Search

We report on the cross-calibration of Thomson Parabola (TP) and Time-of-Flight (TOF) detectors as particle diagnostics, implemented on the most recent setup of the ALLS 100 TW laser-driven ion acceleration beamline. The Microchannel Plate (MCP) used for particle detection in the TP spectrometer has been calibrated in intensity on the tandem linear accelerator at the Université de Montréal. The experimental data points of the scaling factor were obtained by performing a pixel cluster analysis of single proton impacts on the MCP. A semi-empirical model was extrapolated and fitted to the data to apply the calibration also to higher kinetic energies and to extend it to other ion species. Two TOF lines using diamond detectors, placed at +6° and −9° with respect to the target-normal axis, were benchmarked against the TP spectrometer measurements to determine the field integrals related to its electric and magnetic dispersions. The mean integral proton numbers obtained on the beamline were about 4.1 × 1011 protons/sr with a standard deviation of 15% in the central section of the spectrum around 3 MeV, hence witnessing the high repeatability of the proton bunch generation. The mean maximum energy was of 7.3 ± 0.5 MeV, well in agreement with similar other 100 TW-scale laser facilities, with the best shots reaching 9 MeV and nearly 1012 protons/sr. The used particle diagnostics are compatible with the development of a high-repetition rate targetry due to their fast online readout and are therefore a crucial step in the automation of any beamline. [ABSTRACT FROM AUTHOR]

We have developed a laser wakefield generated X-ray probe to directly measure the temporal evolution of the ionization states in warm dense aluminum by means of absorption spectroscopy. As a promising alternative to the free electron excited X-ray sources, Betatron X-ray radiation, with femtosecond pulse duration, provides a new technique to diagnose femtosecond to picosecond transitions in the atomic structure. The X-ray probe system consists of an adjustable Kirkpatrick-Baez (KB) microscope for focusing the Betatron emission to a small probe spot on the sample being measured, and a flat Potassium Acid Phthalate Bragg crystal spectrometer to measure the transmitted X-ray spectrum in the region of the aluminum K-edge absorption lines. An X-ray focal spot size of around 50 μm was achieved after reflection from the platinum-coated 10-cm-long KB microscope mirrors. Shot to shot positioning stability of the Betatron radiation was measured resulting in an rms shot to shot variation in spatial pointing on the sample of 16 μm. The entire probe setup had a spectral resolution of ∼1.5 eV, a detection bandwidth of ∼24 eV, and an overall photon throughput efficiency of the order of 10-5. Approximately 10 photons were detected by the X-ray CCD per laser shot within the spectrally resolved detection band. Thus, it is expected that hundreds of shots will be required per absorption spectrum to clearly observe the K-shell absorption features expected from the ionization states of the warm dense aluminum. [ABSTRACT FROM AUTHOR]

Recent progress in high intensity ultrafast laser systems provides the opportunity to produce laser plasma x-ray sources exhibiting broad spectrum and high average x-ray flux that are well adapted to x-ray absorption measurements. In this paper, the development of a laser based x-ray absorption near edge structure (XANES) beamline exhibiting high repetition rate by using the Advanced Laser Light Source (ALLS) facility 100 Hz laser system (100 mJ, 35 fs at 800 nm) is presented. This system is based on a broadband tantalum solid target soft x-ray source and a grazing incidence grating spectrometer in the 1–5 nm wavelength range. To demonstrate the high potential of this laser based XANES technique in condensed matter physics, material science, or biology, measurements realized with several samples are presented: VO2 vanadium L edge, Si3N4 nitrogen K edge, and BPDA/PPD polyimide carbon K edge. The characteristics of this laser based beamline are discussed in terms of brightness, signal to noise ratio, and compared to conventional synchrotron broadband x-ray sources which allow achieving similar measurements. Apart from the very compact size and the relative low cost, the main advantages of such a laser based soft x-ray source are the picosecond pulse duration and the perfect synchronization between this x-ray probe and a laser pulse excitation which open the way to the realization of time resolved x-ray absorption measurements with picosecond range time resolution to study the dynamics of ultrafast processes and phase transition. [ABSTRACT FROM AUTHOR]

We demonstrate the feasibility of phase-contrast imaging with an ultrafast laser-based hard x-ray source. Hard x rays are generated during the interaction of a high-intensity femtosecond laser pulse (10 TW, 60 fs, 10 Hz) focused onto solid target in a very small spot (3 μm diam). Such a novel x-ray source has a number of advantages over other sources previously used for phase-contrast imaging: It is very compact and much cheaper than a synchrotron, it has higher power and better x-ray spectrum control than a microfocal x-ray tube, and it has much higher repetition rate than an x-pinch source. The Kα line at 17 keV produced using a solid Mo target, and the in-line imaging geometry have been utilized in this study. Phase-contrast images of test objects and biological samples have been realized. The characteristics of the images are the significant enhancement of interfaces due to an x-ray phase shift that reveal details that were hardly observable, or even undetectable, in absorption images and suppression of optically dense structures well defined in the absorption images. Our study indicates that the absorption and the phase-contrast images obtained with an ultrafast laser-based x-ray source provide complementary information about the imaged objects, thus enriching our arsenal of research tools for laboratory or clinic-based biomedical imaging. [ABSTRACT FROM AUTHOR]

Laser-driven proton accelerators are relevant candidates for many applications such as material science or medicine. Today, there are multi-hundred-TW table-top laser systems that can generate relativistic peak intensities >1018 W/cm2 and routinely reach proton energies in the MeV range. However, for most desired applications, there is still a need to optimize the quality and stability of the laser-generated proton beam. In this work, we developed a 0.625 Hz high repetition-rate setup in which a laser with 2.5% RMS energy stability is irradiating a solid target with an intensity of 1019 to 1020 W/cm2 to explore proton energy and yield variations, both with high shot statistics (up to about 400 laser shots) and using different interaction targets. Investigating the above-mentioned parameters is important for applications that rely on specific parts of the proton spectrum or a high ion flux produced over quick multi-shot irradiation. We demonstrate that the use of a stable "multi-shot mode" allows improving applications, e.g., in the detection of trace elements using laser-driven particle-induced x-ray emission., (© 2023 Author(s). Published under an exclusive license by AIP Publishing.)