Search

The Life Cycle Assessment (LCA) of asphalt pavements are associated with significant uncertainty resulting from variability in the quantity and impact of individual components, the quality of data for each component, and variability of asphalt durability. This study presents a framework to quantify and incorporate the uncertainty of LCA and asphalt durability data into LCA of asphalt surfacings. The suggested framework includes: estimating the uncertainty of asphalt production processes by the pedigree matrix method, conducting a deterministic LCA, applying Monte Carlo Simulation (MCS) to estimate the probability density functions (PDFs) of the considered impacts using the uncertainty data, deterministic solution, and asphalt durability. This framework was applied to six asphalt mixtures; the results show that there is significant uncertainty in the processes that contribute to the environmental impacts. They also showed that considering asphalt durability and its uncertainty is critical and can significantly change the results and interpretation of LCA.

ABSTRACTThe binder content of rubberised asphalt mixtures is usually increased compared to that used in conventional asphalt. This increase is deemed important to compensate for the reduction in the actual bitumen due to the existence of rubber particles. This study presents the results of performance evaluation conducted on different rubberised Stone Mastic Asphalt (SMA) mixtures produced using different types and contents of rubberised bitumen. The energy ratio (ER) computed from Superpave Indirect Tensile (IDT) tests was used to evaluate the cracking resistance of asphalt mixtures while the rutting behaviour was evaluated using the Repeated Load Axial Test (RLAT). The indirect tensile stiffness and strength were used to evaluate the moisture susceptibility. Using the same binder content for rubberised SMA mixtures as used in the conventional mixtures can still give superior performance properties. Adding crumb rubber to softer base bitumen can produce asphalt mixtures with superior cracking and rutting resistance.

ABSTRACTInter-laboratory experiments were designed to evaluate the impact of plastic waste blended directly in bitumen and to assess the properties, using conventional and advanced bituminous binder testing. The blends targeted 5% of plastic waste in 95% bitumen, using two types of polyethylene (PE) primary (pellets) and secondary (shreds) waste. The experiments showed that the addition of PE waste to bitumen does not alter the chemistry of the bitumen, the blending is physical. The DSR results indicate a strong dependency on the testing temperature as at low temperatures the composite material bitumen and PE behave both elastically whereas, at higher temperatures, the bitumen becomes viscoelastic. The MSCR tests indicated that the neat binder is more sensitive to permanent deformation compared to the blends with PE. The fatigue performance using the Linear Amplitude Sweep test showed a better performance in terms of stress and fatigue life for the PE blends.

The tire rubber obtained from end-of-life car and truck tires has been successfully recycled, among other applications, in the asphalt industry by providing a mean to get asphalt mixtures with superior performance. Textile fibres are another component derived from tire recycling typically disposed of in landfills or used in energetic valorisation. This paper wants to re-ignite interest in this secondary product by evaluating its use as a valuable resource in asphalt mixtures. Indirect tensile tests, dynamic modulus, fatigue resistance, and permanent deformation tests were performed on a series of AC14 asphalt mixtures manufactured with two binders, namely 50/70 and 35/50 pen, using several binder and fibre contents. The results indicate that incorporating fibres of tire recycling is not problem-free. Results have shown that can be advisable in pavement applications whenever the investigated fibre-modified mixtures allowed to incorporate at least 6.5% binder content with great benefit for pavement performance.

Stone Mastic Asphalt (SMA) has been broadly used on heavily trafficked roads and motorways in the UK due to its known stability and durability. In this study, several sets of SMA mixtures were produced using different rubberised bitumens, including a Fischer–Tropsch wax pre-treated rubberised bitumen. Properties associated with rutting were evaluated using both linear and nonlinear viscoelastic analyses, using different test methods such as the Strategic Highway Research Programme (SHRP), Shenoy rutting parameter, zero shear viscosity (ZSV) and multiple stress creep recovery (MSCR) tests. The rutting resistance of the resulting SMA mixtures was assessed using the Repeated Load Axial Test (RLAT). The addition of rubber was expected to enhance rutting resistance of these materials. The results indicated that among the binder rutting parameters assessed, the non-recoverable creep compliance (Jnr) computed from the MSCR test, showed the best correlation with the rutting resistance of the corresponding asphalt mixtures. Finally, a more fundamental analysis was provided by assessing the conditions of binder films that would be experienced in the mixtures.HighlightsRutting resistance of binders and mixtures are well correlated when the realistic strain conditions are taken into accountSMA produced using rubberised bitumens resulted in highly rut resistant mixturesMSCR test can measure the rutting resistance of binders

An experimental study was conducted to evaluate the effectiveness of two bio-additives as rejuvenators on the properties of asphalt mixtures containing 50% RAP and their binder constituents containing 37% RAP binder. Before mixing, the rejuvenators were blended with fresh bitumen and the extracted and recovered RAP bitumen, and changes in the rheological properties of the binders were assessed using performance grading (PG) criteria. The results showed that both rejuvenators could improve the low-temperature performance of the aged RAP binder and restore its low-temperature properties. Master curves for the unaged, RTFO-aged, and PAV aged blends were constructed using both the Christensen-Anderson-Marasteanu (CAM) model and the Sigmoidal models. A comparative statistical analysis conducted on the models indicated no significant difference between the measured and predicted complex modulus values at any aging conditions. The pairwise statistical comparison between the two models showed that at unaged conditions, they can perfectly overlap as the p-values were greater than the level of significance. However, for the PAV-aged binders, this behaviour appears to weaken due to the brittle behaviour of the binders. Further statistical analyses revealed no significant differences between the two models at unaged conditions, however, as the binders where subjected to aging, significant differences between the two models began to appear. Mixing was performed in two locations: lab and plant, while compaction was performed only in the lab. After mixing and compaction, mixtures were evaluated for their stiffness characteristics through dynamic modulus testing. Compared to the control mixture, rejuvenated mixtures showed lower dynamic modulus values specially at high temperatures. A statistical comparison between the lab-produced, lab-compacted mixtures and plant-produced, lab compacted mixtures showed that both the rejuvenation and the location of mixing were significant factors in the stiffness measurements.

Using Reclaimed Asphalt (RA) in new asphalt mixtures can reduce the amount of new material required thereby saving money and natural resources. In addition, asphalt mixtures with RA have shown comparable properties and performance to that generally associated with asphalt mixtures made with 100% virgin material. However, RA content in pavement surface layers is still limited due to specification and technical limitations. For higher contents, the aged RA binder must be analysed to accurately determine the requirements for virgin binders and additives while the degree of blending (DOB) between the RA binder and the virgin binder also needs to be quantified. This is not a simple process and generally designers assume one of two opposing theories associated with 100% (full blending) or 0% (“Black Rock”) DOB. This paper proposes a new approach to estimate a unique property of the RA known as the Degree of Binder Activity (DoA) as a function of the processing temperatures of the RA. The study showed positive results and indicated that this DoA approach can be used as a tool to better understand RA in order to improve the binder/blend design for recycled asphalt mixtures.

The recent drive to find ways to increase sustainability and decrease costs in asphalt paving has led researchers to find innovative ways to incorporate more recycled materials and bio-derived binders into mixes with varying success. A new novel bio-derived binder made from refined pine chemistry stabilised with a polymer can increase the sustainability of asphalt mixes while maintaining pavement performance. Laboratory performance testing was conducted on asphalt mixes containing 50% Reclaimed Asphalt Pavement (RAP) by mix weight and the novel bio-derived binder. Results show that the bio-derived binder outperforms the conventional 50/70 pen grade binder mixes with respect to resistance to thermal cracking and adequately passes all requirements for pavements with 20-year design loadings of less than 30 million ESALs. This research shows that asphalt mixes containing 50% RAP and a bio-derived binder can be designed to pass performance criteria at low, intermediate, and high temperatures without the need of neat bitumen.

Polymer additives are widely used to improve the performance of road bitumens including their resistance to hardening during oxidation, although their oxidative inhibitor effect has not been well documented. This study aims to investigate the effect of laboratory-simulated ageing on the microstructure, and rheological properties of Polymer Modified Bitumens (PMBs) prepared with a Styrene-Butadiene-Styrene (SBS) copolymer and sulphur as a cross-linker. The laboratory ageing was conducted through the Rolling Thin Film Oven (RTFO) and the Pressure Aging Vessel (PAV) procedures. The unaged and aged binders were characterised using the Multiple Stress Creep and Recovery (MSCR) test, Gel Permeation Chromatography (GPC) and fluorescence microscopy. The MSCR test showed that the cross-linked polymer had a higher capability of mitigating the effect of bitumen hardening on the rheological response, while for the PMBs without cross-linking, the polymer effects decreased significantly after RTFOT ageing. The GPC results showed that the aromatics, resins and asphaltenes fractions of the unmodified bitumens shifted towards heavier molecules after one cycle of PAV ageing but showed limited variation with further ageing. Similar behaviour was observed for the uncross-linked polymer binders, while for the cross-linked polymer binder, the behaviour depended on the polymer concentration.

It is common practice to assume full blending of the aged binder of reclaimed asphalt (RA) within the design of new asphalt mixtures. Although being practical, this assumption has often led designers to asphalt mixtures lacking binder. Hence, going towards recycled asphalt mixtures (RAM) there is a need to have a better understanding of the blending phenomena, to have a general agreement on terminology and finally adapting RA classification and mix design procedures accordingly. This manuscript aims at being both a reference and stimulus for the scientific community to work in this direction and on this basis provides a nomenclature and a theoretical framework of the blending phenomena. The study is built upon a literature review on definitions, methods and influencing factors related with the blending phenomena and as a result, an intrinsic property of RA, the Degree of binder Activity (DoA), is introduced for the sake of improving RA classification. Furthermore, the two well-known concepts of the Degree of Blending (DoB) and the Degree of binder Availability (DoAv) are redefined, within the proposed framework, together with practical suggestions to introduce them in mix design procedures.

This paper investigates the effect of processing temperature and time on the rheological properties of recycled tyre rubber-modified bitumens (RTR-MBs) produced using two different base binders and an ambient ground crumb rubber modifier (CRM). The production of the RTR-MBs was accomplished by means of a standard Brookfield rotational viscometer together with a modified impeller, dual helical impeller, to allow mixing as well as real-time viscosity measurements of the produced RTR-MBs. The rheological properties of the final RTR-MBs were determined by means of standard dynamic mechanical analysis oscillatory and multiple stress creep recovery testing using a dynamic shear rheometer. The results indicate that the low processing conditions (160°C and 60 min) are not appropriate for developing RTR-MBs with enhanced physical and rheological properties. However, allowing the crumb rubber to interact with the base binder for longer mixing times (140 min) led to the development of an enhanced rubber (polymer) network structure within the blend (i.e. swelling of the CRM particles) and superior rheological properties. At the other extreme, using high-processing conditions (200°C and 140 min) led to RTR-MBs in which the rubber network had been subjected to devulcanisation and depolymerisation with a subsequent reduction in modification.