Search

The main aim of the EU H2020 project EcoSwing was to demonstrate a technical readiness level of 6–7 for high-temperature superconducting (HTS) technology operating in a wind generator. To reach this goal, a full-scale synchronous HTS generator was successfully designed, built and field-tested in a 3.6 MW turbine. The generator has a rotor with 40 superconducting coils of 1.4 m long. The required >20 km of coated conductor was produced within the project’s time schedule. All coils were tested prior to assembly, with >90% of them behaving as expected. The technical readiness level of HTS coils was thus increased to level 7. Simultaneously, the maturing of cryogenic cooling technology over the last decade was illustrated by the several Gifford-McMahon cold-heads that were installed on-board the rotor and connected with the stationary compressors through a rotating coupling. The cryogenic system outperformed design expectations, enabling stable coil temperatures far below the design temperature of 30 K after only 14 d of cool-down. After ground-based testing at the IWES facility in Bremerhaven, Germany, the generator was installed on an existing turbine in Thyborøn, Denmark. Here, the generator reached the target power range and produced power for over 650 h of grid operation.

In the frame of the EuCARD2 collaboration, aimed at developing the technology for 20 T class accelerator magnets, several demonstrator dipole magnets are being built using high critical current density and fully transposed ReBCO tape-based Roebel-type cables. In accelerator magnets the dynamic magnetic field quality is one of the key parameters, which is affected by the effective inter-strand resistances in the cables. For this reason, measurements of the inter-strand resistances on ReBCO Roebel cables were carried out at 4.2 and 77 K. Acquiring these data is also essential for input of cable simulation models. The cable samples are impregnated with epoxy resin to reduce the effect of transverse stress degradation due to Lorentz forces acting on the strands in the Roebel cables. The measured inter-strand resistance is used to estimate the AC coupling loss in different magnetic field orientations. Moreover, the contributions of diverse interface contact resistances to overall inter-strand resistance of Roebel cables were determined using a novel theoretical model. For validation, the AC loss of cables were examined in various orientations of applied field at 4.2 K. With three analytical models the hysteresis loss was calculated and compared to the measured data. The average inter-strand resistance of the cable samples impregnated with the unfilled epoxy CTD-101K range from 3 to 16 μΩ at 77 K and 1.5 to 9 μΩ at 4.2 K. Between the tapes the copper to copper interface resistance dominates the inter-strand resistance of impregnated Roebel cables. The calculated and measured AC loss for the CTD-101K impregnated Roebel cable lead to equivalent conclusions that the coupling loss is lower than the hysteresis loss within the range of the experiment. These observations substantially differ from earlier results extracted from a similar cable but impregnated with the alumina-filled epoxy resin CTD-101G, which showed considerable coupling loss when exposed to magnetic field parallel the wide face of the cable.

Many high-temperature superconductor (HTS) applications require superconducting cables with high currents while operating in an alternating magnetic field. HTS cables should be composed of numerous superconducting tapes to achieve the required current capacity. Alternating current and magnetic fields cause AC losses in such cables and can provoke conductor instability. AC losses and contact resistances were measured of several cable designs based on commercially available REBCO tapes at the University of Twente. The AC loss was measured under identical conditions for eight REBCO conductors manufactured according to three types of cabling methods—CORC® (Conductor on Round Core), Roebel, and stacked tape, including a full-size REBCO CICC (cable in conduit conductor). The measurements were done at T = 4.2 K without transport current in a sinusoidal AC magnetic field of 0.4 T amplitude and frequencies from 5 to 55 mHz. The AC loss was measured simultaneously by calibrated gas flow calorimeter utilizing the helium boil-off method and by the magnetization method using pick-up coils. Also, the AC loss of two CORC® conductors and a Roebel cable was measured at 77 K. Each conductor was measured with and without background field of 1 T. The measured AC coupling loss in the CORC® and Roebel conductors is negligible at 4.2 K for the applied conditions while at 77 K coupling loss was observed for all conductors. The absence of coupling loss at 4.2 K can be explained by shielding of the conductor interior; this is confirmed with measurement and calculation of the penetration field of CORC® and Roebel cables. The inter-tape contact resistance was measured for CORC® and stacked tape samples at 4.2 and 77 K. It was demonstrated that a short heat treatment of CORC® conductor with solder-coated tapes activates tape-to-tape soldering and decreases the contact resistance. The reduction of contact resistance by two orders in magnitude to tens of nΩm is comparable with the interstrand contact resistance in ITER Nb3Sn type conductors.

The effect of disorder on the normal state resistivity and the superconducting properties of Nb3Sn Sn is explored in a combination of ab initio calculations and microscopic theory. The crystal symmetry is calculated to be preferentially tetragonal at a normal state resistivity below 27.0 ±1.4 μcm, and preferentially cubic above this value, which is shown to be consistent with the experimentally observed transition point. The phonon density of states, the Eliashberg spectrum a2 (w)F (w), the electronphonon coupling constant, the characteristic frequency, the critical temperature Tc, and the upper critical magnetic field at 0 K Hc2 (0) are calculated over a large normal state resistivity range and shown to be consistent with experimental observations. The high degree of consistency between the calculation results and experimental observations is a strong indication that the calculation approach utilized here, a combination of ab initio calculations and microscopic theory, is a useful tool for understanding the superconducting and normal state properties of Nb3Sn.

International audience; A European consortium has progressed towards elementary and assembled conductors viable for AC applications in the project ACropolis. The main goal was to achieve low AC losses and high critical current densities in tapes developed for AC coils, transformers and cables. In order to verify the performance of tapes an extensive characterization programme was carried out. The dependence of critical current and AC losses on the parameters of the tape manufacturing process were scrutinized. Furthermore, SEM-EDX and DTA/TG analyses were performed to study the material microstructure, and the diffusion coefficient of oxygen through different matrix metals was measured. The homogeneity of the tapes was verified with magnetic knife and Hall sensor experiments. Transport current measurements were performed at different mechanical stress conditions and also the distribution of critical current along long tapes was determined with a quasi-continuous four-point measurement. The results confirmed that the low AC loss conductors can be produced on an industrial scale and they are competitive in power engineering applications.