop productivity. [ABSTRACT FROM AUTHOR]

Black soil in northeast China is well known as high natural fertility for grain production, but the growth and yield of crop can be limited due to the high clay content of black soil can deteriorate physical properties. In this case, both tillage and straw return can be expected to serve as the important agronomic practices, in order to efficiently improve soil physical properties. However, the optimal depth of tillage and straw return into soil for favorable soil physical properties still remained unknown, particularly in black soil region. In this study, a field experiment, referred to the depth of tillage and straw return into soil, was conducted for six years in the black soil region in northeast China, in order to investigate the effects of incorporation depth of tillage and straw return into soil on soil physical properties of black soil. Seven treatments consisted of four replicates and random block design, including no tillage (D0), shallow tillage (0-20 cm) without or with straw return (D20 or D20S), deep tillage (0-35 cm) without or with straw return (D35 or D35S), super deep tillage (0-50 cm) without or with (D50 or D50S) straw return. In the treatments with straw return, a straw rate of 10 000 kg/hm2 was set to return into the corresponding tilled soil layer. Bulk density and water holding capacity were measured using cutting ring method, while the hydraulic conductivity was determined using constant head method, and the aggregate was measured using wet sieving method. The results showed that: 1) Compared with initial soil values, D0 treatment significantly increased soil bulk density, while decreased soil porosity, water holding capacity, hydraulic conductivity and >0.25 mm water stability aggregate (WAS>0.25) within 0-20 cm soil layer (P<0.05). However, there was no significantly impact on those indicators in soil layer within 20-50 cm (P>0.05). 2) In D20, D35 and D50 treatments, there was no obvious impact on the soil physical properties within 0-20 cm soil layer with exception for WAS>0.25 in D50 treatment, but D20S and D35S treatments remarkably all indicators of soil physical properties within 0-20 cm soil layer. 3) D35, D35S, D50 and D50S treatments significantly improved soil physical properties within >20-35 cm soil layer with exception of bulk density in 2014, while D50 and D50S treatments dramatically enhanced soil physical properties within in >35-50 cm soil layer (P<0.05). Specially, aeration porosity and hydraulic conductivity increased significantly, within the corresponding soil layers, while the higher effect was found in the treatment with straw return, compared with only tilled treatments. The comprehensive evaluation also showed that D35S and D50S treatments reached the best effect for improving soil physical properties. Therefore, the findings demonstrated that deep tillage or super deep tillage with straw return can efficiently improve soil physical properties within the whole tilled soil layers, concurrently to increase the depth of tilled soil layer, and thereby to enhance the water infiltration rate and soil water storage in black soil with heavy clay. In view of the positive effect of deep tillage and super tillage with straw return on soil physical properties and the limit of no tillage, the combined tillage practices of deep tillage (or with straw return) and no tillage were proposed for the black soil with high clay in northeast China and other regions. [ABSTRACT FROM AUTHOR]

Rice-wheat rotation area, with heavy clay soil texture, that it is wheat planting area accounts for more than 37% of the total wheat sowing area in China as one of the major grain production bases, and rice-wheat rotation is the main cropping pattern in this region. Meanwhile, because of the shortage crop stubble and more rainfall in autumn, which lead to serious wet damage during the tilling and seeding stage for this field. Currently, most of the existing no-tillage and less-tillage seeding equipment for wheat sowing in rice stubble areas were optimized and developed on the basis of traditional contact-type wheat seeding technology, which lead to adhesion and serious blockage phenomenon, as well as increasing of operating resistance and power consumption during working. Therefore, a innovative technical proposal of non-contact type pneumatic seeding technology that could avoid contacting between sowing parts and soil was introduced in this paper, which in order to solve the problems of soil adhesion, blockage, drag increment as well as poor sowing quality for wheat seeders under the condition of sticky heavy loam clay in rice-wheat rotation areas. Experiment that utilized a self-made platform for wheat pneumatic seeding was conducted, which could rip wheat seed into the soil condition of clean seed bed without straw and stubble mulching by high pressure accelerating airflow. During the pneumatic seeding experiment, keeping a certain pneumatic seeding height HG and incident angle α between the accelerating tube and topsoil surface, high-pressure gas was injected from the upper apex of the air nozzle and ejected from the bottom of it, which a stable high-speed airflow was formed in the accelerator tube (the length of the accelerator tube is 600 mm and the diameter is 10 mm). Then wheat seeds were put into the seed entrance and absorbed at a high speed under the negative air pressure of the ejector, during which the rubber sleeve could protect wheat seeds from damaging. After mixing with airflow, wheat seeds were accelerated by high-speed air flow in the accelerating tube. Finally, the wheat seeds flew out and ripped into the soil at a certain incident angle and high pneumatic seeding velocity. At the same time, high-speed photography technology was used to study the parameters of pneumatic seeding velocity, vertical velocity and pneumatic seeding depth under six levels (15°, 30°, 45°, 60°, 75°, 90°) of incident angles, and pneumatic seeding experiments under five different accelerating air pressures of 0.2 MPa, 0.4 MPa, 0.6 MPa, 0.8 MPa and 1 MPa for each incident angle were carried out respectively. Pneumatic seeding experimental results showed that: For pneumatic seeding in soil without straw and stubble mulching, when the incident angle increases continuously, wheat seeds can achieve higher vertical component of pneumatic seeding velocity deeper and pneumatic seeding depth at the same accelerating air pressures, the probability of horizontal slip and bounce of wheat seeds after touching soil show an decreasing trend, and pneumatic seeding depth has a positive correlation with pneumatic seeding velocity under each incident angle. Moreover, wheat seeds show various pneumatic seeding depth and soil impact effect without damage after pneumatic seeding. When the incident angles and the vertical component of pneumatic seeding velocity were more than 45° and 25 m/s respectively, wheat seeds can be completely ripped into the soil and the emergence rate is more than 86%. The best pneumatic seeding effect achieved as incident angle is 90°. In order to realize wheat vertical pneumatic seeding in field operation, the horizontal component of pneumatic seeding velocity should be equal to the operating speed of seeder and the vertical component of pneumatic seeding velocity should be greater than 25 m/s, which the seeder operating speed shows positively and negatively correlated with pneumatic seeding velocity and incident angle, respectively. The experimental results can provide basic data and technical support for the development of non-contact wheat seeding equipment in rice-wheat rotation area. [ABSTRACT FROM AUTHOR]

In order to obtain the interaction parameters which can be used for discrete element simulation between the soil-engaging components and clayey black soil in northeast China, the Hertz-Mindlin with JKR Cohesion contact model in EDEM2.7 was used to simulate the clayey black soil. Aiming at the actual working environment with moisture content of 10%-20%, 2 kinds of clayey black soil with moisture content of 12.46%±1% and 17.15%±1% were prepared respectively. The rolling friction coefficient, recovery coefficient, JKR surface energy parameter and the static friction coefficient between the soil particles were used as the model calibrated parameters. The soil repose angle simulated under the simulation parameters was set as the response value. The regression model of the soil repose angle was established based on the Box-Behnken response surface method, and the regression model was optimized by using the soil repose angles under 2 moisture contents obtained by physical experiments. The optimal solution of the contact model parameters of the clayey black soil particles with 2 moisture contents was obtained. The parameter range of the discrete element contact model of clayey black soil with moisture content between 10%-20% were given. The soil repose angle and stacked shape obtained by the simulation experiment with the optimized solution had a high similarity with that of the physical test. At the same time, the static friction coefficients of 3 kinds of soil contact materials such as 65Mn plate, UHMW-PE plate and PTFE plate were tested under the conditions of 4 kinds of moisture content, which were 0, 12.46%, 17.15% and 23.5% respectively. Then for the 2 typical soil contact materials such as 65Mn and PTFE, the slope physical test bench were constructed for the clayey black soil with moisture content of 17.15%±1%. The slope simulation models of 65Mn and PTFE materials were established under the EDEM2.7 software platform. Based on the critical simulation parameters such as JKR surface energy parameter, static friction coefficient, rolling friction coefficient and recovery coefficient between soil particle and soil contact material, the simulated rolling distance of the soil ball on different soil contact materials was set as the response value. The excellent fit regression model of rolling distance for the 2 kinds of typical soil contact materials were established based on the response surface optimization method of Box-Behnkende. The 2 regression models were optimized by the sliding distance obtained by the physical experiment. Then the optimized solution of the contact model parameters of different materials was obtained. The simulation results showed that when the surface energy of JKR between soil and 65Mn was 5.5 J/m2, the recovery coefficient was 0.61, the static friction coefficient was 0.57 and the rolling friction coefficient was 0.056, the rolling distance simulation result was 153.56 mm, which was close to the average rolling distance obtained from physical experiments of 155.93 mm, and the relative error was 1.52%; When the surface energy of JKR between soil and PTFE was 4.08 J/m2, the recovery coefficient was 0.6, the static friction coefficient was 0.52 and the rolling friction coefficient was 0.045, the simulation result of rolling distance was 269.35 mm, which was close to the average rolling distance of 269.55 mm obtained from physical experiment, and the relative error was 0.07%. And the optimized parameters can be used to simulate the discrete parameters between the clayey black soil and the soil-engaging components. The study provides credible basic data for the design and simulation of agricultural machinery under clayey black soil conditions. [ABSTRACT FROM AUTHOR]