Search

Ultra high frequency (UHF) partial discharge (PD) detection is a common method for transformer oil-paper insulation defect location. However, the accuracy of PD positioning in practical application is easily affected by noise and sensor layout. In order to ensure the effectiveness of PD positioning detection of transformer oil-paper insulation defect, an UHF PD positioning detection platform for oil-paper insulation defects is established. Based on the conventional K-means method, a modified clustering demarcation PD anti-interference positioning method is proposed, which effectively reduces the positioning error. Aiming at the problem of sample clustering demarcation aliasing, when the optimal correction coefficient L is 1.1, the UHF PD positioning error can be reduced to less than 0.1 m, which verifies the effectiveness of the proposed method. Finally, the variation law of positioning error of different sensor layout is analyzed, and the optimal layout scheme of UHF sensor for transformer oil-paper insulation defect detection is proposed, which can provide reference for the layout and positioning of transformer on-line monitoring sensor.

A new method was proposed for point-of-care testing (POCT) of immunosuppressants in blood using thin-layer paper spray ionization and a miniature mass spectrometer. The aluminum thin-layer plate was used as paper spray substrate, and cut into an equilateral triangle. Aliquots of 10 μL blood sample were loaded on the aluminum thin-layer plate, and then 20 μL methanol was dropped as elution/spray solvent. The tip of the triangular plate was placed 1.0 cm in front of the discontinuous atmospheric pressure interface (DAPI) of the miniature mass spectrometer. When the spray voltage was applied, the sample was eluted from the triangular plate and formed paper spray ionization at the tip. Coupled with the miniature mass spectrometer, five immunosuppressants were detected under negative ion mode. The precursor ions ［M-H］- of tacrolimus, sirolimus, everolimus, ciclosporin A, and mycophenolic acid are m/z 802.6, 912.6, 957.1, 1 200.8, 319.1, and product ions are m/z 560.2 and 604.3, m/z 590.3 and 321.2, m/z 590.3 and 365.2, m/z 1 088.8, m/z 287.4 and 275.1, respectively. Based on the observed signal-to-noise ratio (S/N) of the most intense tandem mass spectrometry (MS/MS) fragment peaks and using the S/N=3 and 10 as the criteria, the limits of detection (LODs) and quantitation (LOQs) are estimated to be 0.5-5 mg/L and 1-10 mg/L, respectively. The internal standard method was used for quantitative analysis, and indapamide was used as the internal standard compound. Sufficient linearity for each analyte is obtained with the correlation coefficients (r) greater than 0.99. The proposed method displays good recoveries in the range of 91.0%-114.3% with the relative standard deviations (RSDs) less than 8.4%. Moreover, the developed method was used for the analysis of blood samples, which spiked with tacrolimus, sirolimus, everolimus, cyclosporine A and mycophenolic acid at the concentration of 100 mg/L. The analytical results demonstrated the consistency between the proposed method and the traditional liquid chromatography-mass spectrometry (LC-MS) method. The entire analysis procedure can be completed within 1 min. The proposed method is simple, fast, accurate, efficient, and suitable for POCT of immunosuppressants in blood.

BackgroundIn recent years, the rising number of e-cigarette users among adolescents and the surging cases of lung injury related to e-cigarette use have attracted the attention of researchers in various fields.ObjectiveTo identify the research hotspots and trends of e-cigarette or vaping product use associated lung injury (EVALI) worldwide from 2013 to 2022 by bibliometric and visual analysis. MethodsWeb of Science Core Collection was selected to obtain literature related to EVALI from 2013 to 2022 across the world, statistics were calculated by country/region, institution, author, journal, cited literature, keyword, etc. CiteSpace 6.2.R1 was used for visual analysis to draw diagrams of publication trend, author cooperation network, co-citation clustering time distribution, and keyword cluster. ResultsA total of 888 EVALI-related papers published between 2013 and 2022 were retrieved. The number of publications was gradually increased, with a significant increase in 2020 and a decrease from 2021, but the number of citations was increased year by year. The most active country was the United States (631 articles). European and American countries cooperated closely and the centrality was prominent. Among the publishing institutions, the University of California system topped the list with 103 articles. Rahman I (27 articles) published the most articles and had a high degree of centrality; Goniewicz M L was the most cited author; and the network analysis diagram showed relatively weak collaboration between authors. The American Journal of Respiratory and Critical Care Medicine was the journal with the highest number of publications (94 articles). The top 5 cited articles were all cited more than 300 times. The leading high-frequency keywords of EVALI-related studies were nicotine (149 times), exposure (118 times), and oxidative stress (80 times). The cluster of key nodes in the co-citation network and the clustering time distribution diagram indicated youth e-cigarette addiction received widespread attention from society. From the top 25 keywords with the strongest bursts, the focus of research on the pathogenesis of EVALI gradually shifted from the oxidative stress damage associated with e-cigarette vapor to the oxidative effect of flavoring chemicals in the process of lung injury. The current research interests in this field were mainly the mechanisms of various chemicals in e-cigarettes and the heating elements that led to damage to the lungs. ConclusionEVALI is receiving continuous attention from researchers in government, medical institutions, and other organizations. A variety of e-cigarette ingredients such as flavoring chemicals may lead to varying degrees of cytotoxicity, inflammation, and lung damage. However, the pathophysiology of EVALI remains unclear. In the future, more Chinese scholars should be encouraged to participate in this field.

Based on the selective quenching effect of the flavonoid rutin on the fluorescence of carbon dots prepared by asparagine pyrolysis, a method for rapid detection of rutin content in the flower buds of Sophora japonica by using chitosan-based carbon dot paper chip was developed. A filter paper was immersed in the casting solution of carbon dots and chitosan. After drying, a carbon dot chitosan film was formed on the surface of the filter paper, so that the chitosan-based carbon dot paper chip was obtained. After samples were dripped on the chip, chromogenic reaction occurred uniformly within a limited region, and pictures were taken under an ultraviolet (UV) lamp at 365 nm for analysis of the red (R), green (G), and blue (B) values of the colored spots in order to optimize the preparation conditions and detection conditions. The results showed that the optimal conditions were as follows: chitosan concentration of 20 mg/mL, carbon spot concentration of 1.0 mg/mL, 50% ethanol as sample solvent, and reaction time of 20 min. Under these conditions, the difference (ΔG) in G-value between sample and solvent spots had a linear relationship with rutin concentration (C) in the range of 4 to 120 mg/mL. Using this method, the average contents of rutin in the flower buds of S. japonica from three batches were determined to be 23.85%, 22.83% and 20.30%, the average relative standard deviations (RSDs) were 6.1%, 5.6% and 6.7%, and the recoveries were 91.27% to 107.5%, which were close to the results of high performance liquid chromatography (HPLC). The proposed method is simple and rapid, and can be used for rapid on-site determination of rutin content in the flower buds of S. japonica.

Results of academic research require publication and need to be reviewed by peers before they can contribute to the existing body of knowledge. Among the various means of publishing research findings, researchers may, according to past academic practices, first present their research results in conferences, seminars or symposiums, and then submit their results to journals for publication. Hence, the issue of “extended publication”, where conference papers are revised and submitted to journals, has gained attention in the library and information science community. This study collected public documents on the Internet and applied document analysis to examine the ethical considerations regarding such extension practice. First, this research reviewed the basic principles of research integrity and responsible behavior. Secondly, this research listed several types of violation related to research paper writing and submission, and studied the guidelines established by both domestic and foreign academic organizations, publishers, and journals. The findings of the research were used to provide specific recommendations on the best practices for extending conference papers to journal articles.

To explore the microscopic mechanism of thermal stability of oil-paper insulation， a molecular model consistent with the actual oil-paper insulation is established. Through comparison with the experimental results， the effectiveness of the model is verified. With temperature as an independent variable， variation of the mechanical parameters and hydrogen bond energy of the cellulose molecular model under the action of a thermal field is investigated. The results show that parameters characterizing the mechanical properties of cellulose， such as bulk modulus （K）， Young's modulus （E）， shear modulus （G）， and Poisson's ratio （v） of the cellulose crystalline zone model are larger than those of the amorphous zone model at the same temperature， and the distribution of hydrogen bond energy remains the same. Thus， the cellulose crystalline zone is superior to the amorphous zone in mechanical properties and determines the insulation properties of cellulose insulating paper. The results of the study provide a theoretical basis and method for investigating the microscopic mechanism of thermal aging of oil-paper insulation.

The insulation performance of transformer bushings is a crucial aspect that directly affects the safe operation of equipment. To diagnose the insulation status of transformer bushings and mitigate the impact of small-sample imbalanced data on diagnostic results, a particle swarm optimization combined with back propagation neural network (PSO-BPNN) and adaptive synthetic sampling (ADASYN) method are employed to fault diagnosis of transformer bushing. Initially, historical fault data of transformer bushings are gathered, and a sample set of dissolved gases in transformer oil with distinct fault categories is established. The ADASYN algorithm is used to synthesize the minority class samples in the original data, which allowed for obtaining balanced fault data. The balanced dissolved gases in oil served as the model input, and the fault status is used as the label output to diagnose the transformer bushings using the PSO-BPNN model. To diagnose the bushings under the original sample set, the back propagation neural network (BPNN), genetic combined with back propagation neural network (G-BPNN), cuckoo search combined with back propagation neural network (CS-BPNN), and PSO-BPNN models are used. The results reveal that the PSO-BPNN model based on ADASYN balanced data exhibited the highest accuracy among the various models for fault diagnosing the insulation status of transformer bushings. This approach effectively mitigate the impact of small sample imbalanced data on diagnostic results, and provide an effective method for assessing the insulation performance of transformer bushings.

[Purpose/Significance] Interdisciplinary research can creatively solve complex problems in natural environment and human society through knowledge integration and penetration. With the increase of interdisciplinary research results, the evaluation of interdisciplinarity becomes increasingly necessary. How to establish an effective method for interdisciplinarity measurement and achieve a comprehensive measurement of scientific research papers is an urgent problem to be solved. [Method/Process] Based on the above background, this study takes the data of scientific research papers as the analysis source, deconstructs the interdisciplinarity of scientific research papers from multiple dimensions, constructs the feature set of interdisciplinarity of scientific research papers, and on this basis proposes the method for measuring interdisciplinarity based on the adaptive method of machine learning, and conducts a comprehensive measurement of interdisciplinarity. This study has certain positive significance for researchers to understand the interdisciplinary papers in the field. The work process is as follows: First of all, the basic concepts of interdisciplinarity are sorted out and related concepts are discriminated, and the index of interdisciplinarity of different dimensions is analyzed. Based on the connotation and characteristics of interdisciplinary research, the characteristic index of interdisciplinarity of scientific research papers is extracted from three dimensions: subject attribute, knowledge network topology and knowledge integration text content. Secondly, an interdisciplinarity measurement method based on machine learning is constructed. By analyzing information gain and feature similarity of input indexes and data in feature sets, a feature selection calculation method based on adaptive feature selection is proposed, and the accuracy of feature classification is maximized by machine learning classifier. At the same time, the feature subset that can best express the interdisciplinary is selected based on the adaptive selection of the minimum number of features, and the selected adaptive feature set is used in the calculation of the interdisciplinary of the paper, and the results of the calculation of the original feature set are analyzed comprehensively. Finally, an empirical study was carried out in the field of plant nanobiotechnology to verify the effectiveness of the index system and adaptive feature selection listed above, identify and screen papers with high interdisciplinarity in the field, measure the interdisciplinarity of papers and identify key influencing factors based on the calculation of subject attributes, knowledge network topology and knowledge integration text content features. [Results/Conclusions] The main empirical results show that, among the subject attributes, the balance degree and the difference degree have a greater effect on the interdisciplinary evaluation. The overall effect of knowledge network topology structure features is satisfactory, the distribution breadth of knowledge integration text content features has a greater effect on interdisciplinary evaluation, and the calculation effect is further improved by fitness weighted summation of each feature. The results demonstrate that the adaptive feature selection proposed in this paper can effectively screen the interdisciplinary related feature indexes, improve the reliability of the results, and achieve a comprehensive and in-depth measurement of the interdisciplinary of scientific research papers. This measure method avoids the subjective defects that may occur in qualitative evaluation and the problems that different measure indicators may produce contradictory results. It provides a new idea and direction for interdisciplinary measurement.

New paper-based microfluidic technology has been widely used in many fields due to their advantages such as easy preparation, low cost, and non-toxic environmental protection, compared with the shortcomings of other food analysis and detection techniques such as complex production method and high cost of preparation. The outline of new paper-based microfluidic technology is briefly summarized and the probes including organic molecules, nanomaterials and polymers their structural activity with regard to sensing performances along with their limit of detection are also discussed. This review is expected to assist readers for better understanding of the sensing mechanisms of various chemo and bio-probes utilized in µPADs, as well as promote their advancement in the field. The detection mechanism and its advantages in the whole detection system at the same time to get the ideal experimental results of new paper-based microfluidic technology in the food analysis of pesticide residues, pathogenic bacteria, additives, heavy metals and other substances are mainly introduced. This study would provide the theoretical basis and references for fast detection field. The future challenges and application prospects of this technology are prospected.

“Lab on paper” is a paper-based microanalytical system with unique advantages such as high sensitivity, low cost, portability, and mass production, which breaks through the limitations of traditional detection technologies and shows great potential in the field of rapid on-site food detection. In this paper, the typical “labs on paper”, including chromatographic paper, chemical test chip, lateral flow assay (LFA), microfluidic paper-based analytical devices (μPADs), and synthetic biological paper, are systematically reviewed. Special emphasis is put on the application of “lab on paper” in the field of food detection. Finally, the advantages, challenges, and future prospects of paper-based analytic methods are discussed, which may provide theoretical support for better application of “lab on paper” in the field of food detection.

Fruit paper is a paper-shaped snack made from fresh fruit after pulping, boiling and drying. Drying, one of the oldest methods for food preservation, removes water from fruit and extends its shelf-life for year-round consumption. The most commonly used drying methods include hot air drying, vacuum drying, freeze drying, and their combinations. The energy efficiency of drying process and the quality of fruit paper are both important to be considered in fruit pulp drying. This article updates the research status of drying technologies applied in fruit paper production, including hot air drying, freeze drying, vacuum drying, microwave drying, infrared radiation drying, and refraction window drying. In addition, the influence of the pretreatments and drying process on fruit paper's shape, texture, and nutrients are also summarized. This work aims to improve the drying efficiency of fruit paper and retain the active ingredients of fruit to the maximum extent, and to provide reference for further research on drying processing of fruit paper in food industry.

Knowledge representation of scientific paper data is a problem to be solved,and how to learn the representation of paper nodes in scientific paper heterogeneous network is the core to solve this problem.This paper proposes an unsupervised cluster-level scientific paper heterogeneous graph node representation learning method(UCHL),aiming at obtaining the representation of nodes (authors,institutions,papers,etc.) in the heterogeneous graph of scientific papers.Based on the heterogeneous graph representation,this paper performs link prediction on the entire heterogeneous graph and obtains the relationship between the edges of the nodes,that is,the relationship between paper and paper.Experiments results show that the proposed method achieves excellent performance on multiple evaluation metrics on real scientific paper datasets.

The academic journals of meteorological science and technology of China take the solicitation of review meteorological scientific and technological paper (RMSTP) as an important way to improve their core competitiveness and bibliometric evaluation indicators. Therefore, high-quality RMSTPs are favored by journals, and many scientists are also stimulated to write RMSTP. In order to advise the authors to write a successful RMSTP, this paper first introduces the four principles of the topic for RMSTP, and divides RMSTP into two types: overview type and discussion type. It highlights the importance of writing motivation and the scopes of time, space, and topic for RMSTP, and provides the suggestion about how to express them properly in the paper. Meanwhile, taking three RMSTP's published in recent years as examples, this paper focuses on the problems that should be paid attention to in the text structure and its content expression, summary writing, and literature citation of RMSTP. Finally, it points out that writing a successful RMSTP requires the author to read large number of literatures and have rich scientific research and writing experiences. In addition, the authors needs to develop themselves to have the sensitivity and insights to the scientific frontiers and development trend of certain discipline or professional field, as well as the corresponding abilities of comprehensive analysis and reviewing.

Partial dampness is the initial stage in the bushing damp process,so the effective diagnosis of partial dampness can avoid the further development of the damp. The partial damp diagnosis method of bushing based on the frequency domain spectroscopy (FDS) is proposed in this paper. Firstly,oil-paper insulation samples with different moisture content are prepared,and partial damped samples are formed through combination. Then the FDS characteristics are obtained. The results show that partial distribution of moisture leads to oil-paper insulation interfaces with different moisture content,and the interface relaxation polarization loss peak is introduced in the FDS curves. The greater the degree of partial dampness in the radial direction,the greater the amplitude of the loss peak,and it moves to the high frequency direction. The effectiveness of the diagnosis of partial dampness of bushing based on the characteristics of the interface relaxation polarization loss peak is verified by the simulation model of the transformer bushing. It shows that a new method for early fault warning and diagnosis of the transformer bushing is provided.

In order to obtain the characteristic parameters of dampness status of resin impregnated paper (RIP),the time domain dielectric response technique is performed on the dampness status evaluation,and the RIP moisture contents are intensively studied based on polarization and depolarization current (PDC) method. Firstly,RIP insulation samples with different moisture contents are prepared in the laboratory and the PDC curves are measured. Then,the optimization algorithm combining genetic algorithm and interior point method is introduced,and the parameters of extended Debye model are obtained by Matlab simulation. Finally,two characteristic parameters of dampness status are extracted,which are the relaxation contribution coefficient of the maximum time constant branch A 9 and the stable depolarization charge quantity Q d-5000. Conclusions from the research results are as follows. The PDC curve moves upward as the moisture content increases. The dampness of the RIP insulation results in the increase of its conductivity and the decrease of its insulation resistance,absorption ratio andpolarization index. The parameters of the 9-branch extended Debye model are sensitive to the RIP insulation dampness status,and the A 9 shows a linear relationship with moisture content. The depolarization charge quantity is sensitive to moisture content,and the Q d-5000 shows an exponential relationship with moisture content.

In order to prolong the shelf life of fresh leaves of Perilla frutescens and ensure the storage quality of leaves during storage and retail, a newly developed coating fresh-keeping paper bag was used to package the leaves of Perilla frutescens in this study. The composite coating solution used in the experiment was prepared by dissolving chitosan, sodium D-isoascorbate, tea polyphenols and calcium chloride in acetic acid aqueous solution in a certain ratio. The effects of different component concentrations in the composite coating solution of fresh-keeping paper bags on the sensory quality, VC content and weight loss rate of Perilla frutescens were investigated by single factor and orthogonal experiments, and the optimal component concentration ratio of the composite coating solution was determined as follows: Chitosan concentration 2.0%, sodium D-isoascorbate concentration 2.4%, tea polyphenols concentration 0.25%, and calcium chloride concentration 0.6%. The physical, chemical and antibacterial properties analysis showed that when the coating amount was 30 g/m2, the composite coating solution had formed uniform coating on the surface of the paper. At this time, the coated paper had strong antibacterial ability, and the coating penetrated into the fiber gap of paper, so that the weight, thickness, elongation and moisture content of paper were improved, the water vapor permeability decreased, and the tensile strength and wettability decreased slightly, which met the packaging requirements of Perilla frutescens leaves and would have broad prospects for development in the field of fruit and vegetable packaging.

BackgroundBy analyzing the publication of scientific and technological papers of the provincial centers for disease control and prevention (CDCs) in China, we can understand their scientific research strength, dominant disciplines, research hotspots, and talent development, which is conducive for further optimizing the scientific research construction of the disease control system.ObjectiveTo conduct a bibliometric analysis and draw a visual map of the Chinese Science Citation Database (CSCD) sourced papers published by 31 provincial CDCs in China from 2011 to 2020, to understand the scientific research status of China's provincial CDC system in the past ten years.MethodsIn April 2021, China National Knowledge Infrastructure was used to retrieve CSCD sourced papers published by 31 provincial CDCs (excluding Taiwan Province, Hong Kong and Macau Special Administrative Regions) in China as the primary unit from 2011 to 2020, and finally 5231 CSCD papers were included. Bibliometric analysis indicators include number of CSCD papers published and financial support rate, proportion of CSCD papers to total Chinese papers, distribution of CSCD papers published in high-volume journals, and number of papers for a specific CDC that their first authors affiliated with. Citespace 5.8.R1 software was used to draw author's cooperation network map, keyword co-occurrence map, keyword clustering information table, and keyword emergence map.ResultsThe number of CSCD papers published every year showed a stationary trend, and the total funding rate was 61%, showing an year-by-year upward trend (increased from 49.3% in 2011 to 68.7% in 2020). Jiangsu Province, Fujian Province, and Beijing CDCs ranked the top three in the total number of CSCD papers contributed by a specific CDC. The Chinese Journal of Epidemiology, Chinese Journal of Public Health, Chinese Journal of Zoonoses, Chinese Journal of Preventive Medicine, and Chinese Journal of Endemic Diseases were the top five high-volume journals. The top three authors of CSCD papers (counted as co-authors) were Xu Bianli of Henan Provincial Center for Disease Control and Prevention (110 papers), Yan Yansheng of Fujian Provincial Center for Disease Control and Prevention (72 papers), and Wang Quanyi of Beijing Center for Disease Prevention and Control (71 papers), and they studied the epidemiology of parasitic diseases and infectious diseases, the prevention and treatment of natural epidemic diseases and AIDS, and the epidemiology of infectious diseases, respectively. The keyword co-occurrence map showed that AIDS, zoonotic diseases, hand-foot-mouth disease, etc. (frequency ≥90) were the key research directions of provincial CDCs in the past ten years. The keyword clustering categories were closely related, although there were subtle differences, the topics focused on virus and chronic disease research. The keyword emergence results suggested that the frontiers of research had gradually shifted from infectious diseases such as enterovirus, hantavirus, and Zika virus to food-borne diseases and chronic non-communicable diseases such as tumors and senile diseases over time.ConclusionThe number of papers issued by the provincial CDCs in China in the past ten years has shown an overall steady and rising trend. The leading themes of researchers and institutions are infectious diseases, parasitic diseases, etc., while food-borne diseases and elderly diseases are the hot frontiers.

In this paper, 1-methylcyclopropene (1-MCP) controlled release packaging paper was prepared by mixing 1-methylcyclopropene with different proportions of ethyl cellulose ether (EC) and polyacrylic acid (PAA) and then coating it on the paper base. The release mechanism was studied. Saimaiti apricot fruits stored at 2 ℃ were treated with 1-MCP controlled release packaging paper. The effects of 1-MCP controllable slow-release packaging paper on respiratory intensity, hardness, titratable acid, soluble solids, peel color and commodity rate of apricot fruit during storage were studied in order to obtain a kind of fresh-keeping paper which could effectively prolong the storage period of apricot fruit. The results showed that under the conditions of 95% RH, 2 ℃ and 80% polyacrylic acid (PAA), the particle collapse of 1-MCP powder made the gas release slowly, and the release mechanism parameter was 0.49, and the release rate increased with PAA content. Controlled release 1-MCP-coated paper could inhibit the arrival of the peak of respiration intensity of apricot fruit, delay the decrease of hardness, titratable acid and soluble solid content, and maintain the color of peel. The results showed that controlled release 1-MCP-coated paper could effectively maintain the quality of apricot fruits stored in low temperature environment, and would provide some reference for the application of controlled release 1-MCP-coated paper to the storage of other fruits and vegetables.

During the forming of aramid paper honeycomb sandwich component of aircraft composites in the autoclave, the structure bears thermo-mechanical coupling case, and it may exist the phenomenon of the honeycomb crack during the forming. The tensile, compressive, shear and thermal properties of aramid paper honeycomb core are obtained by testing. Meanwhile, the numerical simulation of thermo-mechanical sequential coupling of the whole honeycomb sandwich component and the local core area are carried out by combining the finite element analysis method and the inversion method. The results show that the thermal stress during the forming process will not cause the adhesive layer between honeycomb cells to crack, but gas pressure will. The difference value of pressure difference between honeycomb cells required for adhesive layer′s slight destruction and complete destruction is positively related to the initial normal fracture stress of adhesive layer. The pressure difference required for the adhesive layer′s complete destruction is decreased with the increase of the number of loaded cells.

Objective To establish a simple and rapid paper-based extraction method for human papilloma virus (HPV) DNA and to evaluate the method. Methods The plasmid containing HPV type 16 gene fragment was employed as the test subjects, and then 6 different paper materials were compared and selected by ultraviolet spectrophotometry and real-time fluorescence quantitative PCR (qPCR). Then, according to the efficiency of nucleic acid extraction and the optimal binding area, a convenient paper strip was designed. Finally, the designed paper strip was applied to extract HPV DNA from 18 clinical cervical exfoliated cell samples (13 positives and 5 negatives), with its performance being evaluated after comparing with the conventional boiling method. Results The qualitative filter paper with a nucleic acid binding zone of 2 mm×10 mm could successfully extract HPV DNA from clinical cervical exfoliated cells. When this test strip was used for DNA extraction, all the 13 high-risk HPV positives were successfully detected out of the 18 clinical samples, which was consistent with the results of the conventional boiling method. In addition, the extraction time of the test strip was less than 1 min for each sample, with a detection limit of 8×102 copies/mL and relative standard deviation of 1.15%. Conclusion Our paper-based rapid extraction for HPV DNA does not require pipetting, heating and centrifugation, and the eluent can be directly used as the PCR template for amplification, which greatly simplifies the extraction process of HPV DNA from clinical cervical exfoliated cell samples.