Search

Cotton, one of the main commercial crops in the world, mostly distributes in several major growing regions, including Xinjiang of western China. An important renewable biomass resource, the cotton stalk has received most attention to serving as the poultry feed, paper making, environmental protection materials, and biomass briquette fuel. Particularly, the highly efficient recycling of cotton stalk can be widely expected to bring enormous economic and ecological benefits. However, most previous treatments are focused on pulverizing cotton stalks and returning to the field. A great challenge is still posed on the current pulling machines for cotton stalks, with emphasis on operational requirements, leakage, and breaking rate. In this study, a novel horizontal-roller cotton stalk pulling machine was proposed to efficiently implement the pulling of the whole cotton stalk after harvesting. The machine was mainly composed of traction, gearbox, stalk conveying, transmission system, machine body, road wheel, spacing regulating mechanism, stalk pulling, dam-board, and support frame. Specifically, the power input shaft of the gearbox was connected to the power output shaft of a tractor. In working, the power was transferred to the chain drive by the power output shaft of a gearbox, and then to realize the stalk conveying and pulling operation under the rotation of the toothed belt and the opposite rotation of the stalk pulling roller. A systematic kinematic analysis was conducted to determine the influencing factors in the working process. A field test was also carried out in a farmland in Korla City, Xinjiang Uygur Autonomous Region of China in October 2019. The soil firmness was 467 kPa, and the moisture content of the soil was 15%-20%, due to the perennial drought and little rain in the study area. The average height of cotton stalk was 700 mm, while, the plant spacing was 50 mm in a wide and narrow close planting mode. The power was from a CFD604A wheeled tractor with a calibrated power of 44.2 kW. The test was performed on the national standard of a harvester combine test(GB/T 8097-2008). A three-level quadratic regression orthogonal test was designed, where the forward velocity of the machine, the rod velocity of the deflector, and the speed of the stalk pulling roller were selected as the influencing factors, whereas, the leakage rate and plucking rate were the response factors. A response surface method was utilized to establish the regression equations for the relationship between the factors and assessment indexes. An optimal combination of parameters was obtained, while an experiment was also conducted to verify the mathematical model. The test results demonstrated that there were great effects of factors on the performance of horizontal-roller cotton stalk pulling. The significant effects on the leakage rate were ranked in a decreasing order: the forward velocity of the machine, the rod velocity of the deflector, and the speed of the stalk pulling roller. Correspondingly, the significant effects on the plucking rate were ranked in a decreasing order: the speed of the stalk pulling roller, the rod velocity of the deflector, and the forward velocity of the machine. The verification test indicated that the leakage rate of the cotton stalk was 5.24%, and the plucking rate was 3.75%,when the forward velocity of the machine was 0.68 m/s, the rod velocity of the deflector was 1.75 m/s, and the speed of the stalk pulling roller was 221 r/min. The optimal combination was better consistent with the predicted one in model optimization, indicating a reasonable structural design. The findings can provide a sound reference for the structural design and optimization of operation parameters in the horizontal-roller cotton stalk pulling machine. [ABSTRACT FROM AUTHOR]

Copyright of Rolling Stock (1002-7602) is the property of Rolling Stock Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Rolling Stock (1002-7602) is the property of Rolling Stock Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The banana stalks are rich in fiber, and the existing returning machines for banana straw and stubble crushed in China have generated a few problems such as overly severe cutting resistance, the fiber of banana straw winding crushing blade roller on the returning machine, working on the unstable condition and serious fuel consumption. In order to deal with the above problems which the existing choppers met with in the working process, with the help of theoretical study and the analysis on the planting model for banana in Hainan Province, this paper put forward a returning method that the moving knives on the front knife roller were used to crush banana straws and the flail knives on the back knife roller were used to break stubble under the earth. The rotational direction of stubble crushing roller in the returning machine was same to the forward direction of the machine providing power, while the rotational direction of straw crushing roller was contrary to that of stubble crushing roller. On the basis of establishing theoretical model and the analysis on the planting model for banana in southern China, the key shaped parameters of the sliding-cutting blade and the structural parameters of crushing blade rollers were determined respectively. Besides, the sliding-cutting and anti-twining returning device for banana straw was put forward. The overall structure and working principle of sliding-cutting and anti-twining returning device were described. The performance of crushing banana straw and the power consumption were evaluated by simulating the breaking operation of banana straw in farmland through a bench test driven by double electric motors. The machine was composed of electrical motors, a tractor powered by electricity, the frame of machines, the straw crushing device and the stubble crushing device. Through Design-Expert software, a quadratic orthogonal rotating experiment was performed. Based on the variance analysis and regression fitting, a multiple regression equation was gained, presenting the effects of the working speed of the returning device, the rotating speed of rotating roller of moving knives and the rotating speed of rotating shaft of stubble breaking on the qualified rate of straw crushing and power consumption. It could be seen that the rotating speed of rotating roller of moving knives had the most influential effect, followed by the rotating speed of rotating shaft of stubble breaking, and the working speed of the returning device had the least influence on the qualified rate of straw chopping. The operation condition was optimized by applying the response surface method. The optimum factors for straw and stubble crushing process were as follows: The rotating speed of rotating roller of moving knives was 1 600 r/min, the rotating speed of rotating shaft of stubble breaking was 500 r/min, and the working speed of the returning device was 1.39 m/s. Based on the theoretical analysis, the higher qualified rate of straw crushing was achieved under the faster rotating speed of rotating roller of moving knives. The smaller power consummation was obtained under the lower rotating speed of rotating roller of moving knives and the lower rotating speed of rotating shaft of stubble breaking. Under the optimal condition, the corresponding qualified rate of straw crushing and power consumption were 95.2%, and 4.96 kW, respectively. The differences between the experimental and the analytical values of the qualified rate of straw chopping and power consumption were 0.31 percentage points and 0.27%, respectively, which indicated that the software analytical value was in great agreement with the experimental value. And by field test, qualified rate of straw crushing of machine proposed in this paper was higher by 1.94 percentage points and power consumption was lower by 11.3%, compared with vertical flail banana stalk crushing machine. Its successful implementation can greatly improve the production efficiency for crushing banana straw and stubble on one hand, and on the other hand prevent the pollution brought by deserted banana straw putridity. [ABSTRACT FROM AUTHOR]

Residual plastic films degrade soil structure and have a detrimental impact on seed germination and the subsequent seedling development and establishment, thereby leading to reductions in crop yield. Removing the films from soil prior to sowing is hence critical to safeguarding crop growth. This paper presents a roller-type device incorporated into ploughing machine to simultaneously strip, collect the films from the soil and then unload them in a row prior to sowing. The device was nail-teeth designed to pick up and strip the residual films. The optimal combination of the structure and working parameters of the device was theoretically analyze using a quadratic regression orthogonal rotation test by taking forward speed of the machine, rotating speed of film pick up roller and rotating speed of film stripping shaft as determinants, and the efficiency of both film pick up rate and film stripping rate to represent the performance of the device. The significance of each determinant in affecting the rate of film pick up and stripping was analyzed using the Design-Expert software. The results show that in terms of impact on film pick up rate, the three determinants were ranked in the order of machine forward speed > rotating speed of film pick up roller > rotating speed of film stripping shaft, while in terms of impact on film stripping rate, the determinants were ranked in the order of rotating speed of film stripping shaft > rotating speed of film pick up roller > machine forward speed. Optimization calculated using MATLAB showed that the optimal working parameters were: device forward speed 1.62 m/s, rotating speed of film pick up roller 90 r/min, and rotating speed of film stripping shaft 1 055 r/min. We verified these optimal results against field experiments and found that the film pick up and film stripping rate was 70.56% and 82.96%, respectively. The differences between the experimental results and the calculated results was small, indicating that the optimized working parameters were reliable and robust. [ABSTRACT FROM AUTHOR]

In order to solve the problem that seedlings cultivated by pie-shaped compression matrix can not be planted by the existing transplanter, a semi-automatic compression matrix seedling transplanter was designed in this paper by mimicking the artificially transplanting method of putting seedlings after punching a hole. The compression matrix type seedling transplanter mainly consists of a ground wheel, a swing mechanism, a ratchet wheel, a hole puncher, a displacement mechanism, a seedling clamping mechanism, a conveying device, a transmission system, a rack, and so on. The physical dimensions and mechanical properties of the compression matrix type seedling are the key basis for the design of the seedling planting schemes and structures. Taking watermelon seedlings as the research object, the dimensions of the seedlings were measured, and the friction coefficient of the compression matrix with different water contents and the compressive strength of the compression matrix were determined. The coefficients of friction between the slideways and the flanks of watermelon seedlings with 2 groups of different water contents were determined to be 0.755 and 0.634 respectively by single-factor tests. The relationship between the compression load and the compression amount of the 2 groups was also analyzed. When the load is 0-5 N, as the surface of the seedling is in point contact with the semi-circular thin metal at the initial stage of compression, the compression load increases evenly and the amount increases rapidly. When the load is between 5 and 20 N, as the surface of the seedling is in surface contact with the semi-circular thin metal, the compression load increases evenly with less impact on compression. When the load is greater than 25 N, some external cracks are observed on the surface of the seeding during the test. Comparing the 2 tests, it can be seen that the seedling with high water content is not easily destroyed. The swing mechanism is optimized according to the known movement law of the initial angle of the crank and the output angle of the driven rod. The dimensions of optimized parts are 57, 161, 79 and 170 mm, respectively. When the crank rotates one revolution of 360°, the reciprocating swing angle of the driven rod is 92.3°, which satisfies the working requirements of the four-equal-part ratchet wheel mechanism. The structure and specific size parameters of the hole puncher are determined according to the measurement size and planting depth requirements of the watermelon seedling. The width of the edge surface is 1.5 mm. The inner diameter of the small end is 64 mm, and the height of the tapered part of the hole puncher is 65 mm, and when the incision angle is 21°, the inner diameter of the big end is about 114 mm. The structure parameters of the seedling clamping mechanism are determined according to the mechanical properties and the dimension of watermelon seedling. And it is also concluded that the seedling’s matrix can overcome the self-gravity of the seedling, which ensures that the seedling clamping mechanism can securely grip the seedlings when transplanting with a clamping force of 26 N. The seedling conveying device and the planting holding device are driven by the same power source, ensuring that the feeding speed of the seedlings is synchronized with taking seedling action of the planting holding device. The conveyor belt is used to transport the seedlings, and the conveyor belt was designed to send seedlings at a speed of 40 plants per minute. Using a compression matrix for field planting functional verification tests, the average plant spacing is 98.6 cm when the transplanter moves at a stable speed of 2.1-2.6 km/h. The pass rate of the plant spacing is 90.62% and the lodging rate is 21.9% which is slightly higher. In the follow-up study, dual-ground-wheel driving would be used to improve the reliability of the transmission and obtain uniform spacing; a hole shape with the same level and the same depth should be acquired, and the lodging rate after the landing of pie-shaped matrix would be reduced by increasing the copying mechanism and optimizing the shape and structural parameters of the hole puncher. [ABSTRACT FROM AUTHOR]