Search

Antisymmetric and symmetric Lamb-type feature guided waves (FGW) have recently been shown to exist in small angle plate bends. This paper reports Semi-Analytical Finite Element (SAFE) method simulations revealing the existence of a new family of Shear Horizontal ( SH B ) type of FGW mode in 90° bends in plate structures. Mode shapes and velocity dispersion curves are extracted, demonstrating the SH -like nature of a bend-confined mode identified in studies of power flow across the bend. The SH B mode is shown to have reduced attenuation in the higher frequency range, making it an ideal choice for high-resolution inspection of such bends. Further modal studies examine the physical basis for mode confinement, and argue that this is strongly related to FGW phenomena reported earlier, and also linked to the curvature at the bend region. Wedge acoustic waves discussed widely in literature are shown as arising from surface-limiting of the SH B mode at higher frequencies. The results are validated by experiments and supported by 3D Finite Element (FE) simulations. [ABSTRACT FROM AUTHOR]

Air-coupled ultrasonic inspection using leaky Lamb waves offers attractive possibilities for non-contact testing of plate materials and structures. A common method uses an air-coupled pitch–catch configuration, which comprises a transmitter and a receiver positioned at oblique angles to a thin plate. It is well known that the angle of incidence of the ultrasonic bulk wave in the air can be used to preferentially generate specific Lamb wave modes in the plate in a non-contact manner, depending on the plate dimensions and material properties. Multiple reflections of the ultrasonic waves in the air gap between the transmitter and the plate can produce additional delayed waves entering the plate at angles of incidence that are different to those of the original bulk wave source. Similarly, multiple reflections of the leaky Lamb waves in the air gap between the plate and an inclined receiver may then have different angles of incidence and propagation delays when arriving at the receiver and hence the signal analysis may become complex, potentially leading to confusion in the identification of the wave modes. To obtain a better understanding of the generation, propagation and detection of leaky Lamb waves and the effects of reflected waves within the air gaps, a multiphysics model using finite element methods was established. This model facilitated the visualisation of the propagation of the reflected waves between the transducers and the plate, the subsequent generation of additional Lamb wave signals within the plate itself, their leakage into the adjacent air, and the reflections of the leaky waves in the air gap between the plate and receiver. Multiple simulations were performed to evaluate the propagation and reflection of signals produced at different transducer incidence angles. Experimental measurements in air were in good agreement with simulation, which verified that the multiphysics model can provide a convenient and accurate way to interpret the signals in air-coupled ultrasonic inspection using leaky Lamb waves. [ABSTRACT FROM AUTHOR]

We previously formulated a semi-analytical finite element technique for Lamb waves in a plate surrounded by fluids and investigated the dispersion curves and wave structures for leaky Lamb waves. Herein, this technique is extended to the calculation of transient responses both in a plate and in fluids for dynamic loading on the plate surface. To gain fundamental insights into guided wave inspection for a water-filled pipe or tank, guided waves generated upon transient loading of a flat plate water-loaded on one side were analyzed. The results show that a quasi-Scholte mode propagating at the plate-water interface is useful for the long-range inspection of a water-loaded plate because of its non-attenuation and minimal dispersion; moreover, this mode has superior generation efficiency in the low-frequency range, while it is localized near the plate-water interface at higher frequencies. [ABSTRACT FROM AUTHOR]

Highlights: [•] Mode conversion of Lamb waves can be used to size notch-type defects in plates. [•] Spectral leakage can hide small amplitude modes in the frequency–wavenumber domain. [•] Baseline subtraction technique is applied to 2DFFT to detect low amplitude modes. [•] Lower limits of detection method are tested via the FEM. [Copyright &y& Elsevier]

Abstract: The aim of this work is to study the fundamental Lamb modes interaction with defects in isotropic plates. For these experimental investigations, symmetrical notches with various depths milled in aluminum plates are considered. Moreover, the incident Lamb wave of a specific mode is generated by means of two identical thin piezoceramic transducers placed at the opposite sides of the plate. The waves scattered by the notch are recorded with conventional transducers located on the plate surface in front and behind the defect. The selection of the A 0 or the S 0 modes is obtained by exciting the transducers with anti-phased or in-phased signals, respectively. Furthermore, a calibration process is investigated to correct errors caused by the presence of the receiver between the emitters and the defects. The power reflection and transmission coefficients are then obtained and the power balance is verified. Finally, these measurements are compared successfully with those obtained by a numerical method using the finite-element modeling described in a previous work. [Copyright &y& Elsevier]