Search

This paper clarifies aggressivity reduction approach for MPV, Multi-Purpose Vehicles, derived from large passenger vehicles toward small passenger vehicles. The effects of aggressivity-reducing approach were measured through full-frontal rigid barrier crash simulations with TRL aluminum honeycomb by Finite Element Method. The front-end structures of large vehicles studied in this paper based on this aggressivity reduction approach show good front-end homogeneity and low average height of force. The structures were also found to effectively reduce aggressivity toward small vehicles by car-to-car simulation. However, there are some cases where the effect was influenced by overlap ratios. From this result, overlap ratio is considered to be one of the important factors to improve compatibility performance.

A burning process in a combustion chamber of an internal combustion engine is very important to know the maximum temperature of the gases, the speed of combustion, the ignition delay time of fuel and air mixture exact moment at which ignition will occur. The automobilist industry has invested considerable amounts of resources in numerical modeling and simulations in order to obtain relevant information about the processes in the combustion chamber and then extract the maximum engine performance control the emission of pollutants and formulate new fuels. This study aimed to general construction and instrumentation of a shock tube for measuring shock wave. As specific objective was determined reaction rate and ignition delay time of diesel and ethanol doped with different levels of additive enhancer cetane number. The results are compared with the delays measured for the ignition diesel and biodiesel.

This paper presents a high-fidelity electro-thermal model of a half-bridge that consists of IGBTs and anti-parallel diodes. The model calculates and estimates the half-bridge voltages, currents, switching and conduction losses considering the operating temperature and current conditions. Moreover, this model is suitable for varying switching frequency operation. The electro-thermal model can be used as an evaluation tool to analyze the performance of control strategies for traction inverter from efficiency, temperature and component stress point of view. In this paper performance of Direct Torque Model Predictive Control (DTMPC) of an Interior Permanent Magnet Synchronous Motor (IPMSM) is evaluated in comparison with Indirect Field Oriented Control (IFOC) with sinusoidal pulse width modulation (PWM). The inverter model and the MPC are both implemented in C-Mex for rapid execution. The MPC algorithm implemented in this research tracks torque reference while using Maximum-Torque-Per-Ampere (MTPA) strategy and minimizing switching losses. Both control systems are able to follow the speed reference. The MPC shows a decrease in losses compared to IFOC when tested with low-speed and high-speed parts of the WLTC profile.

he use of lean or ultra-lean ratios is an efficient and proven strategy to reduce fuel consumption and pollutant emissions. However, the lower fuel concentration in the cylinder hinders the mixture ignition, requiring greater energy to start the combustion. The prechamber is an efficient method to provide high energy favoring the ignition process. It presents the potential to reduce the emission levels and the fuel consumption, operating with lean burn mixtures and expressive combustion stability. In this paper the analysis of the combustion process of SI engines equipped with an innovative architecture and operating in different injection modes was described. In particular, the effect of the prechamber ignition on the engine stability and the efficiency was investigated in stoichiometric and leanburn operation conditions. The activity was carried out in two parts. In the first part the investigation was performed in a research small direct injection spark ignition (DISI) engine, running at 2000 rpm WOT, and fueled with Methane. The combustion process was studied using optical diagnostics. Methane was injected both in the prechamber and in the main chamber through the port fuel injection (PFI) mode. The ignition was obtained with a properly designed fueled prechamber prototype. It was equipped with a gas direct injector, used to inject the fuel into the prechamber, and a spark plug used to ignite the mixture. The gaseous fuel in the main chamber was ignited by the plasma jets coming from the prechamber. The combustion of the prechamber mixture generates four plasma jets that quickly ignite the mixture into the combustion chamber, and the flame speed is much faster than the traditional ignition. The optical data were correlated with the engine performance and indicated measurements that showed an increase of the Indicated Mean Effective Pressure (IMEP) and the reduction of the Coefficient of Variation (CoV). In the second part, the optimization of the gasoline combustion by means of a passive prechamber was performed. The investigation was carried out in a commercial small SI engine at 2000 rpm, fueled with gasoline in PFI mode and equipped with the same prechamber used in the first part of the activity. But in this case the prechamber works in passive mode.

International audience; Global warming has put the transport sector, a major contributor of CO 2 emissions, under high pressure to improve efficiency. In this context, ultra-light vehicles weighting less than 500 kg, as well as hybrid powertrains, are nowadays seen as promising development trends. The design process of the powertrain of a vehicle combining the advantages of the two concepts is presented in this paper. Through a performance study based on a simple MATLAB model, and mathematical simulation, a proposal is made. A powertrain using a battery and supercapacitor 48V dual power source network, two electric motors and clutches to switch between conventional, parallel, series and full electric modes proves to be an interesting system in terms of performance and costs. A simulation study conducted on a scenario with different outcome possibilities showed that high modularity of the system allows to achieve fuel efficiencies equivalent to approximately 3 l/100 km on the Artemis cycle. Finally, integration, packaging and cost are considered and some hints for further powertrain efficiency improvements are presented.

For the past thirty years heavy duty diesel oil performance has been defined by the API CD category type tests. During this time the trend in CD oils has been toward lower ash and lower TBN. This has been largely due to the performance improvements of ashless components which now form a major part of today's HD formulations. PC-1 type category testing indicates that ashless components will continue to be effective in meeting these higher heavy duty diesel targets. As a result, lower ash PC-1 type formulations are feasible. Oils have been developed using the dynamometer engine tests currently being worked with to define PC-1 to meet the target of improved oil consumption. These oils are also showing similar advantages in field performance testing over current CD/SF quality lubricants.

A study has been done to determine the effect of changes in diesel injection timing on engine performance using a multicylinder, turbocharged diesel engine fumigated with ethanol. Tests at half load with engine speeds of 2000 and 2400 rpm indicated that a 4% increase in thermal efficiency could be obtained by advancing the diesel injection timing from 18 to 29/sup 0/BTDC. The effect of changes in diesel timing was much more pronounced at 2400 rpm. Advancing the diesel timing decreased CO and unburned HC levels significantly. The increase in NO levels due to advances in diesel timing was offset by the decrease in NO due to ethanol addition.

It has been predicted that the prevailing COVID-19 situation would result in increased demand for personal vehicles. There is a renewed interest in the 3 wheeled vehicles for short urban mobility in western countries due to their inherent cost advantages which will make it affordable for the common man. As the world is moving towards electric vehicle technology, a light 3 wheeled vehicle option will also help in reducing battery weight and thereby help in addressing the range concerns. In addition, slow speed 3-wheelers need not pass extensive safety regulation tests in many western countries including the USA. Three-wheeled vehicles are not new to developing countries like India as three-wheeled auto-rickshaws are quite popular for short distance shared travel. The existing single front wheel design known as delta design may have a stigma attached to it due to historic reasons in India. There is also a perception that the three-wheeled vehicles are highly unstable. Therefore, the current paper studies in detail an alternate design known as the tadpole design having two wheels in the front. The tadpole configuration facilitates decent styling and good aerodynamics. The tadpole configuration is modeled and analyzed using CAE multibody dynamics software, MSC Adams Car. To get confidence in the simulation results, a few benchmarked and tested vehicles are selected from the available literature [1] and the MBD results are compared for correlation. The studies also include a standard four-wheeled vehicle and a delta configuration 3-wheeler for reference purpose. The MBD virtual analyses provide results for vehicle stability and handling characteristics like overturning speed limit, oversteer and understeer behavior during constant radius cornering tests. The paper, by keeping in mind the typical urban driving condition and pattern, gives its feedback and recommendation about the tadpole configured 3-wheeler. © 2021 SAE International. All rights reserved.

The paper deals with the reduction of pollutant emissions in urban areas by considering a Zero-Emission Zone (ZEZ) in which hybrid electric vehicles (HEVs) are allowed to be driven without using the internal combustion engine, as several cities have planned to realize in the next decades. Moreover, since vehicle connectivity has spread more and more in the last years, a vehicle-to-network (V2N) communication system has been taken into account to retrieve real-time navigation data from a map service provider and thus reconstructing the so-called electronic horizon, which is a reconstruction of the future conditions of the vehicle on the road ahead. The speed profile and the road slope are used as input for an on-board predictive control strategy of a plug-in HEV (PHEV). In particular, a dedicated algorithm predicts the amount of necessary energy to complete the city event in full-electric mode, giving a state of charge (SoC) target value. With this aim, an adaptive equivalent consumption minimization strategy (A-ECMS) has been modified to use navigation data for approaching the ZEZ with the target SoC. The paper finally quantifies the benefits of such an approach in terms of CO2 emissions by comparing it with a heuristic, rule-based one, which represents the standard OEM solution.

In the context of a transport sustainability, some solutions could be proposed from the integration of many disciplines, architects, environmentalists, policy makers, and consequently it may be addressed with different approaches. These solutions would be applied at different geographical levels, i.e. national, regional or urban scale. Moreover, the assessment of cars emissions in real use plays a fundamental role for their reductions. This is also the direction of the new harmonized test procedures (WLTP). Furthermore, it is fundamental to keep in mind that the new WLTC cycle will reproduce a situation closer to the reality comparing to the EUDC/NEDC driving cycle. In this paper, we will be focused on vehicle kinematic evaluation aimed at valuation of traffic situation and emissions. For this purpose, driving data and emissions were acquired during an experimental campaign through six instrumented vehicles by PEMS for the simultaneous acquisition of emissions, kinematic variables and GPS localization data. Moreover, the analyzed vehicles have different type approval classes and different displacements. At this time, we present a different statistical approach to classify the pieces of speed parts in order to identify typical traffic situation and their emission evaluation. Finally, apply some statistical criteria, and going in the same direction of WLTC, a driving cycle composed by a succession of speed parts was built.

Battery electric vehicles (BEV) share the ability of regenerative braking since they are equipped with two independent types of deceleration devices, namely the electric motor working as a generator and the friction brakes. Correct interaction of these systems in terms of driving safety and energy efficiency is a function of the Brake Blending Control. Individual electric motors for each wheel and a decoupled brake system provides the Brake Blending with a high design flexibility that allows significant advantages regarding energy consumption, brake performance, and driving comfort. This paper is focusing on the fail behaviour and analyses the robustness and redundancy abilities of such systems against various error scenarios. For this purposes, a distributed x-in-the-loop environment, consisting of dedicated simulation and hardware testing components, is introduced. The investigation is carried out based on a high-fidelity real-time simulation model of an electric sport utility vehicle with four in-wheel motors (IWM) and decoupled electro-hydraulic brake system. This model can be used for a detailed analysis of vehicle dynamics in case of brake system fails. The electro-hydraulic decoupled brake system is implemented through a Hardware-in-the-loop test rig, which allows a realistic fault injection. The vehicle stability and controllability is investigated under the circumstances of various brake system failures in the regenerative and friction brake system, respectively. These studies are presented according to standardized test scenarios like Straight line braking (DIN 70028) and Brake-in-turn (ISO 7975). With obtained x-in-the-loop simulation results, the impact of a failure on vehicle dynamics is discussed in the final part of the paper.

This paper presents analytical research conducted into the level of fuel consumption improvement that can be expected from turbocompounding a medium-duty opposed-piston 2-stroke engine, which is part of a hybridized vehicle propulsion system. It draws on a successful earlier study which showed a non-compounded opposed-piston engine to be clearly superior to other forms of 2-stroke engine, such as the widely adopted uniflow-scavenged poppet valve configuration. Electrical power transmission is proposed as the method of providing the necessary variable-speed drive to transmit excess turbine power to the system energy storage medium. The work employs one-dimensional engine simulation on a single-cylinder basis, using brake specific fuel consumption (BSFC) as the reportable metric, coupled with positive or negative power flow to the engine from the compounder; this is a variation on an approach successfully used in earlier work. Here it shows the sensitivities of the overall system to cylinder pressure, the compressor and turbine efficiencies, exhaust backpressure and also provides a means to investigate the effect of the power transmission efficiency on the overall benefit. Reheating the air before the turbine is also investigated as a means of providing a “burst” performance facility, albeit at the expense of extra fuel consumption. Positive compounding work is shown to be achievable across all investigated engine operating points under certain conditions. Operating points at lower engine speeds showed an increased propensity for turbocompounding, with 5-6% of the brake torque arising from the compounder, compared to those at higher engine speeds, where a maximum of 4% was seen. BSFC was found to be highly dependent on compounding torque with improvements only arising from reducing backpressure. A better understanding of the flow restrictions of the exhaust aftertreatment and muffler systems, for a given application, would allow for more accurate determination of the possibility for BSFC reduction within realistic operating conditions.

This paper aims to correlate the in-cylinder soot formation and the exhaust particle emissions for different methods of gasoline/ethanol fueling in spark ignition engine. In particular, the engine was fueled with gasoline and ethanol separately and not, in this latter case both blended (E30) and dual fueled (EDF). For E30 the bend was direct injected and for EDF, the ethanol was injected in the combustion chamber and the gasoline into the intake duct. For both the injection configurations, the same percentage of ethanol in gasoline was supplied: 30%v/v. The measurements were carried out at 2000 and 4000 rpm, under full load, and stoichiometric condition, in small single cylinder optical engine. 2D-digital imaging was performed to follow the combustion process with a high spatial and temporal resolution through a full-bore optical piston. The two-color pyrometry was applied for the analysis of the in cylinder soot formation in the combustion chamber. Particle mass concentration was evaluated at the exhaust by means of a smoke meter. The particle size distribution function was measured in the range from 5.6 to 560 nm by an Engine Exhaust Particle Sizer (EEPS). It was observed that the use of ethanol allows the reduction of soot formation and particles emission in DI configuration. However, for E30 the in-cylinder soot formation and emissions are larger than EDF. This result is mainly due to the different contribution of gasoline. Optical analysis shows that in E30 the direct injected gasoline causes wide diffusive flames where soot formation is promoted; whereas for EDF the better evaporation and mixing of gasoline, typical of PFI configuration, results in few, small, and localized diffusive flames producing smaller particle emissions.

The increased limitations to both NOx and soot emissions have pushed engine researchers to rediscover gasoline engines. Among the many technologies and strategies, gasoline direct injection plays a key-role for improving fuel economy and engine performance. The paper aims to investigate an extremely complex task such as the idle operating engine condition when the engine runs at very low engine speeds and low engine loads and during the warm-up. Due to the low injection pressure and to the null contribution of the turbocharger, the engine condition is far from the standard points of investigation. Taking into account the warm-up engine condition, the analyses are performed with a temperature of the coolant of 50°C. The paper reports part of a combined numerical and experimental synergic activity aiming at the understanding of the physics of spray/wall interaction within the combustion chamber and particular care is used for air/fuel mixing and the combustion process analyses. In order to properly describe the engine condition, different injection strategies are investigated. Late and early injection strategies are deeply analyzed and compared in terms of combustion stability and pollutant emissions. UV-visible imaging and spectral measurements are carried out in real engine with wide optical accesses... Measurements are performed in the optically accessible combustion chamber realized by modifying a real engine. The cylinder head was modified in order to allow in the fourth cylinder the visualization of the fuel injection and the combustion process with high spatial and temporal resolution. The 3D-CFD engine simulations are reproduced by means the commercial code Star-CD. Due to the warm-up condition and the many physical sub-models a numerical methodology is implemented and particular care is used to boundaries conditions analyses. CFD analysis is used to find a possible explanation of the high cycle to cycle variability. The experimental and numerical comparisons, in terms fuel mixing and front flame propagation, give an explanation of the idle condition.

This paper was commissioned for the design and analysis of an entire rear suspension system befitting a Formula Society of Automotive Engineers (FSAE) vehicle. The paper includes a literature review to gain a full understanding of the workings and design decisions applied to the rear suspension in the Society of Automotive Engineers (SAE) competition. After completing the design development process, a final analysis of the designed system was done to ensure the minimum two years-of-life requirement is met. It was found that due to constraints, a major design change was necessary that involves mounting the A-arms further forward on the chassis body than previous generation vehicles. This design increased the stresses present in the system compared to previous designs. As such, careful consid-eration had been given to the analysis aspect of the paper. Full fatigue analysis performed individually on each component proved that the lower A-arm was the most critical component, with a predicted failure at 1466 laps. However, with the given lifespan of two years, this design procured a conservative Factor of Safety of above two years.Notable mention should be given to the complete develop-ment of an FSAE uniaxial force determination code that was produced by Team Recoil. This code greatly improved the confidence in component forces and thus allowed less conservative design choices in several other aspects.

This paper conceptualizes the design of a single-seater All-Terrain Vehicle (ATV). The aim was to design and fabricate a lightweight, high strength vehicle (under 175kgs) which can withstand harsh terrains, while being affordable and easily manufacturable. This paper covers the extent of design and simulations ranging from static structural, fatigue analysis, explicit dynamics etc. have been carried out. Tools such as SolidWorks, Ansys and MATLAB have been used throughout the process.The report is divided into individual subsystems, such as Chassis, Braking, Powertrain, Suspension and Steering. All the design considerations and objectives of each of the subsystems have been included. Simulation results of various components such as the Chassis, A-arms, Knuckles, Hubs and integral mounts have been attached with focus on modelling based on real-time forces and behaviors.

This paper describes a multi-degree-of-freedom model of a three-wheeled car, implemented in Matlab®. The purpose was to investigate the dynamics of the car (assumed to be rigid on its suspension) during cornering. While the problems associated with three-wheeled cars are well-known, much of the guidance in the literature and off-the-software assumes a conventional four-wheeled car. Consequently, the authors were approached with a battery-electric concept car which was thought to offer better performance than existing variants, because the use of hub motors lowered the centre of gravity and hence reduced rollover coefficient. However, simulation of the vehicle model in cornering shows that the concept is still prone to instability. Indeed, it suffers greater roll velocities than a comparable three-wheeled car with internal combustion engine, because the ratio of sprung to unsprung mass is significantly altered. This paper therefore recommends a programme of further simulations and model-based design changes to progress the concept to a marketable performance product.

The automotive trends of vehicles with lower aerodynamic drag and more powerful drivetrains have caused increasing concern regarding stability issues at high speeds, since more streamlined bodies show greater sensitivity to crosswinds. This is especially pronounced for high vehicles, such as sports utility vehicles. Besides, the competitiveness in the automotive industry requires faster development times and, thus, a need to evaluate the high speed stability performance in an early design phase, preferable using simulation tools. The usefulness of these simulation tools partly relies on realistic boundary conditions for the wind and quantitative measures for assessing stability without the subjective evaluation of experienced drivers. This study employs an on-road experimental measurements setup to define relevant wind conditions and to find an objective methodology to evaluate high speed stability. The paper focuses on the events in proximity to the drivers’ subjective triggers of instability. Wind direction and magnitude, vehicle motion response, along with the subjective event triggering were measured at different conditions of the natural wind. A statistical approach was utilized to analyze the correlation between the vehicle response and subjective triggers together with the wind conditions. A correlation was established between the subjective triggers and a rapid change in lateral acceleration and yaw velocity response. The paper also proposes a set of four crosswind gust profiles of interest for driving stability, combining results from previous research and the experimental data of the natural wind obtained in this study. These findings can be used as objective measures for virtually assessing stability performance and as realistic boundary conditions for simulating wind gusts.

Today, the contribution of the transportation sector on greenhouse gases is evident. The fast consumption of fossil fuels and its impact on the environment have given a strong impetus to the development of vehicles with better fuel economy. Hybrid electric vehicles fit into this context with different targets, starting from the reduction of emissions and fuel consumption, but also for performance and comfort enhancement. Lamborghini has recently invested in the development of a hybrid super sport car, due to performance and comfort reasons. Aventador series gearbox is an Independent Shift Rod gearbox with a single clutch and during gear shifts, as all the single clutch gearbox do, it generates a torque gap. To avoid the additional weight of a Dual Clutch Transmission, a 48V Electric Motor has been connected to the wheels, in a P3 configuration, to fill the torque gap, and to habilitate regenerative braking and electric boost functions. This paper discusses the usage of a control-oriented vehicle and powertrain model to analyze the performance of the first Lithium Ion Capacitor-based hybrid V12 by Automobili Lamborghini. The internal combustion engine, the gearbox, the LiC and the vehicle longitudinal dynamics models have been initially validated through the comparison with experimental data from chassis dynamometer testing, in addition to experimental results from specific components' testing. As shown in the paper, the validated model has then been used to develop control strategies aimed at increasing comfort and performance, but also to expand the hybrid system capabilities by widening the LiC working range, and to study the possibility of implementing CO2 reduction-oriented control functions.

Connected vehicles (CVs) have situational awareness that can be exploited for control and optimization of the powertrain system. While extensive studies have been carried out for energy efficiency improvement of CVs via eco-driving and planning, the implication of such technologies on the thermal responses of CVs has not been fully investigated. One of the key challenges in leveraging connectivity for optimization-based thermal management of CVs is the relatively slow thermal dynamics, which necessitate the use of a long prediction horizon to achieve the best performance. Long-term prediction of the CV speed, unlike the V2V/V2I-based short-range prediction, is difficult and error-prone. The multiple timescales inherent to power and thermal systems call for a variable timescale optimization framework with access to short- and long-term vehicle speed preview. To this end, a model predictive controller (MPC) with a multi-range speed preview for integrated power and thermal management (iPTM) of connected hybrid electric vehicles (HEVs) is presented in this paper. The MPC is formulated to manage the power-split between the engine and the battery while enforcing the power and thermal (engine coolant and catalytic converter temperatures) constraints. The MPC exploits prediction and optimization over a shorter receding horizon and longer shrinking horizon. Over the longer shrinking horizon, the vehicle speed estimation is based on the data collected from the connected vehicles traveling on the same route as the ego-vehicle. Simulation results of applying the MPC over real-world urban driving cycles in Ann Arbor, MI are presented to demonstrate the effectiveness and fuel-saving potentials of the proposed iPTM strategy under the uncertainty associated with long-term predictions of the CV's speed., 15 pages, 15 figures, 1 table, to appear in 2020 WCX SAE World Congress Experience, SAE Technical Paper 2020-01-0590

International audience

The SAE G-27 committee was tasked by ICAO to develop a performance-based packaging standard for lithium batteries transported as cargo on aircraft. The standard details test criteria to qualify packages of lithium batteries & cells for transportation as cargo on-board passenger aircraft. Lithium batteries and cells have been prohibited from shipment as cargo on passenger aircraft since 2016. This paper summarizes the results of the tests conducted by Transport Canada and National Research Council Canada to support the development of this standard with evidence-based recommendations. It includes a description of the test specimens, the test set up, instrumentation used, and test procedures following the standard as drafted to date. The study considered several lithium-ion battery and cell chemistries that were tested under various proposed testing scenarios in the draft standard. The aim was to assess the feasibility of proposed tests, and to determine whether the tests are able to accurately capture hazards which may arise from a catastrophic battery or a cell failure within the package. Laboratory results were also simulated with Computational Fluid Dynamics software for confirmation. A comprehensive study involved validating several areas of the draft standard: i) the baseline test method consisting of a package of lithium cells; ii) an oversized battery (i.e. electric vehicle battery) to large to be tested within the proposed test chamber; iii) stratification of evolved gases within the test chamber; iv) control thermocouple placement location on the test cell for compliant measurement; and, v) test chamber leak rate effect on vented gas ignition. The main findings of the experiments are presented in this paper for each test scenario as prescribed in the draft standard; results for proposed recommendations to improve the standard to identify a hazard with higher accuracy are presented. A discussion on each of the recommendations is included., AeroTech, March 17-20, 2020

The dual-fuel (diesel/natural gas, NG) concept represents a solution to reduce emissions from diesel engines by using natural gas as an alternative fuel. As well known, the dual-fuel technology has the potential to offer significant improvements in the emissions of carbon dioxide from light-duty compression ignition engines. A further important requirement of the DF operation in automotive engines is a satisfactory response in a wide range of load levels. In particular, the part-load levels could present more challenging conditions for an efficient combustion development, due to the poor fuel/air ratio. Basing on the above assumptions, the authors discuss in this article the results of a combined numerical and experimental study on the effect of different injection timings on performance and pollutant fractions of a common rail diesel engine supplied with natural gas and diesel oil. The study of dual-fuel engines that is carried out in this paper aims at the evaluation of the CFD capability to analyze the main phenomena that characterize this particular technology. Actually, in order to put into evidence the key processes that take place during the dual-fuel operation, say the typical flame propagation throughout the premixed methane-air medium that is activated by the early self-ignition of the diesel fuel, the fluiddynamic calculations are extremely useful. The different conditions have been induced by changes in the operating parameter setting; in particular, the tests have been performed by varying the injection timing for a fixed NG ratio, both at full and at part load. Actually, the start of the liquid fuel injection can considerably influence the combustion development and therefore THC and NOx fractions production. The calculations have been validated with the experimental data and a comparison between diesel and dual fuel diesel/CNG operation has been made, in terms of performance and pollutant levels. A detailed description of the phenomena that govern the engine response at several operating conditions and at different load levels is then provided.

The use of direct injection (DI) engines allows a more precise control of the air-fuel ratio, an improvement of fuel economy, and a reduction of exhaust emissions thanks to the ultra-lean combustion due to the charge stratification. These effects can be partially obtained also with an optimized Air Direct Injection that permits to increase the turbulence at low speed and load increasing the combustion stability especially in lean condition. In this paper, a gasoline PFI (named G-PFI), gasoline PFI-methane DI dual fuel (named G-MDF) lean combustion were analyzed. The G-MDF configuration was also compared with a gasoline PFI - air DI (named G-A) configuration in order to distinguish the chemical effect of methane from the direct injection physical effect. The tests were carried out in a small displacement PFI/DI SI engine. The experimental investigation was carried out in a transparent small single-cylinder, spark ignition four-stroke engine. It was equipped with the cylinder head of a Direct Injection 244 cc engine. The in-cylinder pressure was measured and the indicated mean effective pressure, IMEP, and its CoV were evaluated. 2D-digital imaging optical measurements were performed to analyze the combustion process with high spatial and temporal resolution. In particular, it allows to follow the flame evolution and evaluate the flame front propagation speed. The CO, CO2, HC and NOx emissions were characterized at the exhaust by means of gaseous analyzers. The measurements were performed at 2000 rpm PL in steady state condition. The G-MDF as well as the G-A configurations allow improving the vaporization of the heavy gasoline compound and the homogenization of the charge. Moreover, for the G-MDF, the presence of the methane and its chemical interaction with gasoline heavy hydrocarbon enhances a more efficient combustion

This paper presents an optimization algorithm, based on discrete dynamic programming, that aims to find the optimal control inputs both for energy and thermal management control strategies of a Plug-in Hybrid Electric Vehicle, in order to minimize the energy consumption over a given driving mission. The chosen vehicle has a complex P1-P4 architecture, with two electrical machines on the front axle and an additional one directly coupled with the engine, on the rear axle. In the first section, the algorithm structure is presented, including the cost-function definition, the disturbances, the state variables and the control variables chosen for the optimal control problem formulation. The second section reports the simplified quasi-static analytical model of the powertrain, which has been used for backward optimization. For this purpose, only the vehicle longitudinal dynamics have been considered. The third section describes the Model-in-the-Loop environment of the vehicle, implemented in Simulink. In particular, the validation of the fuel consumption and the battery temperature models against experimental data is shown, and the original control strategies for the energy and thermal management are described, as well. This powertrain model is used to evaluate vehicle performance. As the powertrain architecture offers different torque split possibilities, different approaches to the powertrain control are considered, starting from the baseline rule-based controllers for both the thermal and energy management, to the combined-optimization based controllers. This paper shows a consistent fuel economy improvement due to energy management optimization, which becomes even larger if thermal management is included in the optimization algorithm.

Syngas produced from biomass gasification is being increasingly considered as a promising alternative to traditional fuels in Spark-Ignition (SI) Internal Combustion Engines (ICEs). Due to the low energy density and extreme variability in the composition of this gaseous fuel, numerical modeling can give an important contribution to assure stable engine performances. The present work intends to give a contribution in this sense in this sense, by proposing a multi-level set of approaches, characterized by an increasing detail, as a tool aimed at the optimization of energy conversion of non-conventional fuels. At first, a specific characterization of the dependency of the syngas laminar flame speed upon its composition is achieved through an iterative approach pursued in the ANSYS ChemkinTM environment, where validated correlations of the flame speed tuning parameters are obtained in a zero-dimensional framework. Subsequently, the interaction between combustion kinetics and fluid dynamics is considered through the development of a mono-dimensional (1D) model of the whole engine system in the GT-Power environment. A predictive combustion model, tuned on the ground of the combustion parameters determined through the previous approach, is implemented to guarantee the correct prediction of the engine efficiencies as the primary energy related to the gaseous fuel composition varies. At last, a 3D Computational Fluid Dynamics (CFD) model is developed within the AVL FIRETM software to reproduce the engine combustion cycle within a Reynolds Averaged Navier Stokes (RANS) schematization. The detailed chemical reaction mechanism GRI-Mech 3.0 is used to give details about the syngas oxidation chain. All the numerical results are validated with respect to literature data as regards the laminar flame speed prediction, and by using experimental measurements under real operation and syngas generation through biomass gasification, as concerns the engine performances. The proposed multi-level analysis is proposed as a robust procedure suitable of fully accounting of the overall variability that characterizes the gaseous fuel as the biomass composition and operative conditions are varied.

Increasingly stringent regulations in the field of pollutant are forcing engine manufacturers to adopt new solutions to contain exhaust emissions, such as Hybrid Electric Vehicles (HEV) or Full Electric Vehicles (FEV). Still far from the wide diffusion of FEV limited from electrochemical storage systems together with the difficulty of creating adequate infrastructure distributed throughout the territory to recharging batteries, the HEV seems to be actually a better solution. The hybrid vehicle is already able to guarantee satisfactory autonomy and low pollution levels by combining the advantages offered by the two technologies of thermal and electric propulsion. Currently on the market there are several types of hybrid vehicles, with different degree of hybridization (electric motor power versus propulsion total power), capacity to store electricity and type of scheme constructive adopted for the integration between the thermal engine and the electric machine. A particular interest is getting the mild-hybrid (or light hybridization) and the micro-hybrid (or minimum hybridization) with 48V electrical system added to the classic 12V one. A possible solution could be the electric turbo-compounding system where a turbine coupled to a generator (turbo-generator) uses the exhaust gas flow of a reciprocating engine to harvest waste heat energy and convert it into electrical power. In this way, the power generated from the system can be used to feed local electrical loads such as engine auxiliaries, increasing the whole system efficiency. The present study deals with the simulation of a spark ignition engine, present in a test room of Istituto Motori (CNR), including a turbo-generator at the exhaust to evaluate the advantages in terms of overall efficiency. The internal combustion engine model was developed by using a 1D code (GT-Power software), while the turbo-generator and the electric system are described in the Matlab/Simulink environment. The results obtained showed an appreciable increase in the overall efficiency.

The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off "CO2-system cost" in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO2-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles. In this framework, a comprehensive approach covering the whole powertrain is of primary importance in order to simultaneously meet the performance, efficiency, noise and emission targets, and therefore, further development of the combustion system design and injection system represent important levers for additional improvements. For this purpose, a dedicated 0.5 dm3 single-cylinder engine has been developed and equipped with, a state-of-the-art Euro 6 combustion system, and an advanced common rail fuel injection system (FIS) offering higher flexibility in terms of injection strategy and higher quantity accuracy. Three injector nozzles with different hydraulic flow rates (HF) have been selected and employed for the overall combustion process optimization. The optimization has been performed by means of an extensive DoE-based test campaign in which the engine and FIS operating parameters have been parametrized with the aim to carry out a proper combination in terms of HF and injection strategy. The results at partial load conditions evidence significant advantages in applying an advanced injection pattern, while the HF reduction can significantly improve the smoke emission and combustion noise without fuel consumption penalties. Therefore, a proper combination and optimization of the HF and injection strategy can provide low noise and engine-out smoke while maintaining the rated power performance targets.

Internal combustion (IC) engine exhaust system can influence the engine's performance in a significant way. This paper shows that a variable exhaust manifold runner length can improve the engine performance in terms of its output torque by over 10% especially at lower engine speed. Similarly, other exhaust systems such as valve timing and valve lift can improve the performance of the engine in different magnitudes. But when smaller improvements are clubbed together, a significant improvement can be achieved. This paper researches first the exhaust runner length on the engine's performance. Then, the exhaust valve timing is adjusted to further improve the engine torque produced for the exhaust runner lengths analyzed. Study of a combined effect showed that the runner length requirement shifts slightly as the valve timing is changed. Due to practical limitations foreseen in having longer runner lengths and limitations in the rate of runner length variation, certain areas have to undergo through a region where the torque values are as low as they can be. Though this happens in every single exhaust system out in the market today, valve lift is be used to compensate this loss. In this research the engine torque loss at these points can be regained by 50% by taking the benefit of a variable exhaust valve timing and valve lift system. The combined effect of changing runner length, valve timing and valve lift yields improvements in torques of 2-3% and 7-10% at higher and lower engine speeds, respectively Refereed/Peer-reviewed

The double compression-expansion engine concepts (DCEE) are split-cycle concepts where the compression, combustion, expansion and gas exchange strokes occur in two or more different cylinders. Previous simulation studies reveal there is a potential to improve brake efficiency with these engine concepts due to improved thermodynamic and mechanical efficiencies. As a continuation of this project this paper studies an alternative layout of the DCEE-concept. The concept studied in this paper has three different cylinders, a compression, a combustion and an expansion cylinder. Overall system indicated and brake efficiency estimations were based on both engine experiments and simulations. The engine experiments were carried out at 10 different operating points and 5 fuelling rates (between 98.2 and 310.4 mg/cycle injection mass) at an engine speed of 1200 rpm. The inlet manifold pressure was varied between 3 and 5 bar. Due to concerns with structural stability the peak cylinder pressure during the engine experiments was limited to 210 bar. Exhaust backpressure was limited to 8 bar due to thermal stress on the exhaust valves. The engine experiments reveal that a gross indicated efficiency (GIE) of 47 % is achieved at most of the operating points. There were cases where GIE was below 45 % due to high heat loss and degraded combustion efficiency.The data obtained from the engine experiments were then used as input into the full DCEE-engine simulations. System brake efficiency was determined by estimating friction loss in the simulations. These simulations and friction estimations suggests a system brake efficiency of 41.8 % at the lowest fuelling rate (98.2 mg/cycle) is achieved. Increasing engine load improves efficiency due to lower relative intercooling loss and improved mechanical efficiency. A peak system brake efficiency of 52.8 % is achieved at a very high injection mass (275.6 mg/cycle) and 5 bar Pinlet setting. A further increase in injection mass to 310.4 mg/cycle results in a high increase in heat loss which causes system brake efficiency to decrease to 49.9 %. (Less)

All Rights Reserved. Modelling is widely used for the development of hybrid electric vehicle (HEV) powertrain technologies, since it can provide accurate prediction of fuel consumption and COâ emissions, for a fraction of the resources required in experiments. For comparison of different technologies or powertrain parameters, the results should be accurate relative to each other, since powertrains are simulated under identical model details and simulation parameters. However, when COâ emissions of a vehicle model are simulated under a driving cycle, significant deviances may occur between actual tests and simulation results, compromising the integrity of simulations. Therefore, this paper investigates the effects of certain modelling and simulation parameters on COâ emission results, for a parallel HEV under three driving cycles (NEDC, WLTC and RTS95 to simulate real driving emissions (RDE)). A sensitivity analysis on battery state of charge levels (SOC), control systems, component data resolutions, warm-up phase, time-step, driver controller behavior and 0D vs 1D simulation parameters is carried out and their effect on COâ emission results are investigated. While any change in one of the parameters may result in either a lower or higher COâ value, their cumulative effect on simulation results may result in significant differences of up to +-15%. Unfortunately, it is not hard to overlook the effect of these parameters and conduct powertrain simulations without taking this into account. By identifying key parameters and quantifying their effect on simulation results, this paper aims to improve the accuracy of HEV powertrain simulations to provide more reliable results.

This paper investigates abnormal combustion during the cranking phase of spark-ignition small engines, specifically the occurrence of backfire at the release of the starter motor during kickback. The research focusses on the influence of fuel composition, mainly in terms of ethanol percentage, on backfire occurrence. Interest in this abnormal combustion is growing due to the increased use of fuels with different chemicalphysical properties with respect to gasoline. Moreover, this issue will become even more topical due to the implementation of simple control and fuel supply systems on low cost-engines, which are widely used in developing countries. Experimentation was carried out in an optically accessible engine derived from a 4-stroke spark ignition engine for two-wheel vehicles. The test bench was instrumented and adapted in order to simulate the engine conditions that lead to anomalous ignition in the intake duct (backfire) during the reverse rotation of the engine (kickback). Two different test procedures were developed with the aim of promoting the ignition at the intake. Major engine parameters were measured, such as the incylinder pressure, the pressure at the exhaust and at the intake; in order to characterize the engine conditions and to monitor the ignition in the intake manifold. Furthermore, an optical investigation of the combustion chamber was performed using high spatial and temporal resolution measurements. Engine and optical data were correlated and the analysis allowed characterization of backfire during kick-back, enabling identification of the conditions that make backfire more probable and to observe the influence of fuel composition

The growing concerns over the pollutant emissions as well as the depletion of fossil fuel led to the research of advanced combustion mode and alternative fuels for the reduction both of fuel consumption and exhaust emissions. The dual-fuel injection system can be used to improve the engine performance and reduce the fossil fuel consumption performing simultaneously a direct-injection (DI) and a port-fuel-injection (PFI) of different fuels. Ethanol is one of the most promising alternative fuels for SI engines. It offers high anti-knock quality because of the high octane number; moreover, being an oxygenated fuel is very effective in particle emissions reduction. On the other hand, it is characterized by lower energy density mainly because of the low lower heating value (LHV). The aim of the paper is the investigation of the ethanolgasoline dual fuel combustion on engine performance and emissions. The experimental activity was carried out in a single cylinder engine for two wheel vehicles with a displacement of 250 cc. It was equipped with a prototype gasoline direct injection (GDI) head and with an injector in the intake manifold. This makes it possible to run in dual fuel mode performing a direct injection of ethanol and a port fuel injection of gasoline. This configuration was chosen in order to reduce the particle emissions typical of GDI engines. The tests were carried out at engine operating points representative of the typical urban driving conditions: 2000 rpm, 4000 rpm and 5000 rpm full load. The in-cylinder pressure was measured by means of a quartz pressure transducer flush-mounted in the region between intake and exhaust valves. The gaseous emissions and particle concentration were measured at the exhaust by means of a gas analyzer and a smoke meter. Particle size distribution function was measured in the range from 5.6 nm to 560 nm by means of an Engine Exhaust Particle Sizer (EEPS).

The paper deals with experimental testing of a natural gas fueled engine. Break Specific fuel Consumption (BSFC), Average Mass Flow Rate, Instantaneous Cylinder Pressure and some wall temperatures have been measured at some full and part load operating conditions. The results of this experimental activity, still in progress, have been used to calibrate a 1D-flow engine’s model. Then the effects of some VVA strategies have been theoretically studied through the validated model. With the aim of maximizing the full load engine’s torque, a genetic algorithm was used to calculate the optimized intake and exhaust valves timing angles. Various VVA strategies were compared at part-load in order to reduce brake specific fuel consumption.

Enhanced calibration strategies and innovative engine combustion technologies are required to meet the new limits on exhaust gas emissions enforced in the field of marine propulsion and on-board energy production. The goal of the paper is to optimize the control parameters of a 4.2 dm3 unit displacement marine DI Diesel engine, in order to enhance the efficiency of the combustion system and reduce engine out emissions. The investigation is carried out by means of experimental tests and CFD simulations. For a better control of the testing conditions, the experimental activity is performed on a single cylinder prototype, while the engine test bench is specifically designed to simulate different levels of boosting. The numerical investigations are carried out using a set of different CFD tools: GT-Power for the engine cycle analysis, STAR-CD for the study of the in-cylinder flow, and a customized version of the KIVA-3V code for combustion. All the models are calibrated through the above mentioned experimental campaign. Then, CFD simulations are applied to optimize the injection parameters and to explore the potential of the Miller combustion concept. It is found that the reduction of the charge temperature, ensuing the adoption of an early intake valve closing strategy, strongly affects combustion. With a proper valve actuation strategy, an increase of boost pressure and an optimized injection advance, a 40% reduction of NOx emissions can be obtained, along with a significant reduction of in-cylinder peak pressure, without penalizing fuel efficiency.

In this paper some results relative to tests performed on road with a Fiat Panda Bipower, (CNG and gasoline powered), and a New Panda Twin Air with auto Start & Stop system, are presented. Gaseous emissions are measured with Portable Emission Measurement Systems (PEMS) on two different urban routes, in terms of traffic and slope characteristics during in use experiments. PEMS testing offers an easy and efficient way to evaluate the vehicle emissions over a huge variety of conditions and provides us a direct way to study the in-use emissions of combustion engines, when you want to verify the effect of the traffic and of a particular device on fuel economy and emissions reduction. Moreover now PEMS performances are very comparable to those obtained by standard laboratory instrumentation systems. Instrumentation installed on board for the measurement of gaseous emissions is a Semtech analyzer coupled with an exhaust flow meter; also vehicle position is individuated (from GPS) and engine parameters (via ECU or CAN) are registered at 1Hz. The aims of this activity are to compare fuel consumptions and emissions on road during real world experimental tests, in order to identify and characterize representative road routes. The tests were carried out on different routes of the city of Naples: Route A, an area mostly plane, and Route B, in which orography changes suddenly in slope. Each trip realized by vehicles is subdivided in kinematic sequences and the vehicle emissions and fuel consumption are analyzed and presented as value on each kinematic sequence. The kinematic sequence is the part of motion of the vehicle between two successive stops. Having to take into account the evolution of the vehicle operating conditions, a sequence must be characterized by a number of variables. So statistical methods are necessary to interpret and to correlate emission and fuel consumption results. In the first phase tests with the Twin Air were driven by switching off the Start & Stop system. Then the tests with this car were repeated on the same routes (A forward / back and B) activating the Start & Stop. So the objective is to compare the measurements made with and without the start-stop functionality and on the two paths. Moreover, the results are also compared with those obtained by the other car Fiat Panda Bipower, (gasoline powered) on the two routes. Different types of comparison of vehicle emissions and fuel economy in different driving conditions and with or without a specific device, allows us to better have insight into the variability of emission behavior of a vehicle in real use.

Within the context of distributed power generation, small size systems driven by spark ignition engines represent a valid and user-friendly choice, that ensures good fuel flexibility. One issue is that such applications are run at part load for extensive periods, thus lowering fuel economy. Employing an inverter (fitted between the generator and load) allows engine operation within a wide range of crankshaft rotational velocity, therefore improving efficiency. For the purpose of evaluating the benefits of this technology within a co-generation framework, two configurations were modeled by using the GT-Power simulation software. After model calibration based on measurements on a small size engine for two-wheel applications, the downsized version was compared to a larger power unit operated at constant engine speed for a scenario that featured up to 10 kW rated power. Indeed, the downsizing concept was found to ensure an electrical efficiency improvement of around 10% at 50% load, over 30% at 20% load, and reduced fuel consumption by over 50% at lower load. The co-generation potential was also evaluated, and it resulted practically the same from full to 50% load, while at low load the larger engine featured heat recovery potential up to two times larger compared to the smaller unit.

In recent years, the More-Electric Aircraft (MEA) concept has undergone significant development and refinement, striving towards the attainment of reductions in noise and CO2 emissions, increased power transmission efficiency and improved reliability under a range of flight scenarios. The More-Electric Engine (MEE) is increasingly being seen as a key complementary system to the MEA. With this concept, conventional engine auxiliary systems (i.e. fuel pumps, oil pumps, actuators) will be replaced by electrically-driven equivalents, providing even greater scope for the combined aircraft and engine electrical power system optimisation and management. This concept, coupled with extraction of electrical power from multiple engine spools also has the potential to deliver significant fuel burn savings. To date, single or dual channel electrical power generation and distribution systems have been used in engines and aircrafts. However, with the increasing electrification of flight-critical engine auxiliaries along with the requirement for greater load transfer flexibility, a three-channel architecture should be considered. This paper investigates potential concepts for a three-channel power system architecture in an MEE system. The paper considers issues such as architecture layout and key technologies that may be considered for MEE architecture. Using an extensive database of public domain MEA/MEE power system component failure rates, a detailed fault tree analysis is then presented. This provides a quantitative comparison of dual channel and three-channel architecture candidates under the pertinent failure modes as well as showing the impact of common architecture features on system reliability and robustness. Finally, the paper concludes with a discussion of the ring busbar topology operation and power electronics technology requirements that could successfully implement a flexible and robust three-channel architecture for MEE systems.

Look ahead information can be used to improve the powertrain’s fuel consumption while efficiently controlling exhaust emissions. A passenger car propelled by a Euro 6d capable diesel engine is studied. In the conventional approach, the diesel powertrain subsystem control is rule based. It uses no information of future load requests but is operated with the objective of low engine out exhaust emission species until the Exhaust After-Treatment System (EATS) light off has occurred, even if fuel economy is compromised greatly. Upon EATS light off, the engine is operated more fuel efficiently since the EATS system is able to treat emissions effectively. This paper presents a supervisory control structure with the intended purpose to operate the complete powertrain using a minimum of fuel while improving the robustness of exhaust emissions. A supervisory controller assisted by look ahead information, and using a supervisory control interface that works in concert with low level local controllers, can make subsystems operate near optimal. The look ahead parametrized supervisory control calculates the set-points for the subsystems: Internal Combustion Engine (ICE), Lean NOx Trap (LNT) and the Selective Catalytic Reduction (SCR) based on the Emission Equivalent Fuel Consumption minimization strategy (EEFC). The controller performance is analyzed for the World wide harmonized Light vehicles Test Cycle (WLTC) and randomly sequenced WLTCs under different initial conditions. This paper extends upon the earlier work where an LNT-SCR EATS supervisory control structure was proposed that optimizes based on the EEFC strategy. The future work will focus on extending the approach to more subsystems and characterizing the look ahead information.