Search

In this paper, the method for synthesis of a quasi-optical transmission line (QOTL) for a 45-GHz/20-kW Electron Cyclotron Resonance (ECR) ion source is proposed. The QOTL consists of five quasi-optical elliptical mirrors which had successfully transmitted the microwave power of about 12.8 m from the output of the matching optical unit to the vacuum window of the corrugated waveguide. The lengths of the major and minor axes of the five elliptical mirrors are optimized by adopting the Nelder–Mead simplex algorithm to achieve the maximum power transmission efficiency. Meanwhile, analysis of the electromagnetic fields in the QOTL system has been developed in terms of the vector diffraction theory. The model of the QOTL system is built using the Altair Feko software to simulate the electromagnetic wave propagating in free space. After the optimized design and simulation verification, the QOTL system has been fabricated, installed, and measured. The experimental results reveal that the power transmission efficiency of the QOTL system is 86.5%, including diffractive and ohmic losses. Moreover, the correlation coefficient reaches 96.53% between the field pattern of the theoretical value and the measured value at the vacuum window of the 45-GHz/20-kW ECR ion source. [ABSTRACT FROM AUTHOR]

The Space Plasma Environment Research Facility (SPERF) was built in Harbin to study the three-dimensional magnetic reconnection and wave–particle interactions relevant to space physics in laboratory settings. A 2.45 GHz Electron Cyclotron Resonance (ECR) plasma source is adopted in the device to simulate the Earth's magnetosphere and achieve the scientific goals. In this paper, the design of the ECR plasma source is presented. The structures of the microwave source, the microwave transfer system, and the antenna are introduced. Additionally, the resonant surfaces are computed to predict the locations of microwave absorption. The absorption mechanisms of the microwave in the SPERF are also discussed. The discharge experiment demonstrates the utility of the ECR source in simulating the Earth's magnetosphere. The successful operation of the source indicates that the ECR discharge is a powerful tool for creating a plasma environment in a large plasma experimental device. [ABSTRACT FROM AUTHOR]

The Rare-isotope Accelerator complex for ON-line experiments is a heavy-ion accelerator facility that accelerates a stable or rare isotope beam up to 400 kW with an energy of 200 MeV/u. Various heavy-ion beams are generated from the Electron Cyclotron Resonance Ion Source, with an energy of 10 keV/u and separated according to A/Q at the first dipole magnet (DM). To measure beam transverse emittance at the Low Energy Beam Transport section, two Allison scanners are installed behind the DM for the X and Y directions. It consist of a servo motor for driving, a Faraday cup for current measurement, deflection plates, and electronic device. The measurable range of beam angle in of the Allison scanner is determined by the structure of the deflection plate and designed based on mathematical calculations. Experimental Physics and Industrial Control System (EPICS) is adopted to integrate and control a variety of devices. To control the complex measurement sequence of the Allison scanner, an EPICS sequencer module was used. Normalized emittance is calculated by python code with Pyepics module using phase space distribution data. In this paper, we present the detailed design of the Allison scanner, the configuration of the control system, and the experimental results using an Ar9+ 30 μA beam. [ABSTRACT FROM AUTHOR]

The Advanced Ion Source for Hadrontherapy (AISHa) is an electron cyclotron resonance ion source operating at 18 GHz, developed at the Istituto Nazionale di Fisica Nucleare-Laboratori Nazionali del Sud, with the aim of producing high intensity and low emittance highly charged ion beams for hadrontherapy purposes. Moreover, thanks to its unique peculiarities, AISHa is a suitable choice for industrial and scientific applications. In the framework of the INSpIRIT and IRPT projects, in collaboration with the Centro Nazionale di Adroterapia Oncologica, new candidates for cancer treatment are being developed. In particular, the paper presents the results of the commissioning of four ion beams of interest for hadrontherapy: H+, C4+, He2+, and O6+. Their charge state distribution in the best experimental conditions, their emittance, and brightness will be critically discussed, along with the role of ion source tuning and space charge effects in beam transport. Perspectives for further developments will also be presented. [ABSTRACT FROM AUTHOR]

In this paper, a 28 GHz TE01 mode 160° miter bend employing two plane mirrors is proposed based on the quasi-optical technique and the coupled wave theory to realize high-efficiency transmission for the electron cyclotron resonance ion source. First, the TE01 mode was converted to TE0n hybrid modes with Gaussian beam characteristics by means of the designed mode converter. Second, the phase shift section was implemented to eliminate the phase difference of the hybrid modes. Then, upon reflection of two plane mirrors, the propagation direction of a wave beam is deviated by 160°. Finally, the hybrid modes were converted to the TE01 mode using the same structures of the phase shift section and the mode converter. The simulation results reveal that the TE01 mode transmission efficiency reaches 95.22% at the central frequency of 28 GHz. Additionally, the designed 160° miter bend has been fabricated, installed, and measured. The experimental results show that the power transmission efficiency reaches 98.54% including diffraction losses and ohmic losses. [ABSTRACT FROM AUTHOR]

Forward modeling is used to interpret inversion patterns of the pedestal–Scrape of Layer (SOL) Electron Cyclotron Emission (ECE) in DIII-D H-mode experiments. The modeling not only significantly improves the ECE data interpretation quality but also leads to the potential measurements of (1) the magnetic field strength |B| at the separatrix, (2) the pedestal |B| evolution during an inter-Edge Localized Mode (ELM) period, and (3) the pedestal Magnetohydrodynamics (MHD) radial structure. The ECE shine-through effect leads to three types of pedestal–SOL radiation inversions that are discussed in this paper. The first type of inversion is the non-monotonic Te,rad profile with respect to the major radius. Using the ECE frequency at the minimum Te,rad, the inversion can be applied to measure the magnetic field |B| at the separatrix and calibrate the mapping of the ECE channels with respect to the separatrix. The second type of inversion refers to the opposite phase between the radiation fluctuations δTe,rad at the pedestal and SOL. This δTe,rad phase inversion is sensitive to density and temperature fluctuations at the pedestal foot and, thus, can be used to qualitatively measure the MHD radial structure. The third type of inversion appears when the pedestal and SOL Te,rad evolve in an opposite trend, which can be used to infer the pedestal |B| field change during an inter-ELM period. The bandwidth effect on measuring δTe,rad due to pedestal MHD is also investigated in the radiation modeling. [ABSTRACT FROM AUTHOR]

An isotope enrichment system for 39Ar has been developed at the Institute of Modern Physics, which is designed to increase the abundance of 39Ar in the incident sample gas. With intense Ar+ beams produced by a 2.45 GHz electron cyclotron resonance ion source and a high mass resolution spectrometer system, Ar isotopes are evidently separated on the target plane and selectively collected by an Al target. The separated Ar isotopes have been identified on the target plane, which is consistent with the simulations. According to the recent cross-checked results with atom trap trace analysis, a high enrichment factor of 39Ar has been successfully achieved. This paper will present the design and test results of this system. [ABSTRACT FROM AUTHOR]

To ensure further progress in the development of electron cyclotron resonance ion sources (ECRISs), deeper understanding of the underlying physics is required. The electron energy distribution (EED), which is crucial for the performance of an ECRIS, still remains obscure. The present paper focuses on the details of a well-developed technique of measuring the EED of electrons escaping axially from the magnetically confined plasma of an ECRIS. The method allows for better than 500 eV energy resolution over a range of electron energies from 4 keV to over 1 MeV. We present detailed explanation of the experimental procedure and the following data processing peculiarities with examples and discuss possible reasons of energetic electron losses from the magnetic trap, in particular the role of RF pitch angle scattering. Finally, an experimental method of approximating the confined EED based on the measurement of escaping electrons is described. [ABSTRACT FROM AUTHOR]

The performance of a minimum-B Electron Cyclotron Resonance Ion Source (ECRIS) is traditionally quantified by measuring the beam current and quality of the extracted ion beams of different charge state ions. The stability of the extracted ion beam currents has drawn more attention recently as the technology is pushing its limits toward higher ion charge states and beam intensities. The stability of the extracted beam is often compromised by plasma instabilities manifesting themselves as rapid oscillations of the beam currents in millisecond scale. This paper focuses on practical aspects of diagnostics techniques of the instabilities, showcases examples of instability-related diagnostics signals, and links them to the plasma physics of ECR ion sources. The reviewed techniques include time-resolved microwave emission diagnostics, bremsstrahlung measurements, direct measurement of electron and ion fluxes, measurement of the ion beam energy spread, and optical emission diagnostics. We list the advantages and disadvantages of each technique and outline the development needs of further diagnostics. Finally, we discuss the implications of the instabilities in both historical and forward-looking context of ECRIS development. [ABSTRACT FROM AUTHOR]

We insert two probes in the upstream and the downstream regions with respect to the electron cyclotron resonance (ECR) zone which is formed at the center of mirror fields. We measure simultaneously plasma parameters in those regions by each of them under the same operating condition. We measure ion saturation currents Iis and electron energy distribution functions at two positions. We obtain measurement results that suggest the more efficient ECR on the side closer to the microwave-launchings than those on the other side. It is consistent with the accessibility condition of the right-hand polarization wave. We also compare the charge state distributions of Ar ion beams extracted in the case of launching microwaves from the coaxial semi-dipole antenna and those from the rod antenna. We observe the higher multicharged ion beam currents at the low microwave powers in the case of the rod antenna than those in the case of the coaxial semi-dipole antenna. We also confirm stable increasements of ion beam currents at considerably high microwave powers in the case of the coaxial semi-dipole antenna. Based on the experimental results, we propose a new microwave-launching method, "dual-ECR heating" and report its preferable preliminary experimental results in this paper. [ABSTRACT FROM AUTHOR]

Production of high charge state ions in electron cyclotron resonance ion sources (ECRISs) is dependent on the electron energy distribution (EED) within the source plasma. In order to better understand the EED, a measurement of electrons escaping axially from an ECRIS device has been performed at the National Superconducting Cyclotron Laboratory. Electrons were measured escaping from the Superconducting Source for Ions, driven at 18 GHz. Dependencies of the observed EED on the confining magnetic field strength and injected microwave power are reported. This paper focuses on large peaks of electrons in the 400–1200 keV energy range. Measurements of the axial bremsstrahlung spectrum have been simultaneously carried out to provide a direct comparison between both techniques. A comparison between the energy associated with the peak of the electron distribution and the spectral temperature of the bremsstrahlung distribution is shown. [ABSTRACT FROM AUTHOR]

The Space Environment Simulation and Research Infrastructure project, which uses various ion beams as irradiated materials in life science research, is being built at the Harbin Institute of Technology. A new room temperature electron cyclotron resonance ion source, the Lanzhou Electron Cyclotron Resonance Ion Source No. 5 (LECR5), has been designed and constructed. It is an intense, highly charged, heavy ion beam injector which generates ion beams from H to Bi, typically ∼50 eμA 209Bi32+. The LECR5 is designed to operate at microwave frequencies in the range of 14.5–18 GHz. The typical magnetic parameters are designed based on those optimized for SECRAL, which operates at 18 GHz. This paper presents the LECR5 ion source, its test bench, and the preliminary beam results. [ABSTRACT FROM AUTHOR]

Electron cyclotron resonance ion sources (ECRISs) are widely applied for ion beam applications, e.g., plasma processing, cancer therapy, and ion engine of an artificial satellite. In our ECRIS, we aim at producing and extracting various ion beams from this device, in particular, Xeq+ ion beams at low energy. In the aerospace engineering field, there are problems of accumulated damages on various component materials caused by low energy of Xe ions from the engine. There are not enough experimental sputtering data for satellite materials at the Xeq+ in the low energy region. Then, we are trying to investigate the sputtering yield experimentally by irradiating the low energy Xe ion beams. To perform this experiment, it is necessary to acquire a certain amount of beam current with low energy. Then, we generate the low energy ion beams by the following steps: First, the ion beams are extracted from the ECRIS at high voltage. Next, these are transported to an ion beam irradiation system (IBIS). Finally, the ion beams are decelerated by the deceleration voltage in the IBIS. We adjusted the beamline. We measure the characteristics of the transport efficiency and decelerated ion beam currents. In this paper, we describe the experimental setup using an existing ECRIS for decelerated heavy ion beams and the results of decelerated ion beam currents. [ABSTRACT FROM AUTHOR]

A 2.45 GHz microwave-driven ion source for the generation of multicharged ions has been designed and built at Peking University recently. The magnetic field configuration of this ion source is a minimum-B type with a combination of a hexapole field and an axial mirror field. Argon was selected as the first tested beam generated by this ion source. A 63 µA Ar4+ ion beam at 35 kV extraction voltage was obtained in the pulsed mode (50 Hz/500 µs). Without the hexapole magnetic field, the highest charge state was only Ar2+, and no Ar4+ ion beam was detected. The comparison between the two sets of experimental results with different magnetic configurations has proven the rationality of the production of multicharged ions with this ion source. Both experimental results and discussion will be presented in this paper. [ABSTRACT FROM AUTHOR]

Ion source development over the last 20 years at the IMP is reviewed. For versatile purposes, several types of ion sources have been involved in the research and development work at the IMP, i.e., the highly charged ECR (Electron Cyclotron Resonance) ion source, intense microwave ion source or the 2.45 GHz intense beam ECR ion source, and laser ion source (LIS). In the development of ECR ion sources, SECRAL (Superconducting ECR ion source with Advanced design in Lanzhou), Lanzhou ECR ion source, and Lanzhou all permanent magnet ECR ion source series have been made, which can cover the operation microwave frequency range of 10–28 GHz. The LIS with an Nd:YAG laser with a maximum output energy of 8 J in 8 ns pulse duration has been developed for very intense short pulse ion beams from solid materials such as C, Ti, Ni, Ag, and so on. Microwave ion sources have been built to produce intense pulsed or direct current beams from several mA to 100 mA for either high intensity accelerators or applications. This paper will give an overview of the high intensity ion source development at the IMP, especially on the recent progress and new results, such as the status of the fourth generation ECR ion source (first fourth generation ECR ion source), the production of recorded highly charged ion beams with SECRAL sources, key technology research studies, and so on. [ABSTRACT FROM AUTHOR]

An innovative 18 GHz HIISI (Heavy Ion Ion Source Injector) room temperature Electron Cyclotron Resonance (ECR) ion source (ECRIS) has been designed and constructed at the Department of Physics, University of Jyväskylä (JYFL), for the nuclear physics program of the JYFL Accelerator Laboratory. The primary objective of HIISI is to increase the intensities of medium charge states (M/Q ≅ 5) by a factor of 10 in comparison with the JYFL 14 GHz ECRIS and to increase the maximum usable xenon charge state from 35+ to 44+ to serve the space electronics irradiation testing program. HIISI is equipped with a refrigerated permanent magnet hexapole and a noncylindrical plasma chamber to achieve very strong radial magnetic confinement with Brad = 1.42 T. The commissioning of HIISI began in Fall 2017, and in Spring 2019, it has met the main objectives. As an example, the intensity of the Xe27+ ion beam has improved from 20 μA to 230 μA. In addition, the beam intensity of the Xe44+ ion beam has exceeded the requirement set by the irradiation testing program. The performance of HIISI is comparable to superconducting ECR ion sources with the same maximum microwave frequency of 18 GHz and a total power of 3 kW. For example, Ar16+ and Xe30+ ion beam intensities of 130 μA and 106 μA, respectively, have been obtained with a total microwave power of 3 kW distributed between 18, 17.4, and 14.5 GHz frequencies. The ion beams have been extracted through an 8 mm plasma electrode aperture using 15–17 kV extraction voltage. The latest development work, extracted ion beam intensities, special features, and future prospects of HIISI are presented in this paper. [ABSTRACT FROM AUTHOR]

The paper presents recent results of a "pointlike" neutron source development based on a D-D fusion in a D-loaded target caused by its bombardment with a sharply focused deuterium ion beam. These developments are undergoing at the Institute of Applied Physics of Russian Academy of Sciences in order to study a possibility to create an effective and compact device for fast-neutron radiography. The last experiments with a beam produced by a gasdynamic high-current ECR ion source and its focusing with a magnetic lens demonstrated that 60 mA of deuterium ions may be constricted to a transversal size of ∼1 mm at the focal plane. With a purpose to improve this result in terms of the beam current and its size, a combined electrostatic and magnetic focusing system is proposed and analyzed. It is shown that the combined system may enhance the total beam current and reduce its footprint down to 0.13 mm. All numerical analysis was performed using the IBSimu code. [ABSTRACT FROM AUTHOR]

The GTS-LHC ECR ion source (named after the Grenoble Test Source and the Large Hadron Collider) at CERN provides heavy ion beams for the chain of accelerators from Linac3 up to the LHC for high energy collision experiments and to the Super Proton Synchrotron for fixed target experiments. During the standard operation, the oven technique is used to evaporate lead into the source plasma to produce multiple charged lead ion beams. Intensity and stability are key parameters for the beam, and the operational experience is that some of the source instabilities can be linked to the oven performance. Over long operation periods of several weeks, the evaporation is not stable which makes the tuning of the oven unpredictable and nonreproducible. A dedicated test stand is used to study the oven performance and possible improvements independently of the source operation. It was observed that the measured evaporation rate of the oven can vary spontaneously in a wide range even when stable operating conditions are applied to the oven controls. Data collected at the test stand hint that these fluctuations are caused by temperature instabilities of the oven itself. Several ways to improve the oven stability were tested, including insulation changes and modifications of the oven crucible. Some of the most promising results regarding the stability of the evaporation will be presented in this paper. [ABSTRACT FROM AUTHOR]

According to the requirements of ion beams extracted from an electron cyclotron resonance ion source transverse phase space coupling research and the afterglow beam property effective measurement, a pepper pot type meter called PEMiL (Pepper Pot Emittance Meter in Lanzhou) has been designed, fabricated, and commissioned to obtain the emittance of high intensity highly charged heavy ion beams. The direct current beam emittance measurement results verify the coupling property caused by the semisolenoid field. This paper also describes the scheme of multiple exposure accumulation which was applied to measure the afterglow beam property, and the transverse phase space distribution of the oxygen afterglow beam which was measured for the first time is presented. [ABSTRACT FROM AUTHOR]

We have considered the accessibility condition of electromagnetic and electrostatic waves propagating in an electron cyclotron resonance (ECR) ion source (ECRIS) plasma and then investigated experimentally their correspondence relationships with production of multicharged ions. It has been clarified that there exists an efficient configuration of ECR zones for producing multicharged ion beams and has been suggested that a new resonance, i.e., upper hybrid resonance (UHR), must have occurred. We have been trying to perform advanced experiments with 4–6 GHz X-mode microwaves to the 2.45 GHz ECRIS plasma, and we have succeeded in enhancing the production of multicharged ions by launching X-mode microwaves of these bands. Furthermore, at the same time, we have observed sharp increases in electron energy distribution functions in the ECRIS plasma by means of probe methods. It has been concluded that the UHRs must have occurred when applying multiplex microwaves with their frequencies away from those frequencies for ECR in the ECRIS. In this paper, we will describe in brief the theoretical background and the results of these new experiments. [ABSTRACT FROM AUTHOR]

LAPECR3 (Lanzhou All Permanent magnet Electron cyclotron Resonance ion source No. 3) had been developed as an ion injector of Heavy Ion Medical Machine (HIMM) accelerator facility since 2009. The first HIMM accelerator facility was built in Wuwei city in 2015, and the LAPCER3 ion source has delivered C5+ ion beam to HIMM for more than 1000 days in the past four years. In order to improve the performance of the LAPECR3 ion source for intense carbon beams production, continuous research and development work has been made. The recently developed LAPECR3 ion source together with the new low-energy beam transportation can provide better performance in terms of both beam intensity and quality. This paper will generally review the LAPECR3 ion source operation status for HIMM, and the recent improvement will be presented, especially the stable beams production of C4+ and C5+. [ABSTRACT FROM AUTHOR]

The electron confinement in an electron cyclotron resonance ion source is considered a critical factor that has a great influence on the working efficiency. In this paper, a three-dimensional electromagnetic particle-in-cell code is presented for simulations of the electron confinement in minimum-B structures. Electron dynamics under the effect of electromagnetic fields is modeled through a leapfrog scheme by solving Maxwell's equations and the particle equations of motion iteratively. Some characteristics of electron magnetic confinement are obtained through a benchmarking example. Preliminary results of the simulation show good agreement with the well-known effects. [ABSTRACT FROM AUTHOR]

The Electron Cyclotron Resonance Ion Source (ECRIS) has transformed the nuclear physics research field over the last 47 years. Today, the performance of ion sources is the first parameter that defines the design performance of existing facilities as well as the design approach and performance of new facilities. In this paper, I will review the current "state of the art" performance capabilities for ECRISs as well as other ion sources and how those current capabilities form the primary design criteria for new nuclear physics facilities and set the limiting performance for existing facilities. I will close with a short-term look into the future for these ion sources and other competing types. [ABSTRACT FROM AUTHOR]

High Temperature Ovens (HTOs) have widely been used to evaporate refractory materials in electron cyclotron resonance ion sources to produce hundreds of microamperes of multiply and highly charged metal ion beams. To meet the demands of milliamperes of multiply charged uranium and other heavy metal ion beams for future accelerators, a new and low-cost HTO is under development at Lawrence Berkeley National Laboratory for better long-term stability at high evaporation rates. ANSYS simulations have been carried out to optimize the new HTO with low heating current to reduce the electromagnetic forces as an HTO is immersed in the strong ECRIS magnetic fields. A larger loading volume is employed to deal with higher material consumption. Off-line tests have shown that the unloaded new HTO operates stably up to 1800–1900 °C with low temperature gradients and good repeatability. This paper presents and discusses the conceptual design features of the new HTO and off-line tests. [ABSTRACT FROM AUTHOR]

The China Spallation Neutron Source started delivering neutron beams to users in March 2018. To upgrade the beam power to 500 kW and improve the performance of the ion source, an RF-driven negative hydrogen (H−) ion source is under development. The source has a silicon nitride ceramic plasma chamber surrounded by a 4.5-turn antenna. The plasma is ignited by a pulsed DC spark gap and then driven by a 2 MHz solid-state amplifier with a repetition rate of 25 Hz. The commissioning of the source started in January 2019. When uncesiated, it produced about 20 mA beam at an RF power of 32 kW and pulse width of 450 μs. This paper describes the configuration of the ion source, several peculiar technologies used in it, and the first negative hydrogen (H−) ion beam extraction. [ABSTRACT FROM AUTHOR]

This paper aims to summarize the developments of high current H2+ and H3+ ion sources in the past decades. The status of the H2+ and H3+ ion sources is discussed to show the attempts researchers made to improve the beam currents of H2+ and H3+. The results of the 2.45 GHz electron cyclotron resonance ion source named PMECR II at Peking University are presented, which may provide an alternative reference for the design and operation of high current H2+ and H3+ ion sources. [ABSTRACT FROM AUTHOR]

In the paper, the material science experiments, carried out recently using the Bio-Nano electron cyclotron resonance ion source (ECRIS) at Toyo University, are reported. We have investigated several methods to synthesize endohedral C60 using ion-ion and ion-molecule collision reaction in the ECRIS. Because of the simplicity of the configuration, we can install a large choice of additional equipment in the ECRIS. The Bio-Nano ECRIS is suitable not only to test the materials production but also to test technical developments to improve or understand the performance of an ECRIS. [ABSTRACT FROM AUTHOR]

This paper reports about a novel approach to the absolute intensity calibration of an electron cyclotron emission (ECE) spectroscopy system. Typically, an ECE radiometer consists of tens of separated frequency channels corresponding to different plasma locations. An absolute calibration of the overall diagnostic including near plasma optics and transmission line is achieved with blackbody sources at LN2 temperature and room temperature via a hot/cold calibration mirror unit. As the thermal emission of the calibration source is typically a few thousand times lower than the receiver noise temperature, coherent averaging over several hours is required to get a sufficient signal to noise ratio. A forward model suitable for any radiometer calibration using the hot/cold method and a periodic switch between them has been developed and used to extract the voltage difference between the hot and cold temperature source via Bayesian analysis. In contrast to the classical analysis which evaluates only the reference temperatures, the forward model takes into account intermediate effective temperatures caused by the finite beam width and thus uses all available data optimally. This allows the evaluation of weak channels where a classical analysis would not be feasible, is statistically rigorous, and provides a measurement of the beam width. By using a variance scaling factor, a model sensitive adaptation of the absolute uncertainties can be implemented, which will be used for the combined diagnostic Bayesian modeling analysis. [ABSTRACT FROM AUTHOR]

Electron cyclotron emission imaging (ECEI) diagnostic on Korean Superconducting Tokamak Advanced Research utilizes quasi-optical heterodyne-detection method to measure 2D (vertical and radial) Te fluctuations from two toroidally separated poloidal cross section of the plasma. A cylindrical lens local oscillator (LO) optics with optical path length (OPL) 2-2.5 m has been used in the current ECEI system to couple the LO source to the 24 vertically aligned array of ECE detectors. For efficient and compact LO optics employing the Powell lens is proposed so that the OPL of the LO source is significantly reduced from ~2.0 m to 0.4 m with new optics. The coupling efficiency of the LO source is expected to be improved especially at the edge channels. Results from the optical simulation together with the laboratory test of the prototype optics will be discussed in this paper. [ABSTRACT FROM AUTHOR]

The development of superconducting ECR source with higher magnetic fields and higher microwave frequency is the most straight forward path to achieve higher beam intensity and higher charge state performance. SECRAL, a superconducting third generation ECR ion source, is designed for 24-28 GHz microwave frequency operation with an innovative magnet configuration of sextupole coils located outside the three solenoids. SECRAL at 24 GHz has already produced a number of record beam intensities, such as 40Ar12+ 1.4 emA, 129Xe26+ 1.1 emA, 129Xe30+ 0.36 emA, and 209Bi31+ 0.68 emA. SECRAL-II, an upgraded version of SECRAL, was built successfully in less than 3 years and has recently been commissioned at full power of a 28 GHz gyrotron and three-frequency heating (28 + 45 + 18 GHz). New record beam intensities for highly charged ion production have been achieved, such as 620 eμA 40Ar16+, 15 eμA 40Ar18+, 146 eμA 86Kr28+, 0.5 eμA 86Kr33+, 53 eμA 129Xe38+, and 17 eμA 129Xe42+. Recent beam test results at SECRAL and SECRAL II have demonstrated that the production of more intense highly charged heavy ion beams needs higher microwave power and higher frequency, as the scaling law predicted. A 45 GHz superconducting ECR ion source FECR (a first fourth generation ECR ion source) is being built at IMP. FECR will be the world’s first Nb3Sn superconducting-magnet-based ECR ion source with 6.5 T axial mirror field, 3.5 T sextupole field on the plasma chamber inner wall, and 20 kW at a 45 GHz microwave coupling system. This paper will focus on SECRAL performance studies at 24-28 GHz and technical design of 45 GHz FECR, which demonstrates a technical path for highly charged ion beam production from 24 to 28 GHz SECRAL to 45 GHz FECR. [ABSTRACT FROM AUTHOR]

In the present paper, we describe a new home-built crossed-beam apparatus devoted to ion-induced ionization and fragmentation of isolated biologically relevant molecular systems. The biomolecular ions are produced by an electrospray ionization source, mass-over-charge selected, accumulated in a 3D ion trap, and then guided to the extraction region of an orthogonal time-of-flight mass spectrometer. Here, the target molecular ions interact with a keV atomic ion beam produced by an electron cyclotron resonance ion source. Cationic products from the collision are detected on a position sensitive detector and analyzed by time-of-flight mass spectrometry. A detailed description of the operation of the setup is given, and early results from irradiation of a protonated pentapeptide (leucine-enkephalin) by a 7 keV He+ ion beam are presented as a proof-of-principle. [ABSTRACT FROM AUTHOR]

Simulations predict that the concentric rings and the triangular structures in the profiles of strongly focused ion beams that are found in different experiments should be dominated by ion species with the same or at least similar m/q-ratio. To verify these theoretical predictions we have tuned our ECR ion source to deliver a beam consisting of multiple ion species whose particular m/q-depending focusing ranges from weakly focused to overfocused. We then recorded spatially resolved charge-state distributions of the beam profile at characteristic positions in the plane perpendicular to the beam line. The results validate theoretical predictions and are summarized in this paper. To achieve the required beam profile characteristics we moved the extraction along the beam line to achieve stronger focusing than by only changing the extraction voltage. To fit the regions of interest of the beam profile into the transmission area of the sector magnet, we steered the beam by moving the extraction in the plane perpendicular to the beam axis. The results of both investigations, beam focusing and beam steering by using a 3D-movable extraction, are also reported in this paper. A brief overview of the new beam monitor extensively used during these measurements, the Faraday cup array, is also given. [ABSTRACT FROM AUTHOR]

The Korea Basic Science Institute (KBSI) has been developing a heavy ion accelerator system to accelerate high current, multi-charge state ions produced by a 28 GHz superconducting electron cyclotron ion source. A beam analyzing system as a part of the low energy beam transport apparatus was developed to select charged particles with desirable charge states from the ion beams. The desired species of ion, which is generated and extracted from the ECR ion source including various ion particles, can be selected by 90° dipole electromagnet. Due to the non-symmetrical structure in the coil as well as the non-linear permeability of the yoke material coil, a three dimensional analysis was carried out to confirm the design parameters. In this paper, we present the experimental results obtained as result of an analysis of KBSI accelerator. The effectiveness of beam selection was confirmed during the test of the analyzing system by injecting an ion beam from an ECR ion source. [ABSTRACT FROM AUTHOR]

A 28 GHz electron cyclotron resonance (ECR) ion source is being developed for use as an injector for the superconducting linear accelerator of the Rare Isotope Science Project. Beam extraction from the ECR ion source has been simulated using the KOBRA3-INP software. The simulation software can calculate charged particle trajectories in three dimensional complex magnetic field structures, which in this case are formed by the arrangement of five superconducting magnets. In this study, the beam emittance is simulated to understand the effects of plasma potential, mass-to-charge ratio, and spatial distribution. The results of these simulations and their comparison to experimental results are presented in this paper. [ABSTRACT FROM AUTHOR]

In order to increase the intensity of the highly charged ions produced by the Electron Cyclotron Resonance Ion Sources (ECRISs), techniques like the frequency tuning and the afterglow mode have been developed and in this paper the effect on the ion production is shown for the first time when combining both techniques. Recent experimental results proved that the tuning of the operating frequency of the ECRIS is a promising technique to achieve higher ion currents of higher charge states. On the other hand, it is well known that the afterglow mode of the ECRIS operation can provide more intense pulsed ion beams in comparison with the continuous wave (cw) operation. These two techniques can be combined by pulsing the variable frequency signal driving the traveling wave tube amplifier which provides the high microwave power to the ECRIS. In order to analyze the effect of these two combined techniques on the ion source performance, several experiments were carried out on the pulsed frequency tuned CAPRICE (Compacte source A Plusiers Resonances Ionisantes Cyclotron Electroniques)-type ECRIS. Different waveforms and pulse lengths have been investigated under different settings of the ion source. The results of the pulsed mode have been compared with those of cw operation. [ABSTRACT FROM AUTHOR]

High performance electron cyclotron resonance (ECR) ion sources, such as VENUS (Versatile ECR for NUclear Science), produce large amounts of x-rays. By studying their energy spectra, conclusions can be drawn about the electron heating process and the electron confinement. In addition, the bremsstrahlung from the plasma chamber is partly absorbed by the cold mass of the superconducting magnet, adding an extra heat load to the cryostat. Germanium or NaI detectors are generally used for x-ray measurements. Due to the high x-ray flux from the source, the experimental setup to measure bremsstrahlung spectra from ECR ion sources is somewhat different from that for the traditional nuclear physics measurements these detectors are generally used for. In particular, the collimation and background shielding can be problematic. In this paper, we will discuss the experimental setup for such a measurement, the energy calibration and background reduction, the shielding of the detector, and collimation of the x-ray flux. We will present x-ray energy spectra and cryostat heating rates depending on various ion source parameters, such as confinement fields, minimum B-field, rf power, and heating frequency. [ABSTRACT FROM AUTHOR]

Recently the Versatile ECR for NUclear Science (VENUS) ion source was engaged in a 60-day long campaign to deliver high intensity 48Ca11+ beam to the 88-Inch Cyclotron. As the first long term use of VENUS for multi-week heavy-element research, new methods were developed to maximize oven to target efficiency. First, the tuning parameters of VENUS for injection into the cyclotron proved to be very different than those used to tune VENUS for maximum beam output of the desired charge state immediately following its bending magnet. Second, helium with no oxygen support gas was used to maximize the efficiency. The performance of VENUS and its low temperature oven used to produce the stable requested 75 eµA of 48Ca11+ beam current was impressive. The consumption of 48Ca in VENUS using the low temperature oven was checked roughly weekly, and was found to be on average 0.27 mg/h with an ionization efficiency into the 11+ charge state of 5.0%. No degradation in performance was noted over time. In addition, with the successful operation of VENUS the 88-Inch cyclotron was able to extract a record 2 pµA of 48Ca11+, with a VENUS output beam current of 219 eµA. The paper describes the characteristics of the VENUS tune used for maximum transport efficiency into the cyclotron as well as ongoing efforts to improve the transport efficiency from VENUS into the cyclotron. In addition, we briefly present details regarding the recent successful repair of the cryostat vacuum system. [ABSTRACT FROM AUTHOR]

The Kei-source is a compact electron cyclotron resonance ion source using only permanent magnets and a frequency of 10 GHz. It was developed at the National Institute of Radiological Sciences (NIRS) for producing C4+ ions oriented for high-energy carbon therapy. It has also been used as an ion source for the NIRS-930 cyclotron. Its microwave band region for the traveling-wave-tube amplifier and maximum output power are 8-10 GHz and 350 W, respectively. Since 2006, it has provided various ion beams such as proton, deuteron, carbon, oxygen, and neon with sufficient intensity (200 µAf o r proton and deuteron, 50 µAf o rC4+, for example) and good stability for radioisotope production, tests of radiation damage, and basic research experiments. Its horizontal and vertical emittances were measured using a screen monitor and waist-scan. The present paper reports the current status of the Kei-source. [ABSTRACT FROM AUTHOR]

The 320 kV platform for multi-discipline research with highly charged ions is a heavy ion beam acceleration instrument developed by Institute of Modern Physics, which is dedicated to basic scientific researches such as plasma, atom, material physics, and astrophysics, etc. The platform has delivered ion beams of 400 species for 36 000 h. The average operation time is around 5000 h/year. With the beams provided by the platform, lots of outstanding progresses were made in various research fields. The ion source of the platform is an all-permanent magnet electron cyclotron resonance ion source, LAPECR2 (Lanzhou All Permanent ECR ion source No. 2). The maximum axial magnetic fields are 1.28 T at injection and 1.07 T at extraction, and the radial magnetic field is up to 1.21 T at the inner wall of the plasma chamber. The ion source is capable to produce low, medium, and high charge state gaseous and metallic ion beams, such as H+, 40Ar8+, 129Xe30+, 209Bi33+, etc. This paper will present the latest result of LAPECR2 and the routine operation status for the high voltage platform. [ABSTRACT FROM AUTHOR]

The permanent magnet 2.45 GHz electron cyclotron resonance ion source at Peking University can produce more than 100 mA hydrogen ion beam working at pulsed mode. For the increasing requirements of cluster ions (H2+ and H3+) in linac and cyclotron, experimental study was carried out to further understand the hydrogen plasma processes in the ion source for the generation of cluster ions. The constituents of extracted beam have been analyzed varying with the pulsed duration from 0.3 ms to 2.0 ms (repetition frequency 100 Hz) at different operation pressure. The fraction of cluster ions dramatically increased when the pulsed duration was lower than 0.6 ms, and more than 20 mA pure H3+ions with fraction 43.2% and 40 mA H2+ ions with fraction 47.7% were obtained when the operation parameters were adequate. The dependence of extracted ion fraction on microwave power was also measured at different pressure as the energy absorbed by plasma will greatly influence electron temperature and electron density then the plasma processes in the ion source. More details will be presented in this paper. [ABSTRACT FROM AUTHOR]

Superconducting ECR ion sources can produce intense highly charged ion beams for the application in heavy ion accelerators. Superconducting Electron Resonance ion source with Advanced Design (SECRAL) is one of the few fully superconducting ECR ion sources that has been successfully built and put into routine operation for years. With enormous efforts and R&D work, promising results have been achieved with the ion source. Heated by the microwave power from a 7 kW/24 GHz gyrotron microwave generator, very intense highly charged gaseous ion beams have been produced, such as 455 eµA Xe27+, 236 eµA Xe30+, and 64 eµA Xe35+. Since heavy metallic ion beams are being more and more attractive and important for many accelerator projects globally, intensive studies have been made to produce highly charged heavy metal ion beams, such as those from bismuth and uranium. Recently, 420 eµA Bi30+ and 202 eµA U33+ have been produced with SECRAL source. This paper will present the latest results with SECRAL, and the operation status will be discussed as well. An introduction of recently started SECRAL II project will also be given in the presentation. [ABSTRACT FROM AUTHOR]

Radiation is an important issue, which should be carefully treated during the design and commissioning of an ion source. Measurements show that X-rays are generated around the ceramics column of an extraction system when the source is powered up to 30 kV. The X-ray dose increases greatly when a beam is extracted. Inserting the ceramic column into a metal vacuum box is a good way to block X-ray emission for those cases. Moreover, this makes the online test of an intense H+ ion beam with energy up to 100 keV possible. However, for deuteron ion source commissioning, neutron and gamma-ray radiation become a serious topic. In this paper, we will describe the design of the extraction system and the radiation doses of neutrons and gamma-rays measured at different D+ beam energy during our 2.45 GHz deuteron electron cyclotron resonance ion source commissioning for PKUNIFTY (PeKing University Neutron Imaging FaciliTY) project at Peking University. [ABSTRACT FROM AUTHOR]

The Electron Cyclotron Resonance Ion Sources (ECRISs) development is strictly related to the availability of new diagnostic tools, as the existing ones are not adequate to such compact machines and to their plasma characteristics. Microwave interferometry is a non-invasive method for plasma diagnostics and represents the best candidate for plasma density measurement in hostile environment. Interferometry in ECRISs is a challenging task mainly due to their compact size. The typical density of ECR plasmas is in the range 1011-1013 cm-3 and it needs a probing beam wavelength of the order of few centimetres, comparable to the chamber radius. The paper describes the design of a microwave interferometer developed at the LNS-INFN laboratories based on the so-called "frequency sweep" method to filter out the multipath contribution in the detected signals. The measurement technique and the preliminary results (calibration) obtained during the experimental tests will be presented. [ABSTRACT FROM AUTHOR]

The present paper summarizes the results obtained from the past few years in the framework of the Enhanced Multi-Ionization of short-Lived Isotopes for Eurisol (EMILIE) project. The EMILIE project aims at improving the charge breeding techniques with both Electron Cyclotron Resonance Ion Sources (ECRIS) and Electron Beam Ion Sources (EBISs) for European Radioactive Ion Beam (RIB) facilities. Within EMILIE, an original technique for debunching the beam from EBIS charge breeders is being developed, for making an optimal use of the capabilities of CW post-accelerators of the future facilities. Such a debunching technique should eventually resolve duty cycle and time structure issues which presently complicate the data-acquisition of experiments. The results of the first tests of this technique are reported here. In comparison with charge breeding with an EBIS, the ECRIS technique had lower performance in efficiency and attainable charge state for metallic ion beams and also suffered from issues related to beam contamination. In recent years, improvements have been made which significantly reduce the differences between the two techniques, making ECRIS charge breeding more attractive especially for CW machines producing intense beams. Upgraded versions of the Phoenix charge breeder, originally developed by LPSC, will be used at SPES and GANIL/SPIRAL. These two charge breeders have benefited from studies undertaken within EMILIE, which are also briefly summarized here. [ABSTRACT FROM AUTHOR]

Ahead of the commissioning schedule, installation of the first Electron Cyclotron Resonance (ECR) ion source in the front end area of the Facility for Rare Isotope Beam (FRIB) is planned for the end of 2015. Operating at 14 GHz, this first ECR will be used for the commissioning and initial operation of the facility. In parallel, a superconducting magnet structure compatible with operation at 28 GHz for a new ECR ion source is in development at Lawrence Berkeley National Laboratory. The paper reviews the overall work in progress and development done with ECR ion sources for FRIB. [ABSTRACT FROM AUTHOR]

One of the limiting factors for the full understanding of Electron Cyclotron Resonance Ion Sources (ECRISs) fundamental mechanisms consists of few types of diagnostic tools so far available for such compact machines. Microwave-to-plasma coupling optimisation, new methods of density overboost provided by plasma wave generation, and magnetostatic field tailoring for generating a proper electron energy distribution function, suitable for optimal ion beams formation, require diagnostic tools spanning across the entire electromagnetic spectrum from microwave interferometry to X-ray spectroscopy; these methods are going to be implemented including high resolution and spatially resolved X-ray spectroscopy made by quasi-optical methods (pin-hole cameras). The ion confinement optimisation also requires a complete control of cold electrons displacement, which can be performed by optical emission spectroscopy. Several diagnostic tools have been recently developed at INFN-LNS, including "volume-integrated" X-ray spectroscopy in low energy domain (2-30 keV, by using silicon drift detectors) or high energy regime (>30 keV, by using high purity germanium detectors). For the direct detection of the spatially resolved spectral distribution of X-rays produced by the electronic motion, a "pin-hole camera" has been developed also taking profit from previous experiences in the ECRIS field. The paper will give an overview of INFNLNS strategy in terms of new microwave-to-plasma coupling schemes and advanced diagnostics supporting the design of new ion sources and for optimizing the performances of the existing ones, with the goal of a microwave-absorption oriented design of future machines. [ABSTRACT FROM AUTHOR]

At Institute of Modern Physics (IMP), Chinese Academy of Sciences (CAS), the superconducting Electron Cyclotron Resonance (ECR) ion source SECRAL (Superconducting ECR ion source with Advanced design in Lanzhou) has been put into operation for about 10 years now. It has been the main working horse to deliver intense highly charged heavy ion beams for the accelerators. Since its first plasma at 18 GHz, R&D work towards more intense highly charged ion beam production as well as the beam quality investigation has never been stopped. When SECRAL was upgraded to its typical operation frequency 24 GHz, it had already showed its promising capacity of very intense highly charged ion beam production. And it has also provided the strong experimental support for the so called scaling laws of microwave frequency effect. However, compared to the microwave power heating efficiency at 18 GHz, 24 GHz microwave heating does not show the ω2 scale at the same power level, which indicates that microwave power coupling at gyrotron frequency needs better understanding. In this paper, after a review of the operation status of SECRAL with regard to the beam availability and stability, the recent study of the extracted ion beam transverse coupling issues will be discussed, and the test results of the both TE01 and HE11 modes will be presented. A general comparison of the performance working with the two injection modes will be given, and a preliminary analysis will be introduced. The latest results of the production of very intense highly charged ion beams, such as 1.42 emA Ar12+, 0.92 emA Xe27+, and so on, will be presented. [ABSTRACT FROM AUTHOR]

SECRAL (superconducting ECR ion source with advanced design in Lanzhou) ion source has been in routine operation for Heavy Ion Research Facility in Lanzhou (HIRFL) accelerator complex since May 2007. To further enhance the SECRAL performance in order to satisfy the increasing demand for intensive highly charged ion beams, 3-5 kW high power 24 GHz single frequency and 24 GHz +18 GHz double frequency with an aluminum plasma chamber were tested, and some exciting results were produced with quite a few new record highly charged ion beam intensities, such as 129Xe35+ of 64 eμA, 129Xe42+ of 3 eμA, 209Bi41+ of 50 eμA, 209Bi50+ of 4.3 eμA and 209Bi54+ of 0.2 eμA. In most cases SECRAL is operated at 18 GHz to deliver highly charged heavy ion beams for the HIRFL accelerator, only for those very high charge states and very heavy ion beams such as 209Bi36+ and 209Bi41+, SECRAL has been operated at 24 GHz. The total operation beam time provided by SECRAL up to July 2011 has exceeded 7720 hours. In this paper, the latest performance, development, and operation status of SECRAL ion source are presented. The latest results and reliable long-term operation for the HIRFL accelerator have demonstrated that SECRAL performance for production of highly charged heavy ion beams remains improving at higher RF power with optimized tuning. [ABSTRACT FROM AUTHOR]

LECR4 (Lanzhou electron cyclotron resonance ion source No. 4) has been successfully constructed at IMP and has also been connected with the Low Energy Beam Transport (LEBT) and Radio Frequency Quadrupole (RFQ) systems. These source magnet coils are cooled through evaporative cooling technology, which is the first attempt with an ECR ion source in the world. The maximum mirror field is 2.5 T (with iron plug) and the effective plasma chamber volume is 1.2 l. It was designed to be operated at 18 GHz and aimed to produce intense multiple charge state heavy ion beams for the linear injector project SSC-Linac at IMP. In February 2014, the first analyzed beam at 18 GHz was extracted. During about three months' commissioning, some outstanding results have been achieved, such as 1.97 emA of O6+, 1.7 emA of Ar8+, 1.07 emA of Ar9+, and 118 euA of Bi28+. The source has also successfully delivered O5+ and Ar8+ ion beams for RFQ commissioning in April 2014. This paper will give a brief overview of the design of LECR4. Then, the latest results of this source at 18 GHz will be presented. [ABSTRACT FROM AUTHOR]

At the China Institute of Atomic Energy, a central region model cyclotron has been constructed, which is dedicated for various experimental verifications to study beam properties. The design features of the ion source and injection line have already been described in other papers. We shall report here the results of the initial beam tests. A wire scanner is employed in the injection line to measure beam transverse sizes and these data can be used to fit the phase plane parameters after the ion source. Based on the beam tests results, the ion source built in 2003 has been improved recently. The improvement is mainly due to the repair of the multicusp field. From the ion source to the exit of the inflector, a transmission efficiency of 93% has been obtained for a continuous and low current input beam. It is also described here the experimental arrangement and the results. [ABSTRACT FROM AUTHOR]