Search

In the realm of electrochemical nitrite detection, the potent oxidizing nature of nitrite typically necessitates operation at high detection potentials. However, this study introduces a novel approach to address this challenge by developing a highly sensitive electrochemical sensor with a low reduction detection potential. Specifically, a copper metal nanosheet/carbon paper sensitive electrode (Cu/CP) was fabricated using a one-step electrodeposition method, leveraging the catalytic reduction properties of copper's high occupancy d-orbital. The Cu/CP sensor exhibited remarkable performance in nitrite detection, featuring a low detection potential of −0.05 V vs. Hg/HgO, a wide linear range of 10~1000 μM, an impressive detection limit of 0.079 μM (S/N = 3), and a high sensitivity of 2140 μA mM−1cm−2. These findings underscore the efficacy of electrochemical nitrite detection through catalytic reduction as a means to reduce the operational voltage of the sensor. By showcasing the successful implementation of this strategy, this work sets a valuable precedent for the advancement of electrochemical low-potential nitrite detection methodologies. [ABSTRACT FROM AUTHOR]

Vibration sensors are widely used in many fields like industry, agriculture, military, medicine, environment, etc. However, due to the speedy upgrading, most sensors composed of rigid or even toxic materials cause pollution to the environment and give rise to an increased amount of electronic waste. To meet the requirement of green electronics, biodegradable materials are advocated to be used to develop vibration sensors. Herein, a vibration sensor is reported based on a strategy of pencil-drawing graphite on paper. Specifically, a repeated pencil-drawing process is carried out on paper with a zigzag-shaped framework and parallel microgrooves, to form a graphite coating, thus serving as a functional conductive layer for electromechanical signal conversion. To enhance the sensor's sensitivity to vibration, a mass is loaded in the center of the paper, so that higher oscillation amplitude could happen under vibrational excitation. In so doing, the paper-based sensor can respond to vibrations with a wide frequency range from 5 Hz to 1 kHz, and vibrations with a maximum acceleration of 10 g. The results demonstrate that the sensor can not only be utilized for monitoring vibrations generated by the knuckle-knocking of plastic plates or objects falling down but also can be used to detect vibration in areas such as the shield cut head to assess the working conditions of machinery. The paper-based MEMS vibration sensor exhibits merits like easy fabrication, low cost, and being environmentally friendly, which indicates its great application potential in vibration monitoring fields. [ABSTRACT FROM AUTHOR]

As power sources for Internet-of-Things sensors, thermoelectric generators must exhibit compactness, flexibility, and low manufacturing costs. Stretchable and flexible painted thermoelectric generators were fabricated on Japanese paper using inks with dispersed p- and n-type single-walled carbon nanotubes (SWCNTs). The p- and n-type SWCNT inks were dispersed using the anionic surfactant of sodium dodecylbenzene sulfonate and the cationic surfactant of dimethyldioctadecylammonium chloride, respectively. The bundle diameters of the p- and n-type SWCNT layers painted on Japanese paper differed significantly; however, the crystallinities of both types of layers were almost the same. The thermoelectric properties of both types of layers exhibited mostly the same values at 30 °C; however, the properties, particularly the electrical conductivity, of the n-type layer increased linearly, and of the p-type layer decreased as the temperature increased. The p- and n-type SWCNT inks were used to paint striped patterns on Japanese paper. By folding at the boundaries of the patterns, painted generators can shrink and expand, even on curved surfaces. The painted generator (length: 145 mm, height: 13 mm) exhibited an output voltage of 10.4 mV and a maximum power of 0.21 μW with a temperature difference of 64 K at 120 °C on the hot side. [ABSTRACT FROM AUTHOR]

This study presents a portable, low-cost, point-of-care (POC) system for the simultaneous detection of blood glucose and hematocrit. The system consists of a disposable origami microfluidic paper-based analytical device (μPAD) for plasma separation, filtration, and reaction functions and a 3D-printed cassette for hematocrit and blood glucose detection using a smartphone. The origami μPAD is patterned using a cost-effective label printing technique instead of the conventional wax printing method. The 3D-printed cassette incorporates an array of LED lights, which mitigates the effects of intensity variations in the ambient light and hence improves the accuracy of the blood glucose and hematocrit concentration measurements. The hematocrit concentration is determined quantitatively by measuring the distance of plasma wicking along the upper layer of the origami μPAD, which is pretreated with sodium chloride and Tween 20 to induce dehydration and aggregation of the red blood cells. The filtered plasma also penetrates to the lower layer of the origami μPAD, where it reacts with embedded colorimetric assay reagents to produce a yellowish-brown complex. A color image of the reaction complex is captured using a smartphone inserted into the 3D-printed cassette. The image is analyzed using self-written RGB software to quantify the blood glucose concentration. The calibration results indicate that the proposed detection platform provides an accurate assessment of the blood glucose level over the range of 45–630 mg/dL (R2 = 0.9958). The practical feasibility of the proposed platform is demonstrated by measuring the blood glucose and hematocrit concentrations in 13 human whole blood samples. Taking the measurements obtained from commercial glucose and hematocrit meters as a benchmark, the proposed system has a differential of no more than 6.4% for blood glucose detection and 9.1% for hematocrit detection. Overall, the results confirm that the proposed μPAD is a promising solution for cost-effective and reliable POC health monitoring. [ABSTRACT FROM AUTHOR]

Specialized cancer treatments have the potential to exploit glutamine dependence to increase patient survival rates. Glutamine diagnostics capable of tracking a patient's response to treatment would enable a personalized treatment dosage to optimize the tradeoff between treatment success and dangerous side effects. Current clinical glutamine testing requires sophisticated and expensive lab-based tests, which are not broadly available on a frequent, individualized basis. To address the need for a low-cost, portable glutamine diagnostic, this work engineers a cell-free glutamine biosensor to overcome assay background and signal-to-noise limitations evident in previously reported studies. The findings from this work culminate in the development of a shelf-stable, paper-based, colorimetric glutamine test with a high signal strength and a high signal-to-background ratio for dramatically improved signal resolution. While the engineered glutamine test is important progress towards improving the management of cancer and other health conditions, this work also expands the assay development field of the promising cell-free biosensing platform, which can facilitate the low-cost detection of a broad variety of target molecules with high clinical value. [ABSTRACT FROM AUTHOR]

Image compression is a vital component for domains in which the computational resources are usually scarce such as automotive or telemedicine fields. Also, when discussing real-time systems, the large amount of data that must flow through the system can represent a bottleneck. Therefore, the storage of images, alongside the compression, transmission, and decompression procedures, becomes vital. In recent years, many compression techniques that only preserve the quality of the region of interest of an image have been developed, the other parts being either discarded or compressed with major quality loss. This paper proposes a study of relevant papers from the last decade which are focused on the selection of a region of interest of an image and on the compression techniques that can be applied to that area. To better highlight the novelty of the hybrid methods, classical state-of-the-art approaches are also analyzed. The current work will provide an overview of classical and hybrid compression methods alongside a categorization based on compression ratio and other quality factors such as mean-square error and peak signal-to-noise ratio, structural similarity index measure, and so on. This overview can help researchers to develop a better idea of what compression algorithms are used in certain domains and to find out if the presented performance parameters are of interest for the intended purpose. [ABSTRACT FROM AUTHOR]

This document is a summary of a special issue of the journal Sensors, titled "Emerging AI+X-Based Sensor and Networking Technologies including Selected Papers from ICGHIT 2022–2023." The special issue features selected papers from the 10th and 11th International Conferences on Green and Human Information Technology (ICGHITs), which were held in Korea and Thailand. The conferences focused on the theme of "Emerging Artificial Intelligent (AI)+X technology" and "Hyper Automation + Human AI" respectively. The selected papers cover various topics such as network security, routing protocols, signal detection, and clustering mechanisms, all incorporating AI-based methods. The issue also includes papers on topics like secure authentication, distance estimation in RFID systems, energy optimization in smart homes, blockchain technology, and radar signal detection. The authors emphasize the importance of both technology and humanity in advancing green and information technologies. [Extracted from the article]

Iodine is an essential micronutrient for humans due to its fundamental role in the biosynthesis of thyroid hormones. As a key parameter to assess health conditions, iodine intake needs to be monitored to ascertain and prevent iodine deficiency. Iodine is available from various food sources (such as seaweed, fish, and seafood, among others) and dietary supplements (multivitamins or mineral supplements). In this work, a microfluidic paper-based analytical device (μPAD) to quantify iodide in seaweed and dietary supplements is described. The developed μPAD is a small microfluidic device that emerges as quite relevant in terms of its analytical capacity. The quantification of iodide is based on the oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) by hydrogen peroxide in the presence of iodine, which acts as the catalyst to produce the blue form of TMB. Additionally, powder silica was used to intensify and uniformize the colour of the obtained product. Following optimization, the developed μPAD enabled iodide quantification within the range of 10–100 µM, with a detection limit of 3 µM, and was successfully applied to seaweeds and dietary supplements. The device represents a valuable tool for point-of-care analysis, can be used by untrained personnel at home, and is easily disposable, low-cost, and user-friendly. [ABSTRACT FROM AUTHOR]

By focusing our attention on nitrogen components in plants, which are important for cultivation management in data-driven agriculture, we developed a simple, rapid, non-chemical and simultaneous quantification method for proteinic and nitrate nitrogen in a leaf model based on near-infrared (NIR) spectroscopic information obtained using a compact Fourier Transform NIR (FT-NIR) spectrometer. The NIR spectra of wet leaf models impregnated with a protein–nitric acid mixed solution and a dry leaf model obtained by drying filter paper were acquired. For spectral acquisition, a compact MEMS (Micro Electro Mechanical Systems) FT-NIR spectrometer equipped with a diffuse reflectance probe accessory was used. Partial least square regression analysis was performed using the spectral information of the extracted absorption bands based on the determination coefficients between the spectral absorption intensities and the contents of the two-dimensional spectral analysis between NIR and mid-infrared spectral information. Proteinic nitrogen content in the dry leaf model was well predicted using the MEMS FT-NIR spectroscopic method. Additionally, nitrate nitrogen in the dry leaf model was also determined by the provided method, but the necessity of adding the data for a wider range of nitric acid concentrations was experimentally indicated for the prediction of nitrate nitrogen content in the wet leaf model. Consequently, these results experimentally suggest the possibility of the application of the compact MEMS FT-NIR for obtaining the bioinformation of crops at agricultural on-sites. [ABSTRACT FROM AUTHOR]

Engine oil oxidation is one of the major reasons for oil aging which can result in variations in the physical and chemical properties of oil. Organic acids generated by oil oxidation can react with water to form inorganic acids and acidic substances (including organic and inorganic acids) that corrode engine parts, resulting in the generation of rust or damage to engine parts. This is one of the important reasons why oil should be regularly changed. One of the most commonly applied methods for judging the aging degree of engine oil is monitoring its acid number (AN). However, generally, the effect of oil water content on acid value measurement is not considered. When oils are used in engines, they are often contaminated by water due to condensation, which accelerates engine oil aging. Therefore, it is crucial to explore the water content effect on AN in the process of engine oil aging. In this research, a water content sensor was applied to characterize moisture content in oxidized oil samples. The sensor could also obtain oil sample electrical conductivity which corresponded to its dielectric constant. Using a mid-infrared spectrometer to measure oil sample AN at this point to obtain the variation in AN with oxidation time, oil sample AN was connected in series with the water content, dielectric constant and electrical conductivity. These parameters were monitored through sensors, and the effect of water content on AN was studied. Experimental results revealed that with the increase in oxidation time, the water content, electrical conductivity, dielectric constant increase and AN of oil were increased. At the same time, since the temperature had a greater effect on electrical conductivity, the application of an air-conditioned constant-temperature environment removed the effect of temperature change on electrical conductivity. [ABSTRACT FROM AUTHOR]

Brain stroke, or a cerebrovascular accident, is a devastating medical condition that disrupts the blood supply to the brain, depriving it of oxygen and nutrients. Each year, according to the World Health Organization, 15 million people worldwide experience a stroke. This results in approximately 5 million deaths and another 5 million individuals suffering permanent disabilities. The complex interplay of various risk factors highlights the urgent need for sophisticated analytical methods to more accurately predict stroke risks and manage their outcomes. Machine learning and deep learning technologies offer promising solutions by analyzing extensive datasets including patient demographics, health records, and lifestyle choices to uncover patterns and predictors not easily discernible by humans. These technologies enable advanced data processing, analysis, and fusion techniques for a comprehensive health assessment. We conducted a comprehensive review of 25 review papers published between 2020 and 2024 on machine learning and deep learning applications in brain stroke diagnosis, focusing on classification, segmentation, and object detection. Furthermore, all these reviews explore the performance evaluation and validation of advanced sensor systems in these areas, enhancing predictive health monitoring and personalized care recommendations. Moreover, we also provide a collection of the most relevant datasets used in brain stroke analysis. The selection of the papers was conducted according to PRISMA guidelines. Furthermore, this review critically examines each domain, identifies current challenges, and proposes future research directions, emphasizing the potential of AI methods in transforming health monitoring and patient care. [ABSTRACT FROM AUTHOR]

Sensor data fusion analysis is a crucial process that integrates data from multiple sensors to provide more accurate and comprehensive information. This analysis has various applications in fields such as industry, medicine, robotics, transportation, and information systems. The article highlights sixteen high-quality papers that explore different aspects of sensor data fusion, including facial detection, object detection, odometry systems, geospatial data evaluation, and fault detection. The papers demonstrate the potential of sensor data fusion in improving decision-making, efficiency, and productivity in various industries. Future research in this area will focus on miniaturization, multi-sensor systems, and addressing challenges related to data quality in mobile sensors. [Extracted from the article]

Railway transportation has been integrated into people's lives. According to the "Notice on the release of the General Technical Specification of High-speed Railway Power Supply Safety Testing (6C System) System" issued by the National Railway Administration of China in 2012, it is required to install pantograph and slide monitoring devices in high-speed railway stations, station throats and the inlet and exit lines of high-speed railway sections, and it is required to detect the damage of the slider with high precision. It can be seen that the good condition of the pantograph slider is very important for the normal operation of the railway system. As a part of providing power for high-speed rail and subway, the pantograph must be paid attention to in railway transportation to ensure its integrity. The wear of the pantograph is mainly due to the contact power supply between the slide block and the long wire during high-speed operation, which inevitably produces scratches, resulting in depressions on the upper surface of the pantograph slide block. During long-term use, because the depression is too deep, there is a risk of fracture. Therefore, it is necessary to monitor the slider regularly and replace the slider with serious wear. At present, most of the traditional methods use automation technology or simple computer vision technology for detection, which is inefficient. Therefore, this paper introduces computer vision and deep learning technology into pantograph slide wear detection. Specifically, this paper mainly studies the wear detection of the pantograph slider based on deep learning and the main purpose is to improve the detection accuracy and improve the effect of segmentation. From a methodological perspective, this paper employs a linear array camera to enhance the quality of the data sets. Additionally, it integrates an attention mechanism to improve segmentation performance. Furthermore, this study introduces a novel image stitching method to address issues related to incomplete images, thereby providing a comprehensive solution. [ABSTRACT FROM AUTHOR]

The paper "Using Absorption Models for Insulin and Carbohydrates and Deep Leaning to Improve Glucose Level Predictions" (Sensors 2021, 21, 5273) proposes a novel approach to predicting blood glucose levels for people with type 1 diabetes mellitus (T1DM). By building exponential models from raw carbohydrate and insulin data to simulate the absorption in the body, the authors reported a reduction in their model's root-mean-square error (RMSE) from 15.5 mg/dL (raw) to 9.2 mg/dL (exponential) when predicting blood glucose levels one hour into the future. In this comment, we demonstrate that the experimental techniques used in that paper are flawed, which invalidates its results and conclusions. Specifically, after reviewing the authors' code, we found that the model validation scheme was malformed, namely, the training and test data from the same time intervals were mixed. This means that the reported RMSE numbers in the referenced paper did not accurately measure the predictive capabilities of the approaches that were presented. We repaired the measurement technique by appropriately isolating the training and test data, and we discovered that their models actually performed dramatically worse than was reported in the paper. In fact, the models presented in the that paper do not appear to perform any better than a naive model that predicts future glucose levels to be the same as the current ones. [ABSTRACT FROM AUTHOR]

Millimeter-wave radar-based identification technology has a wide range of applications in persistent identity verification, covering areas such as security production, healthcare, and personalized smart consumption systems. It has received extensive attention from the academic community due to its advantages of being non-invasive, environmentally insensitive and privacy-preserving. Existing identification algorithms mainly rely on a single signal, such as breathing or heartbeat. The reliability and accuracy of these algorithms are limited due to the high similarity of breathing patterns and the low signal-to-noise ratio of heartbeat signals. To address the above issues, this paper proposes an algorithm for multimodal fusion for identity recognition. This algorithm extracts and fuses features derived from phase signals, respiratory signals, and heartbeat signals for identity recognition purposes. The spatial features of signals with different modes are first extracted by the residual network (ResNet), after which these features are fused with a spatial-channel attention fusion module. On this basis, the temporal features are further extracted with a time series-based self-attention mechanism. Finally, the feature vectors of the user's vital sign modality are obtained to perform identity recognition. This method makes full use of the correlation and complementarity between different modal signals to improve the accuracy and reliability of identification. Simulation experiments show that the algorithm identity recognition proposed in this paper achieves an accuracy of 94.26% on a 20-subject self-test dataset, which is much higher than that of the traditional algorithm, which is about 85%. [ABSTRACT FROM AUTHOR]

In this paper, we propose a novel method for monocular depth estimation using the hourglass neck module. The proposed method has the following originality. First, feature maps are extracted from Swin Transformer V2 using a masked image modeling (MIM) pretrained model. Since Swin Transformer V2 has a different patch size for each attention stage, it is easier to extract local and global features from images input by the vision transformer (ViT)-based encoder. Second, to maintain the polymorphism and local inductive bias of the feature map extracted from Swin Transformer V2, a feature map is input into the hourglass neck module. Third, deformable attention can be used at the waist of the hourglass neck module to reduce the computation cost and highlight the locality of the feature map. Finally, the feature map traverses the neck and proceeds through a decoder, comprised of a deconvolution layer and an upsampling layer, to generate a depth image. To evaluate the objective reliability of the proposed method in this paper, we used the NYU Depth V2 dataset to compare and evaluate the methods published in other papers. As a result of the experiment, the RMSE value of the novel method for monocular depth estimation using the hourglass neck module proposed in this paper was 0.274, which was lower than those published in other papers. The lower the RMSE value, the better the depth estimation method; therefore, its efficiency compared to other techniques has been proven. [ABSTRACT FROM AUTHOR]

Hand-gripping training is important for improving the fundamental functions of human physical activity. Bernstein's idea of "repetition without repetition" suggests that motor control function should be trained under changing states. The randomness level of load should be visualized for self-administered screening when repeating various training tasks under changing states. This study aims to develop a sensing methodology of random loads applied to both the agonist and antagonist skeletal muscles when performing physical tasks. We assumed that the time-variability and periodicity of the applied load appear in the time-series feature of muscle deformation data. In the experiment, 14 participants conducted the gripping tasks with a gripper, ball, balloon, Palm clenching, and paper. Crumpling pieces of paper (paper exercise) involves randomness because the resistance force of the paper changes depending on the shape and layers of the paper. Optical myography during gripping tasks was measured, and time-series features were analyzed. As a result, our system could detect the random movement of muscles during training. [ABSTRACT FROM AUTHOR]

This document is a summary of a special issue on the topic of the integration of blockchain and Internet of Things (IoT) technologies. The special issue includes 11 papers that explore various applications and challenges related to this integration. The papers cover topics such as blockchain applications in cultural heritage preservation, energy trading, educational record-keeping, and collaborative manufacturing. Additionally, the papers discuss smart contract security and vulnerability detection, security and privacy in blockchain technology, and the integration of blockchain in wireless networks. Overall, the papers contribute innovative ideas and methodologies that have the potential to enhance the security, privacy, and efficiency of IoT-enabled blockchain ecosystems. [Extracted from the article]

The text describes the organization of a Special Issue in the Sensors journal titled "Recent Trends and Advances in Telecommunications and Sensing." The Special Issue was based on papers presented at the 17th International Conference on Telecommunications (ConTEL) held at Graz University of Technology in Austria. The conference covered various topics related to telecommunications, including optical communications, satellite communications, IoT, and security. Nine papers were accepted for publication in the Special Issue, covering subjects such as network experimentation, optical camera communications in healthcare, and anomaly detection in firewall logs. The authors of the text are Erich Leitgeb, Maja Matijašević, Wilfried Gappmair, and Mario Kušek. [Extracted from the article]

The precise segmentation of retinal vasculature is crucial for the early screening of various eye diseases, such as diabetic retinopathy and hypertensive retinopathy. Given the complex and variable overall structure of retinal vessels and their delicate, minute local features, the accurate extraction of fine vessels and edge pixels remains a technical challenge in the current research. To enhance the ability to extract thin vessels, this paper incorporates a pyramid channel attention module into a U-shaped network. This allows for more effective capture of information at different levels and increased attention to vessel-related channels, thereby improving model performance. Simultaneously, to prevent overfitting, this paper optimizes the standard convolutional block in the U-Net with the pre-activated residual discard convolution block, thus improving the model's generalization ability. The model is evaluated on three benchmark retinal datasets: DRIVE, CHASE_DB1, and STARE. Experimental results demonstrate that, compared to the baseline model, the proposed model achieves improvements in sensitivity (Sen) scores of 7.12%, 9.65%, and 5.36% on these three datasets, respectively, proving its strong ability to extract fine vessels. [ABSTRACT FROM AUTHOR]

Internet of Things (IoT) technology has become an inevitable part of our daily lives. With the increase in usage of IoT Devices, manufacturers continuously develop IoT technology. However, the security of IoT devices is left behind in those developments due to cost, size, and computational power limitations. Since these IoT devices are connected to the Internet and have low security levels, one of the main risks of these devices is being compromised by malicious malware and becoming part of IoT botnets. IoT botnets are used for launching different types of large-scale attacks including Distributed Denial-of-Service (DDoS) attacks. These attacks are continuously evolving, and researchers have conducted numerous analyses and studies in this area to narrow security vulnerabilities. This paper systematically reviews the prominent literature on IoT botnet DDoS attacks and detection techniques. Architecture IoT botnet DDoS attacks, evaluations of those attacks, and systematically categorized detection techniques are discussed in detail. The paper presents current threats and detection techniques, and some open research questions are recommended for future studies in this field. [ABSTRACT FROM AUTHOR]

In answer to the demand for high sensitivity and miniaturization of ultra-high frequency (UHF) sensors for partial discharge (PD) detection in power equipment, this paper proposes research on miniaturized UHF-sensing technology for PD detection in power equipment based on symmetric cut theory. The symmetric cut theory is applied for the first time to the miniaturization of PD UHF sensors for power equipment. A planar monopole UHF sensor with a size of only 70 mm × 70 mm × 1.6 mm is developed using an exponential asymptotic feed line approach, which is a 50% size reduction. The frequency–response characteristics of the sensor are simulated, optimized and tested; the results show that the standing wave ratio of the sensor developed in this paper is less than 2 in the frequency band from 427 MHz to 1.54 GHz, and less than 5 in the frequency band from 300 MHz to 1.95 GHz; in the 300 MHz~1.5 GHz band; the maximum and average gains of the sensor E-plane are 4.76 dB and 1.02 dB, respectively. Finally, the PD simulation experiment platform for power equipment is built to test the sensor's sensing performance; the results show that the sensor can effectively detect the PD signals; the sensing sensitivity is improved by about 95% relative to an elliptical monopole UHF sensor. [ABSTRACT FROM AUTHOR]

With the development of biometric identification technology, finger vein identification has received more and more widespread attention for its security, efficiency, and stability. However, because of the performance of the current standard finger vein image acquisition device and the complex internal organization of the finger, the acquired images are often heavily degraded and have lost their texture characteristics. This makes the topology of the finger veins inconspicuous or even difficult to distinguish, greatly affecting the identification accuracy. Therefore, this paper proposes a finger vein image recovery and enhancement algorithm using atmospheric scattering theory. Firstly, to normalize the local over-bright and over-dark regions of finger vein images within a certain threshold, the Gamma transform method is improved in this paper to correct and measure the gray value of a given image. Then, we reconstruct the image based on atmospheric scattering theory and design a pixel mutation filter to segment the venous and non-venous contact zones. Finally, the degraded finger vein images are recovered and enhanced by global image gray value normalization. Experiments on SDUMLA-HMT and ZJ-UVM datasets show that our proposed method effectively achieves the recovery and enhancement of degraded finger vein images. The image restoration and enhancement algorithm proposed in this paper performs well in finger vein recognition using traditional methods, machine learning, and deep learning. The recognition accuracy of the processed image is improved by more than 10% compared to the original image. [ABSTRACT FROM AUTHOR]

Bibliometric analysis is a rigorous method to analyze significant quantities of bibliometric data to assess their impact on a particular field. This study used bibliometric analysis to investigate the academic research on diabetes detection and classification from 2000 to 2023. The PRISMA 2020 framework was followed to identify, filter, and select relevant papers. This study used the Web of Science database to determine relevant publications concerning diabetes detection and classification using the keywords "diabetes detection", "diabetes classification", and "diabetes detection and classification". A total of 863 publications were selected for analysis. The research applied two bibliometric techniques: performance analysis and science mapping. Various bibliometric parameters, including publication analysis, trend analysis, citation analysis, and networking analysis, were used to assess the performance of these articles. The analysis findings showed that India, China, and the United States are the top three countries with the highest number of publications and citations on diabetes detection and classification. The most frequently used keywords are machine learning, diabetic retinopathy, and deep learning. Additionally, the study identified "classification", "diagnosis", and "validation" as the prevailing topics for diabetes identification. This research contributes valuable insights into the academic landscape of diabetes detection and classification. [ABSTRACT FROM AUTHOR]

In the Energy-Harvesting (EH) Cognitive Internet of Things (EH-CIoT) network, due to the broadcast nature of wireless communication, the EH-CIoT network is susceptible to jamming attacks, which leads to a serious decrease in throughput. Therefore, this paper investigates an anti-jamming resource-allocation method, aiming to maximize the Long-Term Throughput (LTT) of the EH-CIoT network. Specifically, the resource-allocation problem is modeled as a Markov Decision Process (MDP) without prior knowledge. On this basis, this paper carefully designs a two-dimensional reward function that includes throughput and energy rewards. On the one hand, the Agent Base Station (ABS) intuitively evaluates the effectiveness of its actions through throughput rewards to maximize the LTT. On the other hand, considering the EH characteristics and battery capacity limitations, this paper proposes energy rewards to guide the ABS to reasonably allocate channels for Secondary Users (SUs) with insufficient power to harvest more energy for transmission, which can indirectly improve the LTT. In the case where the activity states of Primary Users (PUs), channel information and the jamming strategies of the jammer are not available in advance, this paper proposes a Linearly Weighted Deep Deterministic Policy Gradient (LWDDPG) algorithm to maximize the LTT. The LWDDPG is extended from DDPG to adapt to the design of the two-dimensional reward function, which enables the ABS to reasonably allocate transmission channels, continuous power and work modes to the SUs, and to let the SUs not only transmit on unjammed channels, but also harvest more RF energy to supplement the battery power. Finally, the simulation results demonstrate the validity and superiority of the proposed method compared with traditional methods under multiple jamming attacks. [ABSTRACT FROM AUTHOR]

To achieve Level 4 and above autonomous driving, a robust and stable autonomous driving system is essential to adapt to various environmental changes. This paper aims to perform vehicle pose estimation, a crucial element in forming autonomous driving systems, more universally and robustly. The prevalent method for vehicle pose estimation in autonomous driving systems relies on Real-Time Kinematic (RTK) sensor data, ensuring accurate location acquisition. However, due to the characteristics of RTK sensors, precise positioning is challenging or impossible in indoor spaces or areas with signal interference, leading to inaccurate pose estimation and hindering autonomous driving in such scenarios. This paper proposes a method to overcome these challenges by leveraging objects registered in a high-precision map. The proposed approach involves creating a semantic high-definition (HD) map with added objects, forming object-centric features, recognizing locations using these features, and accurately estimating the vehicle's pose from the recognized location. This proposed method enhances the precision of vehicle pose estimation in environments where acquiring RTK sensor data is challenging, enabling more robust and stable autonomous driving. The paper demonstrates the proposed method's effectiveness through simulation and real-world experiments, showcasing its capability for more precise pose estimation. [ABSTRACT FROM AUTHOR]

With the rapid development of sensors and other devices, precise control for the generation of new energy, especially in the context of highly stochastic wind power generation, has been strongly supported. However, large-scale wind farm grid connection can cause the power system to enter a low inertia state, leading to frequency instability. Battery energy storage systems (BESSs) have the advantages of a fast response speed and high flexibility, and can be applied to wind farm systems to improve the frequency fluctuation problem in the process of grid connection. To address the frequency fluctuation problem caused by the parameter error of the fuzzy membership function in the fuzzy control of a doubly fed induction generator (DFIG) and a BESS, this paper proposes an improved Artificial Bee Colony (ABC) algorithm based on multi-source sensor data for optimizing the fuzzy controller to improve the frequency control ability of BESSs and DFIGs. A Gaussian wandering mechanism was introduced to improve the ABC algorithm and enhance the convergence speed of the algorithm, and the improved ABC algorithm was optimized for the selection of fuzzy control affiliation function parameters to improve the frequency response performance. The effectiveness of the proposed control strategy was verified on the MATLAB/Simulink simulation platform. After optimization using the proposed control strategy, the oscillation amplitude was reduced by 0.15 Hz, the precision was increased by 40%, and the steady-state frequency deviation was reduced by 26%. The results show that the method proposed in this paper provides a great improvement in the frequency stability of coordinated systems of wind farms and BESSs. [ABSTRACT FROM AUTHOR]

This document discusses the advancements in deep learning technology and image sensing. It highlights the role of deep learning in improving image recognition data and sensor performance in various applications, such as autonomous driving and smartphone camera functionalities. The document presents eleven papers published in a special issue on deep learning technology and image sensing, covering topics like medical imaging, image enhancement, object detection, and innovation in image sensing technologies. The papers demonstrate innovative approaches and methodologies in diverse domains, including liver segmentation, brain tumor classification, optic cup and disc edge detection, image-to-image translation in astronomy, super-resolution imaging, and object detection systems. These studies contribute to the interdisciplinary field of deep learning-based imaging and sensing and offer valuable insights for various fields, including healthcare, astronomy, and robotics. [Extracted from the article]

Semantic segmentation of target objects in power transmission line corridor point cloud scenes is a crucial step in powerline tree barrier detection. The massive quantity, disordered distribution, and non-uniformity of point clouds in power transmission line corridor scenes pose significant challenges for feature extraction. Previous studies have often overlooked the core utilization of spatial information, limiting the network's ability to understand complex geometric shapes. To overcome this limitation, this paper focuses on enhancing the deep expression of spatial geometric information in segmentation networks and proposes a method called BDF-Net to improve RandLA-Net. For each input 3D point cloud data, BDF-Net first encodes the relative coordinates and relative distance information into spatial geometric feature representations through the Spatial Information Encoding block to capture the local spatial structure of the point cloud data. Subsequently, the Bilinear Pooling block effectively combines the feature information of the point cloud with the spatial geometric representation by leveraging its bilinear interaction capability thus learning more discriminative local feature descriptors. The Global Feature Extraction block captures the global structure information in the point cloud data by using the ratio between the point position and the relative position, so as to enhance the semantic understanding ability of the network. In order to verify the performance of BDF-Net, this paper constructs a dataset, PPCD, for the point cloud scenario of transmission line corridors and conducts detailed experiments on it. The experimental results show that BDF-Net achieves significant performance improvements in various evaluation metrics, specifically achieving an OA of 97.16%, a mIoU of 77.48%, and a mAcc of 87.6%, which are 3.03%, 16.23%, and 18.44% higher than RandLA-Net, respectively. Moreover, comparisons with other state-of-the-art methods also verify the superiority of BDF-Net in point cloud semantic segmentation tasks. [ABSTRACT FROM AUTHOR]

As an indispensable part of the vehicle environment perception task, road traffic marking detection plays a vital role in correctly understanding the current traffic situation. However, the existing traffic marking detection algorithms still have some limitations. Taking lane detection as an example, the current detection methods mainly focus on the location information detection of lane lines, and they only judge the overall attribute of each detected lane line instance, thus lacking more fine-grained dynamic detection of lane line attributes. In order to meet the needs of intelligent vehicles for the dynamic attribute detection of lane lines and more perfect road environment information in urban road environment, this paper constructs a fine-grained attribute detection method for lane lines, which uses pixel-level attribute sequence points to describe the complete attribute distribution of lane lines and then matches the detection results of the lane lines. Realizing the attribute judgment of different segment positions of lane instances is called the fine-grained attribute detection of lane lines (Lane-FGA). In addition, in view of the lack of annotation information in the current open-source lane data set, this paper constructs a lane data set with both lane instance information and fine-grained attribute information by combining manual annotation and intelligent annotation. At the same time, a cyclic iterative attribute inference algorithm is designed to solve the difficult problem of lane attribute labeling in areas without visual cues such as occlusion and damage. In the end, the average accuracy of the proposed algorithm reaches 97% on various types of lane attribute detection. [ABSTRACT FROM AUTHOR]

Establishing an accurate and robust feature fusion mechanism is key to enhancing the tracking performance of single-object trackers based on a Siamese network. However, the output features of the depth-wise cross-correlation feature fusion module in fully convolutional trackers based on Siamese networks cannot establish global dependencies on the feature maps of a search area. This paper proposes a dynamic cascade feature fusion (DCFF) module by introducing a local feature guidance (LFG) module and dynamic attention modules (DAMs) after the depth-wise cross-correlation module to enhance the global dependency modeling capability during the feature fusion process. In this paper, a set of verification experiments is designed to investigate whether establishing global dependencies for the features output by the depth-wise cross-correlation operation can significantly improve the performance of fully convolutional trackers based on a Siamese network, providing experimental support for rational design of the structure of a dynamic cascade feature fusion module. Secondly, we integrate the dynamic cascade feature fusion module into the tracking framework based on a Siamese network, propose SiamDCFF, and evaluate it using public datasets. Compared with the baseline model, SiamDCFF demonstrated significant improvements. [ABSTRACT FROM AUTHOR]

Virtual reality (VR) driving simulators are very promising tools for driver assessment since they provide a controlled and adaptable setting for behavior analysis. At the same time, wearable sensor technology provides a well-suited and valuable approach to evaluating the behavior of drivers and their physiological or psychological state. This review paper investigates the potential of wearable sensors in VR driving simulators. Methods: A literature search was performed on four databases (Scopus, Web of Science, Science Direct, and IEEE Xplore) using appropriate search terms to retrieve scientific articles from a period of eleven years, from 2013 to 2023. Results: After removing duplicates and irrelevant papers, 44 studies were selected for analysis. Some important aspects were extracted and presented: the number of publications per year, countries of publication, the source of publications, study aims, characteristics of the participants, and types of wearable sensors. Moreover, an analysis and discussion of different aspects are provided. To improve car simulators that use virtual reality technologies and boost the effectiveness of particular driver training programs, data from the studies included in this systematic review and those scheduled for the upcoming years may be of interest. [ABSTRACT FROM AUTHOR]

Buildings are complex structures composed of heterogeneous elements; these require building management systems (BMSs) to dynamically adapt them to occupants' needs and leverage building resources. The fast growth of information and communication technologies (ICTs) has transformed the BMS field into a multidisciplinary one. Consequently, this has caused several research papers on data-driven solutions to require examination and classification. This paper provides a broad overview of BMS by conducting a systematic literature review (SLR) summarizing current trends in this field. Unlike similar reviews, this SLR provides a rigorous methodology to review current research from a computer science perspective. Therefore, our goal is four-fold: (i) Identify the main topics in the field of building; (ii) Identify the recent data-driven methods; (iii) Understand the BMS's underlying computing architecture (iv) Understand the features of BMS that contribute to the smartization of buildings. The result synthesizes our findings and provides research directions for further research. [ABSTRACT FROM AUTHOR]

The types of obstacles encountered in the road environment are complex and diverse, and accurate and reliable detection of obstacles is the key to improving traffic safety. Traditional obstacle detection methods are limited by the type of samples and therefore cannot detect others comprehensively. Therefore, this paper proposes an obstacle detection method based on longitudinal active vision. The obstacles are recognized according to the height difference characteristics between the obstacle imaging points and the ground points in the image, and the obstacle detection in the target area is realized without accurately distinguishing the obstacle categories, which reduces the spatial and temporal complexity of the road environment perception. The method of this paper is compared and analyzed with the obstacle detection methods based on VIDAR (vision-IMU based detection and range method), VIDAR + MSER, and YOLOv8s. The experimental results show that the method in this paper has high detection accuracy and verifies the feasibility of obstacle detection in road environments where unknown obstacles exist. [ABSTRACT FROM AUTHOR]

The efficient and accurate identification of traffic signs is crucial to the safety and reliability of active driving assistance and driverless vehicles. However, the accurate detection of traffic signs under extreme cases remains challenging. Aiming at the problems of missing detection and false detection in traffic sign recognition in fog traffic scenes, this paper proposes a recognition algorithm for traffic signs based on pix2pixHD+YOLOv5-T. Firstly, the defogging model is generated by training the pix2pixHD network to meet the advanced visual task. Secondly, in order to better match the defogging algorithm with the target detection algorithm, the algorithm YOLOv5-Transformer is proposed by introducing a transformer module into the backbone of YOLOv5. Finally, the defogging algorithm pix2pixHD is combined with the improved YOLOv5 detection algorithm to complete the recognition of traffic signs in foggy environments. Comparative experiments proved that the traffic sign recognition algorithm proposed in this paper can effectively reduce the impact of a foggy environment on traffic sign recognition. Compared with the YOLOv5-T and YOLOv5 algorithms in moderate fog environments, the overall improvement of this algorithm is achieved. The precision of traffic sign recognition of the algorithm in the fog traffic scene reached 78.5%, the recall rate was 72.2%, and mAP@0.5 was 82.8%. [ABSTRACT FROM AUTHOR]

Mechanical equipment is composed of several parts, and the interaction between parts exists throughout the whole life cycle, leading to the widespread phenomenon of fault coupling. The diagnosis of independent faults cannot meet the requirements of the health management of mechanical equipment under actual working conditions. In this paper, the dynamic vertex interpretable graph neural network (DIGNN) is proposed to solve the problem of coupling fault diagnosis, in which dynamic vertices are defined in the data topology. First, in the date preprocessing phase, wavelet transform is utilized to make input features interpretable and reduce the uncertainty of model training. In the fault topology, edge connections are made between nodes according to the fault coupling information, and edge connections are established between dynamic nodes and all other nodes. Second the data topology with dynamic vertices is used in the training phase and in the testing phase, the time series data are only fed into dynamic vertices for classification and analysis, which makes it possible to realize coupling fault diagnosis in an industrial production environment. The features extracted in different layers of DIGNN interpret how the model works. The method proposed in this paper can realize the accurate diagnosis of independent faults in the dataset with an accuracy of 100%, and can effectively judge the coupling mode of coupling faults with a comprehensive accuracy of 88.3%. [ABSTRACT FROM AUTHOR]

This paper proposes a solution to the problem of mobile robot navigation and trajectory interpolation in dynamic environments with large scenes. The solution combines a semantic laser SLAM system that utilizes deep learning and a trajectory interpolation algorithm. The paper first introduces some open-source laser SLAM algorithms and then elaborates in detail on the general framework of the SLAM system used in this paper. Second, the concept of voxels is introduced into the occupation probability map to enhance the ability of local voxel maps to represent dynamic objects. Then, in this paper, we propose a PointNet++ point cloud semantic segmentation network combined with deep learning algorithms to extract deep features of dynamic point clouds in large scenes and output semantic information of points on static objects. A descriptor of the global environment is generated based on its semantic information. Closed-loop completion of global map optimization is performed to reduce cumulative error. Finally, T-trajectory interpolation is utilized to ensure the motion performance of the robot and improve the smooth stability of the robot trajectory. The experimental results indicate that the combination of the semantic laser SLAM system with deep learning and the trajectory interpolation algorithm proposed in this paper yields better graph-building and loop-closure effects in large scenes at SIASUN large scene campus. The use of T-trajectory interpolation ensures vibration-free and stable transitions between target points. [ABSTRACT FROM AUTHOR]

Aiming at the problem that traditional wireless sensor networks produce errors in the positioning and tracking of motorised targets due to noise interference, this paper proposes a motorised target tracking method with a convolutional bi-directional long and short-term memory neural network and extended Kalman filtering, which is trained by using the simulated RSSI value and the actual target value of motorised targets collected from the convolutional bi-directional neural network to the sensor anchor node, so as to obtain a more accurate initial value of the manoeuvre target, and at the same time, the extended Kalman filtering method is used to accurately locate and track the real-time target, so as to obtain the accurate positioning and tracking information of the real-time target. Through experimental simulation, it can be seen that the algorithm proposed in this paper has good tracking effect in both linear manoeuvre target tracking scenarios and non-linear manoeuvre target tracking scenarios. [ABSTRACT FROM AUTHOR]

In complex environments a single visible image is not good enough to perceive the environment, this paper proposes a novel dual-stream real-time detector designed for target detection in extreme environments such as nighttime and fog, which is able to efficiently utilise both visible and infrared images to achieve Fast All-Weatherenvironment sensing (FAWDet). Firstly, in order to allow the network to process information from different modalities simultaneously, this paper expands the state-of-the-art end-to-end detector YOLOv8, the backbone is expanded in parallel as a dual stream. Then, for purpose of avoid information loss in the process of network deepening, a cross-modal feature enhancement module is designed in this study, which enhances each modal feature by cross-modal attention mechanisms, thus effectively avoiding information loss and improving the detection capability of small targets. In addition, for the significant differences between modal features, this paper proposes a three-stage fusion strategy to optimise the feature integration through the fusion of spatial, channel and overall dimensions. It is worth mentioning that the cross-modal feature fusion module adopts an end-to-end training approach. Extensive experiments on two datasets validate that the proposed method achieves state-of-the-art performance in detecting small targets. The cross-modal real-time detector in this study not only demonstrates excellent stability and robust detection performance, but also provides a new solution for target detection techniques in extreme environments. [ABSTRACT FROM AUTHOR]

In today's world, a significant amount of global energy is used in buildings. Unfortunately, a lot of this energy is wasted, because electrical appliances are not used properly or efficiently. One way to reduce this waste is by detecting, learning, and predicting when people are present in buildings. To do this, buildings need to become "smart" and "cognitive" and use modern technologies to sense when and how people are occupying the buildings. By leveraging this information, buildings can make smart decisions based on recently developed methods. In this paper, we provide a comprehensive overview of recent advancements in Internet of Things (IoT) technologies that have been designed and used for the monitoring of indoor environmental conditions within buildings. Using these technologies is crucial to gathering data about the indoor environment and determining the number and presence of occupants. Furthermore, this paper critically examines both the strengths and limitations of each technology in predicting occupant behavior. In addition, it explores different methods for processing these data and making future occupancy predictions. Moreover, we highlight some challenges, such as determining the optimal number and location of sensors and radars, and provide a detailed explanation and insights into these challenges. Furthermore, the paper explores possible future directions, including the security of occupants' data and the promotion of energy-efficient practices such as localizing occupants and monitoring their activities within a building. With respect to other survey works on similar topics, our work aims to both cover recent sensory approaches and review methods used in the literature for estimating occupancy. [ABSTRACT FROM AUTHOR]

In response to the challenges posed by small objects in remote sensing images, such as low resolution, complex backgrounds, and severe occlusions, this paper proposes a lightweight improved model based on YOLOv8n. During the detection of small objects, the feature fusion part of the YOLOv8n algorithm retrieves relatively fewer features of small objects from the backbone network compared to large objects, resulting in low detection accuracy for small objects. To address this issue, firstly, this paper adds a dedicated small object detection layer in the feature fusion network to better integrate the features of small objects into the feature fusion part of the model. Secondly, the SSFF module is introduced to facilitate multi-scale feature fusion, enabling the model to capture more gradient paths and further improve accuracy while reducing model parameters. Finally, the HPANet structure is proposed, replacing the Path Aggregation Network with HPANet. Compared to the original YOLOv8n algorithm, the recognition accuracy of mAP@0.5 on the VisDrone data set and the AI-TOD data set has increased by 14.3% and 17.9%, respectively, while the recognition accuracy of mAP@0.5:0.95 has increased by 17.1% and 19.8%, respectively. The proposed method reduces the parameter count by 33% and the model size by 31.7% compared to the original model. Experimental results demonstrate that the proposed method can quickly and accurately identify small objects in complex backgrounds. [ABSTRACT FROM AUTHOR]

Track smoothness has become an important factor in the safe operation of high-speed trains. In order to ensure the safety of high-speed operations, studies on track smoothness detection methods are constantly improving. This paper presents a track irregularity identification method based on CNN-Bi-LSTM and predicts track irregularity through car body acceleration detection, which is easy to collect and can be obtained by passenger trains, so the model proposed in this paper provides an idea for the development of track irregularity identification method based on conventional vehicles. The first step is construction of the data set required for model training. The model input is the car body acceleration detection sequence, and the output is the irregularity sequence of the same length. The fluctuation trend of the irregularity data is extracted by the HP filtering (Hodrick Prescott Filter) algorithm as the prediction target. The second is a prediction model based on the CNN-Bi-LSTM network, extracting features from the car body acceleration data and realizing the point-by-point prediction of irregularities. Meanwhile, this paper proposes an exponential weighted mean square error with priority inner fitting (EIF-MSE) as the loss function, improving the accuracy of big value data prediction, and reducing the risk of false alarms. In conclusion, the model is verified based on the simulation data and the real data measured by the high-speed railway comprehensive inspection train. [ABSTRACT FROM AUTHOR]

The rapid increase in the number of vehicles has led to increasing traffic congestion, traffic accidents, and motor vehicle crime rates. The management of various parking lots has also become increasingly challenging. Vehicle-type recognition technology can reduce the workload of humans in vehicle management operations. Therefore, the application of image technology for vehicle-type recognition is of great significance for integrated traffic management. In this paper, an improved faster region with convolutional neural network features (Faster R-CNN) model was proposed for vehicle-type recognition. Firstly, the output features of different convolution layers were combined to improve the recognition accuracy. Then, the average precision (AP) of the recognition model was improved through the contextual features of the original image and the object bounding box optimization strategy. Finally, the comparison experiment used the vehicle image dataset of three vehicle types, including cars, sports utility vehicles (SUVs), and vans. The experimental results show that the improved recognition model can effectively identify vehicle types in the images. The AP of the three vehicle types is 83.2%, 79.2%, and 78.4%, respectively, and the mean average precision (mAP) is 1.7% higher than that of the traditional Faster R-CNN model. [ABSTRACT FROM AUTHOR]

In the context of Industry 4.0, industrial production equipment needs to communicate through the industrial internet to improve the intelligence of industrial production. This requires the current communication network to have the ability of large-scale equipment access, multiple communication protocols/heterogeneous systems interoperability, and end-to-end deterministic low-latency transmission. Time-sensitive network (TSN), as a new generation of deterministic Ethernet communication technology, is the main development direction of time-critical communication technology applied in industrial environments, and Wi-Fi technology has become the main way of wireless access for users due to its advantages of high portability and mobility. Therefore, accessing WiFi in the TSN is a major development direction of the current industrial internet. In this paper, we model the scheduling problem of TSN and WiFi converged networks and propose a scheme based on a greedy strategy distributed estimation algorithm (GE) to solve the scheduling problem. Compared with the integer linear programming (ILP) algorithm and the Tabu algorithm, the algorithm implemented in this paper outperforms the other algorithms in being able to adapt to a variety of different scenarios and in scheduling optimization efficiency, especially when the amount of traffic to be deployed is large. [ABSTRACT FROM AUTHOR]

The Internet of Things (IoT) includes billions of sensors and actuators (which we refer to as IoT devices) that harvest data from the physical world and send it via the Internet to IoT applications to provide smart IoT services and products. Deploying, managing, and maintaining IoT devices for the exclusive use of an individual IoT application is inefficient and involves significant costs and effort that often outweigh the benefits. On the other hand, enabling large numbers of IoT applications to share available third-party IoT devices, which are deployed and maintained independently by a variety of IoT device providers, reduces IoT application development costs, time, and effort. To achieve a positive cost/benefit ratio, there is a need to support the sharing of third-party IoT devices globally by providing effective IoT device discovery, use, and pay between IoT applications and third-party IoT devices. A solution for global IoT device sharing must be the following: (1) scalable to support a vast number of third-party IoT devices, (2) interoperable to deal with the heterogeneity of IoT devices and their data, and (3) IoT-owned, i.e., not owned by a specific individual or organization. This paper surveys existing techniques that support discovering, using, and paying for third-party IoT devices. To ensure that this survey is comprehensive, this paper presents our methodology, which is inspired by Systematic Literature Network Analysis (SLNA), combining the Systematic Literature Review (SLR) methodology with Citation Network Analysis (CNA). Finally, this paper outlines the research gaps and directions for novel research to realize global IoT device sharing. [ABSTRACT FROM AUTHOR]

The Internet of Things (IoT) is what we have as a great breakthrough in the 5G network. Although the 5G network can support several Internet of Everything (IoE) services, 6G is the network to fully support that. This paper is a survey research presenting the 5G and IoT technology and the challenges coming, with the 6G network being the new alternative network coming to solve these issues and limitations we are facing with 5G. A reference to the Control Plane and User Plane Separation (CUPS) is made with IPv4 and IPv6, addressing which is the foundation of the network slicing for the 5G core network. In comparison to other related papers, we provide in-depth information on how the IoT is going to affect our lives and how this technology is handled as the IoE in the 6G network. Finally, a full reference is made to the 6G network, with its challenges compared to the 5G network. [ABSTRACT FROM AUTHOR]

In recent years, the deformation detection technology for underground tunnels has played a crucial role in coal mine safety management. Currently, traditional methods such as the cross method and those employing the roof abscission layer monitoring instrument are primarily used for tunnel deformation detection in coal mines. With the advancement of photogrammetric methods, three-dimensional laser scanners have gradually become the primary method for deformation detection of coal mine tunnels. However, due to the high-risk confined spaces and distant distribution of coal mine tunnels, stationary three-dimensional laser scanning technology requires a significant amount of labor and time, posing certain operational risks. Currently, mobile laser scanning has become a popular method for coal mine tunnel deformation detection. This paper proposes a method for detecting point cloud deformation of underground coal mine tunnels based on a handheld three-dimensional laser scanner. This method utilizes SLAM laser radar to obtain complete point cloud information of the entire tunnel, while projecting the three-dimensional point cloud onto different planes to obtain the coordinates of the tunnel centerline. By using the calculated tunnel centerline, the three-dimensional point cloud data collected at different times are matched to the same coordinate system, and then the tunnel deformation parameters are analyzed separately from the global and cross-sectional perspectives. Through on-site collection of tunnel data, this paper verifies the feasibility of the algorithm and compares it with other centerline fitting and point cloud registration algorithms, demonstrating higher accuracy and meeting practical needs. [ABSTRACT FROM AUTHOR]

There have been many studies on the significant correlation between the hydrogen peroxide content of different tissues or cells in the human body and the risk of disease, so the preparation of biosensors for detecting hydrogen peroxide concentration has been a hot topic for researchers. In this paper, palladium nanoparticles (PdNPs) and laser-induced graphene (LIG) were prepared by liquid-phase pulsed laser ablation and laser-induced technology, respectively. The complexes were prepared by stirring and used for the modification of screen-printed electrodes to develop a non-enzymatic hydrogen peroxide biosensor that is low cost and mass preparable. The PdNPs prepared with anhydrous ethanol as a solvent have a uniform particle size distribution. The LIG prepared by laser direct writing has good electrical conductivity, and its loose porous structure provides more adsorption sites. The electrochemical properties of the modified electrode were characterized by cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy. Compared with bare screen-printed electrodes, the modified electrodes are more sensitive for the detection of hydrogen peroxide. The sensor has a linear response range of 5 µM–0.9 mM and 0.9 mM–5 mM. The limit of detection is 0.37 µM. The above conclusions indicate that the hydrogen peroxide electrochemical biosensor prepared in this paper has great advantages and potential in electrochemical catalysis. [ABSTRACT FROM AUTHOR]

Tool condition monitoring technology is an indispensable part of intelligent manufacturing. Most current research focuses on complex signal processing techniques or advanced deep learning algorithms to improve prediction performance without fully leveraging the end-to-end advantages of deep learning. The challenge lies in transforming multi-sensor raw data into input data suitable for direct model feeding, all while minimizing data scale and preserving sufficient temporal interpretation of tool wear. However, there is no clear reference standard for this so far. In light of this, this paper innovatively explores the processing methods that transform raw data into input data for deep learning models, a process known as an input paradigm. This paper introduces three new input paradigms: the downsampling paradigm, the periodic paradigm, and the subsequence paradigm. Then an improved hybrid model that combines a convolutional neural network (CNN) and bidirectional long short-term memory (BiLSTM) was employed to validate the model's performance. The subsequence paradigm demonstrated considerable superiority in prediction results based on the PHM2010 dataset, as the newly generated time series maintained the integrity of the raw data. Further investigation revealed that, with 120 subsequences and the temporal indicator being the maximum value, the model's mean absolute error (MAE) and root mean square error (RMSE) were the lowest after threefold cross-validation, outperforming several classical and contemporary methods. The methods explored in this paper provide references for designing input data for deep learning models, helping to enhance the end-to-end potential of deep learning models, and promoting the industrial deployment and practical application of tool condition monitoring systems. [ABSTRACT FROM AUTHOR]

In order to improve the reading efficiency of pointer meter, this paper proposes a reading method based on LinkNet. Firstly, the meter dial area is detected using YOLOv8. Subsequently, the detected images are fed into the improved LinkNet segmentation network. In this network, we replace traditional convolution with partial convolution, which reduces the number of model parameters while ensuring accuracy is not affected. Remove one pair of encoding and decoding modules to further compress the model size. In the feature fusion part of the model, the CBAM (Convolutional Block Attention Module) attention module is added and the direct summing operation is replaced by the AFF (Attention Feature Fusion) module, which enhances the feature extraction capability of the model for the segmented target. In the subsequent rotation correction section, this paper effectively addresses the issue of inaccurate prediction by CNN networks for axisymmetric images within the 0–360° range, by dividing the rotation angle prediction into classification and regression steps. It ensures that the final reading part receives the correct angle of image input, thereby improving the accuracy of the overall reading algorithm. The final experimental results indicate that our proposed reading method has a mean absolute error of 0.20 and a frame rate of 15. [ABSTRACT FROM AUTHOR]