Search

Abstract Anger suppression is important in our daily life, as its failure can sometimes lead to the breaking down of relationships in families. Thus, effective strategies to suppress or neutralise anger have been examined. This study shows that physical disposal of a piece of paper containing one’s written thoughts on the cause of a provocative event neutralises anger, while holding the paper did not. In this study, participants wrote brief opinions about social problems and received a handwritten, insulting comment consisting of low evaluations about their composition from a confederate. Then, the participants wrote the cause and their thoughts about the provocative event. Half of the participants (disposal group) disposed of the paper in the trash can (Experiment 1) or in the shredder (Experiment 2), while the other half (retention group) kept it in a file on the desk. All the participants showed an increased subjective rating of anger after receiving the insulting feedback. However, the subjective anger for the disposal group decreased as low as the baseline period, while that of the retention group was still higher than that in the baseline period in both experiments. We propose this method as a powerful and simple way to eliminate anger.

Abstract Oil-immersed transformers are expensive equipment in the electrical system, and their failure would lead to widespread blackouts and catastrophic economic losses. In this work, an elaborate diagnostic approach is proposed to evaluate twenty-six different transformers in-service to determine their operative status as per the IEC 60599:2022 standard and CIGRE brochure. The approach integrates dissolved gas analysis (DGA), transformer oil integrity analysis, visual inspections, and two Back Propagation Neural Network (BPNN) algorithms to predict the loss of life (LOL) of the transformers through condition monitoring of the cellulose paper. The first BPNN algorithm proposed is based on forecasting the degree of polymerization (DP) using 2-Furaldehyde (2FAL) concentration measured from oil samples using DGA, and the second BPNN algorithm proposed is based on forecasting transformer LOL using the 2FAL and DP data obtained from the first BPNN algorithm. The first algorithm produced a correlation coefficient of 0.970 when the DP was predicted using the 2FAL measured in oil and the second algorithm produced a correlation coefficient of 0.999 when the LOL was predicted using the 2FAL and DP output data obtained from the first algorithm. The results show that the BPNN can be utilized to forecast the DP and LOL of transformers in-service. Lastly, the results are used for hazard analysis and lifespan prediction based on the health index (HI) for each transformer to predict the expected years of service.

Abstract As the social organism, Polistes wasps build a communal nest using woody fibers with saliva for sustaining brood and adult population throughout the season. Limited information exists regarding the identification specific plant materials employed in wasp nest building. Thus, we firstly tested if the DNA metabarcoding approach utilizing rbcL and trnL molecular markers could identify the plant species quantitatively and qualitatively inform the mixed-origin woody samples. A threshold of 0.01 proportion of reads was applied for rbcL and trnL molecular markers, while this threshold for median proportion was 0.0025. In assessing taxa richness, the median proportion demonstrated superior performance, exhibiting higher taxa detection power, however, rbcL marker outperformed in quantitative analysis. Subsequently, we applied DNA metabarcoding to identify the plant materials from the nests of two Polistes species, P. mandarinus and P. rothneyi. The results showed that higher preference of Quercus and Robinia as the major nest building materials regardless of the surrounding plant communities, by two wasp species. Material diversity was higher for P. rothneyi than P. mandarinus, which may explain the abundance of this species possibly with heightened adaptive capacities in their nesting behavior. This study demonstrated that DNA metabarcoding could identify the complex nest-building plant materials of paper wasps and provide insights into their ecological interactions in the natural ecosystem.

Abstract This article presents the results of an experiment designed to study the impact of temperature on the characteristic parameters of creeping discharges. The insulating interfaces consist of a thermally enhanced cellulose surface immersed in mineral oil, palm kernel oil methyl ester (PKOME) and castor oil methyl ester (COME). The study was carried out under a standard negative lightning impulse voltage (1.2/50 μs). The article also presents the complete algorithms for calculating the maximum extension of the discharges, the ionisation rate and the charge produced by them. The results of the study show that temperature favors the propagation of discharges and the ionisation rate. It was observed that liquids with a higher dielectric constant and high electrical conductivity were more exposed to the impact of temperature. The results show ionisation increments of 0.973%/°C, 1.093%/°C and 1.076%/°C in mineral oil (MO), COME and PKOME respectively. The maximum extension of the discharges shows a linear evolution with the applied voltage and temperature but a non-linear increment with the temperature. As for the charge produced, it shows a constant increment with temperature and voltage in each liquid. These values are (5.839%/°C, 1.977%/kV), (6.047%/°C, 2.082%/kV) and (6.177%/°C, 2.113%/kV) respectively in MO, COME and PKOME.

Abstract Energy storage devices (ESD) which are intended to power electronic devices, used in close contact of human skin, are desirable to be safe and non-toxic. In light of this requirement, Zn based energy storage devices seem to provide a viable pathway as they mostly employ aqueous based electrolytes which are safe and non-toxic in their functioning. Additionally, having a flexible ESD will play a crucial role as it will enable the ESD to conform to the varying shapes and sizes of wearable electronics which they energize. In this work, we have developed an inkjet-printed Zinc ion battery (IPZIB) with planar electrode configuration over bond paper substrate. Zn has been used as the negative electrode, MnO2 is used as the positive electrode with Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) as the active binder. Conducting tracks of reduced graphene oxide (rGO) are used to construct the current collector on the paper substrate. The fabricated IPZIB delivered a high discharge capacity of 300.14 mAh g−1 at a current density of 200 mA g−1. The energy density of the IPZIB is observed as 330.15 Wh kg−1 at a power density of 220 W kg−1 and retains an energy density of 94.36 Wh kg−1 at a high power density of 1650 W kg−1. Finally, we have demonstrated the capability of the IPZIB to power a LED at various bending and folding conditions which indicates its potential to be used in the next generation flexible and wearable electronic devices.

This article presents the results of an experiment designed to study the impact of temperature on the characteristic parameters of creeping discharges. The insulating interfaces consist of a thermally enhanced cellulose surface immersed in mineral oil, palm kernel oil methyl ester (PKOME) and castor oil methyl ester (COME). The study was carried out under a standard negative lightning impulse voltage (1.2/50 μs). The article also presents the complete algorithms for calculating the maximum extension of the discharges, the ionisation rate and the charge produced by them. The results of the study show that temperature favors the propagation of discharges and the ionisation rate. It was observed that liquids with a higher dielectric constant and high electrical conductivity were more exposed to the impact of temperature. The results show ionisation increments of 0.973%/°C, 1.093%/°C and 1.076%/°C in mineral oil (MO), COME and PKOME respectively. The maximum extension of the discharges shows a linear evolution with the applied voltage and temperature but a non-linear increment with the temperature. As for the charge produced, it shows a constant increment with temperature and voltage in each liquid. These values are (5.839%/°C, 1.977%/kV), (6.047%/°C, 2.082%/kV) and (6.177%/°C, 2.113%/kV) respectively in MO, COME and PKOME., (© 2024. The Author(s).)