Search

The alternation between cloudy and clear skies alters the photovoltaic production. This makes it necessary to anticipate these disturbances hours in advance for the correct operation of the electricity distribution plants and networks. In this paper, two short-term forecasting models (3 h) are developed to forecast the photovoltaic production in an integrated plant in the CIESOL building of the University of Almería. The methodology used is based on sky camera images and Artificial Intelligence techniques. Two models have been developed and compared applying artificial neural network (ANN) and support vector machine (SVM) techniques. The global irradiance predicted using sky camera images is used as an input variable in both models. In addition, the operational status of the plants has been included as an input parameter through the performance ratio. The results have shown that the errors made by ANN and SVM are very similar. For all sky conditions, the uncertainty of the production forecast differs by less than 2% from the uncertainty of the solar resource, which is the main source of error in the production models developed. [ABSTRACT FROM AUTHOR]

Solar cells lose efficiency as the operating temperature increases under normal operating conditions, resulting in a very significant power output reduction. This issue is most relevant in areas with the highest photovoltaic energy harvesting potential, where irradiance and ambient temperature are particularly high. A novel cooling system for commercial photovoltaic modules based on low-enthalpy geothermal cooling is proposed in this paper. Excess heat is evacuated from the solar module in a clean and efficient manner by a single-phase and close-loop cooling circuit that uses the underground as a natural heatsink. In addition, a thermoelectrical theoretical model is presented, that allows the optimization of the flowrate and the maximization of the extra power generation of the cooled module. A prototype was manufactured and tested in outdoor conditions in September 2021 in Spain. Test results are in good agreement with the theoretical model, which has been used for prediction of the performance of the system for a typical meteorological year in the region. A peak efficiency improvement of 10.7% is calculated for the month of July, with an optimal flowrate of 1.8 l/min per square meter of solar module. A yearly weighted average power gain of up to 4.9% is also calculated. [ABSTRACT FROM AUTHOR]

Fluctuations of the incoming solar irradiance impact the power generation from photovoltaic and concentrating solar thermal power plants. Accurate solar nowcasting becomes necessary to detect these sudden changes of generated power and to provide the desired information for optimal exploitation of solar systems. In the framework of the International Energy Agency's Photovoltaic Power Systems Program Task 16, a benchmarking exercise has been conducted relying on a bouquet of solar nowcasting methodologies by all-sky imagers (ASI). In this paper, four ASI systems nowcast the Global Horizontal Irradiance (GHI) with a time forecast ranging from 1 to 20 min during 28 days with variable cloud conditions spanning from September to November 2019 in southern Spain. All ASIs demonstrated their ability to accurately nowcast GHI, with RMSE ranging from 6.9% to 18.1%. Under cloudy conditions, all ASIs' nowcasts outperform the persistence models. Under clear skies, three ASIs are better than persistence. Discrepancies in the observed nowcasting performance become larger at increasing forecast horizons. The findings of this study highlight the feasibility of ASIs to reliably nowcast GHI at different sky conditions, time intervals and horizons. Such nowcasts can be used either to estimate solar power at distant times or detect sudden GHI fluctuations. • ASI-based GHI nowcasts outperform persistence model under cloudy conditions. • Under clear skies, three ASIs reveal more accurate nowcasts than persistence. • ASIs forecasts are more accurate from persistence at increasing forecast horizons. [ABSTRACT FROM AUTHOR]

This paper aims to carry out an integrated Life Cycle Assessment to evaluate the environmental performance of retrofitting an existing first-generation ethanol plant for sustainable aviation fuel production. Two scenarios are defined, considering: (i) the incorporation of an alcohol-to-jet conversion pathway into a current bioethanol plant in Spain to produce synthetic paraffinic kerosene with aromatics biofuel, and (ii) the operation of two different plants, namely, an existing bioethanol production facility and a new-build ATJ plant. Results indicate that the global warming impact associated with the retrofitting of the bioethanol facility is 44.15 gCO 2eq per MJ of final fuels produced. The main GHG impact is associated with the operation of both the cogeneration system (∼42 %) and the natural gas boilers (∼25 %) to cover the heat and power requirements of the bioethanol facility. Findings concerning the climate change impact of the new-build ATJ plant exhibit analogous behavior; the GHG impact is estimated at 44.53 gCO 2eq /MJ fuels. Future electricity supply mixes with high shares of renewables could lead to substantially lower GHG emissions (up to 61 %) in aviation fuel production, as compared to conventional jet fuels. The replacement of natural gas with sustainable alternatives could further decrease the global warming impact up to 97 %. [ABSTRACT FROM AUTHOR]

Solar PV technologies have been expanding rapidly, and the installed power has increased, especially in the last decade. Their inclusion in university buildings arises as a key factor for sustainable transition in cities, since they have an important potential as case studies for urban experimentation positive effects on students and other stakeholders. This paper proposes a method to determine the availability for installing solar PV in universities' rooftops, considering simulation and cartography data, together with a final experimental validation stage. Unavailable areas for each rooftop are determined, including obstacles, the inner use of the rooftop and shadowed areas. Finally, the method verifies the technical suitability for all the proposed scenarios and applies an economic-environmental multicriteria evaluation to select the most suitable one. The methodology is validated in the Universitat Politècnica de València Vera-Campus. In total, 88913 m2 of the rooftops are suitable for solar PV incorporation, representing 48 % of the total surface. 52 % of the solar PV installable capacity takes place in surfaces which can incorporate more than 100 kW, 20.6 % between 50 and 100 kW and 27.4 % less than 50 kW. Finally, the multicriteria evaluation proved that the scenario with all the possible installations is the most suitable one. [ABSTRACT FROM AUTHOR]

Heating up of photovoltaic modules during operation results in a significant power output reduction. This effect is especially relevant in regions with the highest photovoltaic potential, where irradiance and ambient temperature are particularly high. In this paper, a novel low enthalpy geothermal cooling system that improves the efficiency of a commercial solar module is described and experimentally validated. Two heat exchangers, one attached to the backside of the module, and another introduced inside a 15 m deep borehole, are connected in a closed circuit. A water-based coolant is pumped through the system, evacuating the excess heat from the module, and dissipating it underground in a clean and efficient manner, without additional water consumption after filling the system. The performance of the cooling system was experimentally tested by implementing it, for the first time, in a single-axis solar tracking isolated photovoltaic facility. Extensive tests were carried out in Spain, between September 2021 and August 2022 under a wide variety of environmental conditions. The efficiency improvement system has demonstrated its technical feasibility over a one-year period, showing a peak net efficiency improvement up to 13.4 %. Moreover, a positive net efficiency improvement has been demonstrated all year long, even during the winter months. [ABSTRACT FROM AUTHOR]

This paper proposes the first application of a split-range control technique on a concentrating solar collector to improve an absorption plant production. Solar absorption plants have solar power availability in phase with cooling demand under design conditions. Thus, it is a powerful cooling technology in the context of renewable energy and energy efficiency. These plants need control systems to cope with solar irradiance intermittency, reject irradiation disturbances, manage fossil fuels backup systems and dump closed-loop thermal-hydraulic oscillations. In this work, control techniques are proposed and simulated in an absorption plant in Spain. The plant consists of a concentrating Fresnel solar collector connected to an absorption chiller. The objectives are to operate with 100% renewable solar energy and avoid safety defocus events while reducing temperature oscillations and control actuators effort. Firstly, the current available plant controllers are defined, then two modifications are proposed. The first modification is a split-range controller capable of manipulating both flow and defocus of the Fresnel collector, the second modification is a PI controller to substitute the original chiller on-off controller. The results compare, through validated models, the different control systems and indicate that using both proposed controllers reduces 94% of the sum of actuators effort and 43% of the integral of absolute set-point tracking error compared to the plant's factory pre-set controllers. The suggested controllers increase 66% of energy production and 63% of exergy production. Besides, the split-range technique can be extended to any concentrating solar collector control. [Display omitted] [ABSTRACT FROM AUTHOR]

The paper aims to develop a decision tool for planning offshore wind farm locations, combining multi-criteria decision analysis and geographic information systems. This method considers several technological, environmental, social, and economic criteria. The criteria are used as evaluation factors and constraints to rank the identified potential locations through an Analytic Hierarchy Process. During the evaluation of the available areas, a pairwise comparison is used in which a group of experts determines the weights. Sensitivity and consensus analyses evaluate the results robustness. The methodology is developed for a case study in the Atlantic coastal areas of Portugal, Spain, and France. The results show the potential of this tool to support the planners in the designation of regions for floating wind farm development. [ABSTRACT FROM AUTHOR]

Extreme Wind Speed events (EWS) are responsible for the worst damages caused by wind in wind farms. An accurate estimation of the frequency and intensity of EWS is essential to avoid wind turbine damage and to minimize cut-out events in these facilities. In this paper we discuss how generative Data Augmentation (DA) techniques improve the performance of Machine Learning (ML) and Deep Learning (DL) algorithms in EWS prediction problems. These problems are usually tackled as classification tasks, which are highly unbalanced due to the small number of EWS events in wind farms. Different versions of Variational AutoEncoders (VAE) are proposed and analysed in this work (VAEs, Conditional VAEs (CVAEs) and Class-Informed VAEs (CI-VAE)) as generative DA techniques to balance the data in EWS problems, leading to better performance of the prediction systems. The proposed generative DA techniques have been compared against traditional DA algorithms in a real problem of EWS prediction in Spain, considering ERA5 reanalysis data as predictive variables. The results showed that the CI-VAE with a Convolutional Neural Network approach obtained the best results, with values of Precision 0.62, Recall 0.74 and F1 score 0.67, improving up to 4% the results of the method without data augmentation techniques. [Display omitted] • Generative data augmentation techniques can improve extreme wind prediction. • Variational Autoencoders modifications are used to generate synthetic wind extreme samples. • Experiments on real wind speed data from a Spanish wind farm are presented. • Comparisons with traditional data augmentation techniques show prediction improvements. [ABSTRACT FROM AUTHOR]

Finding an optimal bidding strategy for a wind farm in the electricity market is not straightforward due to the wind variability. This issue is becoming more relevant as renewable plants are more exposed to market signals. Considering the characteristics of the European markets, operators must submit the energy bidding between 12 and 36 h ahead the actual delivery time. This bidding can be adjusted later in any session of the intraday markets, but sometimes this is not enough to reduce significantly the deviation risk. This paper presents a practical application of a method to analytically calculate the optimal bidding of a wind power plant, based on the maximisation of the income function. The results show that, given the characteristics of the deviation markets in Spain, the optimal bidding strategy depends essentially on the deviation of the system. The proposed technique has been tested and validated in a real application by considering actual data for energy production and forecasts for an operating wind farm in Spain, as well as real market deviations and prices provided by the Spanish system and market operators; analysing the advantages of the proposed optimal bidding strategy over the most plausible option, based on bidding the forecasted energy. [ABSTRACT FROM AUTHOR]

This paper presents a model for optimizing the life cycle economic and environmental impacts of a hybrid renewable energy and battery storage system – as energy supply technologies (EST) for off-grid farms. Micro-hydropower and photovoltaics represent the primary renewable energy (RE) sources, with batteries and a diesel generator considered as possible back-up systems. A modified Non-dominated Sorting Genetic Algorithm II (NSGA-II) was developed and applied to a case study farm in Southern Spain and provided different EST solutions to optimize a design based on economic (life cycle costing or LCC) and environmental (life cycle assessment or LCA) constraints. The results highlighted that cases with a strong dependence on batteries could achieve minimum costs and lower impacts for climate change and energy resources (non-renewable fuels). In contrast, the optimal system for minimizing the consumption of material resources (metals/minerals) resulted in higher fuel use, which was up to 25% more expensive. The optimal EST solutions used up to 37% of the total energy generated; however, the results were sensitive to energy production-demand distributions. This methodology can help identify the most cost-effective solutions with the lower environmental impacts for decarbonizing the agricultural sector. [Display omitted] [ABSTRACT FROM AUTHOR]

The practical feasibility to install solar updraft tower (SUT) for power production require huge capital investment and difficulties in installing tall giant chimney structure. The chimney is the most expensive element of SUT and typically covers one-fourth of the total SUT cost. Previous finding has shown that a divergent chimney shows significant increase in power output than a conventional design for the same height. This paper deals with the unexplored scientific question: for how much height of divergent chimney can be dispensed with for the same or higher performance of a conventional design? Using an experimentally validated numerical model, we systematically investigated height reduction of chimney (and hence substantial cost) of a high performing divergent chimney whose power output is identical with a long unstable costly conventional cylindrical chimney. The conventional cylindrical design was chosen as the conventional SUT prototype installed at Manzanares, Spain in the year 1980. Results show that it is possible to reduce the vertical limit by about 80% of the height of conventional cylindrical chimney. Further, the cost analysis estimated for each SUT designs and the optimum divergent chimney SUT holds payback period 40% less than the conventional SUT. The proposed designs would be useful for floating chimney as well made of fabric material with light density air filled to keep short chimney height upright vertically to resolve the instability issues with the conventional tall chimney structure during high wind speed environmental conditions The present investigation would assist scientific community to develop more advance clean energy-based power generation systems to achieve net-zero carbon emissions targets. [Display omitted] [ABSTRACT FROM AUTHOR]