Search

Abstract: This paper investigated the bending strength of girth-welded stainless steel circular hollow sections by numerical method. At first, finite element simulation of girth welding process was carried out to obtain the weld-induced residual stresses and deformations employing sequentially coupled three-dimensional thermo-mechanical finite element formulation. Then, nonlinear finite element analysis in which the moment versus end-rotation response, the ultimate moment resistance and the failure mode of the girth-welded circular hollow sections under pure bending were explored incorporating the residual stresses and depressions along with the initial global geometric imperfections was performed. Feasibility of adopting the current codified provisions (Eurocode 3) for stainless steel circular hollow sections in bending as the cross-section slenderness limit for girth-welded stainless steel circular hollow section flexural members was also examined. Results showed that the flexural behavior of girth-welded stainless steel circular hollow sections always involves local buckling near the girth weld on the compression side, which significantly affects the moment versus end-rotation behavior. Moreover, the results demonstrated that the Class 3 slenderness limit of 280 from Eurocode 3 for stainless steel circular hollow sections in flexure may be applied to girth-welded stainless steel circular hollow sections subjected to bending. [Copyright &y& Elsevier]

This work presents an investigation on the compressive strain capacity of resisting buckling on an X80 steel corroded pipeline subjected to a bending moment using nonlinear finite element analysis (FEA) validated by full-scale tests. The modelling results indicate that the existing strain-based assessment method is not suitable for pipelines with deep corrosion and has certain application limitations. Consequently, a new evaluation method based on far-field strain was developed to predict the buckling failure of corroded pipelines subjected to bending loads. The influence of the corrosion shape type, corrosion size (i.e., depth d , length L , and width w), pipe geometry, and internal pressure on the critical buckling strain capacity and critical buckling moment of the pipeline were studied using parameter sensitivity analysis to verify the proposed strain criteria. The results illustrate that the variation trends between the critical buckling strain and the critical buckling moment with each factor were consistent, indicating that the proposed novel strain-based evaluation method is effective and applicable. In addition, the buckling resistance of a pipeline with rectangular corrosion is relatively weaker than that with a semi-spherical corrosion pit or cylindrical grooved corrosion under the same defect size. Further, the critical compressive strain capacity of a corroded pipeline is primarily affected by the depth and width of the corrosion, whereas the effect of the corrosion length is relatively insignificant. Moreover, the critical length and width of the corrosion defect affecting the bending capacity of resisting buckling were determined as L / D t = 20 and w / π D = 0. 5 , respectively. • A novel strain-based assessment method of local buckling of corroded pipelines. • Determined the effect of defect geometry on critical compressive strain capacity. • Determined the critical defect size that affect the pipe buckling strain capacity. [ABSTRACT FROM AUTHOR]

Abstract: The problem of buckling of the Euler–Bernoulli and Timoshenko beams is analyzed by the finite element method. Significant improvement in accuracy of the method is obtained by replacing the discontinuous function of the bending moment related to the approximation of the eigenfunction obtained by FEM by a “smoothed” function in the Rayleigh quotient. The smoothed function is obtained by fitting the discontinuous one using the least square technique. [Copyright &y& Elsevier]

The current slenderness limits are significantly different in international design codes for cold-formed Circular Hollow Sections (CHS) under pure bending. This paper aims to use the Finite Element (FE) method to understand the behaviour of cold-formed CHS under pure bending and to propose new design rules. The model is calibrated by comparing its predicted load-deflection curves with previously published experimental data. In total, 21 specimens were modelled with diameter-to-thickness ratios ranging from 13 to 122. The current slenderness limits in the present international steel specifications were examined using the FE model and their suitability for cold-formed CHS is discussed. The effect of section slenderness on rotation capacity has been examined where the predicted variation of rotation capacity against section slenderness has been compared to the experimental results. A new equation for the amount of initial geometrical imperfection as a function of section slenderness has been developed and proposed for design purposes. The ovalisation deformation ratio and the critical strain at local buckling were determined and compared for compact, non-compact and slender sections. The progressive bending deformations of CHS at 10 critical steps have been presented and compared for the three cross sectional types, in particular at the maximum moment and bending rotation. In general, a good agreement has been obtained between the predicted strengths and ductilities using the current FE models and those of the experimental data of cold-formed CHS. • Using finite element method to determine the slenderness limit of cold-formed steel tubes and compared to the previous experimental results. • The effect of geometrical imperfections on the deformation cold-formed CHS has been examined. • The rotation capacity has been presented for CHS. • The ovalisation of compact, non-compact and slender section has been analysed. • The buckling mechanism has been analysed by using strain analysis, the critical strain at maximum moment has been determined and compared to the theoretical results. [ABSTRACT FROM AUTHOR]