Search

Along with the classical finite element method (FEM), other calculation methods for assessing crack resistance characteristics are currently being actively developed. This is due to the existing shortcomings of the FEM caused by the dependence of the calculation results on the density of the finite element mesh. One of the promising methods being developed in world practice is the extended finite element method (XFEM), which allows obtaining satisfactory calculation results while simplifying the crack modeling procedure and saving calculation time. In this paper, three problems are numerically modeled using the classical FEM and XFEM methods: calculation of a disc crack in a cube under uniaxial tension, calculation of the off-center tension of a compact CT specimen, and calculation of a cylindrical part of an NPP reactor vessel with a semi-elliptical crack under thermal shock. The obtained results showed that the extended finite element method gives sufficiently accurate results compared to analytical solutions and the classical FEM. At the same time, using the XFEM method does not require considering the singularity of stresses at the crack tip when building an FE model. Therefore, the minimum size of the FE can be increased by almost five times while maintaining the accuracy of the results. This greatly simplifies the procedure for constructing the FE mesh, reduces the total number of FEs in the model, and saves computational time. Thus, the XFEM method can be used to calculate the crack resistance characteristics and improve the efficiency of assessing the resistance to brittle fracture of structural elements. [ABSTRACT FROM AUTHOR]

The paper deals with the 3D printing process that is compatible with electrodynamic processing (EDP) of the printed layer in order to increase the density of the latter. Based on mathematical modeling, the influence of the impactor shape for EDP on the stress-strain state of the AMg6 aluminum alloy layer was studied. The formation of residual compressive stresses in the EDP zone was taken as a compaction criterion. The distribution of values along the thickness of the plate of the main parameters and components of the stress-strain state, in particular, the plastic deformation and stress zone dimensions, the depth and width of the contact interaction zone in the metal layer interacting with an impactor roller moving normal to the layer at speeds of 1, 5, and 10 m/s, was determined. The cylindrical impactor with a rounded end surface usage instead a straight quadrangular prism with a rounded side surface formed a higher-density layer, characterized by generation of compressive stresses up to the yield strength of the AMg6 alloy. This helps optimize the structure of the printed metal and increase its durability by forming compressive stress fields in the electrodynamic compaction zone. [ABSTRACT FROM AUTHOR]

The paper deals with the dynamics of asymmetric three-layer hemispherical shells with the discretely symmetric lightweight, rib-reinforced filler under pulsed loads. Since the distances between the ribs are much larger than the dimensions of the rib cross-sections, the theory of independent static and kinematic hypotheses for each layer is applied. In asymmetric shells, the load-bearing layers are made of different materials and have various thicknesses. The equations of motion of asymmetric three-layer spherical shells and natural boundary conditions are obtained using the Hamilton– Ostrogradsky variational principle for the Timoshenko-type shell and rod theory model. This makes it possible to develop an adequate finite element model for asymmetric three-layer shells composed of several materials and obtain numerical results on the dynamic behavior of an asymmetric three-layer elastic structure using the finite element method. The influence of physical and mechanical parameters of asymmetric layers of hemispherical shells on the stress-strain state under axisymmetric internal pulse loading is investigated. New mechanical effects are revealed. [ABSTRACT FROM AUTHOR]

In order to predict the temperature, humidity and deformation of the 3D gel-printing metal laminated green body during the drying process. This paper presents a mathematical model of solving the coupled temperature, moisture, and stress-strain fields during the drying process. This model was established on the Luikov's irreversible thermodynamics and material mechanics. It was numerically solved based on the discrete difference method, and it was implemented into numerical simulations through a combination of sequence and direct coupling method. The results have shown that, for the temperature field, green body temperature field approached to be steady in a short time during drying. For the moisture field, moisture migration exhibited between materials with different initial moisture contents. While for the stress-strain fields, obvious tensile stress state was experienced on the edges of green body longitudinal sides. The research carried out in this paper contributes to provide a comprehensive guide of the process planning of drying process of green body. [ABSTRACT FROM AUTHOR]

Recently, much attention has been given to developing numerical modeling methods for calculations of complex nodes of structural elements, especially for the equipment of the first circuit of NPP. The use of new methods increases the accuracy of the results and significantly reduces the calculation time. This is especially important when solving the problems of modeling the processes of crack nucleation and propagation in the material, in which, in particular, local thickening of the finite element mesh is necessary. In this paper, a description of the "submodeling" technique is given, which allows one to calculate individual components of structural elements, taking into account complex geometric shapes, contact conditions, and other factors that are difficult to take into account in calculations by conventional methods. The submodeling technique was used to calculate the stressstrain state in complex components of the pressure compensator of the WWER-440 reactor unit. For this purpose, a global simplified finite element model of the pressure compensator and a detailed submodel of the injection nozzle were built, taking into account the gap between the containment and the inner surface of the nozzle, as well as contact conditions. The results showed that the submodeling technique gives more conservative results when modeling complex assemblies. Hence, its application increases the reliability of the results obtained when assessing the strength of critical structural elements, particularly the equipment of the first circuit of NPP. [ABSTRACT FROM AUTHOR]

The paper presents a methodology for determining the complete strain diagrams of materials in a complex stress state using the criteria of equivalence, which take into account the different behavior of the material under tension and compression. The proposed methodology is based on determining the relationship between the stress and strain surfaces. Since it is difficult to describe the deformation surface due to the volumetric influence of deformations, it is proposed to introduce the concept of "nominal strain." In this case, the general relationship between the stress and the nominal strain, for the case of a complex stress state, is defined as the relationship between the Euclidean norms of the stress and nominal strain tensors. The obtained dependences show the relations between the real values of stress and nominal strain, preserve the dynamics of change in the secant modulus, and, accordingly, allow comparison with other dependences obtained for a different stress state. The definition of the loading surface, as some geometric figure, is based on the fulfillment of differential conditions that are imposed on this surface and the possibility of determining a sufficient number of points for its construction. In this work, it is proposed to consider the loading surface in the form of a circular paraboloid. Under active loading, this surface expands to its limits – the fracture surface. To determine the characteristics of the above-mentioned surfaces and the law of their expansion, it is sufficient to conduct two basic experiments – for compression and for tension. The work provides a general methodology for determining the internal constants of the equation that describe the selected loading and nominal strain surfaces. [ABSTRACT FROM AUTHOR]

The paper presents the results of experimental studies of the possibility to assess the damage process of steels of different classes by using the LM-hardness method under cyclic loading at different cycle characteristics (stress amplitude, mean stress, loading frequency). Fatigue damage of metal under cyclic loading has been assessed by the method outlined in the PNAE standard. It is shown that the discrepancy between the recommended tabulated values and experimentally obtained values of mechanical characteristics of the material has a significant influence on the character of the calculated fatigue curve of the material, which increases with the number of cycles. Analysis of the dependence of stress ratio on the number of operation cycles shows that reduction of stress ratio decreases the durability of the studied material due to increase in the range of stresses in the cycle. It is obtained that increase of constant strain amplitude in the cycle relative to the established level by 10–15% corresponds to initial section of plastic deformation durability loss under cyclic loading. The homogeneity parameter determined in this case will characterize the limiting state of the material, which precedes its failure. Based on the analysis of experimental results, it is found that under conditions of realized loading, the damage kinetics curves for all investigated materials has a linear character. In different materials, the linear sections have different slopes. It can be assumed that the indicated slope of this curve characterizes the conditions of equilibrium between the processes of strain-hardening and softening of metal, achieved at the stage of steady creep. The presented results give grounds for using the homogeneity coefficient according to the LM-hardness method to assess the material condition of structural elements during the current monitoring of their condition. [ABSTRACT FROM AUTHOR]

Special features of computational assessment of dimensional change of WWER-1000 reactor core baffle during the reactor operation are discussed. The paper gives results of computational analysis of a change in shape of core baffle, which was performed by applying up-to-date approaches of modeling the irradiation-induced swelling of constrained austenitic steels under the action of neutron irradiation and elevated temperatures. The results have been obtained by using median and conservative values of parameters of the temperature and dose dependence of free swelling of austenitic steel Kh18N10T. The authors have set out the fundamental principles of elastic-plastic stress-strain analysis of the reactor core baffle and core barrel, taking into account the irradiationinduced swelling deformation and contact interaction conditions. The finite-element analysis is based on a FEM mixed scheme that ensures a continuous approximation both for displacements as well as stresses and strains, thus providing a high-accuracy determination of the stress-strain state. The calculations were carried out in the two-dimensional definition for the baffle cross-section with the maximum damaging dose and irradiation temperature in the baffle height, assuming a generalized plane-strain deformation. The calculated results are given for the reactor full-power operation and scheduled shutdown for re-fueling at the end of the charge life. According to the calculation data, disregarding the irradiation-induced swelling deformation leads to an incorrect assessment of the change in shape of the core baffle during its operation, while the use of the accepted free swelling model gives too conservative results on the shape change, even within the designed lifetime. The influence of the mean normal stress on the irradiation-induced swelling of metal makes the principal contribution to the change in shape of the core baffle. During the reactor operation beyond the designed lifetime there occurs a local contact between the core baffle and the core barrel in the zone of the largest-diameter circular opening of the longitudinal cooling channel and the port channel for coolant flow between the baffle and the barrel. The paper gives results of the analysis of the change in shape of the baffle in modeling of the contact conditions taking into consideration the temperature re-distribution due to deviation from the design coolant passage conditions in the zone where the baffle is in contact with the barrel. In the case of using the median dependence of the free swelling, no loss of the nominal gap between the core baffle and the core barrel is observed within the designed lifetime. The computational assessment using the conservative parameters of the irradiation-induced swelling leads to a distinct decrease of the gap between the core baffle and the core barrel and a local contact between them at the end of the designed lifetime. The residual gap between the spacer grids of edge fuel assemblies and the baffle faces is ensured in the case of the median and conservative dependence of the irradiation-induced swelling. [ABSTRACT FROM AUTHOR]

The geotemperature can reach 60°C at mining depth of 2000 m. The physical and mechanical properties of rocks will change with geotemperature, affecting the stress state of surrounding rock in deep excavation. In this paper, a thermodynamic model is applied to describe the stress and deformation process of rock material through the free energy function and dissipation equation, and yield surface, flow rule and plastic function are not considered in the elastic-plastic model, which greatly simplifies the calculation process. The developed finite element simulation program used to simulate the change of the stress between the rock and shaft wall. The temperature change induces thermal stresses between surrounding rock and shaft wall, especially at their interface. The results provide worthy support for the shaft failure and disaster prevention in deep engineering. [ABSTRACT FROM AUTHOR]

Stress is one of the most important factors in metal-to-metal sealing. In this paper, two methods (theoretical and empirical) were adopted to calculate the normal stress of the brass sealing surfaces against different ultrahigh pressure liquid. The theoretical formula was derived in terms of force balance, and the empirical formula was obtained by polynomial curve fitting, which the fitted data were from simulated results; besides, the results calculated by using the empirical formula agree well with the results by theoretical formula. Meanwhile, the equivalent stresses of the brass seal, normal stress and contact stress on the brass seal surfaces were simulated by finite element method, and the simulated results indicated these stresses are increased with the increase of liquid pressure, and the maximum stresses always appear on the tip of the brass seal. [ABSTRACT FROM AUTHOR]

The paper presents the results of the application of the refined calculation guidelines to the analysis of the stress-strain state and fracture resistance of the equipment elements of the NPP primary circuit system with WWER reactor, in particular, the cylindrical part and the zone of the reactor pressure vessel inlet nozzle, coolant collector welded joint in a steam generator, baffle, and reactor internals' shaft under the operating and emergency modes of thermomechanical loading. The calculation methodology is based on the use of the modern models and methods of solution to the nonlinear boundary tasks of non-isothermal thermal viscoplasticity and tasks of fracture mechanics using the refined mixed schemes of the finite element method with increased accuracy. They allow one to obtain reliable solutions to the tasks considering the deformation history of thermomechanical loading, modern concepts of fracture mechanics and approaches to the modeling of brittle-viscous fracture defects, irradiation swelling and creep of metal, as well as as the structural elements, under the conditions of elevated temperature, intensive neutron irradiation and nonstationary modes of thermomechanical loading. The authors obtained and analyzed the calculation results for the cylindrical part and zone of the inlet nozzle of the WWER-1000 reactor pressure vessel, coolant collector welded joint in a steam generator, baffle, and reactor internals' shaft using the proposed guidelines. The results imply the possibilities of the proposed recommendations and make it possible to analyze some general tendencies and features of the application of the refined calculation models to justify the strength and life extension of the NPP structural elements under investigation. [ABSTRACT FROM AUTHOR]

The paper presents the results of an analysis of the correctness of constitutive equations of irradiation creep, which describe non-isothermal processes of inelastic deformation, taking into account the irradiation swelling and irradiation creep of material under the conditions of neutron irradiation, high temperatures, and damaging dose. Current models of irradiation swelling and irradiation creep, which take into account the damaging dose, irradiation temperature, and the effect of stress state and accumulated irreversible strain on the processes of swelling and creep of material, are considered. The conditions under which dissipation power and the power developed by additional stresses on additional deformations do not decrease during loading under neutron irradiation conditions have been studied. On the basis of the obtained energy inequalities, which generalize Drucker's postulate for the irradiated material, the conditions that ensure the correctness of the formulated creep equations have been determined. The results of an analysis of the correctness conditions for irradiation creep equations showed that taking into account accumulated irreversible strain in the confined swelling model contributes to the relaxation of restrictions on the possible swelling of the material and initial data, which ensure the correctness of the constitutive equations of irradiation creep. [ABSTRACT FROM AUTHOR]

In view of the problem complexity, numerical methods, mainly finite and boundary element methods, are fairly widely used in the calculation of the static deformation of composite shells. The paper presents a new approach to the calculation of the static deformation of composite cylindrical shells using potential theory methods, which made it possible to obtain a solution to the set problem in the closed analytical form. Longitudinally infinite cylindrical shells, which are sequentially rigidly joined together (by clamping the outer edges of the formed composite structure), are considered. Orthogonal curvilinear coordinates in the middle of each of the cylindrical shells have been chosen. The problem has been solved in displacements. The system of differential equations of the static deformation of each of the cylindrical shells being part of the compound body was written according to the Vlasov shallow shell theory. The composite structure was under the action of a normal surface load. The expressions for internal forces and moments are given in terms of the components of the vector of displacements and the corresponding derivatives of them. For the system of differential equations, an exact solution has been found. The problem was solved by the method of variation of arbitrary constants. To determine the integration constants, the rigid joint conditions of cylindrical shells (from physical considerations) and the generally known conditions of rigid clamping of the edges of a compound body have been formulated. A system of linear algebraic equations for the desired constants has been derived. As a result of solving the system and substituting the found constants into the expressions for displacement vectors, the final solution of the problem in the form of potential images has been obtained with the aid of constructed Green matrices for this problem. The calculation method is illustrated by some numerical results, which describe the stress state of the object under investigation, composed of two in-series connected sections, as a function of the wavelength of the cylindrical shells. Analysis of the stress state characteristics shows that both bending moment and transverse force increase with decreasing wavelength of the cylindrical sections. This can be accounted for by the way of joining the cylindrical shells in the composite structure. Deformation schemes of composite cylindrical shells (under unilateral normal load) are presented with a purely illustrative purpose as evidence of the capabilities of the proposed method. [ABSTRACT FROM AUTHOR]

Circular bars are widespread elements in building and mechanical engineering. They allow one to enhance the strength of the multilayer composite materials along with their weight reduction. However, their analytical modeling is developed rather poorly, which creates additional obstacles in their efficient design. The paper presents the results of the exact analytical solution to the plane bending task of elasticity theory for the multilayer beam with a circular axis under normal uniform loading on its longitudinal surfaces considering the cylindrical orthotropy of its layers' materials. The problem has been solved using the methods of linear elasticity theory based on the continual approach where the circular bar is considered as a solid with the elastic characteristics varying in the radial direction. The solution for the shear stresses is assumed using the known distribution in the cross section. Therefore, the solution to the problem is reduced to the determination of two unknown functions of stress distribution throughout the section height. The system of linear differential equations has been obtained for the determination of the sought functions and unknown functions of integration in the process of the solution to the equations of plane theory considering the variable elastic characteristics. General analytical solutions for uniform and discontinuous-nonuniform layers from cylindrically orthotropic and isotropic materials have been developed. The influence of transverse shear deformation and compression on the characteristics of the stress-strain state of a cantilever three-layer beam with a semicircular axis is theoretically investigated. The obtained relations allow us to predict the stress-strain state of circular multilayer beams, as well as to build applied methods for solving problems of strength, rigidity, and optimal design of such structural elements. [ABSTRACT FROM AUTHOR]

This paper proposes an analytical model for the stress-strain state in a welded joint with a hard single-V butt weld. Analytical expressions for the stress-strain state in both the hard weld and the mild main material subjected to elasto-plastic deformation are proposed. In order to verify the proposed expressions, a finite element simulation of the stress-strain state in a welded joint with a hard single-V butt weld was carried out and the results were compared to the analytical results obtained applying the proposed analytical model. The analytical solution was basically consistent with the finite element analysis results. The proposed analytical model can be used in design practice for assessment of the stress-strain state in welded joints. [ABSTRACT FROM AUTHOR]

The statistical analysis performed on the defectiveness of rails in the Kiev subway railway shows that the main cause of the occurrence of most defects is the contact fatigue of the rail material. The paper presents modern concepts of crack growth in the railhead. It has been found that one of the most promising directions of studying the stress-strain state of rails and the crack growth process is a numerical simulation, which results on the contact interaction between rails and subway rolling stock wheels are presented. During the simulation, the problem was solved in an elastic formulation. We considered R50, R65, and UIC60 rail profiles, standard railway wheels, and wheels whose tire profile was developed by the Minetek closed joint-stock company. The conditions for the rail–wheel interaction corresponded to train movement on the straight section of the track without slipping. The effect of the wheel tire profile on the contact stress level in rails of different types has been assessed. Comparison of the maximum equivalent stress levels for a different combination of rail and wheel types shows that the best combination (in terms of reducing the contact stress level) for the straight sections of the subway track is an R50 rail with a gradient of 1 in 20 and 1 in 10 taper wheel, whose profile corresponds to GOST 9036-88. When wheels with the profile developed by the Minetek company are used, the maximum equivalent stress level in the contact zone is over 1000 MPa for all rail types. It is higher than the yield strength of rail steel, which will accelerate wear and give rise to low-cycle fatigue cracks with subsequent formation of contact fatigue defects. [ABSTRACT FROM AUTHOR]

In this paper, reinforced thermoplastic pipes (RTP) were studied under various loads. A total of five groups of specimens were designed to study the mechanical properties of RTPs under internal pressure, bending, a combination of internal pressure and bending moment, external pressure, and tension. This study obtained the bursting pressure of RTPs under internal pressure, the minimum bending radius under the bending moment, and the failure pressure under external pressure. At the same time, the mechanical properties of RTPs under various loads were analyzed using the finite element analysis. Analytical results agree well with the experimental ones. The finite element model established in this paper can be used for further research on the mechanical properties of RTPs. [ABSTRACT FROM AUTHOR]

The paper considers the results of determining the vibrodiagnostic indicators of the presence of various mode I breathing transverse cracks in rod elements of rectangular and circular cross section with different boundary conditions under longitudinal vibrations. Relative second harmonic amplitudes in the vibration spectrum at the main and superharmonic resonance of the first eigenmode of cantilever rods without mass and with a mass at the end and rods with the ends free for longitudinal displacements under forced and kinematic vibration excitation were taken as diagnostic indicators. To determine the above indicators, analytical and numerical bending vibration methods considered before are used. In the analytical solution, the nonlinearity parameter of the vibrating system is calculated using the corresponding values of stress intensity factors. The numerical solution is performed on the basis of eight-node finite element models with the representation of a breathing crack as a mathematical cut and the treatment of a contact problem in the formulation providing mutual nonpenetration between crack faces. Plots of the values of diagnostic indicators as a function of relative crack depth, crack location and the site of measurement of longitudinal displacements have been obtained. Comparisons of values of diagnostic indicators with the value of relative change in natural vibration frequency are presented. It has been shown that at the main resonance, the numerical solution confirms the pronounced effect of localization of diagnostic indicators in the crack region. It has been found that at the superharmonic resonance, the value of the vibrodiagnostic indicator is two orders of magnitude higher than that of the indicators at the main resonance, but the effect of their localization near the crack does not practically manifest itself. Some localization is observed for the absolute values of the second harmonic, and only for longitudinal strain, there is a strongly pronounced effect. A comparison of the obtained values of diagnostic indicators with the data for bending vibrations is given. It is noted that in spite of basically lower indicators under longitudinal vibrations, they have an advantage in terms of the possibility to diagnose symmetric both surface and internal breathing cracks. [ABSTRACT FROM AUTHOR]

In this paper, optimum test plans of step-stress partially accelerated life tests are developed using failure-censored data from Burr type-XII distribution. The maximum likelihood approach is applied to obtain the estimates of the acceleration factor and the parameters of the distribution. The minimization of the generalized asymptotic variance of the maximum likelihood estimators of the model parameters is used as an optimality criterion to develop optimum plans of the step-stress partially accelerated life tests. For illustrative purposes, simulation studies are presented. [ABSTRACT FROM AUTHOR]

For planning of thermal fatigue tests of materials and comprehensive analysis of their results, it is proposed to use the thermal cyclic test maps (TC-maps) that allow tracing the strain development in a thermal cycle. TC-maps illustrate the diagrams of the temperature-dependent elastic strain, which corresponds to the yield strength of the material, and the free strain variation under constraint conditions. This paper presents the procedure of thermal cycle test map compiling for some materials and their physical as well as mechanical properties. The useful information obtained from the TC-maps is exemplified by some heat-resistant alloys employed for the production of gas-turbine engine blades. [ABSTRACT FROM AUTHOR]

The paper provides the strength analysis performed for POLYITAN-2 nano-satellite under quasistatic overload conditions arising at the ascent stage. An efficient solid-state model together with its corresponding finite element model has been developed for nano-satellite. The numerical investigation of the stress-strain state of nano-satellite has been performed using the ANSYS software package. The maximum relative displacements of structural elements, as well as safety factors, have been determined. Different strength criteria were analyzed for the strength assessment of nano-satellite structural elements made of composite materials. It is found the considered POLYITAN-2 structure satisfies the critical strength and stiffness requirements. [ABSTRACT FROM AUTHOR]

The paper deals with the numerical stress calculation in the flexspline tooth rim of the harmonic drive. Due to the complex geometry of the toothed ring in the flexspline, the teeth were modeled as a ring, which height corresponded to the particular stress concentration in the teeth. To study the effect of type of wave generator on the stress distribution in the flexspline, the following models were elaborated: two-roller, four-roller, cam, and disk. The stress calculations were performed for the two cases: a zero torque load and the torque load value, corresponding to the true operation conditions of the hermetic harmonic drive. [ABSTRACT FROM AUTHOR]

The paper presents the numerical investigation on the stress-strain state of single- and two-layer spheres with spherically transtropic radially reinforced layers under a centrally symmetric internal explosion. A comparative analysis is made between two widely used methods of modeling the explosive loading. The influence of the reinforcing fiber volume fraction and the alternation of layers on the strength of shells is investigated. [ABSTRACT FROM AUTHOR]

Molecular dynamics simulation was employed to make the model of crack propagation for singlecrystal γ-TiAl alloy. The effects of the angle between a microcrack and loading direction on crack propagation were studied through the analysis of the atomic configurations and stress-strain curves in the paper. The results show that the time for the emission of first dislocation and the yield stress value decrease with the angle. The crack propagation occurs by the submain crack mechanism, which becomes more obvious as the angle increases and the number of stacking faults and stair-rod dislocations decreases. [ABSTRACT FROM AUTHOR]

The paper addresses some aspects of inclusion of loading history in the fracture strength analysis of reactor pressure vessels under thermal shock conditions. The strength assessment of a reactor pressure vessel and its lifetime extension are shown to essentially depend on reliability of results of elastic-plastic modeling of stress-strain kinetics and determination of design values of the fracture mechanics parameters. The present findings of the finite-element analysis demonstrate that the loading history must be taken into account in the determination of the temperature dependence of stress intensity factor for a postulated specified crack. It is shown that, in the fracture toughness analysis of a reactor pressure vessel, the temperature dependence of the stress intensity factor has to be derived from the results of the analysis of kinetics and mode of loading of metal at the crack tip under thermal shock conditions. For construction of the above dependence, we proposed approach, which accounts for the active loading and unloading processes occurring in the metal in the crack front vicinity. Incorporation of the loading history into the analysis of the temperature dependence of the stress intensity factor using the proposed approach forcan permit revealing some additional margin of strength during the substantiation of lifetime extension for a reactor pressure vessel under thermal shock conditions. [ABSTRACT FROM AUTHOR]

The paper presents the analysis of analytical models to determine the stress state in the substrate-coating system, when a load is applied to the substrate. The results obtained with these models are shown to differ. It is noted that the advantage of the analytical methods as compared to the numerical analysis is the possibility to calculate stresses in the singularity region in the vicinity of the free edge of the coating. The character of the shear stress distribution is analyzed using the analytical models. Examples of using different approaches to determine the critical shear stresses that define the adhesive strength of coatings are given. The analysis of literature sources shows that both simple and more sophisticated analytical models are employed in the investigation of the adhesive strength of coatings. [ABSTRACT FROM AUTHOR]

The paper describes the method of initial parameters which is used for stress analysis of complex branched piping systems under static loading as well as under natural and forced harmonic vibrations, including the case of kinematic loading by displacement amplitudes. For the purpose of modeling arbitrary curved elements, in particular three-dimensional ones, the authors propose an inertialess rotary element of zero length, which turns coordinate axes of neighbor elements. The paper demonstrates the potentialities of the method for vibrodiagnostics of piping. [ABSTRACT FROM AUTHOR]

This paper presents results of the analysis of numerical simulation of rotary compression process of hollow ball forging. Numerical analysis is conducted based on the finite element method using the Simufact Forming software. The methods of hollow ball forming are discussed with presentation of the geometrical model applied in calculations and the obtained rotary compression process description. The simulation is conducted under three-dimensional strain conditions. Strain, stress and temperature distributions are determined. The diagrams of forces and rotary moments of the hollow forging compression process are given. The described results of the numerical analysis confirm the possibility of producing the hollow balls by means of rotary compression with the use of billet in the form of a pipe part. [ABSTRACT FROM AUTHOR]

The paper addresses the temperature and thermoelastic states of a single-crystal blade with a complex vortex cooling system and passages for cooling air outflow. The problem of determination of stress-strain state of the blade at hand under the action of temperature fields and centrifugal forces is solved by the finite element method. The authors study the influence of azimuth orientation of crystallographic axes on the distribution and magnitude of thermoelastic stresses in the blade volume. [ABSTRACT FROM AUTHOR]

In this paper, the extended finite element method has been used to evaluate the fatigue life of cracked specimens in presence of bi-material interfaces. The standard finite element approximation is modified by adding appropriate enrichment functions in order to take into account the effect of these discontinuities present in the domain. The level set method is used to track different discontinuities in the domain. The stress intensity factors are calculated by the interaction integral approach. Finally, several numerical problems are presented to demonstrate the effect of these bi-material interfaces on fatigue crack growth. [ABSTRACT FROM AUTHOR]

Accelerated life testing (ALT) is an effective way to assess the lifetime of a product. Due to the complex nature of its testing profile, it is difficult to carry out temperature cycling ALT. This paper establishes a modified Norris-Landzberg model as acceleration model, and proposes the optimum design method of temperature cycling ALT. First, the FEA method is used to study the influence of temperature cycling profile parameters on the thermal fatigue life of 63Sn-37Pb solder joints. Then, a modified Norris-Landzberg model is proposed by introducing ramp time and dwell time with an added weight value. Finally, the temperature cycling ALT is regarded as a special multi-stress ALT to study its optimum design method. The uniform design theory is used to determine the combined mode. The optimum model is established with the objective of minimizing the asymptotic variance of the estimation of median lifetime under normal use conditions, and the simulation example shows the workability of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents the experimental justification of the applicability of a rapid method for the life assessment of heat-resistant steels under cyclic loading in a multiaxial stress state with consideration of metal damage. [ABSTRACT FROM AUTHOR]

The paper presents a mathematical model of the non-localized fatigue damage accumulation process in rubberlike materials. A relation for the determination of the constants of the corresponding equation with allowance for known fatigue curve characteristics, in particular for their random spread, is proposed. Computational relationships for the determination of the probabilistic characteristics of damage have been derived. Experimental data for the determination of realization of the fatigue accumulation process in rubber specimens, which are in good agreement with theoretical results, are considered. [ABSTRACT FROM AUTHOR]

The paper presents the stress-strain state simulation of the compound technical structure - vulcanizer diaphragm. A set of working plates in the form of a circular plate with the thickness discretely varied in the radial direction is modeled. An algorithm to solve the contact problem is developed. The obtained calculation results are compared with the experimental ones to demonstrate their practical use. [ABSTRACT FROM AUTHOR]

The paper presents results of an analysis of the gas-dynamic control of flow around the guide blades of axial compressor stage for the vibration intensity of rotor blades. It has been shown that gas-dynamic action on flow around blades equalizes the flow velocity field before the rotor and reduces the level of resonant stresses in blades in the case of their resonant excitation. [ABSTRACT FROM AUTHOR]

The paper presents the results of investigation into the regularities of deformation and kinetics of damage accumulation in heat-resistant steels 10GN2MFA and 15Kh2MFA under different modes of loading at a complex stress state. [ABSTRACT FROM AUTHOR]

The paper considers the irreversible deformation of steam turbine rotors due to the circumferential non-uniformity of the material mechanical properties based on the numerical analysis of their three-dimensional stress-strain state. It is shown that this non-uniformity can be one of the causes for the occurrence and development of progressive creep deflection of high-temperature rotors that have been in long-term operation and also their bending in case of excess of the rated rotational speed. [ABSTRACT FROM AUTHOR]

The paper presents the results of the computational experiments to determine the regularities in the variation of the static stress state characteristics of blades as a function of the inclination angle value of the shroud contact surfaces relative to the plane of rotor wheel rotation with a consideration of the action of centrifugal gravity forces and high temperatures of the gas flow. [ABSTRACT FROM AUTHOR]

The paper considers the possibility of determining stresses and strains in elastoplastic deformed body from hardness spreading parameters. [ABSTRACT FROM AUTHOR]

The paper addresses the mechanical behavior of carbon steel 20 in asymmetric loading under the conditions of plane stress state that occurs in a thin-walled specimen in tension-compression and alternating torsion. The asymmetric cyclic loading of specimens was carried out in a stress-controlled mode along three paths with a frequency of 0.1 Hz with a base up to 1200 cycles. Cyclic stress-strain diagrams have been constructed for the specimens under tension-compression, alternating torsion, and proportional loading. The curves of von Mises equivalent ratcheting strains have been plotted. The highest ratcheting rate is shown to take place in the tension-compression loading case. [ABSTRACT FROM AUTHOR]

It is not easy to obtain more failure data from products with high quality and long life at normal (use) condition. Thus, accelerated tests are needed in this respect. This paper considers the constant stress partially accelerated life tests with type-I censoring under Weibull distribution. The maximum likelihood estimators of the model parameters are derived. Partially accelerated life tests plans are developed such that the generalized asymptotic variance of the maximum likelihood estimators of the model parameters is minimized. The plan is to specify the proportion of test units that should be allocated to run under use condition. Simulation studies are made for illustrative purposes. [ABSTRACT FROM AUTHOR]

This paper considers the basic principles of the most widespread methods for determining typical states of a mode I through crack in specimens and structures of sheet metals that are fractured under conditions close to the plane stress state. The results of experimental investigations are presented which make it possible to judge of the relative advantages and disadvantages of these methods from the standpoint of their possible use in engineering assessments of the integrity and remaining strength of thin-wall structures. [ABSTRACT FROM AUTHOR]

Accelerated life testing (ALT) and partially accelerated life testing (PALT) are frequently used in modern reliability engineering. ALT and PALT are run to obtain information on the life of the products and materials in a shorter time and at lower cost. The experimental units are subject to stress conditions that are more severe than those encountered in normal use condition to induce early failures. ALT or PALT can be carried out using constant, step, progressive, cyclic and random stress loadings. This paper considers the problem of estimating the generalized exponential (GE) distribution parameters and the acceleration factor under constant-stress PALT model. The main objective is to derive the maximum likelihood estimators (MLEs) of the parameters of the GE distribution and the acceleration factor when the data are type-II censored from constant-stress PALT. Also, the performance of the MLEs is investigated numerically for different sample sizes and different parameter values using the mean square error. In addition, the approximate confidence intervals of the model parameters are constructed. Moreover, the likelihood ratio bounds (LRB) method is used to obtain confidence bounds of the model parameters when the sample size is small. For illustration, a simulation study is conducted. It is observed that the simulation results support the theoretical findings. [ABSTRACT FROM AUTHOR]

The paper provides some results of the investigation of the influence of stress state type on accumulation of dispersed damages in structural carbon steel sheet under repeated static biaxial tensile loading. It is shown that the lowest damage accumulation ability of the metal is observed under biaxial tension with a biaxiality index ranging between 0.25 and 0.3. [ABSTRACT FROM AUTHOR]

Fracture occurs at interface corners due to stress singularity which generates as a result of material discontinuity and geometrical configuration. In elastic stress field near a bimaterial notch tip, eigenvalues extracted from Airy’s stress function approach determine the order of singularity. In this paper, the characteristic equation of elastic stress field near bimaterial notches is investigated. The study is done on singular eigenvalues as well as the first non-singular eigenvalue which has not been well studied before. First, different combination of materials and geometrical configurations for two of the most applicable paths in the Bogy diagram (β = 0, β = α/4) were studied and the results were comprehensively discussed. It was shown that the geometrical and materials configurations near a bimaterial notch tip can significantly affect on the stress singularity near these corners. Finally, the areas between two lines β = 0 and β = α/4 in the Bogy diagram with high stress singularities were determined and discussed for both the first and second singular eigenvalue. [ABSTRACT FROM AUTHOR]

The paper outlines the methodological approach and the related software package, which permit determining stress-strain state and defect rate for full-scale crack-containing objects. The method is based on computational assessment of the above-mentioned parameters on the condition of minimum of the objective function that describes discrepancy between the experimental data arrays and the results of numerical solutions to model problems using the finite-element method. [ABSTRACT FROM AUTHOR]

The paper addresses the well-known (from available publications) phenomenological strength criteria for anisotropic materials, which are most widely used in application software. [ABSTRACT FROM AUTHOR]

Experimental testing and non-linear finite element analysis using discrete reinforcement modeling of six numbers of reinforced concrete beams under four-point bending are presented in this paper. Finite element modeling of reinforced concrete beams is carried out using ANSYS 12.0, and the critical values of the results are also compared with analytical values calculated using IS 456: 2000 codal provisions. Wide-range graphical display of the results such as deflected shape of the beam, stress-strain variation along the length and depth of the beam and crack propagation is generated by creating a batch file using the ANSYS parametric design language. Comparison is made between the test results, finite element analysis and analytical values with respect to initial crack formation and the ultimate capacity of beams, in order to have a wide understanding on the behavior, which may reduce the physical destructive laboratory testing for the future researchers. [ABSTRACT FROM AUTHOR]

The paper provides a review of the known (from available publications) methods and findings of experimental studies of stress-strain state and strength of multilayer thick-walled anisotropic cylinders under dynamic loading. [ABSTRACT FROM AUTHOR]

The paper presents some findings of numerical investigations of torsional vibrations in steam turbine shafting in the turbogenerator abnormal operation modes (short circuit, random paralleling start, etc.). The shafting vibrations are shown to be essentially dependant on the reaction torque surge parameters (magnitude, duration, and form). For three types of the reaction torque surge a comparative hazard analysis is performed from the standpoint of initiation of cyclic damage in the rotor material and the risk of shafting failure. [ABSTRACT FROM AUTHOR]