Search

A study of the dead layer thickness and quenching factor of a plastic scintillator for use in ultracold neutron (UCN) experiments is described. Alpha spectroscopy was used to determine the thickness of a thin surface dead layer to be 630 ± 110 nm. The relative light outputs from the decay of 241Am and Compton scattering of electrons were used to extract Birks' law coefficient, yielding a kB value of 0.087 ± 0.003 mm/MeV, consistent with some previous reports for other polystyrene-based scintillators. The results from these measurements are incorporated into the simulation to show that an energy threshold of (∼9 keV) can be achieved for the UCNProBe experiment. This low threshold enables high beta particle detection efficiency and the indirect measurement of UCN. The ability to make the scintillator deuterated, accompanied by its relatively thin dead layer, gives rise to unique applications in a wide range of UCN experiments, where it can be used to trap UCN and detect charged particles in situ. [ABSTRACT FROM AUTHOR]

A scintillator-based Timepix3 (TPX3) detector was developed to resolve the high-frequency modulation of a neutron beam in both spatial and temporal domains, as required for neutron spin-echo experiments. In this system, light from a scintillator is manipulated with an optical lens and is intensified using an image intensifier, making it detectable with the TPX3 chip. Two different scintillators, namely, 6LiF:ZnS(Ag) and 6LiI:Eu, were investigated to achieve the high resolution needed for spin-echo modulated small-angle neutron scattering (SEMSANS) and modulation of intensity with zero effort (MIEZE). The methodology for conducting event-mode analysis is described, including the optimization of clustering parameters for both scintillators. The detector with both scintillators was characterized with respect to detection efficiency, spatial resolution, count rate, uniformity, and γ-sensitivity. The 6LiF:ZnS(Ag) scintillator-based detector achieved a spatial resolution of 200 μm and a count rate capability of 1.1 × 105 cps, while the 6LiI:Eu scintillator-based detector demonstrated a spatial resolution of 250 μm and a count rate capability exceeding 2.9 × 105 cps. Furthermore, high-frequency intensity modulations in both spatial and temporal domains were successfully observed, confirming the suitability of this detector for SEMSANS and MIEZE techniques, respectively. [ABSTRACT FROM AUTHOR]

Benchtop pulsed x-ray systems are commonly used to record dynamic material data on the order of nanoseconds, but pulse timing is often difficult to accurately determine. This study demonstrates that commercially available photodiodes can be used effectively for direct x-ray pulse detection without the need for visible light scintillators. X-ray pulses from four commercially available flash x-ray systems were quantified using one silicon and two indium gallium arsenide (InGaAs) photodiodes. The measured InGaAs pulse durations were strongly dependent on radiation dose in the non-linear operating regime, so the photodiodes were shielded to operate below the 2.5 V non-linear regime threshold. The average pulse duration and pulse arrival time jitter of the photodiodes for each x-ray source were within several nanoseconds with the exception of two sets of measurements that were affected by low instrument sensitivity and electrical noise. These results show that InGaAs photodiodes can be used as effective and repeatable stand-alone timing diagnostics for x-ray pulses as short as 20 ns or less. [ABSTRACT FROM AUTHOR]

This work is devoted to the development of a method for the reconstruction of plasma extreme UV (EUV) spectra recorded by a three frame grazing incidence spectrograph (GIS-3D). The spectrograph provides registration of radiation reflected from the diffraction grating (DG) on a three-frame detector based on a microchannel plate with a scintillator screen and registration on a CCD camera, with an exposure time of one frame of ∼1.5 ns. DG has a gold-coated spherical concave form with a radius of curvature of 2 m and dimensions of 30 × 40 × 10 mm3. In this case, radiation is incident on the DG at a grazing angle of 2°; the DG period is 1.66 µm. The new single-pass method for the reconstruction of plasma EUV spectra was developed, which solves the inverse problem of decomposing experimental signals into separate contributions from each of the diffraction orders, followed by the reconstruction of the true plasma spectrum. Using the developed method, the possibility of finding a close approximation to the shape of a DG groove profile based on a priori information about the recorded spectra was demonstrated. In order to test and demonstrate the efficiency of this method, several experimental EUV spectra obtained at the Z-pinch facility Angara-5-1 with a current of ∼3–4 MA through loads made of either tungsten wires or polypropylene fibers were reconstructed. In addition, to test the single-pass method, the transmittance of EUV in cold aluminum was measured in the wavelength range of 3–35 nm, and it has a good match with the Henke database. [ABSTRACT FROM AUTHOR]

A relatively accurate, inexpensive, simple, and continuous quantification system for hydrogen and impurity gas(es) using a detector tube was developed in this study. Additionally, different detector tubes can be applied to measure different types of gases in a wide range from ppm order to % level. We optimized this system and evaluated its accuracy as well as the behavior of released H2 and impurity (NH3) gases from a hydrolysis of ammonia borane using a Pt/Al2O3 catalyst. The accuracy of hydrogen quantitation achieved by this system was comparable to that of commercial mass flow meters, and the accuracy of ammonia quantitation was 10% or 5% relative standard deviation, which depends on the detector tube. The concentration of released NH3 was evaluated by image analysis with a time-lapse video of the detector tube and succeeded in analyzing from ppm to % order. The H2 and NH3 release behaviors agreed with pH, and the percentage of reaction was estimated by NMR measurement of the reacted solution. These results confirmed the accuracy of this system. [ABSTRACT FROM AUTHOR]

Real-time measurement and characterization of laser-driven proton beams have become crucial with the advent of high-repetition-rate laser acceleration. Common passive diagnostics such as radiochromic film (RCF) are not suitable for real-time operation due to time-consuming post-processing; therefore, a novel approach is needed. Various scintillator-based detectors have recently gained interest as real-time substitutes to RCF—thanks to their fast response for a wide range of dose deposition rates. This work introduces a compact, scalable, and cost-effective scintillator-based device for proton beam measurements in real-time suitable for the laser–plasma environment. An advanced signal processing technique was implemented based on detailed Monte Carlo simulations, enabling an accurate unfolding of the proton energy and the depth–dose deposition curve. The quenching effect was accounted for based on Birks' law with the help of the Monte Carlo simulations. The detector was tested in a proof-of-principle experiment at a conventional cyclotron accelerating protons up to 35 MeV of energy. The signal comparison with a standard RCF stack was also performed during the test of the device, showing an excellent agreement between the two diagnostics. Such devices would be suitable for both conventional and laser-driven proton beam characterization. [ABSTRACT FROM AUTHOR]

We have developed a new scintillator-based optical soft x-ray (OSXR) diagnostic system for KSTAR. By utilizing fiber optic faceplates, mm-size lens arrays, and fiber bundles, we have successfully constructed a novel optical system for scintillator-based soft x-ray detection to overcome the limited vacuum-port conditions in KSTAR. P47 (Y2SiO5), which has a fast rise (∼7 ns) and decay (∼100 ns) time sufficient for detecting plasma instabilities observed in the kHz–MHz spectral range, was selected as the scintillator material for the KSTAR OSXR system. Scintillation toward each detection channel is collected by the lens arrays coupled to optical fiber cores, which are connected to the photodetector system. Initial results obtained during the 2022 KSTAR experimental campaign support the validity of the OSXR data through the consistency of OSXR measurement results with other diagnostics. We also observe that the OSXR system can capture magnetohydrodynamic activities, such as sawtooth oscillations, and provide valuable information for disruption mitigation studies using shattered pellet injection. [ABSTRACT FROM AUTHOR]

We report the preparation of the ZnO-6LiF composite with a polystyrene (PS) polymer as a host using the solution mixing process. 6LiF acts as a converter material that absorbs a thermal neutron and produces alpha particles, which excites ZnO micro-particles, resulting in UV–vis photons' emission. The free-standing ZnO-6LiF/PS composite film is coupled to a photomultiplier tube (PMT). 241Am-Be (1Ci) is used as the neutron radiation source for measuring the response. We compared the response of the composite scintillator consisting of (i) natural LiF and (ii) 95% 6Li enriched LiF (6LiF). The increased pulse heights are recorded for 95% 6Li enriched, i.e., 6LiF converter. It confirms the generation of alpha particles after the absorption of a neutron in 6LiF. Furthermore, ZnO and 6LiF are considered in different weight proportions, 2:1, 1:1, and 1:2, keeping the total loading 50% (w/w) of polystyrene. The ZnO:6LiF (1:1)/PS composite showed higher scintillation pulse heights than the other two composites. Repetitive measurements are performed for the ZnO-6LiF(1:1)/PS composite, showing ±5% variation in respective responses. We also investigated the impact of different counting times and source-to-detector responses for the ZnO-6LiF(1:1)/PS composite. The response increases linearly with neutron dose, exhibiting a sensitivity of ∼203 counts/μSv. Neutron measurement counts at different source-to-detector distances have a similar trend as that of neutron dose measured by using a neutron dosimeter. Thus, this work demonstrated the potential of the ZnO-6LiF/PS composite, coupled to PMT for detecting thermal neutron radiation. [ABSTRACT FROM AUTHOR]

We present the development of a compact Thomson parabola ion spectrometer capable of characterizing the energy spectra of various ion species of multi-MeV ion beams from > 1 0 20 W / cm 2 laser produced plasmas at rates commensurate with the highest available from any of the current and near-future PW-class laser facilities. This diagnostic makes use of a polyvinyl toluene based fast plastic scintillator (EJ-260), and the emitted light is collected using an optical imaging system coupled to a thermoelectrically cooled scientific complementary metal–oxide–semiconductor camera. This offers a robust solution for data acquisition at a high repetition rate, while avoiding the added complications and nonlinearities of micro-channel plate based systems. Different ion energy ranges can be probed using a modular magnet setup, a variable electric field, and a varying drift-distance. We have demonstrated operation and data collection with this system at up to 0.2 Hz from plasmas created by irradiating a solid target, limited only by the targeting system. With the appropriate software, on-the-fly ion spectral analysis will be possible, enabling real-time experimental control at multi-Hz repetition rates. [ABSTRACT FROM AUTHOR]

High-resolution photon-counting detector (PCD) computed tomography (CT) imaging is increasingly used for several applications. Recent technological advances in CT instrumentation have introduced various types of radiation detectors. Therefore, this work aims at evaluating the lutetium–yttrium oxyorthosilicate (LYSO) scintillator for use in PCD CT from a detector point of view. To do so, a mini-CT prototype was designed and constructed based on the pixelated LYSO blocks. The detector comprises four 10 × 10 linearly arranged LYSO blocks coupled with four position-sensitive photomultiplier tubes. The prototype utilizes a point gamma-ray source along with a cone-beam collimator. An in-home MATLAB-based data processing software package was also developed for storing the list-mode data, event positioning, and energy windowing. A set of experiments were conducted to assess the performance of the constructed energy-resolved LYSO:Ce detector for mini-CT imaging. The results show good crystal identification for all blocks with a maximum peak-to-valley ratio of 3.48. In addition, the findings confirm that the developed detector is position-sensitive. The 20% energy window provides an optimal performance by simultaneously providing good crystal identification and a scatter removal factor of 0.71. A 96% uniformity was also observed when the detector was irradiated with a uniform flood. The spatial resolution of the mini-CT prototype in the x- and y-directions was calculated to be 0.9 and 0.93 mm, respectively, corrected for a magnification factor of 2.5. It is concluded that the pixelated LYSO crystal is a promising alternative to the current detectors and would be the scintillator of choice for high-resolution PCD CT imaging tasks. [ABSTRACT FROM AUTHOR]

A PIN-diode-based 1D x-ray camera and a scintillator-based 1D x-ray camera, both with a microsecond to submicrosecond time resolution, have been developed to perform time-resolved imaging of transient, low-intensity, suprathermal x-rays associated with magnetohydrodynamic instabilities disrupting a plasma jet. These cameras have a high detection efficiency over a broad x-ray band, a wide field of view, and the capability to produce > 50 time-resolved frames with a ≤ 1 μs time resolution. The x-ray images are formed by a pinhole or by a coded aperture placed outside a vacuum chamber in which the plasma jet is launched. The 1D imaging shows that the location of the x-ray source is either a few centimeters away from an inner disk electrode or near a spatially translatable metal frame that is 30–40 cm away from the electrode. Compared to a pinhole, a coded aperture increases the signal collection efficiency but also introduces unwanted artifacts. [ABSTRACT FROM AUTHOR]

A new broad-energy, high-resolution gamma ray spectrometer (GRS) with Compton suppression function has been developed recently in the HL-2A tokamak to obtain the gamma ray information in the energy range of 0.1–10 MeV. This is the first time to develop an anti-Compton GRS for a magnetic confinement fusion device. The anticoincidence detector consists of a large-volume high purity germanium (HPGe) crystal (Φ63 × 63 mm2) as the primary detector and eight trapezoidal bismuth germinate (BGO) scintillators (trapezoid crystal with 30 mm thickness) as the secondary detector. The anti-coincidence data processing is implemented by a digital-based data acquisition system with fast digitization and software signal processing technology. Using radioisotope gamma ray sources and Monte Carlo N-Particle code, the energy and efficiency of the spectrometer have been calibrated and quantitatively tested. The Compton continuum suppression factor reaches 4.2, and the energy resolution (Full Width at Half Maximum) of the 1.332 MeV full energy peak for 60Co is 2.1 keV. Measurements of gamma ray spectra with Compton suppression using the spectrometer have been successfully performed during HL-2A discharges with different conditions. The performance of the spectrometer and the first experimental results are presented in this paper. [ABSTRACT FROM AUTHOR]

A fast neutron tomography imaging instrument has been designed, built, and tested at The Ohio State University 500 kW Research Reactor on a fast neutron beamline with a peak neutron flux ≈5.4 × 107 n·cm−2·s−1 at 1.6 MeV median neutron energy. The instrument and beamline are also configurable for thermal neutron imaging. The imaging apparatus is composed of a lens coupled, water-cooled Electron Multiplying Charge Coupled Device camera, a front-surface mirror, and a high light yield plastic Polyvinyl toluene scintillator. The instrument sits on a mobile cart. A total of 5 motion-control stages are built into the system for XYZ and rotational degrees of freedom for sample positioning; the fifth stage fine tunes the focal distance between the camera and the scintillator to achieve on-line focusing. A Python code with a user-friendly graphical user interface controls the fully automated image acquisition, not requiring user interaction, yet facilitating tracking of the image acquisition. A complete fast neutron computed tomography dataset with 360 projections requires less than 3 h, with 30 s per projection. On-line focusing is accomplished with a commercial, off-the-shelf, dielectrically actuated liquid lens. Finally, tomographic reconstructions are visualized using the Livermore Tomography Tools software package. The effective pixel size (width and height) is ≈0.1058 mm, yielding a minimum voxel size of 0.1058 × 0.1058 × 0.1058 mm3, and produces a spatial resolution of 231 μm when calculated from knife-edge measurements. [ABSTRACT FROM AUTHOR]

Dedicated nuclear diagnostics have been designed, developed, and built within EUROFUSION enhancement programs in the last ten years for installation at the Joint European Torus and capable of operation in high power Deuterium–Tritium (DT) plasmas. The recent DT Experiment campaign, called DTE2, has been successfully carried out in the second half of 2021 and provides a unique opportunity to evaluate the performance of the new nuclear diagnostics and for an understanding of their behavior in the record high 14 MeV neutron yields (up to 4.7 × 1018 n/s) and total number of neutrons (up to 2 × 1019 n) achieved on a tokamak. In this work, we will focus on the 14 MeV high resolution neutron spectrometers based on artificial diamonds which, for the first time, have extensively been used to measure 14 MeV DT neutron spectra with unprecedented energy resolution (Full Width at Half Maximum of ≈1% at 14 MeV). The work will describe their long-term stability and operation over the DTE2 campaign as well as their performance as neutron spectrometers in terms of achieved energy resolution and high rate capability. This important experience will be used to outline the concept of a spectroscopic neutron camera for the SPARC tokamak. The proposed neutron camera will be the first one to feature the dual capability to measure (i) the 2.5 and 14 MeV neutron emissivity profile via the conventional neutron detectors based on liquid or plastics scintillators and (ii) the 14 MeV neutron spectral emission via the use of high-resolution diamond-based spectrometers. The new opportunities opened by the spectroscopic neutron camera to measure plasma parameters will be discussed. [ABSTRACT FROM AUTHOR]

We present in this work the development of an ultra-compact, multi-channel x-ray spectrometer (UCXS). This diagnostic has been specially built and adapted to perform at high-repetition-rate (>1 Hz) for high-intensity, short-pulse laser plasma experiments. X-ray filters of varying materials and thicknesses are chosen to provide spectral resolution up to ΔE ≈ 1 keV over the x-ray energy range of 1–30 keV. These filters are distributed over a total of 25 channels, where each x-ray filter is coupled to a single scintillator. The UCXS is designed to detect and resolve a large variety of laser-driven x-ray sources such as low energy bremsstrahlung emission, fluorescence, and betatron radiation (up to 30 keV). Preliminary results from commissioning experiments at the ABL laser facility at Colorado State University are provided. [ABSTRACT FROM AUTHOR]

Standard plastic scintillating fiber cannot detect low-energy β-rays as the cladding prevents them from reaching the fiber core. We developed an outer-layer scintillating (OLS) fiber with a plastic scintillator on the outermost layer for low-energy β-ray detection. The concept of fiber construction is presented. The fundamental optical properties of the OLS fiber, such as the emission spectrum, attenuation length, and scintillation decay time, were evaluated. Here, Ni-63 with a maximum energy of 67.0 keV was used as a low-energy β-emitting nuclide. Simulation studies on the interaction between low-energy electrons emitted from Ni-63 and a single fiber were performed prior to actual measurements. The data showed that Ni-63 can be measured using silicon photomultiplier photosensors in a coincidence mode. The OLS fiber was effective for low-energy β-ray detection. [ABSTRACT FROM AUTHOR]

In this study, we propose a hybrid coded-aperture and Compton camera based on cerium-doped Gd3Al2Ga3O12 (GAGG:Ce) scintillator arrays coupled with Multi-Pixel Photon Counter (MPPC) arrays. The sensitive detector of the gamma camera consists of a single GAGG:Ce crystal coupled with a single-chip MPPC unit module. An impedance bridge circuit and a 64-channel data acquisition system were employed to record the code-aperture events and Compton coincidence events. After the calibration of position and energy, the total energy resolution for 662 keV gamma-rays from 137Cs was 6.6%. The hybrid camera had the characteristics of mechanical collimation and electronic collimation at the same time. In the code aperture mode, the reconstructed images were obtained by direct deconvolution and maximum likelihood expectation maximization (MLEM) methods. In the Compton imaging mode, the energy-dependent method was applied to order the sequence of Compton scatter events. The simple back-projection algorithm and list-mode MLEM algorithm were adopted for image reconstruction. Practical performances demonstrated that the angular resolutions in two modes were measured as 5.2° and 11.4°, respectively. In addition, the hybrid camera had a desirable imaging capability in a wide energy range (32 keV–2.6 MeV) and a wide field of view (∼210° in the horizontal direction). As for the sensitivity, the camera had a commercially available sensitivity level of localizing a 137Cs point source, producing ∼0.026 µSv/h in 5 min. Furthermore, the function of distinction for different radiation sources was preliminarily realized. [ABSTRACT FROM AUTHOR]

Accurately and rapidly diagnosing laser–plasma interactions is often difficult due to the time-intensive nature of the analysis and will only become more so with the rise of high repetition rate lasers and the desire to implement feedback on a commensurate timescale. Diagnostic analysis employing machine learning techniques can help address this problem while maintaining a high degree of accuracy. We report on the application of machine learning to the analysis of a scintillator-based electron spectrometer for experiments on high intensity, laser–plasma interactions at the Colorado State University Advanced Lasers and Extreme Photonics facility. Our approach utilizes a neural network trained on synthetic data and tested on experiments to extract the accelerated electron temperature. By leveraging transfer learning, we demonstrate an improvement in the neural network accuracy, decreasing the network error by 50%. [ABSTRACT FROM AUTHOR]

Scintillators are vital components for nuclear instrumentation and its applications, including plasma diagnostics and imaging. As yields in controlled fusion experiments increase, the radiation tolerance of scintillator candidates for use in instrumentation is of particular importance. High radiation exposure can damage scintillating materials and alter the optical properties. The effects of radiation damage in Ce-doped mixed garnet ceramics over the compositional range (Y,Gd,Lu)3(Al,Ga)5O12 are investigated using optical techniques. The samples were exposed to 200 keV protons to an accumulated fluence of 1016 protons per square centimeter, then characterized using diffuse reflectance spectroscopy (DRS). DRS with visible light can assess the radiation tolerance of opaque poly-crystalline samples, which can be easily sintered from powders and thus offer distinct advantages in characterization compared to single crystals. Qualitative trends in induced absorption are presented as a function of composition, and the ideal cerium dopant concentration for Y2LuAl5O12 is determined to be 0.60–0.75 mol. %. [ABSTRACT FROM AUTHOR]

A new neutron time-of-flight (nTOF) detector for deuterium–deuterium (DD)-fusion yield and ion-temperature measurements was designed, installed, and calibrated for the OMEGA Laser Facility. This detector provides an additional line of sight for DD neutron yield and ion-temperature measurements for yields exceeding 1 × 1010 with higher precision than existing detectors. The nTOF detector consists of a 90-mm-diam, 20-mm-thick BC-422 scintillator and a gated Photek photomultiplier tube (PMT240). The PMT collects scintillating light through the 20-mm side of the scintillator without the use of a light guide. There is no lead shielding from hard x rays in order to allow the x-ray instrument response function of the detector to be measured easily. Instead, hard x-ray signals generated in implosion experiments are gated out by the PMT. The design provides a place for glass neutral-density filters between the scintillator and the PMT to avoid PMT saturation at high yields. The nTOF detector is installed in the OMEGA Target Bay along the P8A sub-port line of sight at a distance of 5.3 m from the target chamber center. In addition to DD measurements, the same detector can be used to measure the neutron yield and ion temperature from deuterium–tritium (DT) implosion targets in the 5 × 1010 to 2 × 1012 yield range. The design details and the calibration results of this nTOF detector for both D2 and DT implosions on OMEGA will be presented. [ABSTRACT FROM AUTHOR]

A hard x-ray spectrometer based on a φ25 × 25 mm2 LaBr3 scintillator has been developed to measure the runaway electron bremsstrahlung. Simulation results by GEANT4 show that x rays with an energy of 15 MeV can be effectively detected. In order to tolerate a high count rate, a self-made fast shaping amplifier is used to process the detector output into a fast bipolar pulse. The tested energy resolution, which was 3.4% for Cs-137 662 keV gamma rays, shows that the shaping amplifier does not significantly degrade the energy resolution. The results of the HL-2A discharge show that the maximum count rate can reach 2 MHz, and the time resolution of the spectrometer can reach the millisecond level. [ABSTRACT FROM AUTHOR]

Particle counting analysis (PCA) with a multi-stage scintillation detector shows a new perspective on angularly resolved spectral characterization of GeV-scale, multi-species ion beams produced by high-power lasers. The diagnosis provides a mass-dependent ion energy spectrum based on time-of-flight and pulse-height analysis of single particle events detected through repetitive experiments. With a novel arrangement of multiple scintillators with different ions stopping powers, PCA offers potential advantages over commonly used diagnostic instruments (CR-39, radiochromic films, Thomson parabola, etc.) in terms of coverage solid angle, detection efficiency for GeV-ions, and real-time analysis during the experiment. The basic detector unit was tested using 230-MeV proton beam from a synchrotron facility, where we demonstrated its potential ability to discriminate major ion species accelerated in laser–plasma experiments (i.e., protons, deuterons, carbon, and oxygen ions) with excellent energy and mass resolution. The proposed diagnostic concept would be essential for a better understanding of laser-driven particle acceleration, which paves the way toward all-optical compact accelerators for a range of applications. [ABSTRACT FROM AUTHOR]

A new type of compact high-resolution high-sensitivity gamma-ray spectrometer for short-pulse intense gamma-rays (250 keV to 50 MeV) has been developed by combining the principles of scintillators and attenuation spectrometers. The first prototype of this scintillator attenuation spectrometer (SAS) was tested successfully in Trident laser experiments at LANL. Later versions have been used extensively in the Texas Petawatt laser experiments in Austin, TX, and more recently in OMEGA-EP laser experiments at LLE, Rochester, NY. The SAS is particularly useful for high-repetition-rate laser applications. Here, we give a concise description of the design principles, capabilities, and sample preliminary results of the SAS. [ABSTRACT FROM AUTHOR]

A high-speed radiation imaging system based on an image converter of liquid scintillator filled capillary arrays has been developed, which is sensitive to x rays, gamma rays, and neutrons. This imaging system has advantages of both high spatial resolution and high sensitivity because increasing the thickness of the image converter only leads to little deterioration on imaging resolution. The capillary arrays have dimensions of 150 mm diameter and 50 mm thickness, with 100 µm diameter of each capillary. The fluorescence decay time of the filled liquid scintillator based on the mixture of p-xylene and 2,5-diphenyloxazole has been evaluated to be ∼3 ns with the single photon method under the gamma ray excitation. The spatial resolution has been experimentally evaluated to be about 1.15 and 0.6 mm, under excitation of x rays and neutrons, respectively. The imaging system has been applied for diagnosing the dynamic x-ray spot generated by the rod pinch. Two frames in single shot with 15 ns temporal resolution and 20 ns inter-frame separation time have been obtained, which show the spatiotemporal distribution of the electrons bombarding the tungsten rod, indicating the ability of this imaging system in diagnosing dynamic radiation objects. In addition, the technique of capillary arrays provides a promising path for applications of advanced liquid scintillators in the field of radiation imaging. [ABSTRACT FROM AUTHOR]

Due to the shortage of the 3He gas and its rapidly increasing price, scintillator detectors, the advantages of which are high spatial resolution and capability of detection in real time, become widely used in many neutron instruments. In this work, a position-sensitive neutron detector consisting of a 6LiF/ZnS scintillation screen and a silicon photomultiplier array linked to a capacitive network to detect the positions of incident neutrons, is constructed and tested. To evaluate the detector performance, a series of neutron beam experiments with the detector prototype were performed in the BL20 at the China Spallation Neutron Source. The spatial resolution was measured, and the energy-selective neutron imaging and Bragg edge measurements of a 316L stainless steel sample were performed. A sub-millimeter spatial resolution could be obtained for the detector prototype under study. The detector with such a high spatial resolution is promising for applications in neutron scattering experimental installations, especially for neutron single-crystal diffractometers. [ABSTRACT FROM AUTHOR]

Beamline 11.3.1 at the Advanced Light Source is a tender/hard (6–17 keV) x-ray bend magnet beamline recently re-purposed with a new full-field, nanoscale transmission x-ray microscope. The microscope is designed to image composite and porous materials possessing a submicrometer structure and compositional heterogeneity that determine materials' performance and geologic behavior. The theoretical and achieved resolutions are 55 and <100 nm, respectively. The microscope is used in tandem with a <25 nm eccentricity rotation stage for high-resolution volume imaging using nanoscale computed tomography. The system also features a novel bipolar illumination condenser for the illumination of an ∼100 μm spot of interest on the sample, followed by a phase-type zone plate magnifying objective of ∼52 µm field of view and a phase detection ring. The zone plate serves as the system objective and magnifies the sample with projection onto an indirect x-ray detection system, consisting of a polished single crystal CsI(Tl) scintillator and a range of high-quality Plan Fluorite visible light objectives. The objectives project the final visible light image onto a water-cooled CMOS 2048 × 2048-pixel2 detector. Here, we will discuss the salient features of this instrument and describe early results from imaging the internal three-dimensional microstructure and nanostructure of target materials, including fiber-reinforced composites and geomaterials. [ABSTRACT FROM AUTHOR]

Neutron imaging is a powerful tool for observing the internal structure of an object without destroying the object. Neutron imaging (neutron radiography) is a prominent application of neutrons but still requires significant improvements, for example, in sensitivity, resolution, radiation hardness, and handling of neutron imaging detectors. This paper presents the development and the first neutron imaging results of a neutron flat-panel detector (nFPD) based on an In–Ga–Zn–O (IGZO) thin-film transistor (TFT)/photodiode array coupled with a LiF/ZnS scintillator sheet. Direct photo-coupling to the scintillator increases the light collection efficiency. Moreover, unlike lens-coupled neutron cameras, the proposed detector is compact and easy to handle. Owing to the high off-state resistance of IGZO TFTs, their leakage current is lower than that of conventional TFTs, enabling the IGZO TFTs to hold an accumulated charge for a longer period of time and allowing longer exposure times for imaging. This would be a powerful feature for imaging at compact neutron sources with limited flux. This paper reports on the first neutron imaging results with an IGZO nFPD, its performance evaluation, and a demonstration of three-dimensional computed tomography with neutrons. [ABSTRACT FROM AUTHOR]

The advent of multi-PW laser facilities world-wide opens new opportunities for nuclear physics. With this perspective, we developed a neutron counter taking into account the specifics of a high-intensity laser environment. Using GEANT4 simulations and prototype testings, we report on the design of a modular neutron counter based on boron-10 enriched scintillators and a high-density polyethylene moderator. This detector has been calibrated using a plutonium–beryllium neutron source and commissioned during an actual neutron-producing laser experiment at the LULI2000 facility (France). An overall efficiency of 4.37(59)% has been demonstrated during calibration with a recovery time of a few hundred microseconds after laser–plasma interaction. [ABSTRACT FROM AUTHOR]

We present a table-top extreme ultraviolet (XUV) beamline for measuring time- and frequency-resolved XUV-excited optical luminescence (XEOL) with additional femtosecond-resolution XUV transient absorption spectroscopy functionality. XUV pulses are generated via high-harmonic generation using a near-infrared pulse in a noble gas medium and focused to excite luminescence from a solid sample. The luminescence is collimated and guided into a streak camera where its spectral components are temporally resolved with picosecond temporal resolution. We time-resolve XUV-excited luminescence and compare the results to luminescence decays excited at longer wavelengths for three different materials: (i) sodium salicylate, an often used XUV scintillator; (ii) fluorescent labeling molecule 4-carbazole benzoic (CB) acid; and (iii) a zirconium metal oxo-cluster labeled with CB, which is a photoresist candidate for extreme-ultraviolet lithography. Our results establish time-resolved XEOL as a new technique to measure transient XUV-driven phenomena in solid-state samples and identify decay mechanisms of molecules following XUV and soft-x-ray excitation. [ABSTRACT FROM AUTHOR]

Neutron–gamma discrimination (NGD) for gadolinium-containing scintillators is a challenging issue which prevents them from being used in highly efficient neutron detectors with high signal-to-noise ratios. Pulse-shape based digital-signal processing has been selected to tackle this issue, with an emphasis on the dimensionality reduction of the raw data and capability to mitigate the influence of noise, unwanted variations, and outliers on the accuracy of classification. We present two graph-embedded non-negative matrix factorization digital classifiers in which an event graph (or a network) is introduced to find a low-dimensional structure hidden in the high-dimensional experimental data. Utilizing energy-independent normalized features of waveforms and a graph composed of mixed-source reference events, the smooth or sparse low-dimensional representation of detector signals from a Ce:Gd3Al2Ga3O12 scintillator leads to a high thermal neutron detection efficiency (77%–80%) and a high NGD ratio (neutron–gamma efficiency ratio, ∼109) simultaneously. Moreover, excellent discrimination between neutron and ambient background events has been achieved. The proposed graph-embedded algorithms may be applied not only for thermal-neutron position-sensitive detectors and single-channel detectors but also for other radiation detectors that need excellent particle (or crystal) discrimination capabilities and high detection efficiencies in many applications, including medical imaging, nondestructive testing, and security scans. [ABSTRACT FROM AUTHOR]

We describe a scanning tunneling microscope (STM) that operates at magnetic fields up to 22 T and temperatures down to 80 mK. We discuss the design of the STM head, with an improved coarse approach, the vibration isolation system, and efforts to improve the energy resolution using compact filters for multiple lines. We measure the superconducting gap and Josephson effect in aluminum and show that we can resolve features in the density of states as small as 8 μeV. We measure the quantization of conductance in atomic size contacts and make atomic resolution and density of states images in the layered material 2H–NbSe2. The latter experiments are performed by continuously operating the STM at magnetic fields of 20 T in periods of several days without interruption. [ABSTRACT FROM AUTHOR]

Laser-based particle accelerators have been an active field of research for over two decades moving from laser systems capable of one shot every hour to systems able to deliver repetition rates in the Hz regime. Based on the advancements in laser technology, the corresponding detection methods need to develop from single to multiple use with high readout speed. Here, we present an online compact tracker of particles using scintillators with nine resolvable energy levels and a spatial resolution of 3.6 × 3.6 mm2 over the whole active area. This paper describes the design and construction of the detector, which is based on pixellated scintillators embedded inside an absorber matrix. The scintillator pixels are fiberoptically coupled to a camera system for online readout and analysis. Calibration with a radioactive source and first experimental data measuring laser accelerated ions at the PHELIX laser at GSI, Darmstadt, Germany, are presented and discussed. [ABSTRACT FROM AUTHOR]

When using liquid scintillator detectors to measure the neutron emission spectrum from fusion plasmas, the problem of pile-up distortion can be significant. Because of the large neutron rates encountered in many fusion experiments, some pile-up distortion can remain even after applying traditional pile-up elimination methods, which alters the shape of the measured light-yield spectrum and influences the spectroscopic analysis. Particularly, pile-up events appear as a high-energy tail in the measured light-yield spectrum, which obfuscates the contribution that supra-thermal ions make to the energy spectrum. It is important to understand the behavior of such "fast ions" in fusion plasmas, and it is hence desirable to be able to measure their contribution to the neutron spectrum as accurately as possible. This paper presents a technique for incorporating distortion from undetected pile-up events into the analysis of the light-yield spectrum, hence compensating for pile-up distortion. The spectral contribution from undetected pile-up events is determined using Monte Carlo methods and is included in the spectroscopic study as a pile-up component. The method is applied to data from an NE213 scintillator detector at JET and validated by comparing with results from the time-of-flight spectrometer TOFOR, which is not susceptible to pile-up distortion. Based on the results, we conclude that the suggested analysis method helps counteract the problem of pile-up effects and improves the possibilities for extracting accurate fast-ion information from the light-yield spectrum. [ABSTRACT FROM AUTHOR]

LAILA is a miniaturized eight-channel electronic readout system for compact γ-ray detectors, combining high-resolution spectroscopy capability with position sensitivity. Compactness is achieved by the combination of a novel CMOS front-end ASIC (Application-Specific Integrated Circuit) for analog processing of a large signal current from Silicon PhotoMultiplier (SiPM) solid-state photodetectors, with a microcontroller-based data acquisition system. The adoption of automatic gain regulation in the gated-integrator stage of the ASIC offers an 84 dB dynamic range, combining single-photon sensitivity with an extended input photon energy range (20 keV–4 MeV, using 30 μm-cell SiPMs). Using this module with properly merged 144 SiPM pixels coupled to a 3 in.-thick lanthanum bromide scintillation crystal, a 3% energy resolution at 662 keV and 1 cm spatial resolution in the estimation of the interaction coordinates are experimentally demonstrated in this work. [ABSTRACT FROM AUTHOR]

As an ultrafast inorganic scintillator, Yb-doped Y3Al5O12 [yttrium aluminum garnet (YAG)] crystals have potential applications in various fields, such as ultrafast radiation detection, solar neutrino detection, pulsed radiation imaging, and nuclear reaction kinetics diagnosis. In this work, the fluence rate effect of pulsed γ rays on the Yb:YAG scintillation crystal was investigated at the "QiangGuang-I" facility. The experiment results show that the fluence rate linear response upper limit of the Yb:YAG crystal is about 9.1 × 1018 MeV cm−2 s−1. The Yb:YAG crystal changed from colorless to yellow, and the relative light output decreased to 63% of its initial value after the irradiations, which were attributed to the radiation induced damage. It is deduced that oxygen vacancies and divalent Yb cations were generated after the irradiations. [ABSTRACT FROM AUTHOR]

The continuing improvement in quantum efficiency (above 90% for single visible photons), reduction in noise (below 1 electron per pixel), and shrink in pixel pitch (less than 1 μm) enable billion-pixel x-ray cameras (BiPC-X) based on commercial complementary metal–oxide–semiconductor (CMOS) imaging sensors. We describe BiPC-X designs and prototype construction based on flexible tiling of commercial CMOS imaging sensors with millions of pixels. Device models are given for direct detection of low energy x rays (<10 keV) and indirect detection of higher energies using scintillators. Modified Birks's law is proposed for light yield non-proportionality in scintillators as a function of x-ray energy. Single x-ray sensitivity and spatial resolution have been validated experimentally using a laboratory x-ray source and the Argonne Advanced Photon Source. Possible applications include wide field-of-view or large x-ray aperture measurements in high-temperature plasmas, the state-of-the-art synchrotron, x-ray free electron laser, and pulsed power facilities. [ABSTRACT FROM AUTHOR]

A synthetic fast-ion loss (FIL) detector and an imaging Heavy Ion Beam Probe (i-HIBP) have been implemented in the 3D hybrid kinetic-magnetohydrodynamic code MEGA. First synthetic measurements from these two diagnostics have been obtained for neutral beam injection-driven Alfvén Eigenmode (AE) simulated with MEGA. The synthetic FILs show a strong correlation with the AE amplitude. This correlation is observed in the phase-space, represented in coordinates (Pϕ, E), being toroidal canonical momentum and energy, respectively. FILs and the energy exchange diagrams of the confined population are connected with lines of constant E′, a linear combination of E and Pϕ. First i-HIBP synthetic signals also have been computed for the simulated AE, showing displacements in the strike line of the order of ∼1 mm, above the expected resolution in the i-HIBP scintillator of ∼100 μm. [ABSTRACT FROM AUTHOR]

A 16-channel fiber optically coupled radiation detection array has been developed for studies of radiation asymmetries and emission histories from the Verus Research 750-kJ Dense Plasma Focus. Each detector in the array consists of a light-tight housing with a plastic scintillator coupled to a fiber optic that is fed into one channel of a multi-anode photomultiplier tube (PMT). The PMT and associated electronics are located in a remote electrically shielded control room. The detector head is configurable for using a Be-9 foil to take advantage of the 9Be(n,α)6He reaction as a fast neutron activation detector or with a bare scintillator alone to record the radiation emission history. Fiber optically coupling the detector head not only provides electrical isolation in the pulsed power environment but also allows the spatial footprint of the detector array to be reduced with concomitant flexibility in positioning each individual detector head. The array allows for spatially resolved neutron yield and radiation waveform measurements for fast z-pinches. The activation detector heads were calibrated for the total neutron yield against silver and indium activation counters for the total neutron yield. Fiber scintillation was found to contribute to the time-resolved detector head signals and was accounted for. [ABSTRACT FROM AUTHOR]

An Imaging Neutral Particle Analyzer (INPA) diagnostic has been designed for the ASDEX Upgrade (AUG) tokamak. The AUG INPA diagnostic will measure fast neutrals escaping the plasma after charge exchange reactions. The neutrals will be ionized by a 20 nm carbon foil and deflected toward a scintillator by the local magnetic field. The use of a neutral beam injector (NBI) as an active source of neutrals will provide radially resolved measurements, while the use of a scintillator as an active component will allow us to cover the whole plasma along the NBI line with unprecedented phase-space resolution (<12 keV and 8 cm) and a fast temporal response (up to 1 kHz with the high resolution acquisition system and above 100 kHz with the low resolution one), making it suitable to study localized fast-ion redistributions in phase space. [ABSTRACT FROM AUTHOR]

The JET FILD is a scintillator-based Fast-ion Loss Detector optimized to measure fusion-born alpha-particle losses. This work covers its upgrade and absolute calibration in preparation for the following JET DT experiments. A fast scintillator material (TG-Green) has been installed in the JET FILD. A heater jacket is installed around the fiber bundle, responsible for transmitting the light from the scintillator plate, to anneal the fiber obscuring due to neutron damage. The JET FILD has been upgraded with a 1 Mpx camera and 2 MHz photomultiplier data acquisition hardware. Full-orbit simulations give an estimate of the shading effects on the scintillator plate of the first wall structures and provide a synthetic signal of the JET FILD. A detector instrument function enables absolute values of fast-ion losses using calibration factors. The calibration factors are made available in a shot-to-shot basis for the characterized species and energies and with corrections for the diagnostic conditions. The fast acquisition system sets the Nyquist frequency (1 MHz) above the typical mode frequencies (≈102 kHz), thus making it possible to identify MHD-induced fast-ion losses. [ABSTRACT FROM AUTHOR]

This work studies in detail the application possibility of a chlorine-based cerium-doped scintillator crystal [LaCl3(Ce)] to the task of D–D neutron spectrometry. We conducted an experimental campaign aimed at deriving the optimal setup parameters and energy calibration using a variety of available neutrons and γ-sources. The GEANT4 code was used for modeling the detector response to γ-ray irradiation. By observing the intrinsic background α-activity of the crystal, we were able to fine-tune the pulse-shape discrimination parameters, achieving a satisfactory α/n/γ pulse selection. We also investigated the LaCl3(Ce)-based spectrometer response under D–D-neutron irradiation by means of the ING-07D neutron generator with the yield of 1 × 107 n/s. The GEANT4 simulation provided us with the comprehensive overview of detector performance. The acquired results demonstrate the possibility of using the LaCl3(Ce) scintillation spectrometer for the purposes of deuterium plasma neutron diagnostics. [ABSTRACT FROM AUTHOR]

Stilbene crystal detectors are widely used as fast neutron measurement tools based on recoil proton detection, such as liquid scintillators. A compact stilbene crystal neutron spectrometer (CSCNS) has been installed at the Experimental Advanced Superconducting Tokamak (EAST) to obtain information on fuel ions produced in the plasma core because of its merits of good n/γ discrimination capability, high detection efficiency, and fast response. For the first time, CSCNS has been used for neutron emission spectroscopy measurements in EAST plasmas with neutral beam injection (NBI) heating. The CSCNS has the same horizontal line of sight as the time-of-flight enhanced diagnostics neutron spectrometer. Under NBI heating scenarios, the time trace of the neutron yield monitored by the CSCNS is similar to the one monitored by a standard 235U fission chamber. The experimental pulse height spectra are also similar to the simulated ones generated by folding the simulated neutron energy spectrum with the detector response functions. These results demonstrate the capability of the CSCNS for neutron diagnostics and the study of fast-ion physics in EAST. [ABSTRACT FROM AUTHOR]

Dynamic Light Scattering (DLS) and Small-Angle Neutron Scattering (SANS) are two key tools to probe the dynamic and static structure factors, respectively, in soft matter. Usually, DLS and SANS measurements are performed separately, in different laboratories, on different samples, and at different times. However, this methodology has particular disadvantages for a large variety of soft materials, which exhibit a high sensitivity to small changes in fundamental parameters, such as waiting times, concentration, pH, and ionic strength. Here, we report on a new portable DLS-SANS apparatus that allows one to simultaneously measure both the microscopic dynamics (through DLS) and the static structure (through SANS) on the same sample. The apparatus has been constructed as a collaboration between two laboratories, each an expert in one of the scattering methods, and was commissioned on the LOQ and ZOOM SANS instruments at the ISIS Pulsed Neutron and Muon Source, U.K. [ABSTRACT FROM AUTHOR]

Measurement of the neutron spectrum from inertial confinement fusion implosions is one of the primary diagnostics of implosion performance. Analysis of the spectrum gives access to quantities such as neutron yield, hot-spot velocity, apparent ion temperature, and compressed fuel ρr through measurement of the down-scatter ratio. On the National Ignition Facility, the neutron time-of-flight suite has been upgraded to include five independent, collimated lines of sight, each comprising a high dynamic range bibenzyl/diphenylacetylene-stilbene scintillator [R. Hatarik et al., Plasma Fusion Res. 9, 4404104 (2014)] and high-speed fused silica Cherenkov detectors [A. S. Moore et al., Rev. Sci. Instrum. 89, 10I120 (2018)]. [ABSTRACT FROM AUTHOR]

In this paper, we report studies of the Fermi potential and loss per bounce of ultracold neutrons (UCNs) on a deuterated scintillator (Eljen-299-02D). These UCN properties of the scintillator enable its use in a wide variety of applications in fundamental neutron research. [ABSTRACT FROM AUTHOR]

This paper proposes a new base material, a mixture of alcohol and water, for liquid scintillators. To date, there are no previous R&D studies for particle detectors with alcohol. In this study, 2-ethoxyethanol, which has a higher density than ethanol, was used to make an equivalent substance to the human body, namely, the skin or epidermis. This paper describes the brief synthesizing process of the alcohol-based liquid scintillator that was investigated and presents some of the feasible results. As one of its applications, a range (beam-path-length) measurement using an electron beam in medical physics is also described. Then, Monte Carlo simulation was performed for comparison with several other measurement results in medical physics. One of the intriguing results is that liquid scintillator component analysis can be performed through the pixel information stored in a mobile digital camera. Through the emission spectra of light, the component of the wavelength converting substances dissolved in the liquid scintillator can be known in the visible region without opening the sealed liquid scintillator. In the near future, the new alcohol-based liquid scintillator currently developed could be used for particle detector or medical imaging applications. [ABSTRACT FROM AUTHOR]

A traditional neutron time-of-flight (nTOF) detector used in inertial confinement fusion consists of a scintillator coupled with a photomultiplier tube (PMT). The instrument response function (IRF) of such a detector is dominated by the scintillator-light decay. In DT implosions with neutron yield larger than 1013, a novel detector consisting of a microchannel-plate (MCP) photomultiplier tube in a housing without a scintillator (PMT nTOF) can be used to measure DT yield, ion temperature, and neutron velocity. Most of the neutron signals in PMT nTOF detectors are produced from neutron interaction with a PMT window. The direct interaction of neutrons with the MCP provides negligible contribution. The elimination of the scintillator removes the scintillator decay from the instrument response function and makes the IRF of the PMT nTOF detector faster, which makes the ion temperature and neutron velocity measurements more accurate. Three PMT nTOF detectors were deployed in the OMEGA laser system for the first time to diagnose inertial confinement fusion plasma. The design details, characteristics, and calibration results of these detectors in DT implosions on OMEGA are presented. Recommendations on the use of different PMTs for specific applications are provided. [ABSTRACT FROM AUTHOR]

The spatial resolution and imaging characteristics of plastic scintillators are characterized using laser-driven proton beams. Laser-driven proton beams typically have broad energy spectra and are accompanied by relativistic electrons and high-energy photons, both potentially contributing to background noise. Different types and thicknesses of Eljen Technology scintillators are compared to determine their intrinsic point spread function. Point-projection imaging of a mesh is used to compare the imaging resolution of the scintillator to the usual imaging detector, radiochromic film, and is found to be reasonably comparable and sufficient for many experimental applications. [ABSTRACT FROM AUTHOR]

A pixelated scintillator has been designed, fabricated, and tested using a laser-accelerated proton source for use in proton diagnostics at rep-rated laser facilities. The work presented here demonstrates the enhanced spatial resolution of thin, organic scintillators through a novel pixelation technique. Experimental measurements using laser-generated protons incident onto 130 μm-thick scintillators indicate a >20% reduction in the scintillator point spread function (PSF) for the detectors tested. The best performing pixelated detector reduced the ∼200 μm PSF of the stock material to ∼150 μm. The fabrication technique may be tailored to reduce the pixel size and achieve higher spatial resolutions. [ABSTRACT FROM AUTHOR]

This article reports on a cryogenic setup that can be used for multifunctional experimental purposes. The temperature of the setup can be set from 10 K to 300 K. Different kinds of experiments were carried out in this experimental setup such as (1) luminescence emission, light yield, and decay time measurement under excitation of 266 nm laser and 280 nm LED sources, (2) thermoluminescence (TL) measurement under an x-ray excitation source, (3) scintillation property measurements such as light output, energy resolution, and decay time under 137Cs (662 keV γ-rays) and 241Am (5.4 MeV α) isotope sources, and (4) scintillation measurement under a 90Sr beta source through the continuous single-photon counting technique. The luminescence and scintillation properties of various molybdate and tungstate crystals such as CaMoO4, Na2Mo2O7, Pb2MoO5, CdWO4, and ZnWO4 are characterized and reported in the present work. The TL measurement of a CaMoO4 crystal is carried out from 10 K to 300 K, and various kinetic parameters such as order of kinetics, frequency factor, activation energy, and figure of merit are calculated for different TL peaks. As the temperature goes down from room to 10 K, the light yield of all studied crystals increases. Since the light yield of the crystal increases as temperature decreases toward 10 K, this experimental setup can be used for the characterization of luminescence and scintillation properties of a single crystal for rare event searches such as neutrinoless double-beta decay and dark matter. [ABSTRACT FROM AUTHOR]