Search

This paper describes a completely non-contact ultrasonic method of gas flow metering using air-coupled leaky Lamb waves. To show proof of principle, a simplified representation of gas flow in a duct, comprising two separated thin isotropic plates with a gas flowing between them, has been modelled and investigated experimentally. An airborne compression wave emitted from an air-coupled capacitive ultrasonic transducer excited a leaky Lamb wave in the first plate in a non-contact manner. The leakage of this Lamb wave crossed the gas flow at an angle between the two plates as a compression wave, and excited a leaky Lamb wave in the second plate. An air-coupled capacitive ultrasonic transducer on the opposite side of this second plate then detected the airborne compression wave leakage from the second Lamb wave. As the gas flow shifted the wave field between the two plates, the point of Lamb wave excitation in the second plate was displaced in proportion to the gas flow rate. Two such measurements, in opposite directions, formed a completely non-contact contra-propagating Lamb wave flow meter, allowing measurement of the flow velocity between the plates. A COMSOL Multiphysics® model was used to visualize the wave fields, and accurately predicted the time differences that were then measured experimentally. Experiments using different Lamb wave frequencies and plate materials were also similarly verified. This entirely non-contact airborne approach to Lamb wave flow metering could be applied in place of clamp-on techniques in thin-walled ducts or pipes. [ABSTRACT FROM AUTHOR]

Since the identification of micro-cracks in engineering materials is very valuable in understanding the initial and slight changes in mechanical properties of materials under complex working environments, numerical simulations on the propagation of the low frequency S 0 Lamb wave in thin plates with randomly distributed micro-cracks were performed to study the behavior of nonlinear Lamb waves. The results showed that while the influence of the randomly distributed micro-cracks on the phase velocity of the low frequency S 0 fundamental waves could be neglected, significant ultrasonic nonlinear effects caused by the randomly distributed micro-cracks was discovered, which mainly presented as a second harmonic generation. By using a Monte Carlo simulation method, we found that the acoustic nonlinear parameter increased linearly with the micro-crack density and the size of micro-crack zone, and it was also related to the excitation frequency and friction coefficient of the micro-crack surfaces. In addition, it was found that the nonlinear effect of waves reflected by the micro-cracks was more noticeable than that of the transmitted waves. This study theoretically reveals that the low frequency S 0 mode of Lamb waves can be used as the fundamental waves to quantitatively identify micro-cracks in thin plates. [ABSTRACT FROM AUTHOR]

The transmission behavior of Lamb waves and the possible occurrence of resonance at an adhesive butt joint of plates are studied experimentally. To this purpose, two 2.5-mm thick aluminum alloy plates are bonded at their edges using cyanoacrylate-based adhesive. Bonded plate specimens with different joint conditions are prepared by changing the bonding procedure. The measurements are performed for the transmission characteristics of the lowest-order symmetric (S0) and antisymmetric (A0) Lamb modes for the frequency range of 0.4–0.6 MHz below the cut-off frequency of the higher-order modes. The experimental results show that the transmission coefficients of the S0 and A0 modes exhibit different frequency-dependent characteristics depending on the joint condition. Furthermore, for the incidence of the S0 mode at the center frequency of 1 MHz, the transmitted S0 mode in weakly bonded specimens shows a long oscillation tail due to the resonance effect. The experimental results are discussed in the light of the theoretical results based on the spring-type interface model. The interfacial stiffnesses identified from the transmission coefficients are shown to be correlated with the bonding condition of the joint and give reasonable estimates of the resonance frequencies of weakly bonded specimens. [ABSTRACT FROM AUTHOR]

Antisymmetric and symmetric Lamb-type feature guided waves (FGW) have recently been shown to exist in small angle plate bends. This paper reports Semi-Analytical Finite Element (SAFE) method simulations revealing the existence of a new family of Shear Horizontal ( SH B ) type of FGW mode in 90° bends in plate structures. Mode shapes and velocity dispersion curves are extracted, demonstrating the SH -like nature of a bend-confined mode identified in studies of power flow across the bend. The SH B mode is shown to have reduced attenuation in the higher frequency range, making it an ideal choice for high-resolution inspection of such bends. Further modal studies examine the physical basis for mode confinement, and argue that this is strongly related to FGW phenomena reported earlier, and also linked to the curvature at the bend region. Wedge acoustic waves discussed widely in literature are shown as arising from surface-limiting of the SH B mode at higher frequencies. The results are validated by experiments and supported by 3D Finite Element (FE) simulations. [ABSTRACT FROM AUTHOR]

Air-coupled ultrasonic inspection using leaky Lamb waves offers attractive possibilities for non-contact testing of plate materials and structures. A common method uses an air-coupled pitch–catch configuration, which comprises a transmitter and a receiver positioned at oblique angles to a thin plate. It is well known that the angle of incidence of the ultrasonic bulk wave in the air can be used to preferentially generate specific Lamb wave modes in the plate in a non-contact manner, depending on the plate dimensions and material properties. Multiple reflections of the ultrasonic waves in the air gap between the transmitter and the plate can produce additional delayed waves entering the plate at angles of incidence that are different to those of the original bulk wave source. Similarly, multiple reflections of the leaky Lamb waves in the air gap between the plate and an inclined receiver may then have different angles of incidence and propagation delays when arriving at the receiver and hence the signal analysis may become complex, potentially leading to confusion in the identification of the wave modes. To obtain a better understanding of the generation, propagation and detection of leaky Lamb waves and the effects of reflected waves within the air gaps, a multiphysics model using finite element methods was established. This model facilitated the visualisation of the propagation of the reflected waves between the transducers and the plate, the subsequent generation of additional Lamb wave signals within the plate itself, their leakage into the adjacent air, and the reflections of the leaky waves in the air gap between the plate and receiver. Multiple simulations were performed to evaluate the propagation and reflection of signals produced at different transducer incidence angles. Experimental measurements in air were in good agreement with simulation, which verified that the multiphysics model can provide a convenient and accurate way to interpret the signals in air-coupled ultrasonic inspection using leaky Lamb waves. [ABSTRACT FROM AUTHOR]

In the presented work, the characterization of plates using zero group velocity Lamb modes is discussed. First, analytical expressions are shown for the determination of the k – ω location of the zero group velocity Lamb modes as a function of the Poisson’s ratio. The analytical expressions are solved numerically and an inverse problem is formulated to determine the unknown wave velocities in plates of known thickness. The analysis is applied to determine the elastic properties of tungsten and aluminum plates based on the experimentally measured frequency spectra. [ABSTRACT FROM AUTHOR]

We previously formulated a semi-analytical finite element technique for Lamb waves in a plate surrounded by fluids and investigated the dispersion curves and wave structures for leaky Lamb waves. Herein, this technique is extended to the calculation of transient responses both in a plate and in fluids for dynamic loading on the plate surface. To gain fundamental insights into guided wave inspection for a water-filled pipe or tank, guided waves generated upon transient loading of a flat plate water-loaded on one side were analyzed. The results show that a quasi-Scholte mode propagating at the plate-water interface is useful for the long-range inspection of a water-loaded plate because of its non-attenuation and minimal dispersion; moreover, this mode has superior generation efficiency in the low-frequency range, while it is localized near the plate-water interface at higher frequencies. [ABSTRACT FROM AUTHOR]

Recent improvements in tomographic reconstruction techniques generated a renewed interest in short-range ultrasonic guided wave inspection for real-time monitoring of internal corrosion and erosion in pipes and other plate-like structures. Emerging evidence suggests that in most cases the fundamental asymmetric A0 mode holds a distinct advantage over the earlier market leader fundamental symmetric S0 mode. Most existing A0 mode inspections operate at relatively low inspection frequencies where the mode is highly dispersive therefore very sensitive to variations in wall thickness. This paper examines the potential advantages of increasing the inspection frequency to the so-called constant group velocity (CGV) point where the group velocity remains essentially constant over a wide range of wall thickness variation, but the phase velocity is still dispersive enough to allow accurate wall thickness assessment from phase angle measurements. This paper shows that in the CGV region the crucial issue of temperature correction becomes especially simple, which is particularly beneficial when higher-order helical modes are also exploited for tomography. One disadvantage of working at such relatively high inspection frequency is that, as the slower A0 mode becomes faster and less dispersive, the competing faster S0 mode becomes slower and more dispersive. At higher inspection frequencies these modes cannot be separated any longer based on their vibration polarization only, which is mostly tangential for the S0 mode while mostly normal for the A0 at low frequencies, as the two modes become more similar as the frequency increases. Therefore, we propose a novel method for suppressing the unwanted S0 mode based on the Poisson effect of the material by optimizing the angle of inclination of the equivalent transduction force of the Electromagnetic Acoustic Transducers (EMATs) used for generation and detection purposes. [ABSTRACT FROM AUTHOR]

Highlights: [•] Mode conversion of Lamb waves can be used to size notch-type defects in plates. [•] Spectral leakage can hide small amplitude modes in the frequency–wavenumber domain. [•] Baseline subtraction technique is applied to 2DFFT to detect low amplitude modes. [•] Lower limits of detection method are tested via the FEM. [Copyright &y& Elsevier]

Highlights: [•] Our aim is to analyze the mode transmission in the notched plate within the relatively short propagation distance. [•] The originally-transmitted modes and newly-converted modes were separated. [•] The velocities and energy of converted modes were extracted to locate and evaluate the notches, respectively. [ABSTRACT FROM AUTHOR]

Abstract: In this paper, the group velocities of the zero order antisymmetric (A0) Lamb modes in a phononic crystal plate with single layer cylindrical holes parallel to the surface of the plate were investigated theoretically. The results show that by increasing the filling fraction, the A0 mode can be efficiently slowed down and the group velocity of the A0 modes can be tuned from the positive to the negative referring to the phase velocity. Moreover, the zero group velocity of the A0 modes can be obtained with a given filling fraction. These results may be useful in designing acoustic devices. [Copyright &y& Elsevier]

Abstract: Numerical simulations were carried out to quantify the reflection and transmission characteristics of the fundamental Lamb modes propagating in aluminium sub-plates, which are formed due to a semi-infinite horizontal crack. It was observed that, a Lamb mode propagating in a sub-plate when incident at the edge of a crack, undergoes reflection and transmits through the main plate, as well as the other sub-plate. The mode transmitted through the sub-plate has been termed the ‘Turning Lamb Mode’ (TLM). Furthermore, a mode converted mode also propagates along with the TLM. This mode has been termed the ‘Mode Converted Turning Lamb Mode’ (MCTLM). Reflection and transmission characteristics of the fundamental Lamb modes in aluminium sub-plates were studied at frequencies 150kHz, 175kHz, and 200kHz. Experiments conducted to validate the observations made in numerical simulations, confirmed that the transmission and reflection characteristics depend on the thickness ratio. From this study it is surmised that when a Lamb mode propagates through a plate containing horizontal crack, the TLM and the MCTLM start propagating from one sub-plate to the other at the rear edge of the crack and amplitude of these modes depends on the location of the crack across the plate thickness. [Copyright &y& Elsevier]

Abstract: The reflection of obliquely incident symmetric and anti-symmetric Lamb wave modes at the edge of a plate is studied. Both in-plane and Shear-Horizontal (SH) reflected wave modes are spawned by an obliquely incident in-plane Lamb wave mode. Energy reflection coefficients are calculated for the reflected wave modes as a function of frequency and angle of incidence. This is done by using the method of orthogonal mode decomposition and by enforcing traction free conditions at the plate edge using the method of collocation. A PZT sensor network, affixed to an Aluminum plate, is used to experimentally verify the predictions of the analysis. Experimental results provide support for the analytically determined results. [Copyright &y& Elsevier]

Abstract: Defect imaging using scanning laser source technique has been investigated for a plate with rounded defects and notch-type defects in our previous studies. This paper examines frequency dependence of the defect images with both calculations and experiments in order to acquire clearer images. Both calculation and experimental results for a straight notch revealed that clearer images of notch-type defects can be obtained in the range of low frequency-thickness product below about 200kHzmm. Moreover, images of the defects of various shapes were obtained by synthesizing images from eight receiving transducers, and similarly to the case of the straight notches, they became more clearly in the low frequency range. [Copyright &y& Elsevier]

Abstract: We have implemented three-dimensional (3D) elastodynamic finite integration technique (EFIT) simulations to model Lamb wave scattering for two flaw-types in an aircraft-grade aluminum plate, a rounded rectangle flat-bottom hole and a disbond of the same shape. The plate thickness and flaws explored in this work include frequency–thickness regions where several Lamb wave modes exist and sometimes overlap in phase and/or group velocity. For the case of the flat-bottom hole the depth was incrementally increased to explore progressive changes in multiple-mode Lamb wave scattering due to the damage. The flat-bottom hole simulation results have been compared to experimental data and are shown to provide key insight for this well-defined experimental case by explaining unexpected results in experimental waveforms. For the rounded rectangle disbond flaw, which would be difficult to implement experimentally, we found that Lamb wave behavior differed significantly from the flat-bottom hole flaw. Most of the literature in this field is restricted to low frequency–thickness regions due to difficulties in interpreting data when multiple modes exist. We found that benchmarked 3D EFIT simulations can yield an understanding of scattering behavior for these higher frequency–thickness regions and in cases that would be difficult to set up experimentally. Additionally, our results show that 2D simulations would not have been sufficient for modeling the complicated scattering that occurred. [Copyright &y& Elsevier]

Abstract: An analysis is given to the band structure of the two-dimensional phononic crystal plate constituted of a square array of elastic anisotropic, circular Pb cylinders embedded in elastic isotropic epoxy. The numerical results show that the band gap can be tuned by rotating the anisotropic material orientation. It is found that the influence of anisotropy on band gap of Lamb wave is clearly different from that on the band gap of bulk waves. The thickness of the system under study is a sensitive parameter to affect the influence of anisotropic materials on the normalized gap width. [Copyright &y& Elsevier]

Abstract: A model for quantifying the performance of acoustic emission (AE) systems on plate-like structures is presented. Employing a linear transfer function approach the model is applicable to both isotropic and anisotropic materials. The model requires several inputs including source waveforms, phase velocity and attenuation. It is recognised that these variables may not be readily available, thus efficient measurement techniques are presented for obtaining phase velocity and attenuation in a form that can be exploited directly in the model. Inspired by previously documented methods, the application of these techniques is examined and some important implications for propagation characterisation in plates are discussed. Example measurements are made on isotropic and anisotropic plates and, where possible, comparisons with numerical solutions are made. By inputting experimentally obtained data into the model, quantitative system metrics are examined for different threshold values and sensor locations. By producing plots describing areas of hit success and source location error, the ability to measure the performance of different AE system configurations is demonstrated. This quantitative approach will help to place AE testing on a more solid foundation, underpinning its use in industrial AE applications. [Copyright &y& Elsevier]

Abstract: The aim of this work is to study the fundamental Lamb modes interaction with defects in isotropic plates. For these experimental investigations, symmetrical notches with various depths milled in aluminum plates are considered. Moreover, the incident Lamb wave of a specific mode is generated by means of two identical thin piezoceramic transducers placed at the opposite sides of the plate. The waves scattered by the notch are recorded with conventional transducers located on the plate surface in front and behind the defect. The selection of the A 0 or the S 0 modes is obtained by exciting the transducers with anti-phased or in-phased signals, respectively. Furthermore, a calibration process is investigated to correct errors caused by the presence of the receiver between the emitters and the defects. The power reflection and transmission coefficients are then obtained and the power balance is verified. Finally, these measurements are compared successfully with those obtained by a numerical method using the finite-element modeling described in a previous work. [Copyright &y& Elsevier]

The evolution of the experimental frequency width of symmetric modes of an aluminum plate is studied as a function of the angle of incidence below the first critical angle. It is found that the frequency width predicted by resonant scattering theory, corrected for the directivity of emitter and receiver, generally explains the experimental frequency width well. However, large discrepancies remain for the frequency width of the S1 mode at angles of incidence larger than 9°. It is demonstrated that these are caused by not taking into account the complex nature of the slowness of the plate mode. This suggests that there is a need for a theory that models the interaction of a beam of ultrasound, bounded in space and time, with an elastic plate. [Copyright &y& Elsevier]

Abstract: A novel combined spectral estimate (CSE) method for differentiation and estimation the phase velocities of multimode Lamb waves whose wave numbers are much close or overlap one another in multiplayer plates is presented in this paper, which based on auto-regressive (AR) model and 2-D FFT. Simulated signals in brass plate were processed by 2-D FFT and CSE. And experiments are performed by using two conventional angle probes as emitter and receiver on the same surface of three-layered aluminum/xpoxy/aluminum plates, which include symmetrical and unsymmetrical plates. The multimode Lamb waves are excited in these laminates, and the received signal is processed by 2-D FFT and CSE, respectively. The results showed that the phase velocities of multimode signals whose wave numbers are much closed cannot be differentiated by 2-D FFT, but CSE has strong spatial resolution. Compared the measured phase velocities with the theoretical values, the error is smaller than 2% on the whole. It promises to be a useful method in experimental signals processing of multimode Lamb waves. [Copyright &y& Elsevier]