Search

Aluminium and iron chloride were added to a biological nutrient removal pilot plant (1,500 population equivalent) treating urban wastewater to investigate the control of Microthrix parvicella bulking and foaming by metallic salts. Monitoring plant performance over two 6-month periods showed a slight impact on the removal efficiencies. Addition of metallic salts (Me; aluminium or aluminium + iron) at a concentration of 41 mmol Me(kg MLSS·d) (MLSS: mixed liquor suspended solids) over 70 days allowed a stabilization of the diluted sludge volume index (DSVI), whereas higher dosages (94 mmol Me(kg MLSS·d) over 35 days or 137 mmol Me(kg MLSS·d) over 14 days induced a significant improvement of the settling conditions. Microscopic observations showed a compaction of biological aggregates with an embedding of filamentous bacteria into the flocs that is not specific to M. parvicella as bacteria from phylum Chloroflexi are embedded too. The quantitative polymerase chain reaction targeting M. parvicella further indicated a possible growth limitation in addition to the flocculation impact at the high dosages of metallic salts investigated. DSVI appeared to be correlated with the relative abundance of M. parvicella. [ABSTRACT FROM AUTHOR]

Oxygen transfer in biological wastewater treatment processes with high sludge concentration, such as membrane bioreactor (MBR), is an important issue. The variation of a-factor versus mixed liquor suspended solids (MLSS) concentration was investigated in a full scale MBR plant under process conditions, using mass balances. Exhaustive data from the Supervisory Control And Data Acquisition (SCADA) and from additional online sensors (COD, DO, MLSS) were used to calculate the daily oxygen consumption (OC) using a non-steady state mass balance for COD and total N on a 24-h basis. To close the oxygen balance, OC has to match the total oxygen transfer rate (OTRtot) of the system, which is provided by fine bubble (FB) diffusers in the aeration tank and coarse bubbles (CB) in separate membrane tanks. First assessing OTRCB, then closing the balance OC=OTRtot allowed to calculate OTRFB and to fit an exponential relationship between OTRFB and MLSS. A comparison of the a-factor obtained by this balance method and by direct measurements with the off-gas method on the same plant is presented and discussed. [ABSTRACT FROM AUTHOR]

This study aims at synthesizing experiences in the practical application of ASM type models. The information is made easily accessible to model users by creating a database of modelling projects. This database includes answers to a questionnaire that was sent out to model users in 2008 to provide inputs for a Scientific and Technical Report of the IWA Task Group on Good Modelling Practice - Guidelines for use of activated sludge models, and a literature review on published modelling projects. The database is analysed to determine which biokinetic model parameters are usually changed by modellers, in which ranges, and what values are typically used for seven selected activated sludge models. These results should help model users in the calibration step, by providing typical parameter values as a starting point and ranges as a guide. However, the proposed values should be used with great care since they are the result of averaging practical experience and not taking into account specific parameter correlations. [ABSTRACT FROM AUTHOR]

The first objective of this work was to evaluate the ability of the long-term BOD tests to provide the total biodegradable COD (BCOD) for domestic wastewaters. Results show that the method is repeatable (using two different volume samples, 97 and 164 mL) and that the fractions of BCOD determined were not statistically different from the one obtained by respirometry (at low S/X ratio). Respirometric tests were also repeatable. They were shown to be sensitive to the origin of the sludge. The results obtained are in the range of literature data. But they later indicated that long-term bioassays (>20 days) give higher biodegradable fractions than the other methods (BOD and respirometry). The second objective was to compare soluble fractions obtained with raw and pre-flocculated samples. Flocculated filtered COD is significantly lower than filtered COD, even if a pore size of 0.1 mm is used. The comparison to literature values shows that physicochemical RBCOD fractions are significantly higher than the ones obtained using bioassays. Comparison with the fractions used in calibrated models would help the choice of the more suitable method for modelling purposes. [ABSTRACT FROM AUTHOR]

The quality of simulation results can be significantly affected by errors in the published model (typing, inconsistencies, gaps or conceptual errors) and/or in the underlying numerical model description. Seven of the most commonly used activated sludge models have been investigated to point out the typing errors, inconsistencies and gaps in the model publications: ASM1; ASM2d; ASM3; ASM3+ Bio-P; ASM2d+ TUD; New General; UCTPHO+. A systematic approach to verify models by tracking typing errors and inconsistencies in model development and software implementation is proposed. Then, stoichiometry and kinetic rate expressions are checked for each model and the errors found are reported in detail. An attached spreadsheet (see http://www.iwaponline.com/wst/06104/0898.pdf) provides corrected matrices with the calculations of all stoichiometric coefficients for the discussed biokinetic models and gives an example of proper continuity checks. [ABSTRACT FROM AUTHOR]

The Good Modelling Practice Task Group (GMP-TG) of the International Water Association (IWA) is developing guidelines for the use of Activated Sludge Models (ASM). As part of this work the group created and sent out a questionnaire to current and potential activated sludge model users in 2007. The objectives of the questionnaire were (i) to better define the profile of ASM users, (ii) to identify the tools and procedures that are actually used and (iii) to highlight the main limitations while building and using ASM-type models. Ninety-six answers were received from all over the world, from several types of organisation. The results were analysed to identify the modellers' perceptions of models depending on their profile. The results also highlighted the main topics of interest for improving modelling procedures which are standardisation of the available modelling guidelines and better experience and knowledge transfer. [ABSTRACT FROM AUTHOR]

This paper serves as a problem statement of the issues surrounding uncertainty in wastewater treatment modelling. The paper proposes a structure for identifying the sources of uncertainty introduced during each step of an engineering project concerned with model-based design or optimisation of a wastewater treatment system. It briefly references the methods currently used to evaluate prediction accuracy and uncertainty and discusses the relevance of uncertainty evaluations in model applications. The paper aims to raise awareness and initiate a comprehensive discussion among professionals on model prediction accuracy and uncertainty issues. It also aims to identify future research needs. Ultimately the goal of such a discussion would be to generate transparent and objective methods of explicitly evaluating the reliability of model results, before they are implemented in an engineering decision-making context. [ABSTRACT FROM AUTHOR]

The objective of this work was to analyse the impact of different geometric and operating parameters on the alpha factor value for fine bubble aeration systems equipped with EPDM membrane diffusers. Measurements have been performed on nitrifying plants operating under extended aeration and treating mainly domestic wastewater. Measurements performed on 14 nitrifying plants showed that, for domestic wastewater treatment under very low F/M ratios, the alpha factor is comprised between 0.44 and 0.98. A new composite variable (the Equivalent Contact Time, ECT) has been defined and makes it possible for a given aeration tank, knowing the MCRT, the clean water oxygen transfer coefficient and the supplied air flow rate, to predict the alpha factor value. ECT combines the effect on mass transfer of all generally accepted factors affecting oxygen transfer performances (air flow rate, diffuser submergence, horizontal flow). [ABSTRACT FROM AUTHOR]

Investigates the usefulness of measures to evaluate a control strategy for wastewater treatment plants through the Benchmark protocol. Focus on the performance evaluation required to assess a given control strategy using the benchmark protocol; Performance index weighted according to economic relevance; Robustness index of control performance.