Search

Biofiltration has been shown to be effective for disinfection by-product (DBP) precursor control, however few studies have considered its role in the potential formation of DBPs. Biofilm is composed of heterogeneous bacteria as well as extracellular polymeric substances (EPS). The objective of this study was to determine the contribution of biofilm-related materials such as EPS to form nitrogen-containing DBPs upon chloramination, and to determine the influence of cyclical (scheduled on-off) biofilter operation on DBP precursor removal. Biologically active media was sampled from a full-scale biofilter operating under cold-water conditions (3.6 ± 0.5 °C) and extracted using a cation exchange resin into a phosphate buffer solution. Biomass concentrations, as determined using adenosine triphosphate (ATP) measurements, remained stable at 298 ± 55 ng ATP/g media over the trial period. N-nitrosodimethylamine (NDMA) and haloacetonitrile (HAN4) formation potential (FP) tests conducted under uniform formation conditions (UFC) using extracted biofilm yielded 0.80 ± 0.27 ng NDMA/g media and 18.7 ± 3.3 ng dichloroacetonitrile (DCAN)/g media. Further analyses of extracted biofilm using fluorescence spectroscopy and liquid chromatography-organic carbon detection indicated the presence of proteins above 20 kDa and humic-like substances. Extracted proteins (93.5 ± 8.1 μg/g media) correlated well (R = 0.90) with UV 280 measurements, indicating that spectrophotometry may serve as a valuable tool to quantify proteins in extracted biofilms. While substances in biofilms can serve as NDMA and DCAN precursors, the full-scale cyclically-operated biofilter that was examined did not show release of NDMA precursors during start-up following stagnation periods of 6 h or more. These biofilters consistently removed 6.9 ± 4.3 ng/L of NDMA precursors; typical NDMA UFC-FP of biofilter effluent was 8.5 ± 2.6 ng/L.

The objective of this pilot study was to evaluate the impact of cyclical (operated 8–12 h per day) and continuous biofilter operation with respect to biomass development, biological enzyme activity and treated water quality (in terms of organics, nutrients and disinfection by-product (DBP) formation potential). Continuously operated biofilters developed greater densities of biomass, as measured by ATP, when compared to cyclically operated filters; reducing the empty bed contact time (EBCT) increased biomass density under continuous flow conditions. However, once normalized to biomass, it was shown that cyclically operated filters exhibited higher enzyme activity, indicating that this method of operation may improve bacterial function. Reduction of organics was generally similar for both continuous and cyclical filters with the same EBCT, however, cyclical filters demonstrated higher variability during the first 4 h following start-up. Overall, HAA formation potential was better controlled by continuously operated filters, due to poor performance by the cyclical filters upon start-up while THM precursors were removed equally well by all filters. To understand the removal capacity for NDMA precursors through biological filters, both naturally occurring NDMA FP and NDMA FP resulting from spiked anthropogenic precursors was monitored through the filter depth. All the filters removed 90% of the naturally occurring NDMA FP within the first 45 cm; cyclical operation resulted in higher reduction of spiked anthropogenic NDMA precursors (50% higher than continuously operated) demonstrating the advantage of routine shut down on overall microbial activity. Tools to monitor and predict biofilter performance are in high demand. Here we present an “effective activity” term which combines enzyme activity with contact time (EBCT). Effective esterase activity was strongly correlated to DOC reduction as a function of filter operation (cyclical or continuous) and EBCT; effective phosphatase activity was indicative of phosphate removal. The results of this study indicate that routine shut down of the filters as this location improved enzyme activity without compromising control of chlorinated DBPs (THMs and HAAs) or NDMA derived from natural and anthropogenic precursors.

Many water providers monitor adenosine triphosphate (ATP) as an indicator of biological acclimation of their biofilters; however, strong correlations between ATP concentration and filter performance (e.g., organic matter or disinfection by-product precursor removal) are not typically observed. As an alternative, this study evaluated the use of enzyme activity for monitoring biological processes within filters. Recent studies have proposed that enzyme activity may be used as an indicator of biofilter function as it provides a means to quantify biodegradation which may allow for a more accurate measure of degradation potential and to gain a better understanding of biofilter performance. Sampling was completed from full- and pilot-scale biofilters to assess impacts associated with pre-treatments, varying sources waters, as well as pre-treatment and operating conditions. Enzyme activity (carboxylic esterase, phosphatase, s-glucosidase, α-glucosidase, s-xylosidase, chitinase, and cellulase) and ATP were measured from the top 5 cm of biofilter media representative of typical full-scale sampling; water quality parameters included dissolved organic carbon (DOC) and disinfection by-products (DBPs): trihalomethane (THM) formation potential (FP), and haloacetic acid FP (HAA FP). Results confirmed that ATP was not a reliable monitoring tool for DOC and DBP FP reduction in biofilters. A strong relationship was observed between esterase activity and DOC reduction; chitinase activity significantly correlated to THM FP reduction for filters treating three different source waters and HAA FP reduction achieved by filters treating the same source water with a range of pre-treatment and backwash conditions. This study showed that enzyme activity may be appropriate for monitoring biological processes within drinking water filters and may act as a surrogate for the removal of organic compounds.

The use of fluorescence data coupled with neural networks for improved predictability of drinking water disinfection by-products (DBPs) was investigated. Novel application of autoencoders to process high-dimensional fluorescence data was related to common dimensionality reduction techniques of parallel factors analysis (PARAFAC) and principal component analysis (PCA). The proposed method was assessed based on component interpretability as well as for prediction of organic matter reactivity to formation of DBPs. Optimal prediction accuracies on a validation dataset were observed with an autoencoder-neural network approach or by utilizing the full spectrum without pre-processing. Latent representation by an autoencoder appeared to mitigate overfitting when compared to other methods. Although DBP prediction error was minimized by other pre-processing techniques, PARAFAC yielded interpretable components which resemble fluorescence expected from individual organic fluorophores. Through analysis of the network weights, fluorescence regions associated with DBP formation can be identified, representing a potential method to distinguish reactivity between fluorophore groupings. However, distinct results due to the applied dimensionality reduction approaches were observed, dictating a need for considering the role of data pre-processing in the interpretability of the results. In comparison to common organic measures currently used for DBP formation prediction, fluorescence was shown to improve prediction accuracies, with improvements to DBP prediction best realized when appropriate pre-processing and regression techniques were applied. The results of this study show promise for the potential application of neural networks to best utilize fluorescence EEM data for prediction of organic matter reactivity.

Surface waters may contain varying levels of wastewater effluent associated with de facto reuse, which may influence their toxicological properties both prior to and following treatment. This study examined the genotoxic response of three surface waters containing a range of wastewater effluent (5%, 10%, and 25% by volume). The SOS Chromotest™ was used to assay the genotoxicity of both chlorinated and unchlorinated mixtures. Chlorinated mixtures were also analyzed for trihalomethanes (THMs), haloacetonitriles (HANs), and halonitromethanes (HNMs); their concentrations were used to calculate a relative toxicity index for each sample, based on published potencies in the comet assay and subsequently referred to as predicted genotoxicity. Wastewater effluents were observed to be reactive in the genotoxicity assay, whereas raw and chlorinated surface waters were not. Upon chlorination, surface waters containing 5% or 10% wastewater did not elicit a response and only modest effects were observed for higher wastewater ratios (25%). The measured SOS responses correlated well with predicted genotoxicity (R = 0.92) and THM concentrations (R = 0.92). This is important since THMs themselves are non-reactive in either the SOS or comet genotoxic assays, but their formation may serve as surrogates for non-regulated DBPs which drive toxic effects.

N-Nitrosodimethylamine (NDMA) is a disinfection by-product (DBP) with many known precursors such as amine-containing pharmaceuticals that can enter the environment via treated wastewater. Reverse osmosis and tight nanofiltration membranes (MW cutoff200 Da) are treatment technologies that demonstrate high removal of many compounds, but at relatively high energy costs. Looser membranes (200 Da) may provide sufficient removal of a wide range of contaminants with lower energy costs. This study examined the rejection of pharmaceuticals that are known NDMA precursors (∼300 Da) using nanofiltration (MW cutoff ∼350 Da). MQ water was compared to two raw water sources, and results illustrated that NDMA precursors (as estimated by formation potential testing) were effectively rejected in all water matrices (84%). Mixtures of pharmaceuticals vs. single-spiked compounds were found to have no impact on rejection from the membranes used. The use of MQ water vs. surface waters illustrated that natural organic matter, colloids, and inorganic ions present did not significantly impact the rejection of the amine-containing pharmaceuticals. This study illustrates that NDMA formation potential testing can be effectively used for assessing NDMA precursor rejection from more complex samples with multiple and/or unknown NDMA precursors present, such as wastewater matrices.

“Effective Enzyme Activity”, or simply “Effective Activity”, is proposed as a biofiltration monitoring tool which combines enzyme activity with empty bed contact time (EBCT) to quantify biodegradation potential. The primary objective of this study was to evaluate the applicability of the Effective Activity concept for predicting water quality in biofiltration systems. This pilot-scale study evaluated eight different biofilter configurations in order to quantify impacts associated with filter media (anthracite/sand or granular activated carbon), pre-treatment (settled water with or without ozonation) and operating conditions (15- and 30-min EBCT, and backwash with or without chlorine). Microbial characterization included biomass concentration, as measured by adenosine triphosphate (ATP), in addition to esterase and phosphatase activity. Water quality parameters included dissolved organic carbon (DOC), trihalomethane (THM) formation potential (FP), haloacetic acid (HAA) FP, haloacetonitrile (HAN) FP, iodinated DBP FP (THMs and HAAs) and inorganic nutrients (phosphorus and nitrogen). Results confirmed the benefits to treated water quality associated with the application of an ozone residual of 0.5 mg/L, utilization of GAC filter media, eliminating chlorinated backwash, and extending EBCT. This study demonstrated a good relationship between effective esterase activity and reductions in DOC and THM FP, including those systems which incorporate pre-ozonation. As such, this study showed that Effective Activity may be appropriate for relating biomass characterization to treated water quality and highlights the importance of quantifying biomass activity in addition to quantity.

Previous studies have reported that biofilm extracted from full-scale biofilters can serve as nitrogenous disinfection by-product (N-DBP) precursors. Detached biofilm materials could escape during filter ripening and form N-DBP upon chloramination. This study examined the potential breakthrough of biofilm and N-DBP precursors during filter ripening at two water treatment plants (WTPs). The presence of biofilm material in aqueous samples was estimated by total adenosine triphosphate (tATP) levels; N-DBP formation potential (FP) tests were conducted under uniform formation conditions to quantify N-nitrosodimethylamine (NDMA) and haloacetonitrile (HAN4) precursors. While tATP peaks in filter effluent were observed post backwash at both WTPs, temporary increases of effluent NDMA FP were only observed during filter ripening where particle-associated NDMA precursors served as the dominant contributor. Overall, biofilters examined in this study demonstrated a consistent removal of NDMA FP regardless of the filter ripening process.

To provide information for the design and improvement of full-scale biofilters, pilot-scale biofiltration studies are the current industry standard because they utilize the same filter media size and loading rate as the full-scale biofilters. In the current study, bench-scale biofilters were designed according to a biofilter scaling model from the literature, and the ability of the bench-scale biofilters to accurately represent the organics removal of pilot-scale biofilters was tested. To ensure similarity in effluent water quality between bench- and pilot- or full-scale biofilters at the same influent substrate concentration, the tested model requires that either mass transport resistance or biofilm shear loss takes primacy over the other. The potential primacy of mass transport resistance or biofilm shear loss was evaluated via water quality testing (dissolved organic carbon, specific ultraviolet absorbance, liquid chromatography – organic carbon detection, trihalomethane formation potential, and haloacetic acid formation potential). The biofilters also were characterized for adenosine triphosphate (ATP) content, enzyme activity, extracellular polymeric substances, and microbial community structure. The results of this study indicate that biofilm shear loss takes primacy over mass transport resistance for bench-scale biofilter design in this system; thus, bench-scale biofilters designed in this manner accurately represent organics removal in pilot-scale biofilters. Applying this scaling procedure can reduce filter media requirements from many kilograms to just a few grams and daily water requirements from thousands of liters to less than 10 L. This scaling procedure will allow future researchers to test alternative treatment designs and operating conditions without the need for expensive pilot-scale studies.

Legacy lead and copper components are ubiquitous in plumbing of large buildings including schools that serve children most vulnerable to lead exposure. Lead and copper samples must be collected after varying stagnation times and interpreted in reference to different thresholds. A total of 130 outlets (fountains, bathroom and kitchen taps) were sampled for dissolved and particulate lead as well as copper. Sampling was conducted at 8 schools and 3 institutional (non-residential) buildings served by municipal water of varying corrosivity, with and without corrosion control (CC), and without a lead service line. Samples included first draw following overnight stagnation (8h), partial (30 s) and fully (5 min) flushed, and first draw after 30 min of stagnation. Total lead concentrations in first draw samples after overnight stagnation varied widely from 0.07 to 19.9 μg Pb/L (median: 1.7 μg Pb/L) for large buildings served with non-corrosive water. Higher concentrations were observed in schools with corrosive water without CC (0.9-201 μg Pb/L, median: 14.3 μg Pb/L), while levels in schools with CC ranged from 0.2 to 45.1 μg Pb/L (median: 2.1 μg Pb/L). Partial flushing (30 s) and full flushing (5 min) reduced concentrations by 88% and 92% respectively for corrosive waters without CC. Lead concentrations were10 μg Pb/L in all samples following 5 min of flushing. However, after only 30 min of stagnation, first draw concentrations increased back to45% than values in 1st draw samples collected after overnight stagnation. Concentrations of particulate Pb varied widely (≥0.02-846 μg Pb/L) and was found to be the cause of very high total Pb concentrations in the 2% of samples exceeding 50 μg Pb/L. Pb levels across outlets within the same building varied widely (up to 1000X) especially in corrosive water (0.85-851 μg Pb/L after 30MS) confirming the need to sample at each outlet to identify high risk taps. Based on the much higher concentrations observed in first draw samples, even after a short stagnation, the first 250mL should be discarded unless no sources of lead are present. Results question the cost-benefit of daily or weekly flushing as a remediation strategy. As such, current regulatory requirements may fail to protect children as they may not identify problematic taps and effective mitigation measures.

Disinfection by-products (DBPs) are formed when naturally occurring organic matter reacts with chlorine used in drinking water treatment, and DBPs formed in chlorinated drinking water samples have been shown to cause a genotoxic response. The objective of the current study was to further understand the principles of biofiltration and the resulting impacts on the formation of DBPs and genotoxicity. Pilot-scale systems were utilized to assess the performance of engineered biofilters enhanced with hydrogen peroxide, in-line coagulants, and nutrients when compared to passively operated biofilters and conventional treatment (coagulation, flocculation, sedimentation, non-biological filtration). Organic fractionation was completed using liquid chromatography-organic carbon detection (LC-OCD). Water samples were chlorinated after collection and examined for the removal of trihalomethane (THM), haloacetic acid (HAA), and adsorbable organic halide (AOX) precursors. Additionally, the formation potential of two halogenated furanones, 3-chloro-4(dichloromethyl)-2(5H)-furanone (MX) and mucochloric acid (MCA), and genotoxicity was determined. Biofiltration was shown to preferentially remove more DBP precursors than dissolved organic carbon (DOC). Formation potential of the unregulated DBPs, including MX and MCA, and genotoxic response was shown to be correlated to THM formation. These results infer that monitoring for THMs and HAAs provide insight to the formation of more mutagenic DBPs such as halogenated furanones, and that biofiltration may preferentially remove precursors to DBPs at a rate exceeding the removal of DOC.

Natural organic matter (NOM) in drinking water can react with disinfectants to form disinfection by-products (DBPs). Halogenated furanones are a group of emerging DBPs that can account for 20–60% of the total mutagenicity observed in drinking water. This study examined the impacts of bench-scale coagulation and subsequent chlorination on DBP formation as well as genotoxicity using three source waters located in Ontario, Canada. Two halogenated furanones 3-chloro-4-(dichloromethyl)-2(5H)-furanone (MX) and mucochloric acid (MCA) were analyzed; along with trihalomethanes (THMs), haloacetic acids (HAAs), and absorbable organic halides (AOX). NOM was quantified using liquid chromatography–organic carbon detection (LC–OCD). Measured MX and MCA formation was 6.9–15.3 ng/L and 43.2–315 ng/L following optimized coagulation and subsequent chlorination of the three waters tested. DBP formation and speciation were evaluated as a function of the specific NOM fractions present in the source waters. Humics, building blocks, and biopolymers were highly correlated with DBP formation. Correlations between DBPs were also investigated and a potential relationship between MCA and/or MX vs. HAAs was observed. MX was the only measured DBP that contributed to genotoxicity, representing less than 0.001% of AOX by mass but responsible for 40–67% of the genotoxic response in chlorinated Ottawa River water samples. Genotoxic potential decreased with alum dosages, signifying that coagulation was effective at removing genotoxic DBP precursors.

Fluorescence spectroscopy was used as a characterization method to examine organic fouling of single ultrafiltration (UF) fibres at bench-scale. Low doses of coagulant were applied to modify organic properties, without significant formation of precipitates. This approach compliments previous studies investigating coagulation as a pre-treatment method for UF fouling control, which have principally focused on reduction of foulant concentrations. Using a continuous system, short time-scale fluorescence results demonstrated significant adsorption of humic components to virgin membrane fibres. Following an initial adsorption phase, protein-like material was the only organic component to be significantly removed by UF. Low doses of coagulant (

Media type is a critical design consideration when implementing biofiltration for drinking water treatment. Granular activated carbon (GAC) has been shown to provide superior performance when compared to a wide range of media types, largely due to its higher surface area. Engineered ceramic media is an attractive alternative to GAC as it has a similar surface area but at a lower cost. This pilot-scale biofiltration study compared the performance of GAC, anthracite and two different effective sizes of ceramic (CER) media (1.0 mm and 1.2 mm), in terms of dissolved organic carbon (DOC), head loss, turbidity, and disinfection by-product formation potential (DBPFP). Biological acclimation was monitored using adenosine tri-phosphate (ATP) measurements; biomass was further examined using laccase and esterase enzyme activity assays. When compared to other media types examined, biological GAC had higher (p > 0.05) removals of DOC (9.8 ± 3.8%), trihalomethane formation potential (THMFP, 26.3 ± 10.2%), and haloacetic acid formation potential (HAAFP, 27.2 ± 14.0%). CER media required 6–7 months to biologically acclimate, while filters containing GAC and anthracite were biologically active (>100 ng of ATP/g media) following 30–45 days of operation. Once acclimated, ATP values of 243 and 208 ng/g attained for CER 1.0 and 1.2, respectively, were statistically comparable to GAC (244 ng/g) and higher than anthracite (110 ng/g), however this did not translate into greater organics removal. Esterase and laccase enzyme kinetics were highest for GAC, while CER was shown to have greater biodegradation potential than anthracite. The four media types attained similar turbidity reduction (p > 0.05), however ceramic media filters were observed to have run times which were 1.5–2.3 times longer when compared to anthracite, which could represent potential cost savings in terms of energy for pumping and backwash requirements. Overall, ceramic media was shown to be a potential alternative to anthracite when considering biofiltration, especially during cold water conditions (T

Halo-benzoquinones (HBQs) have been previously detected as disinfection by-products in chlorinated drinking water. The current work investigates the link between natural organic matter (NOM) characteristics and HBQ formation during bench-scale coagulation of raw water. Three source waters (Lake Ontario, Otonabee River and Grand River) were subjected to jar testing using alum followed by chlorination. NOM fractions were analyzed via liquid chromatography-organic carbon detection (LC-OCD), while HBQs were quantified using liquid chromatography-triple quadrupole mass spectrometry. One HBQ, 2,6-dichloro-(1,4)benzoquinone (2,6-DCBQ), was identified in all waters after chlorination, and appeared to decrease with increased applied alum dose. 2,6-DCBQ exhibited high correlations with some humic NOM indicators: humic substance concentration (in Grand and Otonabee River waters only), UV absorbance at 254 nm, UV absorbance at 254 nm of the humic peak, and specific UV absorbance of humics (humic SUVA). With data pooled from the three waters, the biopolymer fraction of NOM was most strongly correlated with 2,6-DCBQ formation (R(2) = 0.78, p < 0.001); this may be due to co-removal of biopolymers with HBQ precursors during coagulation. These results indicate that coagulation processes can be effective for reduction, but not elimination, of HBQ precursors.

The impact of natural organic matter (NOM) and cations on the rejection of five endocrine disrupting compounds (EDCs) and pharmaceutically active compounds (PhACs) (acetaminophen, carbamazepine, estrone, gemfibrozil, oxybenzone) by nanofiltration (NF) was examined. The water matrices included membrane bioreactor (MBR) effluent, Lake Ontario water and laboratory-prepared waters modelled to represent the characteristics of the Lake Ontario water. The impact of cations in natural waters on compound rejection was also examined by doubling the natural cation concentration (calcium, magnesium, sodium) in both the Lake Ontario water and the MBR effluent. The presence of Suwannee River NOM spiked into laboratory-grade water was found to cause an increase in compound NF rejection. In addition, the presence of cations alone in laboratory-grade water did not have a significant impact on rejection with the exception of the polar compound gemfibrozil. However, when cation concentration in natural waters was increased, a significant decrease in the rejection of EDCs and PhACs was observed. This suggests that the presence of cations may result in a reduction in the association of EDCs and PhACs with NOM.

The overall objective of this study was to investigate the impact of blending membrane-treated water treatment plant (WTP) residuals with plant-filtered water on finished water quality in terms of biostability and disinfectant by-product (DBP) formation. Filter backwash water (FBWW) was treated with a pilot-scale ultrafiltration (UF) membrane to produce permeate that was blended with plant-finished water. The batch studies involved storing samples for a specified time with a disinfectant residual to simulate residence time in the distribution system. Both chlorinated and non-chlorinated FBWW streams were evaluated, and the experimental design incorporated free chlorine, monochloramine, and chlorine dioxide in parallel to a model system that did not receive a disinfectant dose. The results of the study found that blending 10% UF-treated FBWW with plant-filtered water did not have an impact on water biostability as monitored with heterotrophic plate counts (HPCs) or DBP concentrations as monitored by TTHM and HAA5 concentrations. However, the presence of preformed THM and HAA species found in chlorinated FBWW streams may result in higher levels of initial DBP concentrations in blended water matrices, and could have a significant impact on finished water quality in terms of meeting specific DBP guidelines or regulations.

Lead results from 78,971 water samples collected in four Canadian provinces from elementary schools, daycares, and other large buildings using regulatory and investigative sampling protocols were analyzed to provide lead concentration distributions. Maximum concentrations reached 13,200 and 3890 μg/L following long and short stagnation periods respectively. High lead levels were persistent in some large buildings, reflected by high median values considering all taps, or specific to a few taps in the building. Simulations using the Integrated Uptake Biokinetic (IEUBK) model and lead concentrations after 30 min of stagnation in the dataset showed that, for most buildings, exposure to lead at the tap does not increase children's blood lead levels (BLLs). However, buildings or taps with extreme concentrations represent a significant health risk to young children attending school or daycare, as the estimated BLL far exceeded the 5 μg/dL threshold. Ingestion of water from specific taps could lead to acute exposure. Finally, for a few taps, the total daily lead intake reached the former World Health Organization (WHO) tolerable level for adults, suggesting potential health risks.

Ammonia can be used to minimize bromate concentrations by blocking two of three potential bromate formation pathways. It was theorized that (bi)carbonate alkalinity in the presence of ammonia would inhibit bromate formation since the pathway that ammonia does not block requires hydroxyl radicals (OH ), and (bi)carbonate alkalinity is an OH scavenger. Experiments where (bi)carbonate alkalinity was increased from 50 to 119 mg/L (as CaCO 3 ) in the presence of excess ammonia resulted in up to 50% reduction in bromate formation, providing evidence in support of the theory. While OH is scavenged by (bi)carbonate alkalinity, it is promoted by hydrogen peroxide (H 2 O 2 ). When ozone reacts with natural organic matter the H 2 O 2 that is formed may therefore render ammonia less effective. Experiments conducted in this study demonstrated this principle.

Chlorine dioxide (ClO2) inactivation of Bacillus subtilis ATCC 19659 spores was examined at pilot-scale during periods representative of winter and summer temperature extremes at the Britannia Water Treatment Plant in Ottawa, Canada. In addition, bench-scale experiments using the same source water (Ottawa River, Ontario, Canada), as well as buffered and unbuffered laboratory waters were conducted using B. subtilis spores. Bench-scale inactivation of B. subtilis spores by ClO2 was similar to reported values for Cryptosporidium parvum (both organisms being more resistant to ClO2 than Giardia lamblia), suggesting the possibility that these spores may be used as potential indicators for protozoan parasites. Additionally, spore inactivation was observed to be influenced by pH in laboratory (distilled deionised water) water but not in Ottawa River water. At pilot-scale, spore inactivation was influenced by water temperature: a ClO2 dose of 2.5 mg/L resulted in a spore inactivation of approximately 2.0 log10 and 0.5 log10 at water temperatures of 23.2d egrees C and 5.2 degrees C, respectively. Chlorite concentrations remained below both the US EPA maximum contaminant level of 1.0 mg/L and the maximum contaminant level goal of 0.8 mg/L for up to 2.0log10 B. subtilis inactivation.

Factorial experiments were conducted using source waters from seven drinking water treatment plants in Ontario, Canada to develop statistically based model equations capable of predicting chlorine dioxide consumption and chlorite and chlorate formation upon chlorine dioxide application. The equations address raw water quality and operational parameters including pH, temperature, chlorine dioxide concentration, reaction time and water organic content (as described by non-purgeable organic carbon x ultraviolet absorbance measured at 254 nm, NPOC x UV254). Terms describing two-factor interaction effects were also included, improving the accuracy of the predictive equations in fitting measured response concentrations as evaluated through internal and external validations. Nearly 80% of the predictions for chlorine dioxide consumption and chlorite formation were observed to be within 20% of the measured levels. Over 90% of the predicted chlorate levels were within +/- 0.1 mg/L of the measured levels. Chlorine dioxide concentration and NPOC x UV254 were key parameters when developing the predictive models.

This bench-scale study investigated the passage of particle-associated bacteriophage through a dual-media (anthracite-sand) filter over a complete filter cycle and the effect on subsequent ultraviolet (UV) disinfection. Two model viruses, bacteriophages MS2 and T4, were considered. The water matrix was de-chlorinated tap water with either kaolin or Aldrich ® humic acid (AHA) added and coagulated with alum to form floc before filtration. The turbidity of the influent flocculated water was 6.4 ± 1.5 NTU . Influent and filter effluent turbidity and particle counts were measured as well as headloss across the filter media. Filter effluent samples were collected for phage enumeration during three filter cycle stages: (i) filter ripening; (ii) stable operation; and (iii) end of filter cycle. Stable filter operation was defined according to a filter effluent turbidity goal of 0.3 NTU . Influent and filter effluent samples were subsequently exposed to UV light (254 nm) at 40 mJ / cm 2 using a low pressure UV collimated beam. The study found statistically significant differences ( α = 0.05 ) in the quantity of particle-associated phage present in the filter effluent during the three stages of filtration. There was reduced UV disinfection efficiency due to the presence of particle-associated phage in the filter effluent in trials with bacteriophage MS2 and humic acid floc. Unfiltered influent water samples also resulted in reduced UV inactivation of phage relative to particle-free control conditions for both phages. Trends in filter effluent turbidity corresponded with breakthrough of particle-associated phage in the filter effluent. The results therefore suggest that maintenance of optimum filtration conditions upstream of UV disinfection is a critical barrier to particle-associated viruses.

This study investigated whether colloid-sized particles can enmesh and protect viruses from 254-nm ultraviolet (UV) light and sought to determine the particle characteristics (e.g. size, chemical composition) that are most relevant in causing a protective effect. Two viral surrogates (MS2 coliphage and bacteriophage T4), three types of particles (kaolin clay, humic acid powder, and activated sludge), two coagulants (alum and ferric chloride), two filtration conditions (none and 0.45 microm), and two UV doses (40 and 80 mJ/cm2 for MS2 coliphage; 2 and 7 mJ/cm2 for bacteriophage T4) were considered in a series of bench-scale UV collimated beam experiments. Transmission electron microscopy was used to qualitatively confirm the phage particle-association after coagulation. Humic acid and activated sludge floc particles shielded both viral surrogates to a statistically significant degree (with99% confidence) relative to particle-free control conditions, while the kaolin clay particles provided no significant protection. The results of the study suggest that particles2 microm in diameter are large enough to protect viruses from UV light and that particulate chemical composition (e.g. UV-absorbing organic content) may be a critical factor in the survival of particle-associated viruses during UV disinfection.

A membrane bioreactor and reverse osmosis (MBR-RO) system was developed to assess potential reuse applications of municipal wastewater. The objective of the study was to examine the water quality throughout the system with a focus on waterborne pathogens, disinfection by-products (DBPs) and nitrate. This paper will discuss the presence of these contaminants in MBR effluent and focus on their subsequent removal by RO. This study has shown that high quality reuse water can be produced from municipal wastewater through the use of an MBR-RO system. The water meets California Title 22 reuse regulations for non-potable applications and US EPA drinking water limits for trihalomethanes (THM) (80 microg/L), haloacetic acids (HAA) (60 microg/L), chlorite (1.0 mg/L), total coliform (not detectable), viruses (not detectable), and nitrate/nitrite (10 mg N/L). However, THM formation (182-689 microg/L) attributed to cleaning of the MBR with chlorine and incomplete removal by subsequent RO treatment resulted in reuse water with THM levels (40.2+/-19.9 microg/L) high enough to present a potential concern when considering drinking water applications. Nitrate levels of up to 3.6 mg N/L, which resulted from incomplete removal by the RO membrane, are also a potential concern. A denitrification step in the MBR should be considered in potable water applications.

The drinking water industry is closely examining options to maintain disinfection in distribution systems. In particular this research compared the relative efficiency of the chlorite ion (ClO2-) to chlorine dioxide (ClO2) for biofilm control. Chlorite levels were selected for monitoring since they are typically observed in the distribution system as a by-product whenever chlorine dioxide is applied for primary or secondary disinfection. Previous research has reported the chlorite ion to be effective in mitigating nitrification in distribution systems. Annular reactors (ARs) containing polycarbonate and cast iron coupons were used to simulate water quality conditions in a distribution system. Following a 4 week acclimation period, individual ARs operated in parallel were dosed with high (0.25mg/l) and low (0.1mg/l) chlorite concentrations and with high (0.5 mg/l) and low (0.25mg/l) chlorine dioxide concentrations, as measured in the effluent of the AR. Another set of ARs that contained cast iron and polycarbonate coupons served as controls and did not receive any disinfection. The data presented herein show that the presence of chlorite at low concentration levels was not effective at reducing heterotrophic bacteria. Log reductions of attached heterotrophic bacteria for low and high chlorite ranged between 0.20 and 0.34. Chlorine dioxide had greater log reductions for attached heterotrophic bacteria ranging from 0.52 to 1.36 at the higher dose. The greatest log reduction in suspended heterotrophic bacteria was for high dose of ClO2 on either cast iron or polycarbonate coupons (1.77 and 1.55). These data indicate that it would be necessary to maintain a chlorine dioxide residual concentration in distribution systems for control of microbiological regrowth.

Ammonia can inhibit the formation of bromate in ozonated drinking water by reacting with free bromine (HOBr/OBr-), an intermediate in bromate formation, to form bromamines. Bromamines do not participate in bromate formation, however, they will decay due to autonomous decomposition and through reaction with ozone and hydroxyl radicals. The reaction with ozone controls the overall decay rate. This reaction also results in a net loss of ammonia from the system, leading to the possibility that all ammonia may be oxidized before the ozone residual in the water is eliminated, allowing bromate formation to resume. This paper presents a review of our understanding of bromamine chemistry and identifies areas that are not adequately understood, which may prevent an accurate estimation of ammonia's impact on bromate formation.