Search

This paper presents a localization system for Unmanned Aerial Vehicles (UAVs) especially designed to be used in infrastructure inspection, where the UAVs have to fly in challenging conditions, such as relatively high altitude (e.g., 15 m), eventually with poor or absent GNSS (Global Navigation Satellite System) signal reception, or the need for a BVLOS (Beyond Visual Line of Sight) operation in some periods. In addition, these infrastructure inspection applications impose the following requirements for the localization system: defect traceability, accuracy, reliability, and fault tolerance. Our system proposes a lightweight solution combining multiple stereo cameras with a robotic total station to comply with these requirements, providing full-state estimation (i.e., position, orientation, and linear and angular velocities) in a fixed and time-persistent reference frame. Moreover, the system can align and fuse all sensor measurements in real-time at high frequency. We have integrated this localization system in our aerial platform, and we have tested its performance for inspection in a real-world viaduct scenario, where the UAV has to operate with poor or absent GNSS signal at high altitude.

This paper presents the design, modeling and control of a fully actuated aerial robot for infrastructure contact inspection as well as its localization system. Health assessment of transport infrastructure involves measurements with sensors in contact with the bridge and tunnel surfaces and the installation of monitoring sensing devices at specific points. The design of the aerial robot presented in the paper includes a 3DoF lightweight arm with a sensorized passive joint which can measure the contact force to regulate the force applied with the sensor on the structure. The aerial platform has been designed with tilted propellers to be fully actuated, achieving independent attitude and position control. It also mounts a “docking gear” to establish full contact with the infrastructure during the inspection, minimizing the measurement errors derived from the motion of the aerial platform and allowing full contact with the surface regardless of its condition (smooth, rough, ...). The localization system of the aerial robot uses multi-sensor fusion of the measurements of a topographic laser sensor on the ground and a tracking camera and inertial sensors on-board the aerial robot, to be able to fly under the bridge deck or close to the bridge pillars where GNSS satellite signals are not available. The paper also presents the modeling and control of the aerial robot. Validation experiments of the localization system and the control system, and with the aerial robot inspecting a real bridge are also included.

This paper presents a robotic system using Unmanned Aerial Vehicles (UAVs) for bridge-inspection tasks that require physical contact between the aerial platform and the bridge surfaces, such as beam-deflection analysis or measuring crack depth with an ultrasonic sensor. The proposed system takes advantage of the aerodynamic ceiling effect that arises when the multirotor gets close to the bridge surface. Moreover, this paper describes how a UAV can be used as a sensor that is able to fly and touch the bridge to take measurements during an inspection by contact. A practical application of the system involving the measurement of a bridge’s beam deflection using a laser tracking station is also presented. In order to validate our system, experiments on two different bridges involving the measurement of the deflection of their beams are shown.

The Helicopter Adaptive Aircraft (HADA) is a morphing aircraft which is able to take-off as a helicopter and, when in forward flight, unfold the wings that are hidden under the fuselage, and transfer the power from the main rotor to a propeller, thus morphing from a helicopter to an airplane. In this process, the reliable folding and unfolding of the wings is critical, since a failure may determine the ability to perform a mission, and may even be catastrophic. This paper proposes a virtual sensor based Fault Detection, Identification and Recovery (FDIR) system to increase the reliability of the HADA aircraft. The virtual sensor is able to capture the nonlinear interaction between the folding/unfolding wings aerodynamics and the HADA airframe using the navigation sensor measurements. The proposed FDIR system has been validated using a simulation model of the HADA aircraft, which includes real phenomena as sensor noise and sampling characteristics and turbulence and wind perturbations.

This paper presents a method to increase the reliability of Unmanned Aerial Vehicle (UAV) sensor Fault Detection and Identification (FDI) in a multi-UAV context. Differential Global Positioning System (DGPS) and inertial sensors are used for sensor FDI in each UAV. The method uses additional position estimations that augment individual UAV FDI system. These additional estimations are obtained using images from the same planar scene taken from two different UAVs. Since accuracy and noise level of the estimation depends on several factors, dynamic replanning of the multi-UAV team can be used to obtain a better estimation in case of faults caused by slow growing errors of absolute position estimation that cannot be detected by using local FDI in the UAVs. Experimental results with data from two real UAVs are also presented.