Search

Metallic wire mesh has gained attention as a potential material for lightweight aircraft structures, e.g., a metallic frame of morphing wings, due to its customizable mechanical properties associated with cell structures. However, the relationship between the pattern design of cell structures and the mechanical characteristics of metallic wire mesh remains unclear. The present work aims to investigate the mechanical behavior of asymmetric crosslinked metallic wire mesh with a hybrid Poisson's ratio pattern, which has the potentials of arbitrary Poisson's ratios. Two typical designs of cell arrangement for asymmetric crosslinked metallic wire mesh were proposed, namely negative Poisson's ratio cells (NPRC) and positive Poisson's ratio cells (PPRC). The in-plane Poisson's ratio of asymmetric crosslinked metallic wire mesh was calculated based on the Euler beam theory. The effects of hybrid Poisson's pattern and interwoven joint on mechanical properties, including macroscopic Poisson's ratio and elastic bending recovery, were analyzed using numerical and experimental methods. The results demonstrate that the analytical Poisson's ratio obtained from the proposed theoretical model agrees well with the simulation result. The hybrid structure which consisted of NPRC and PPRC could effectively control transverse shrinkage and become one of the most efficient potentials for promising structures with the arbitrary Poisson's ratio phenomenon. [ABSTRACT FROM AUTHOR]

Driven by the need for impact resistance and vibration reduction for mechanical devices in extreme environments, an all-metal vibration isolator with 6-degree-of-freedom (6-DOF) motion that is horizontally symmetrical was developed. Its stiffness and damping ability are provided by oblique springs in symmetrical arrangement and a metal–rubber elasto-porous damper. The spring is symmetrically distributed in the center axis of the support load surface. It is necessary to investigate the kinematics and the singularity before conducting multi-body dynamics analysis of the vibration isolator. Based on the theory of dual quaternions, the forward kinematics equations of the isolator were successively derived for theoretical kinematics modeling. In addition, an enhanced Broyden numerical iterative algorithm was developed and applied to the numerical solution of the forward kinematics equations of the vibration isolator. Compared with the traditional rotation-matrix method and Newton–Raphson method, the computational efficiency of the enhanced Broyden numerical iterative algorithm was increased by 680% and 290%, respectively. This was due to the enhanced algorithm without the calculations of any inverse matrix and forward kinematics equations. Finally, according to the forward kinematics Jacobian matrix, the position-singularity trajectory at a given orientation and the orientation-singularity space at a given position are calculated, which provides a basis for the algorithm of the 6-DOF vibration isolator to avoid singular positions and orientations. [ABSTRACT FROM AUTHOR]

In this study, the creep properties of cylindrical metal rubber (MR) specimen under static compression at elevated temperatures were investigated by a series of creep experiments. The cylindrical MR specimen has a good symmetrical property, and the mechanical properties are consistent in its different axial section. The failure determination parameters of MR under the coupling of thermal and mechanical static load of the forming direction were proposed in four aspects: the overall height, the average stiffness, the energy dissipation, and the variation of the loss factor. The variation patterns of the properties of the MR specimens were investigated with a static load at different temperatures for 324 h. The analytical equipment, including the simultaneous thermal analyzer (TGA/DSC), X-ray diffractometer (XRD), and scanning electron microscope (SEM), were used for material characterization and failure analysis. Based on the results, it is found that there are significant differences in the MR property variations subjected to creep tests at different elevated temperatures. The results indicated that an appropriate heat treatment for MR specimens would improve the creep resistance at elevated temperatures. In addition, the overall height and energy dissipation of the MR specimens were increased, and the average stiffness and the loss factor were decreased under the creep tests at 200 °C and 250 °C. However, under the creep tests at 25 °C, 300 °C, 350 °C, and 400 °C, the overall height, the energy dissipation and the loss factor were decreased, but the average stiffness was increased. [ABSTRACT FROM AUTHOR]

In this paper, superelastic (SE) NiTi wire is used to fabricate axially symmetric wire mesh dampers (WMDs) with the expectation of a higher damping capacity. However, the phase transformation damping of the NiTi WMD could be suppressed by the cold-work-induced dislocation. Therefore, the NiTi WMDs were heat-treated and then tested by a hydraulic universal testing machine. The NiTi WMD is found to achieve higher damping capacity when heat-treated at 200 °C. However, the WMD heat-treated at 250 °C suffers from a sharp decline in the loss factor in exchange for an improvement in the stiffness. The sine sweep test was then conducted to examine the dependency of the WMD's vibration isolation performance upon the heat treatment temperature and the excitation acceleration. The NiTi WMD outperforms the 304 stainless steel (SS 304) WMD in damping capacity only when the excitation acceleration magnitude is less than 1.5 g. The stiffness of NiTi WMD can be improved without significantly compromising its damping capacity by heat treatment at 200 °C for 30 min. The present work carries out comprehensive measurements of the NiTi WMD's response to dynamic mechanical test and sine sweep test and addresses how heat treatment influences the stiffness and damping capacity of the SE NiTi WMD. [ABSTRACT FROM AUTHOR]

A horizontally symmetric all-metallic vibration isolator (AM-VI) is proposed to further investigate the dynamic mechanical performance. The novel AM-VI was constructed by combining hat-shaped metal rubber and oblique springs, which were connected in parallel. The springs were arranged symmetrically relative to the support. The elliptic method and the frequency sweeping method were used to compare the dynamic stiffness and the loss factor of the AM-VI. The results demonstrated that the dynamic stiffness and the loss factor calculated by two distinct test methodologies were considerably different, indicating that the inertial force effect of the dynamic testing equipment should be taken into count when adopting the elliptic method. Furthermore, when the vibration isolation performance was evaluated by utilizing mechanical impedance and force transmissibility, the AM-VI achieved excellent vibration isolation performance within a broad frequency range. [ABSTRACT FROM AUTHOR]

The wave propagation and vibration transmission in metamaterial-based elastic rods with periodically attached multi-degree-of-freedom (MDOF) dynamic anti-resonant vibration isolator (DAVI) resonators are investigated. A methodology based on a combination of the transfer matrix (TM) method and the Bloch theorem is developed, yielding an explicit formulation for the complex band structure calculation. The bandgap behavior of the periodic structure arrayed with single-degree-of-freedom (SDOF) DAVI resonators and two-degree-of-freedom (2DOF) DAVI resonators are investigated, respectively. A comparative study indicates that the structure consisting of SDOF DAVI resonators periodically jointed on the metamaterial-based elastic rod can obtain an initial locally resonant band gap 500 Hz smaller than the one given in the published literature. The periodic structure containing 2DOF DAVI resonators has an advantage over the periodic structure with SDOF DAVI resonators in achieving two resonance band gaps. By analyzing the equivalent dynamic mass of a DAVI resonator, the underlying mechanism of achieving a lower initial locally resonant band gap by this periodic structure is revealed. The parameters of the 2DOF DAVI resonator are optimized to obtain the lowest band gap of the periodic structure. The numerical results show that, with the optimal 2DOF DAVI parameters, the periodic structure can generate a much lower initial locally resonant band gap compared with the case before the optimization. [ABSTRACT FROM AUTHOR]

Particular attention has been given to the complexity of the elastic-porous sandwich structure with entangled metallic wire mesh (EMWM), which is a novel rigid-flexible heterogeneous and symmetrical material. The orthogonal experiment design for vacuum brazing was adopted for sensitivity analysis of the key fabrication process on the performances of an EMWM sandwich structure. The shear behaviors of the sandwich structures with different vacuum brazing parameters (e.g., heating rate, brazing temperature, and holding time) were analyzed by mechanical experiments and an interfacial microstructure. The results indicated that the failure behavior of the sandwich structure could be divided into four stages in the mode-I experiment. In addition, the joint quality of the different vacuum brazing process could be shown by the mode-II experiment, and the failure behaviors involves three stages. Additionally, the failure behaviors of the sandwich structure were mainly associated with the deformation of the EMWM core and the strength of the brazing joint. In addition, the relationship between the joint strength and the shear performance of the sandwich structure was revealed through the interfacial microstructure. Furthermore, the importance of the optimized vacuum brazing parameters to fabricate the novel sandwich structure with the best joint performance was demonstrated in this work. [ABSTRACT FROM AUTHOR]

This paper aims to investigate the nonlinear dynamic properties of a two-point and symmetrically supported pipeline bracket system coated with the damping element using an elastic-porous metal rubber. The dynamic model of the studied two-point and symmetric pipeline system was established based on impulse response matrix for accurate and reliable description on its nonlinear behaviours, e.g., energy dissipation and loss factor. The experimental verification of the developed model was performed by means of dynamic test as well as the analyses of nonlinear damping characteristics. The experimental results show a good agreement with the prediction results obtained from the proposed dynamic model. This work provides an alternative method to investigate the dynamics of pipeline vibration system equipped with a damping structure. [ABSTRACT FROM AUTHOR]