Search

An experimental study to investigate the flow of liquid jet issued from a high aspect ratio nozzle slit into an incoming airflow by changing the orientation angle from the incoming free-stream was performed. A two-dimensional liquid sheet emerged from the narrow slit into the subsonic air crossflow. Different orientation angles between 0 and 90 degrees were studied. High-speed photography and shadowgraphy techniques were utilized to visualize the flow physics. The influence of the slit orientation angle on the flow morphology and the flow regimes of liquid sheets was investigated. Some fluid flow parameters were obtained by analyzing the images. The changes in breakup height of different orientations were measured. A model was offered for the breakup height of the liquid sheet based on the liquid-to-gas momentum ratio, gas Weber number, and a new non-dimensional parameter as a representation of the angle of slit orientation. Also, the defined sheet trajectory for each orientation angle was obtained, and the variations were examined. Empirical correlations for the defined trajectory of the sheet in terms of liquid to gas momentum ratio and gas Weber number for each orientation angle were proposed. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) panels are similar in many aspects to the leaves of trees, both are standing in the Sun to capture the sunlight, however, PV panels get soiled especially in desert areas, while the leaves remain clean to a very good extent. The question is, why leaves remain clean while PV panels get soiled quite easily? The leaves are hanging on the stem of trees and these stems are flexible to motion, such that if the wind blows in any direction over the stem it vibrates allowing any deposited particle to fall off the surface. The objective of this research is to develop a fixation method for PV panels similar to the stems of trees, such that the panel can vibrate as the wind blows in order to minimize dust accumulation. Different fixation methods for the PV panel are designed, and the air flow around the panel is simulated using the CFD package Ansys Fluent. It has been found that a PV panel pivoted at its lower edge, such that it can revolve around the lower edge, together with a vertical wind shield attached to its upper edge and a spring attached at the middle of its backside has the largest vibration amplitude due to the applied wind compared to the other designs. Experiments have been done to infer the influence of the new fixation method of the PV panel on dust accumulation over the panel. After 6 weeks of operation, it has been found that the efficiency of the PV panel that is flexibly fixed has dropped by only 5%, while the efficiency of the panel that is rigidly fixed has dropped by 25%. It can be concluded that a PV panel operating a light post should be fixed on a flexible base that allows the panel to vibrate as the wind blows over it in order to mitigate dust. [ABSTRACT FROM AUTHOR]

Odours used by insects for foraging and mating are carried by the air. Insects induce airflows around them by flapping their wings, and the distribution of these airflows may strongly influence odour source localisation. The flightless silkworm moth, Bombyx mori, has been a prominent insect model for olfactory research. However, although there have been numerous studies on antenna morphology and its fluid dynamics, neurophysiology, and localisation algorithms, the airflow manipulation of the B. mori by fanning has not been thoroughly investigated. In this study, we performed computational fluid dynamics (CFD) analyses of flapping B. mori to analyse this mechanism in depth. A three-dimensional simulation using reconstructed wing kinematics was used to investigate the effects of B. mori fanning on locomotion and pheromone capture. The fanning of the B. mori was found to generate an aerodynamic force on the scale of its weight through an aerodynamic mechanism similar to that of flying insects. Our simulations further indicate that the B. mori guides particles from its anterior direction within the ~ 60° horizontally by wing fanning. Hence, if it detects pheromones during fanning, the pheromone can be concluded to originate from the direction the head is pointing. The anisotropy in the sampling volume enables the B. mori to orient to the pheromone plume direction. These results provide new insights into insect behaviour and offer design guidelines for robots for odour source localisation. [ABSTRACT FROM AUTHOR]

Because of the lack of good seedling positioning during vegetable grafting, there are issues such as high labor costs and long grafting time. This article proposes a negative pressure suction seedling positioning method for seed leaves based on the characteristic parameters of cucumber spike wood, and designs a flexible adsorption positioning mechanism for spike wood. Firstly, the ventral surface curve trajectories of cucumber cotyledons were extracted using Matlab software, and then a shape-adaptive design was applied to the attachment surface of the flexible suction positioning mechanism, and a computational fluid dynamics model of the airflow field was established. By combining Fluent simulation analysis with orthogonal experiments, the effect of suction hole diameter, vacuum negative pressure value, suction hole quantity, and suction hole depth on the adsorption effect of the suction head was analyzed, the main and secondary factors and operational indicators that affect the adsorption effect are evaluated. The optimal parameter combination: suction hole diameter of 1.5 mm, vacuum negative pressure value of 2 kPa, suction hole quantity of 42, and suction hole depth of 2 mm, has been found. A verification experiment was conducted on a test bench, and the experimental results show that the success rate of leaf absorption using the optimal parameter combination is 97.69%, which indicates that the suction head is designed reasonably and meets the requirements of grafting. [ABSTRACT FROM AUTHOR]

Obstructive sleep apnea (OSA) is an airway disease caused by periodic collapse of the airway during sleep. Imaging-based subject-specific computational fluid dynamics (CFD) simulations allow non-invasive assessment of clinically relevant metrics such as total pressure loss (TPL) in patients with OSA. However, most of such studies use static airway geometries, which neglect physiological airway motion. This study aims to quantify how much the airway moves during the respiratory cycle, and to determine how much this motion affects CFD pressure loss predictions. Motion of the airway wall was quantified using cine MRI data captured over a single respiratory cycle in three subjects with OSA. Synchronously-measured respiratory airflow was used as the flow boundary condition for all simulations. Simulations were performed for full respiratory cycles with 5 different wall boundary conditions: (1) a moving airway wall, and static airway walls at (2) peak inhalation, (3) end inhalation, (4) peak exhalation, and (5) end exhalation. Geometric analysis exposed significant local airway cross-sectional area (CSA) variability, with local CSA varying as much as 300%. The comparative CFD simulations revealed the discrepancies between dynamic and static wall simulations are subject-specific, with TPL differing by up to 400% between static and dynamic simulations. There is no consistent pattern to which static wall CFD simulations overestimate or underestimate the airway TPL. This variability underscores the complexity of accurately modeling airway physiology and the importance of considering dynamic anatomical factors to predict realistic respiratory airflow dynamics in patients with OSA. [ABSTRACT FROM AUTHOR]

Metallic microfluidic devices made from powder-bed additive manufacturing systems have received increasing attention, but their feasible channel geometry and complexity are often limited by lack of an effective approach to removing trapped powder particles within the channels or conduits of the sintered parts. Here, we present an innovative approach to fabricating long serpentine, high-aspect-ratio submillimeter channels made of stainless steel 316L (SS) by binder jet printing (BJP) and liquid-phase sintering. We leverage the unique nature of the BJP process, that is printing and consolidation steps are decoupled, enabling us to join two or more parts during the sintering step. Instead of constructing the channel device as a single part, we print multiple parts for easy powder removal and later join them to form enclosed channels. The key innovation lies in adding sintering additives like boron nitrides (BN) to the SS stock powder—at the SS/BN interfaces, liquid phase is locally generated at temperature much lower than the SS melting temperature, facilitating the bonding of the multiple parts as well as the consolidation of parts for near-full density. We systematically vary the sintering temperature to show how it affects the joining quality and the channel shape distortion. The joining quality such as the fracture strengths of the joined samples is measured by a pull test while the shape distortion is characterized by various imaging techniques. The feasibility of the proposed approach is demonstrated by fabricating a 400-mm-long, fully enclosed serpentine channel with a rectangular cross-section of 0.5 mm in width and 1.8 mm in height. The pressure drop across this 3D-printed SS serpentine channels is measured for air flow and compared to a standard gas flow model, showing that the device is free of leakage or clogs. [ABSTRACT FROM AUTHOR]

This work presents a novel approach to investigating the slip effect in nanofiber filter media. Electrospun nanofiber media with high efficiency and low pressure drop were produced at different concentrations and durations. The surface and cross-sectional morphology of nanofiber media were studied using FE-SEM. Fiber orientation and diameter distributions were also examined. The 3D virtual nanofiber media was modeled using this information along with the experimentally measured porosity and thickness of the media. The effect of the slip phenomenon in nanofiber media was studied numerically, and the results were compared to experimental data. Excellent agreements were found between the measured and simulation results. Additionally, filtration simulations considering aerosols injected with airflow through the nanofibrous filter media were conducted by considering the slip effect, and the effect of filter structure on filtration performance (removal efficiency and pressure drop) was investigated. [ABSTRACT FROM AUTHOR]

Coronaviruses being capable of spreading through droplet contamination have raised significant concerns regarding high-capacity public rail transport, such as the metro. Within a rapidly moving railcar cabin, the internal airflow lags behind the bulkhead, generating internally induced airflow that accelerates droplet dispersion within a non-inertial reference system. This study investigates the impact of acceleration on the diffusion of cough droplets of varying sizes using computational fluid dynamics. The modified k–ε equation in ANSYS® Fluent was utilized to simulate droplet diffusion under different body orientations by adjusting the inertial force correction source term. Results indicate that droplets in the middle size range (50–175 μm) are primarily influenced by inertial forces, whereas smaller droplets (3.5–20 μm) are predominantly controlled by air drag forces. Regardless of facial orientation, the outlet of high-capacity public rail transport poses the highest risk of infection. [ABSTRACT FROM AUTHOR]

To study the characteristics of nasal airflow in the presence of nasal cycle by computational fluid dynamics. CT scan data of a healthy Chinese individual was used to construct a three-dimensional model of the nasal cavity to be used as simulation domain. A sinusoidal airflow velocity is set at the nasal cavity entrance to reproduce the breathing pattern of a healthy human. There was a significant difference in the cross-sectional area between the two sides of the nasal cavity. Particularly, the decongested side is characterized by a larger cross-section area, and consequently, by a larger volume with respect to the congested side. The airflow velocity, pressure, and nasal resistance were higher on the congested narrow side. The temperature regulation ability on the congested narrow side was stronger than that on the decongested wider side. During the nasal cycle, there are differences in the nasal cavity function between the congested and decongested sides. Therefore, when evaluating the impact of various factors on nasal cavity function, the nasal cycle should be considered. [ABSTRACT FROM AUTHOR]

Positive pressure ventilators (PPV) used by 97.7% of officers of the National Fire Service in Poland, are characterized by work that is not in line with the expectations of the firefighters. In order to improve the technical and operational features of these devices, a survey was conducted among 25,000 eligible firefighters, identifying the application of these devices, problems in use and expected development directions. A total of 682 officers voluntarily completed the survey. Based on their findings, it was determined that ventilators are most often used to smoke out buildings after or during a fire. Mentioned problems when using these devices were mainly noise (78.2%), exhaust emissions (68.5%), and impediments to mobility through the device's relatively heavy weight (40.2%). Other inconveniences were mentioned by less than 20% of firefighters. Polish firefighters expect the development of these devices mainly in terms of the above-mentioned features (noise reduction (81.7%) and reduction of the weight and size of the ventilators (about 50%)). Other expectations relate to the improvement of smoke removal in buildings: increasing the efficiency of smoke removal (46.4%) and efficiency regarding the rate of smoke removal in a building by increasing the size of the incoming airflow from the building's surroundings (33.2%). About 15% of firefighters expect changes in the operation of the ventilator itself, that is, an increase in the effective operating time (electric ventilators) and an increase in the device's uptime. The aim of the article is to identify the issues encountered during the operation and to indicate the expected direction of development for PPV by users. This information can be used by engineers to initiate new development work on these devices. [ABSTRACT FROM AUTHOR]

This study compared computational fluid dynamic (CFD) model predictions on aerosol deposition in six asthmatic patients to the in-vivo results of the same group. Patient-specific ventilation and internal air distribution were prescribed using inspiratory and expiratory CT scans of each patient, accounting for individual lobar air flow distribution. Moreover, the significant influence of realistic mouth and throat geometries on regional deposition is demonstrated. The in-vivo data were obtained from single photon emission computed tomography (SPECT) in 6 subjects with mild asthma selected from a database of historical clinical trials. The governing flow and particle tracking equations were solved numerically using a commercial CFD tool, and the modeled deposition results were compared to the SPECT data. Good agreement was found between the CFD model, applying k-ω SST turbulence model, and SPECT in terms of aerosol deposition. The average difference for the lobar deposition obtained from CFD model and SPECT/CT data was 2.1%. The high level of agreement is due to applying patient specific airway geometries and inspiratory/expiratory CT images, anatomical upper airways, and realistic airway trees. The results of this study show that CFD is a powerful tool to simulate patient-specific deposition if correct boundary conditions are applied and can generate similar information obtained with functional imaging tools, such as SPECT. [ABSTRACT FROM AUTHOR]

We investigated (1) how nasal septal perforations (NSPs) modify nasal airflow and air-conditioning characteristics and (2) how the modifications of nasal airflow are influenced by the size and location of the NSP. Computed tomography scans of 14 subjects with NSPs were used to generate nasal cavity models. Virtual repair of NSPs was conducted to examine the sole effect of NSPs on airflow. The computational fluid dynamics technique was used to assess geometric and airflow parameters around the NSPs and in the nasopharynx. The net crossover airflow rate, the increased wall shear stress (WSS) and the surface water–vapor flux on the posterior surface of the NSPs were not correlated with the size of the perforation. After the virtual closure of the NSPs, the levels in relative humidity (RH), air temperature (AT) and nasal resistance did not improve significantly both in the choanae and nasopharynx. A geometric parameter associated with turbinate volume, the surface area-to-volume ratio (SAVR), was shown to be an important factor in the determination of the RH and AT, even in the presence of NSPs. The levels of RH and AT in the choanae and nasopharynx were more influenced by SAVR than the size and location of the NSPs. [ABSTRACT FROM AUTHOR]

In recent years, research on ventilating tunnels has become increasingly important. However, the impact of external disturbances on ventilating systems has been largely ignored. To address this issue of frequent airflow fluctuations caused by external perturbations, which cannot be fully compensated using conventional control methods, this study proposes a perturbation-compensated ventilation control approach. A disturbance compensator is developed by incorporating the tunnel's airflow velocity and the number of jet fan start-stop events as input parameters. By compensating for external disturbances, the disturbance to the system is reduced. The Simulink model of the tunnel controller was used for simulation experiments. The compensator demonstrated good tracking results in comparison experiments with different disturbances. The ventilation approach based on disturbance compensator is capable of regulating the fluctuation of CO concentration within a justifiable range compared to using PID control and ADRC. This not only improves the stability of the entire control system but also significantly prolongs the service life of the jet fan by reducing the frequency of start-stop cycles. [ABSTRACT FROM AUTHOR]