Search

Abstract: Three different compositions of ZnO–In2O3 composite nanofibers were prepared by electrospinning, and their gas sensing characteristics were compared to those of pure ZnO and In2O3 nanofibers. All ZnO–In2O3 composite nanofibers showed high response to trimethylamine (TMA), relatively low cross-response to C2H5OH, and negligible cross-responses to CO and H2; pure ZnO or In2O3 nanofibers did not show selective detection of TMA. The maximum responses to 5ppm TMA of the ZnO–In2O3 composite nanofibers with the compositions of [Zn]:[In]=67:33, 50:50, and 33:67 by at% were 133.9 at 300°C, 82.9 at 350°C, and 119.4 at 375°C, respectively. Considering all the sensing characteristics such as gas response, selectivity, and sensing/recovering kinetics together, the operation of the ZnO–In2O3 nanofiber sensor with the composition of [Zn]:[In]=33:67 by at% at 375°C was determined to be in optimal condition to detect TMA. The significant enhancement of gas response and selectivity by the formation of composite nanofibers is discussed in relation to the variation of particle size, the formation of hetero-interfaces between ZnO and In2O3, and the combination of two sensing materials with different catalytic properties, gas adsorption behaviors, and acid–base properties. [Copyright &y& Elsevier]

Abstract: One-dimensional (1D) amorphous InGaZnO4 (a-IGZO) submicron-tubes were synthesized in a method involving an electrospun polymeric fiber template and the direct RF-sputter-coating of a-IGZO films combined with subsequent calcination at 450°C. The a-IGZO hollow fibers with a diameter of 300nm and a shell thickness of 20–30nm showed an amorphous structure, as confirmed by XRD and HR-TEM analyses. Gas sensors using semiconducting a-IGZO tube networks exhibited n-type gas sensing characteristics and a 3.7-fold higher gas response (R gas /R air =109.5 at 2ppm NO2) compared to (R gas /R air =29.4) planar a-IGZO thin films at an operating temperature of 300°C. The enhanced gas response of a-IGZO tubes is attributed to the greater space charge modulation depth associated with the thin shell structures and the porous networks which are readily accessible by gas. [Copyright &y& Elsevier]

In this work, a novel catalytic synthesis and functionalization method using apoferritin is used to fabricate RuO 2 nanoparticles (NPs) loaded WO 3 nanofibers (NFs) for potential diagnosis of diabetes. Catalytic ruthenium (Ru) NPs with very small average diameters of 1.8 ± 0.9 nm were synthesized using apoferritin which is a hollow protein cage, and were easily functionalized on WO 3 NFs by introducing electrospinning solution with W precursor and polyvinylpyrrolidone (PVP). As-spun Ru NPs-loaded W precursor/PVP composite NFs were calcined at 600 °C for 1 h in air atmosphere to achieve RuO 2 -functionalized WO 3 NFs. The small size and uniform distribution of catalytic RuO 2 NPs were well maintained due to hollow nature of apoferritin cages after calcination. The chemo-resistive sensors using RuO 2 -functionalized WO 3 NFs showed significantly enhanced acetone (CH 3 COCH 3 ) sensing response (R air /R gas = 78.61–5 ppm), which was 7.4 times higher than the response (R air /R gas = 10.61–5 ppm) of pristine WO 3 NFs at highly humid atmosphere (95% RH). In addition, the RuO 2 -functionalized WO 3 NFs showed outstanding selectivity toward acetone gas in comparison with other gases such as hydrogen sulfide (H 2 S), toluene (C 6 H 5 CH 3 ), ethanol (C 2 H 5 OH), pentane (C 5 H 12 ), ammonia (NH 3 ), hydrogen (H 2 ), and water vapor (H 2 O) at 5 ppm. These results represent potential feasibility for the detection of acetone in exhaled breath for diagnosis of diabetes. [ABSTRACT FROM AUTHOR]

We report on facile synthesis of SnO2 nanofibers (NFs) functionalized by Pt nanoparticles (NPs) with various loading contents (0.05–0.4wt%) and their gas response toward H2, NO2, NH3, CO, and SO2 gases as a function of the operation temperature (100–450°C) and gas concentration (0.125–2.5ppm). Mesoporous SnO2 NFs with large surface-to-volume ratio, which facilitates sensitive gas response, were synthesized by electrospinning followed by subsequent calcination at 500°C for 2h. Colloidal Pt NPs synthesized by simple polyol method were immobilized on SnO2 NFs as a catalytic sensitizer to H2 oxidation. The gas sensing properties and response kinetics were significantly affected by the Pt NPs and the operation temperature. It was found that 0.1wt% Pt-loaded SnO2 sensor showed the highest H2 response (I gas/I air =16.6 at 2.5ppm) at 300°C. A remarkably high NO2 response (I air/I gas =57.0 at 2.5ppm) was achieved in the case of pristine SnO2 sensor at 150°C. This work demonstrates that sensitive and selective detection of H2 and NO2 gases with negligible cross-response to interfering gases such as NH3, CO, and SO2 can be obtained by decoration with Pt NPs on metal oxide NFs in conjunction with manipulation of the operation temperature. [ABSTRACT FROM AUTHOR]

Abstract: The response characteristics of amorphous-InGaZnO4 (a-IGZO4) thin films toward reducing/oxidizing gases (H2/NO2), at sensor operating temperatures, are reported for the first time. The lack of grain boundaries eliminates a major source of electrical, microstructural and chemical inhomogeneities associated with polycrystalline semiconducting metal oxides (SMOs), rendering a-IGZO4 a highly promising model sensor system. Gas sensor tests were carried out in the temperature range of 200–400°C by monitoring changes in DC resistance during cyclic exposure to trace concentrations (between 1.25 and 50ppm) of H2 or NO2 in dry air. The response (S) to H2 was found to go through a temperature maximum (e.g. S ∼0.7 at 350°C for pH2 =12.5ppm) that value being a function of pH2. The response to NO2, on the other hand, decreased with increasing temperatures with the highest recorded values at 200°C (e.g. S ∼33 at 200°C for pNO2 =5ppm). The response followed an approximate power law dependence on gas partial pressure (p), S = Ap β , with β taking on values of ∼0.5–1.0 as temperature increased from 200 to 400°C. Response times were found to range from 10s to greater than 1000s as temperature decreased. The hysteretic behavior exhibited by a-IGZO films between 150 and 400°C, under temperature sweep conditions, is attributed to kinetically limited adsorption/desorption and reaction rates. [Copyright &y& Elsevier]

Abstract: SnO2 hollow nanofibers (HNFs) with diameters of 300–500nm were fabricated via electrospinning of templating nanofibers and RF-sputtering of SnO2 thin overlayers (15–20nm thick and comparable grain size) followed by heat-treatment at 450°C. Gas sensors using these HNFs exhibited n-type gas sensing characteristics and an enhanced gas response to 2ppm NO2 (R gas /R air =81.4) as compared to that (R gas /R air =19.9) of planar SnO2 thin films. The enhanced response to NO2 is attributed to the greater accessible active area and the greater space charge modulation depth associated with the hollow thin walled structures. [Copyright &y& Elsevier]

Abstract: This work presents a simple and versatile route to produce macroporous p-type metal oxide thin films. Two-dimensional arrays of p-type NiO films with a hollow hemisphere structure were fabricated by colloidal templating and RF-sputtering followed by a subsequent heat treatment. The diameter and shell thickness of the NiO hemisphere were 800nm and 20nm, respectively. X-ray diffraction and high-resolution transmission electron microscopy analysis indicate that the pure NiO phase with grain size of 10nm was obtained at calcination temperatures that exceeded 450°C. Close-packed arrays of hollow NiO hemispheres were found to exhibit p-type gas sensing properties against (CO, H2, C3H8, CH4, NO2, and C2H5OH), leading to significantly enhanced responses to C2H5OH (R gas /R air =5.0 at 200ppm). [Copyright &y& Elsevier]

Abstract: This work presents a new route to enhance the sensitivity of nanocrystalline TiO2 fibers based gas sensors. Pure and Pd-doped TiO2 nanofiber mats were synthesized by electrospinning and subsequent calcination. Highly porous fibrillar morphology was observed in the resultant nanocrystalline TiO2 fibers. In addition to anatase TiO2 crystallites, tiny (∼2nm) PdO crystallites were observed in the Pd-doped TiO2 fibers. The sensors using Pd-doped TiO2 fibers showed promising gas sensing characteristics, such as low operation temperature (180°C) and sufficient gas response (R/R o =38 to 2.1ppm NO2). The techniques outlined here offer new means for preparing novel metal-oxide nanofibers with catalytic dopants. [ABSTRACT FROM AUTHOR]

Abstract: To enhance the sensitivity of a metal oxide-based gas sensor, we introduce a novel electrical method that relies jointly on the use of impedance and an applied DC bias. We used polycrystalline ZnO–NiO composite thin films prepared by pulsed layer deposition as CO gas sensor material. The applied DC bias lowers the interface barrier between oxide grains and thereby enhances the sensitivity. Our approach enhances the sensitivity to CO gas by approximately 200% more than a conventional DC method. The enhancement effect is more pronounced when the CO concentration is lowered. This method offers an efficient characterization tool for modulating the sensitivity of gas sensors using semiconducting metal oxides. [Copyright &y& Elsevier]

• The non-noble metals are introduced on graphene-based fiber as a sensitizer for the high-performance chemiresistor. • Metal oxides on graphene fibers naturally are converted into metals at a relatively low temperature annealing (under 700 °C) due to catalytic effect of graphene. • The graphene fiber acts as a flexible conductive support as well as a catalyst for the deoxidation of metal oxide. • The metal/metal oxide/graphene fibers exhibited a 16 times higher response to NO 2 gas and recovery than metal oxide/graphene fiber without metal. • The proposed strategy opens a new avenue for the realization of high-performance devices, such as chemical catalysts, photoactive devices. [Display omitted] Noble metal/metal-oxide-based hybrid gas sensors exhibit a low operating temperature, remarkable sensitivity, and fast recovery. As additives, noble metals induce a catalytic sensitization effect, which promotes charge transfer from the metal oxide to the analyte molecules, the so-called spillover mechanism. This suggests that metal catalysts can improve gas sensing performance. Herein, for the first time, non-noble metals are introduced on hybrid metal oxide/graphene fibers as sensitizers to fabricate high-performance chemiresistive sensors. The formation of metal components can be effectively controlled by annealing the metal oxide on graphene. Remarkably, compared with the corresponding metal oxide/graphene fiber sensors without metal components, the metal/metal oxide/graphene fiber sensors exhibit over a 16-fold higher response to NO 2 gas as well as effective recovery characteristics. Specifically, the Cu/Cu 2 O/graphene and Ni/NiO/graphene fiber sensors operating at 150 °C exhibit sensitivities of 18.90 % and 0.82 %, respectively, for 5 ppm NO 2 gas. The proposed strategy to achieve flexible graphene fiber chemiresistors by decorating them with non-noble metal and metal oxide nanoparticles opens a new avenue for realizing high-performance devices, such as photovoltaic devices, photocatalysts, and chemical catalysts. [ABSTRACT FROM AUTHOR]

• Porosity control of nanofibers: The high porosity of the metal oxide nanofibers is the key to achieving the dual sensitization owing to their high gas permeability and numerous active sites. Both saponin and water-ethanol co-solvent play critical roles in modifying morphology of nanofibers into elliptical nanofibers during electrospinning. Additionally, saponin forms numerous pores in the nanofibers when being burnt out during calcination. These porous, elliptical nanofibers possess a larger surface area and porosity.Saponin and water-ethanol co-solvent enabled porous, elliptical nanofibers to emerge. • Bifunctional Ga doping: Ga dopants enhanced sensing performance via conductivity improvement and grain growth inhibition. • Functionalization of Pt catalysts : Spill-over effects and chemical sensitization of remarkably improved C 2 H 2 sensitivity. Herein, we demonstrate a sensitization strategy via solid-solution doping and catalytic metal nanoparticles (NPs) onto porous metal oxide nanofibers (NFs) for superior acetylene (C 2 H 2) sensing capabilities. The introduction of dopants and catalysts not only increases the inherent reactivity of metal oxides, but also induces the spillover of C 2 H 2 onto metal oxides, significantly improving the sensing properties. We elucidate that the high porosity of the metal oxide NFs, prepared by electrospinning and utilizing saponin as a sacrificial template, is the key to achieving high gas permeability and numerous active sites. Consequently, Ga-doped ZnO porous NFs functionalized with Pt catalysts exhibited the highest C 2 H 2 sensing responses among the current state-of-the-art C 2 H 2 sensors (R a /R g = 26.2 at 400 °C) with a fast response time (10.2 s), at a particularly low concentration of 5 ppm. Moreover, these NFs showed excellent selectivity against the interfering gas (H 2 , C 7 H 8 , CO, CH 4 , C 8 H 10 , CH 3 COCH 3 , HCHO and C 2 H 5 OH) and outstanding stability up to 20 sensing cycles to 0.4 ppm of C 2 H 2. These results provide an efficient strategy to tailor composites of metal oxide nanostructures, dopants, and catalysts for highly sensitive gas sensors. [ABSTRACT FROM AUTHOR]