Search

There is an extensive need for surface sensors for applications such as tactile sensing for robotics, damage and strain detection for structural health monitoring and leak detection for buried structures. One type of surface sensor is electrical impedance tomography (EIT)-based sensing skins, which use electrically conductive coatings applied on the object's surface to monitor physical or chemical phenomena on the surface. In this article, we propose a sensing skin with two electrically coupled layers separated by an insulator. Based on electrical measurements, the spatial distribution of the electrical coupling between the layers is estimated. This coupling is sensitive to both the pressure distribution on the surface and water entering between the layers through a leak. We present simulations and experimental studies to evaluate the feasibility of the proposed method for pressure sensing and leak detection. The results support the feasibility of the proposed method for both of these applications.

Multifunctional sensors have played a crucial role in constructing high-integration electronic networks. Most of the current multifunctional sensors rely on multiple materials to simultaneously detect different physical stimuli. Here, we demonstrate the large piezo-pyroelectric effect in ferroelectric Pb(Mg 1/3 Nb 2/3 )O 3 -PbTiO 3 (PMN-PT) single crystals for simultaneous pressure and temperature sensing. The outstanding piezoelectric and pyroelectric properties of PMN-PT result in rapid response speed and high sensitivity, with values of 46 ms and 28.4 nA kPa -1 for pressure sensing, and 1.98 s and 94.66 nC °C -1 for temperature detection, respectively. By leveraging the distinct differences in the response speed of piezoelectric and pyroelectric responses, the piezo-pyroelectric effect of PMN-PT can effectively detect pressure and temperature from mixed-force thermal stimuli, which enables a robotic hand for stimuli classification. With appealing multifunctionality, fast speed, high sensitivity, and compact structure, the proposed self-powered bimodal sensor therefore holds significant potential for high-performance artificial perception.

Traditional systems for indoor pressure sensing and human activity recognition (HAR) rely on costly, high-resolution mats and computationally intensive neural network-based (NN-based) models that are prone to noise. In contrast, we design a cost-effective and noise-resilient pressure mat system for HAR, leveraging Velostat for intelligent pressure sensing and a novel hyperdimensional computing (HDC) classifier that is lightweight and highly noise resilient. To measure the performance of our system, we collected two datasets, capturing the static and continuous nature of human movements. Our HDC-based classification algorithm shows an accuracy of 93.19%, improving the accuracy by 9.47% over state-of-the-art CNNs, along with an 85% reduction in energy consumption. We propose a new HDC noise-resilient algorithm and analyze the performance of our proposed method in the presence of three different kinds of noise, including memory and communication, input, and sensor noise. Our system is more resilient across all three noise types. Specifically, in the presence of Gaussian noise, we achieve an accuracy of 92.15% (97.51% for static data), representing a 13.19% (8.77%) improvement compared to state-of-the-art CNNs.

In this study, we developed a novel wireless, passive pressure-sensing method functional at cryogenic temperatures (-196 °C). The currently used pressure sensors are inconvenient and complicated in cryogenic environments for their weak low-temperature tolerances and long wires for power supply and data transmission. We propose a novel pressure-sensing method for cryogenic applications by only using low-temperature-tolerant passive devices. By innovatively integrating a magnetoresistor (MR) on a backscattering antenna, the pressure inside a cryogenic environment is transferred to a wirelessly obtainable return loss. Wireless passive measurement is thus achieved using a backscattering method. In the measurement, the pressure causes a relative displacement between the MR and a magnet. The MR's resistance changes with the varied magnetic field, thus modulating the antenna's return loss. The experimental results indicate that our fabricated sensor successfully identified different pressures, with high sensitivities of 4.3 dB/MPa at room temperature (24 °C) and 1.3 dB/MPa at cryogenic temperature (-196 °C). Additionally, our method allows for simultaneous wireless readings of multi sensors via a single reading device by separating the frequency band of each sensor. Our method performs low-cost, simple, robust, passive, and wireless pressure measurement at -196 °C; thus, it is desirable for cryogenic applications.

This article is devoted to the study of the correlation between the emotional state of a person and the posture of his or her body in the sitting position. In order to carry out the study, we developed the first version of the hardware-software system based on a posturometric armchair, allowing the characteristics of the posture of a sitting person to be evaluated using strain gauges. Using this system, we revealed the correlation between sensor readings and human emotional states. We showed that certain readings of a sensor group are formed for a certain emotional state of a person. We also found that the groups of triggered sensors, their composition, their number, and their location are related to the states of a particular person, which led to the need to build personalized digital pose models for each person. The intellectual component of our hardware-software complex is based on the concept of co-evolutionary hybrid intelligence. The system can be used during medical diagnostic procedures and rehabilitation processes, as well as in controlling people whose professional activity is connected with increased psycho-emotional load and can cause cognitive disorders, fatigue, and professional burnout and can lead to the development of diseases.

Fiber-optic sensors are a powerful tool to investigate physical properties like temperature, strain, and pressure. Such properties make these sensors interesting for many applications including biomedical applications. Fiber sensors are also a great platform for distributed sensing by using the principles of optical frequency domain reflectometry. Distributed sensing is becoming more and more used to achieve high-resolution measurements and to map physical properties of biomaterials at small scale, thus obtaining 2D and 3D mapping of a particular area of interest. This work aims at building and investigating a 2D sensing carpet based on a distributed fiber sensing technique, to map local pressure applied to the carpet. The two-dimensional mapping is obtained by embedding a single-mode optical fiber inside a soft silicone carpet. The fiber has been bent and arranged in a specific configuration characterized by several parallel lines. Different fiber fixation methods have been investigated by means of a comparative analysis to perform better characterization and to achieve a more precise response of the carpet. The best pressure sensitivity coefficient (0.373 pm/kPa or considering our setup 1.165 nm/kg) was detected when the fiber was fully embedded inside the silicone carpet. This paper demonstrates the possibility of mapping a 2D distributed pressure over a surface with a resolution of 2 mm by 2 mm. The surface of investigation is 2 cm by 6 cm, containing 310 sensing points. The sensing carpet has been validated selecting several preferential positions, by testing the consistency of the results over different portions of the carpet., Competing Interests: The authors declare no conflict of interest.

The high demand for pressure devices with miniaturization and a wide bearing range has encouraged researchers to explore new high-performance sensors from different approaches. In this study, a sensitive element based on graphene in-plane compression properties for realizing pressure sensing is experimentally prepared using microelectromechanical systems (MEMS) fabrication technology; it consists of a 50 µm thick, 1400 µm wide square multilayer component membrane and a graphene monolayer with a meander pattern. The prepared sample is extensively characterized and analyzed by using various techniques, including atomic force microscopy, Raman spectroscopy, infrared spectroscopy, X-ray photoelectron spectroscopy, COMSOL finite element method, and density functional theory. The sensing performance of the new pressure sensor based on the sensitive element are obtained by theoretical analysis for electromechanical measurements of the sensitive element before and after low-temperature annealing in atmosphere. Results demonstrate that atmospheric annealing at 300 °C enhances the pressure sensing sensitivity by 4 times compared to pristine graphene without annealing, which benefits from the desorption of hydroxyl groups on the graphene surface during annealing. The sensitivity is comparable and even better than that of previous sensors based on graphene in-plane properties. Our results provide new insights into realizing high-performance MEMS devices based on 2D sensitive materials.

A simple and cost-effective calibration procedure for piezoresistive ink tactile pressure sensors is crucial for their use in geotechnical research applications. Such a procedure should be applicable in field conditions and require a minimum amount of equipment. The paper describes a new method for calibrating tactile pressure sensors with 8-bit sensels' output. The method is based on the approximation of a single sensel output and consideration of multiple calibration patches. The advantage of the developed method is using local high-pressure zones in calibration patches. The developed method has been successfully applied in calibration of two 5051-350 Tekscan sensors by means of three dead weights: 2 kg, 5 kg and 10 kg. One calibrated sensor was new, and another one had been previously used in the harsh environment of the ice tank in the experiment with model ice. The calibration curves for these two sensors did not reveal a significant difference. For 72% of the 150 obtained load patches in calibration, the absolute discrepancy of actual and calibrated load occurred to be less than 5%.

We present a solution for intelligent posture training based on accurate, real-time sitting posture monitoring using the LifeChair IoT cushion and supervised machine learning from pressure sensing and user body data. We demonstrate our system's performance in sitting posture and seated stretch recognition tasks with over 98.82% accuracy in recognizing 15 different sitting postures and 97.94% in recognizing six seated stretches. We also show that user BMI divergence significantly affects posture recognition accuracy using machine learning. We validate our method's performance in five different real-world workplace environments and discuss training strategies for the machine learning models. Finally, we propose the first smart posture data-driven stretch recommendation system in alignment with physiotherapy standards.

In this paper, a pressure sensor based on a metal diaphragm and lever structure is designed, the sensing principle and mechanical structure of this sensor are analyzed and simulated, and its sensitization effectiveness and temperature compensation are verified. The maximum deflections of metal diaphragms of different sizes and materials were compared, and it was found that the square beryllium bronze diaphragm with a thickness of 1 mm and a side length of 20 mm had good elastic properties. The influence of the FBG in different positions of the lever on the center wavelength is analyzed. The sensitivity of the bare FBG is markedly improved under the influence of the two structures of the square elastic diaphragm and the lever, with a typical pressure sensitivity of 3.35 nm/MPa at 3 mm to the left of the lever center. The purpose of temperature compensation is achieved by adding another FBG that measures the temperature, and the sensing sensitivity can be tuned by adjusting the position of the FBG. It can meet the detection needs of a small range and high sensitivity.

A diaphragm-based hermetic optical fiber Fabry-Pérot (FP) cavity is proposed and demonstrated for pressure sensing. The FP cavity is hermetically sealed using one-step CO 2 laser welding with a cavity length from 30 to 100 μm. A thin diaphragm is formed by polishing the hermetic FP cavity for pressure sensing. The fabricated FP cavity has a fringe contrast larger than 15 dB. The experimental results show that the fabricated device has a linear response to the change in pressure, with a sensitivity of -2.02 nm/MPa in the range of 0 to 4 MPa. The results demonstrate that the proposed fabrication technique can be used for fabricating optical fiber microcavities for sensing applications.

Highly sensitive and flexible composite sensors with pressure and temperature sensing abilities are of great importance in human motion monitoring, robotic skins, and automobile seats when checking the boarding status. Several studies have been conducted to improve the temperature-pressure sensitivity; however, they require a complex fabrication process for micro-nanostructures, which are material-dependent. Therefore, there is a need to develop the structural designs to improve the sensing abilities. Herein, we demonstrate a flexible composite with an enhanced pressure and temperature sensing performance. Its structural design consists of a multilayered composite construction with an elastic modulus gradient. Controlled stress concentration and distribution induced by a micropatterned structure between the layers improves its pressure and temperature sensing performance. The proposed composite sensor can monitor a wide range of pressure and temperature stimuli and also has potential applications as an automotive seat sensor for simultaneous human temperature detection and occupant weight sensing., Competing Interests: The authors declare no conflict of interest.

Existing acoustic test benches are usually costly devices based on proprietary designs, sensors, and acquisition devices. In this paper, a low-cost test bench for acoustic purposes is introduced. The design of the test bench takes into account not only the low-cost mechanical design, but also uses low-cost sensors and control boards. This test bench has been designed for a range of signals compatible with those used by thermoacoustic engines, but it can be useful for applications with similar requirements. Taking advantage of an auxiliary pressure reference, low-cost unidirectional differential pressure sensors can be used to significantly increase the accuracy of the sampling system. The acoustic and mechanical design and development are presented along with the sampling system and the sensors arrangement implemented. Both the sensor and sampling system are evaluated by comparison with a high-fidelity sound acquisition system. An unexpected effect on the time error values distribution of the low-cost acquisition system is found and described. Finally, the errors introduced by the system and the sensors in terms of time and pressure sampling are characterized. As a result, the low-cost system's accuracy has been satisfactory assessed and validated for the conditions expected in thermoacoustic experiments in terms of frequency and dynamic pressure., Competing Interests: The authors declare no conflict of interest.

The present study compared the mechanical, electrical, morphological, and piezoresistive characteristics of epoxy-based sensing nanocomposites fabricated with inclusions of hybridized networks of four different carbon nanomaterials (CNMs), such as carbon nanotube (CNT), graphene, carbon nanofiber (CNF), and graphite nanoplatelet (GNP). Enhancements in elastic modulus and electrical conductivity were achieved by CNT-graphene composites and CNT-CNF composites, and these were explained by the morphological observations carried out in the present study and experimental studies found in the literature. The greatest gauge factor was accomplished by the CNT-GNP composite, followed by the CNT-CNF composite among composites where the CNM networks were sufficiently formed with a content ratio of 3%. The two types of the composites outperformed the composites incorporating solely CNT in terms of gauge factor, and this superiority was explained with the excluded volume theory.

We describe here a platform for autonomous hand rehabilitation and telemonitoring of young patients. A toy embedding the electronics required to sense fingers pressure in different grasping modalities is the core element of this platform. The system has been realized following the user-centered design methodology taking into account stakeholder needs from start: clinicians require reliable measurements and the ability to get a picture remotely on rehabilitation progression; children have asked to interact with a pleasant and comfortable object that is easy to use, safe, and rewarding. These requirements are not antithetic, and considering both since the design phase has allowed the realization of a platform reliable to clinicians and keen to be used by young children., Competing Interests: The authors declare no conflict of interest.

We report on a novel optical microcavity sensing scheme by using the orthogonal demodulation Pound-Drever-Hall (PDH) technique. We found that larger sensitivity in a broad range of cavity quality factor (Q) could be obtained. Taking microbubble resonator (MBR) pressure sensing as an example, a lower detection limit than the conventional wavelength shift detection method was achieved. When the MBR cavity Q is about 10 5 -10 6 , the technique can decrease the detection limit by one or two orders of magnitude. The pressure-frequency sensitivity is 11.6 GHz/bar at wavelength of 850 nm, and its detection limit can approach 0.0515 mbar. This technique can also be applied to other kinds of microcavity sensors to improve sensing performance.

The LifeChair is a smart cushion that provides vibrotactile feedback by actively sensing and classifying sitting postures to encourage upright posture and reduce slouching. The key component of the LifeChair is our novel conductive fabric pressure sensing array. Fabric sensors have been explored in the past, but a full sensing solution for embedded real world use has not been proposed. We have designed our system with commercial use in mind, and as a result, it has a high focus on manufacturability, cost-effectiveness and adaptiveness. We demonstrate the performance of our fabric sensing system by installing it into the LifeChair and comparing its posture detection accuracy with our previous study that implemented a conventional flexible printed PCB-sensing system. In this study, it is shown that the LifeChair can detect all 11 postures across 20 participants with an improved average accuracy of 98.1%, and it demonstrates significantly lower variance when interfacing with different users. We also conduct a performance study with 10 participants to evaluate the effectiveness of the LifeChair device in improving upright posture and reducing slouching. Our performance study demonstrates that the LifeChair is effective in encouraging users to sit upright with an increase of 68.1% in time spent seated upright when vibrotactile feedback is activated.

We present a continuous-wave fiber cavity ringdown (FCRD) pressure-sensing method based on frequency-shifted interferometry (FSI). Compared with traditional CRD or FCRD techniques, this FSI-FCRD scheme deduces pressure by measuring the decay rate of continuous light exiting the fiber ringdown cavity (RDC) in the spatial domain (i.e., the CRD distance), without the requirement for optical pulsation and fast electronics. By using a section of fiber with the buffer layer stripped in the fiber RDC as the sensor head, pressures were measured within the range from 0 to 10.4 MPa. The sensitivity of 0.02356/(km∙MPa) was obtained with a measurement error of 0.1%, and the corresponding pressure resolution was 0.05 MPa. It was found that the measurement sensitivity can be improved by enlarging the interaction length of the sensor head. The results show the proposed sensor has the advantages of simple structure, low cost, high sensitivity, and high stability in pressure detection.

Organic Field-Effect Transistors (OFETs) are attracting a rising interest for the development of novel kinds of sensing platforms. In this paper, we report about a peculiar sensor device structure, namely Organic Charge-Modulated Field-Effect Transistor (OCMFET), capable of operating at low voltages and entirely fabricated with large-area techniques, i.e., inkjet printing and chemical vapor deposition, that can be easily upscaled to an industrial size. Device fabrication is described, and statistical characterization of the basic electronic parameters is reported. As an effective benchmark for the application of large-area fabricated OCMFET to the biomedical field, its combination with pyroelectric materials and compressible capacitors is discussed, in order to employ the proposed device as a temperature pressure sensor. The obtained sensors are capable to operate in conditions which are relevant in the biomedical field (temperature in the range of 18.5-50 °C, pressure in the range of 10²-10³ Pa) with reproducible and valuable performances, opening the way for the fabrication of low-cost, flexible sensing platforms., Competing Interests: The authors declare no conflict of interest.

A new fiber pressure sensor is proposed and analyzed in this paper. A commercial arc fusion splicer and pressure-assisted arc discharge technology are used here to fabricate a silica hollow microbubble from a common glass tube with the characteristics of a thin film. Then the single mode fiber is embedded into the microbubble to form a fiber Fabry-Perot interferometer by measuring the reflected interference spectrum from the fiber tip and microbubble end. As the wall thickness of the micro-bubble can reach up to several micrometers, it can then be used for measuring the outer pressure with high sensitivity. The fabrication method has the merits of being simple, low in cost, and is easy to control. Experimental results show that its pressure sensitivity can reach 164.56 pm/kPa and the temperature sensitivity can reach 4 pm/°C. Therefore, it also has the advantage of being insensitive to temperature fluctuation., Competing Interests: The authors declare no conflict of interest.