Search

Abstract: The tribological properties of rhenium-doped inorganic fullerene-like MoS2 nanoparticles were studied in poly alpha olefin oil, and compared to inorganic fullerene-like (IF) MS2 (M=Mo,W) nanoparticles and 2H-MoS2 platelets. For this purpose a rotational disc tribometer was used. Different regimes in the Stribeck curve, i.e., boundary, mixed and elasto-hydrodynamic lubrication conditions were studied. A precipitous reduction in friction and wear of oil suspensions with nanoparticles were observed for the entire IF samples. However, Re-doped IF exhibited the best results, presumably due to their reduced tribocharging and agglomeration. The various tribological mechanisms of solid state additives are discussed. [Copyright &y& Elsevier]

Experimental and numerical analyses were conducted to explore the influence of DLC/TiAlN-coated die surfaces in sheet-metal forming under dry and oil-lubricated conditions. In this study, ironing and deep-drawing experiments were performed to determine the potential of the DLC/TiAlN coating in the sheet forming of stainless steels under different tribological conditions. The performance and physical properties of the DLC/TiAlN-coated die surface were obtained through load, surface roughness, and wear measurements as well as hardness and microstructure examination. The experimental results indicated that the DLC/TiAlN coating strongly resists galling under dry friction and thin film lubrication conditions that reduces the friction and forming load. The presence of a thin oil film reduces the sliding-originated surface tensile stresses of the DLC/TiAlN coating, improving the wear resistance of the die surface even at high temperatures and high contact pressures. Thermomechanical numerical analysis supported the experimental results, which confirmed that the lubricant discharged the heat generated in the die–workpiece contact region to reduce the friction and forming load. With the DLC/TiAlN coating, the plain mineral oil with no extreme pressure additives can function as effective as chlorinated paraffin oil for protecting the die surface, thus extending the die service life. Image 1 • Ironing and deep drawing tests performed under different tribological conditions. • DLC/TiAlN coating resists galling under dry friction and thin film lubrication. • DLC/TiAlN utilized more environment-friendly oils than chlorinated paraffin oil. • TiAlN interlayer coating enhanced DLC performance. [ABSTRACT FROM AUTHOR]

Extensive wear appears in the case of dry contacts, or when the lubrication of the contacting surfaces is not appropriate. The aim of this research is to improve the mixed elastohydrodynamic lubrication in hypoid gears by the optimization of manufacture parameters for tooth surface processing. A full numerical analysis of the thermal mixed EHL in hypoid gears is applied. The equation system and the numerical procedure are unified for a full coverage of all the lubrication regions including the full film, mixed, and boundary lubrication. In the hydrodynamically lubricated areas the calculation method employed is based on the simultaneous solution of the Reynolds, elasticity, energy, and Laplace's equations. In the asperity contact areas the Reynolds equation is reduced to an expression equivalent to the mathematical description of dry contact problem. The real geometry and kinematics of the gear pair based on the manufacturing procedure is applied, thus the exact geometrical separation of the mating tooth surfaces is included in the oil film shape, and the real velocities of these surfaces are used in the Reynolds and energy equations. The transient nature of gear tooth mesh is included. The oil viscosity variation with respect to pressure and temperature and the density variation with respect to pressure are included. The non-Newtonian behaviour of the lubricant is considered. Using this model, the pressures, film thickness, temperatures, and power losses in the mixed lubrication regime are predicted. By using the developed method, the influence of the manufacturing parameters on the conditions of mixed elastohydrodynamic lubrication is investigated. On the basis of the obtained results recommendations are formulated to improve the mixed EHL and the efficiency of face-milled hypoid gears. • A full numerical analysis of the mixed EHL in hypoid gears is performed. • The influence of the manufacture parameters on mixed EHL in hypoid gears is investigated. • Recommendations are formulated to improve the EHL characteristics of hypoid gears by optimizing the manufacture procedure. [ABSTRACT FROM AUTHOR]