Search

To face the climate change and carbon neutrality, reductions of energy-uses and carbon emissions are imminent. Pipe-encapsulated phase change material (PenPCM) wall is a novel envelope system with renewable energy utilizations in buildings. It combines the PCMs, nocturnal radiant cooler and gravity heat-pipe with the wall to achieve the automatic heat insulation and removal without the mechanical energy. Parameters may have influences on system performances and the parametric analysis is understudied. In this study, the influences of parameters including phase-change temperature, PCM thickness, pipe-spacings, cooler areas and orientations are investigated. The system applicability for different climate regions is also studied. Results show that, when the phase-change temperature is 27–29 °C, the ratio of the cooling load reduction to the cooling load of the conventional wall reaches largest with 17.4%. Appropriately increasing the PCM quantity can improve the thermal-storage capacity and decrease the wall temperature fluctuation. Enlarging the cooler area can increase the energy-saving effect of the PenPCM wall system. For different climate regions, the PenPCM wall system is applicable. Compared with conventional wall, the ratio of the cooling load reduction from June to September can reach 11.7%, 16.1%, 21.1%, 28.6%, 44.2% respectively for Hong Kong, Wuhan, Beijing, Harbin and Kunming. [ABSTRACT FROM AUTHOR]

Aiming at reducing the heating and cooling loads for built environments, the thermal resistance and capacitance (R C) model has widely been acknowledged as an effective method for predicting the heat flux through building walls by simplifying wall structures and their properties into R and C allocations. This paper demonstrates an inverse optimization method based on particle swarm optimization (PSO) for determining the optimal R C allocation that minimizes the heat flux through building walls. A thermal R C model with three resistances and two capacitances was used as an example to search for the optimal building R C allocation in the hot summer and warm winter zone of China. The inverse optimization could be efficiently accomplished in 2.5 h with an ordinary computer, approximately 0.12% of the time consumed by using the exhaustive search method. The optimized R C allocation was composed of three resistances of 0.43, 0.18 and 0.39 and two capacitances of 0.50 and 0.50. Compared to the three typical thermal insulation (e.g., internal, external, and internal/external), the optimal R C allocation could reduce the heat flux into/from buildings by 17.3%–44.3%. The proposed inverse PSO method shows an effective and efficient capacity in searching for the optimal R C allocation of thermal R C models. • An inverse PSO method for the optimal RC allocation is proposed. • Optimization shows fewer steps and less time cost. • An optimal RC allocation is obtained. • Heat flux is reduced by 17.3%, 34.9% and 44.3% than three traditional RC allocations. • The effect mechanism of RC allocation on heat flux is explored. [ABSTRACT FROM AUTHOR]

Pipe-encapsulated PCM wall system with self-activated heat removal by nocturnal sky radiation cooler is a feasible means for building insulation and heat removal by using natural energy. In this paper, a system simulation platform including the simplified pipe-encapsulated PCM wall model, heat pipe heat-transfer model and nocturnal radiation model are established to investigate the thermal performance of the pipe-encapsulated PCM wall system with self-activated heat removal by a nocturnal sky radiation cooler. The temperature and heat flow of this system used in light-weight, medium-weight and heavy-weight walls under a dynamic boundary condition are respectively simulated on this platform. Results show that about 55.6%–82.8% of heat from the outdoor can be resisted by the pipe-encapsulated PCM wall, and 54.7%∼81.0% of that can be removed by the nocturnal radiation cooler at night. Comparing with the common wall, the proposed system can reduce by 32.4%∼55.5% of the accumulated heat entering into indoor environment. Good energy-saving potential can be achieved by this pipe-encapsulated PCM wall system. Besides, the result further reveals that the reduction of the accumulated internal surface heat transfer of this system used in medium-weight and heavy-weight walls is obvious larger than that of this system used in light-weight wall. • System platform of a pipe-encapsulated PCM wall system with heat removal. • Thermal performance of three walls (light, medium, heavy) with the PCM wall system. • 55.6%–82.8% of heat from the outdoor can be resisted by the PCM wall system. • Reduction of heat into the indoor is lager for the heavy wall with the PCM system. [ABSTRACT FROM AUTHOR]