Search

The non-scanning radiometer with short-wavelength (SW: 0.2–5.0 μm) and total-wavelength (TW: 0.2–50.0 μm) channels is the primary payload of the Integrated Earth–Moon Radiation Observation System (IEMROS), which is designed to provide comprehensive Earth radiation measurements and lunar calibrations at the L1 Lagrange point of the Earth–Moon system from a global perspective. This manuscript introduces a radiometer preflight calibration methodology, which involves background removal and is validated using accurate and traceable reference sources. Simulated Earth view tests are performed to evaluate repeatability, linearity, and gain coefficients over the operating range. Both channels demonstrate repeatability uncertainties better than 0.34%, indicating consistent and reliable measuring performance. Comparative polynomial regression analysis confirms significant linear response characteristics with two-channel nonlinearity less than 0.20%. Gain coefficients are efficiently determined using a two-point calibration approach. Uncertainty analysis reveals an absolute radiometric calibration accuracy of 0.97% for the SW channel and 0.92% for the TW channel, underscoring the non-scanning radiometer's capability to provide dependable global Earth radiation budget data crucial to environmental and climate studies. [ABSTRACT FROM AUTHOR]

The IMERG data product is an optimal combination of precipitation estimates from the Global Precipitation Mission (GPM), making use of a variety of data types, primarily data from various spaceborne passive instruments. Previous versions of the IMERG product have been extensively validated by comparisons with gauge data and ground-based radars over land. However, IMERG rain rates, especially sub-daily, over open ocean are less validated due to the scarcity of comparison data, particularly with the relatively new Version 07. To address this issue, we consider IMERG V07 30-min data acquired in tropical cyclones over open ocean. We perform two tasks. The first is a straightforward comparison between IMERG precipitation rates and those retrieved from the GPM Dual-frequency Precipitation Radar (DPR). From this, we find that IMERG and DPR are close at low rain rates, while, at high rain rates, IMERG tends to be lower than DPR. The second task is the assessment of IMERG's ability to represent or detect structures commonly seen in tropical cyclones, including the annular structure and concentric eyewalls. For this, we operate on IMERG data with many machine learning algorithms and are able to achieve a 96% classification accuracy, indicating that IMERG does indeed contain TC structural information. [ABSTRACT FROM AUTHOR]

Climate change is undeniably one of the most pressing and critical challenges facing humanity in the 21st century. In this context, monitoring the Earth's Energy Imbalance (EEI) is fundamental in conjunction with greenhouse gases (GHGs) in order to comprehensively understand and address climate change. The French Uvsq-Sat NG pathfinder mission addresses this issue through the implementation of a Six-Unit CubeSat, which has dimensions of 111.3 × 36.6 × 38.8 cm in its unstowed configuration. Uvsq-Sat NG is a satellite mission spearheaded by the Laboratoire Atmosphères, Observations Spatiales (LATMOS), and supported by the International Satellite Program in Research and Education (INSPIRE). The launch of this mission is planned for 2025. One of the Uvsq-Sat NG objectives is to ensure the smooth continuity of the Earth Radiation Budget (ERB) initiated via the Uvsq-Sat and Inspire-Sat satellites. Uvsq-Sat NG seeks to achieve broadband ERB measurements using state-of-the-art yet straightforward technologies. Another goal of the Uvsq-Sat NG mission is to conduct precise and comprehensive monitoring of atmospheric gas concentrations (CO 2 and CH 4 ) on a global scale and to investigate its correlation with Earth's Outgoing Longwave Radiation (OLR). Uvsq-Sat NG carries several payloads, including Earth Radiative Sensors (ERSs) for monitoring incoming solar radiation and outgoing terrestrial radiation. A Near-Infrared (NIR) Spectrometer is onboard to assess GHGs' atmospheric concentrations through observations in the wavelength range of 1200 to 2000 nm. Uvsq-Sat NG also includes a high-definition camera (NanoCam) designed to capture images of the Earth in the visible range. The NanoCam will facilitate data post-processing acquired via the spectrometer by ensuring accurate geolocation of the observed scenes. It will also offer the capability of observing the Earth's limb, thus providing the opportunity to roughly estimate the vertical temperature profile of the atmosphere. We present here the scientific objectives of the Uvsq-Sat NG mission, along with a comprehensive overview of the CubeSat platform's concepts and payload properties as well as the mission's current status. Furthermore, we also describe a method for the retrieval of atmospheric gas columns (CO 2 , CH 4 , O 2 , H 2 O) from the Uvsq-Sat NG NIR Spectrometer data. The retrieval is based on spectra simulated for a range of environmental conditions (surface pressure, surface reflectance, vertical temperature profile, mixing ratios of primary gases, water vapor, other trace gases, cloud and aerosol optical depth distributions) as well as spectrometer characteristics (Signal-to-Noise Ratio (SNR) and spectral resolution from 1 to 6 nm). [ABSTRACT FROM AUTHOR]

The IMERG data product is an optimal combination of precipitation estimates from the Global Precipitation Mission (GPM), making use of a variety of data types, primarily data from various spaceborne passive instruments. Previous versions of the IMERG product have been extensively validated by comparisons with gauge data and ground-based radars over land. However, IMERG rain rates, especially sub-daily, over open ocean are less validated due to the scarcity of comparison data, particularly with the relatively new Version 07. To address this issue, we consider IMERG V07 30-min data acquired in tropical cyclones over open ocean. We perform two tasks. The first is a straightforward comparison between IMERG precipitation rates and those retrieved from the GPM Dual-frequency Precipitation Radar (DPR). From this, we find that IMERG and DPR are close at low rain rates, while, at high rain rates, IMERG tends to be lower than DPR. The second task is the assessment of IMERG’s ability to represent or detect structures commonly seen in tropical cyclones, including the annular structure and concentric eyewalls. For this, we operate on IMERG data with many machine learning algorithms and are able to achieve a 96% classification accuracy, indicating that IMERG does indeed contain TC structural information.

The non-scanning radiometer with short-wavelength (SW: 0.2–5.0 μm) and total-wavelength (TW: 0.2–50.0 μm) channels is the primary payload of the Integrated Earth–Moon Radiation Observation System (IEMROS), which is designed to provide comprehensive Earth radiation measurements and lunar calibrations at the L1 Lagrange point of the Earth–Moon system from a global perspective. This manuscript introduces a radiometer preflight calibration methodology, which involves background removal and is validated using accurate and traceable reference sources. Simulated Earth view tests are performed to evaluate repeatability, linearity, and gain coefficients over the operating range. Both channels demonstrate repeatability uncertainties better than 0.34%, indicating consistent and reliable measuring performance. Comparative polynomial regression analysis confirms significant linear response characteristics with two-channel nonlinearity less than 0.20%. Gain coefficients are efficiently determined using a two-point calibration approach. Uncertainty analysis reveals an absolute radiometric calibration accuracy of 0.97% for the SW channel and 0.92% for the TW channel, underscoring the non-scanning radiometer’s capability to provide dependable global Earth radiation budget data crucial to environmental and climate studies.

A Moon-based radiometer can provide continuous measurements for the Earth's full-disk broadband irradiance, which is useful for studying the Earth's Radiation Budget (ERB) at the height of the Top of the Atmosphere (TOA). The ERB describes how the Earth obtains solar energy and emits energy to space through the outgoing broadband Short-Wave (SW) and emitted thermal Long-Wave (LW) radiation. In this work, a model for estimating the Earth's outgoing radiative flux from the measurements of a Moon-based radiometer is established. Using the model, the full-disk LW and SW outgoing radiative flux are gained by converting the unfiltered entrance pupil irradiances (EPIs) with the help of the anisotropic characteristics of the radiances. Based on the radiative transfer equation, the unfiltered EPI time series is used to validate the established model. By comparing the simulations for a Moon-based radiometer with the satellite-based data from the National Institute of Standards and Technology Advanced Radiometer (NISTAR) and the Clouds and the Earth's Radiant Energy System (CERES) datasets, the simulations show that the daytime SW fluxes from the Moon-based measurements are expected to vary between 194 and 205 Wm−2; these simulations agree well with the CERES data. The simulations are about 5 to 20 Wm−2 smaller than the NISTAR data. For the simulated Moon-based LW fluxes, the range is 251~287 Wm−2. The Moon-based and NISTAR fluxes are consistently 5~15 Wm−2 greater than CERES LW fluxes, and both of them also show larger diurnal variations compared with the CERES fluxes. The correlation coefficients of SW fluxes for Moon-based data and NISTAR data are 0.97, 0.63, and 0.53 for the months of July, August, and September, respectively. Compared with the SW flux, the correlation of LW fluxes is more stable for the same period and the correlation coefficients are 0.87, 0.69, and 0.61 for July to September 2017. [ABSTRACT FROM AUTHOR]

Climate change is undeniably one of the most pressing and critical challenges facing humanity in the 21st century. In this context, monitoring the Earth’s Energy Imbalance (EEI) is fundamental in conjunction with greenhouse gases (GHGs) in order to comprehensively understand and address climate change. The French Uvsq-Sat NG pathfinder mission addresses this issue through the implementation of a Six-Unit CubeSat, which has dimensions of 111.3 × 36.6 × 38.8 cm in its unstowed configuration. Uvsq-Sat NG is a satellite mission spearheaded by the Laboratoire Atmosphères, Observations Spatiales (LATMOS), and supported by the International Satellite Program in Research and Education (INSPIRE). The launch of this mission is planned for 2025. One of the Uvsq-Sat NG objectives is to ensure the smooth continuity of the Earth Radiation Budget (ERB) initiated via the Uvsq-Sat and Inspire-Sat satellites. Uvsq-Sat NG seeks to achieve broadband ERB measurements using state-of-the-art yet straightforward technologies. Another goal of the Uvsq-Sat NG mission is to conduct precise and comprehensive monitoring of atmospheric gas concentrations (CO2 and CH4) on a global scale and to investigate its correlation with Earth’s Outgoing Longwave Radiation (OLR). Uvsq-Sat NG carries several payloads, including Earth Radiative Sensors (ERSs) for monitoring incoming solar radiation and outgoing terrestrial radiation. A Near-Infrared (NIR) Spectrometer is onboard to assess GHGs’ atmospheric concentrations through observations in the wavelength range of 1200 to 2000 nm. Uvsq-Sat NG also includes a high-definition camera (NanoCam) designed to capture images of the Earth in the visible range. The NanoCam will facilitate data post-processing acquired via the spectrometer by ensuring accurate geolocation of the observed scenes. It will also offer the capability of observing the Earth’s limb, thus providing the opportunity to roughly estimate the vertical temperature profile of the atmosphere. We present here the scientific objectives of the Uvsq-Sat NG mission, along with a comprehensive overview of the CubeSat platform’s concepts and payload properties as well as the mission’s current status. Furthermore, we also describe a method for the retrieval of atmospheric gas columns (CO2, CH4, O2, H2O) from the Uvsq-Sat NG NIR Spectrometer data. The retrieval is based on spectra simulated for a range of environmental conditions (surface pressure, surface reflectance, vertical temperature profile, mixing ratios of primary gases, water vapor, other trace gases, cloud and aerosol optical depth distributions) as well as spectrometer characteristics (Signal-to-Noise Ratio (SNR) and spectral resolution from 1 to 6 nm).

A Moon-based radiometer can provide continuous measurements for the Earth’s full-disk broadband irradiance, which is useful for studying the Earth’s Radiation Budget (ERB) at the height of the Top of the Atmosphere (TOA). The ERB describes how the Earth obtains solar energy and emits energy to space through the outgoing broadband Short-Wave (SW) and emitted thermal Long-Wave (LW) radiation. In this work, a model for estimating the Earth’s outgoing radiative flux from the measurements of a Moon-based radiometer is established. Using the model, the full-disk LW and SW outgoing radiative flux are gained by converting the unfiltered entrance pupil irradiances (EPIs) with the help of the anisotropic characteristics of the radiances. Based on the radiative transfer equation, the unfiltered EPI time series is used to validate the established model. By comparing the simulations for a Moon-based radiometer with the satellite-based data from the National Institute of Standards and Technology Advanced Radiometer (NISTAR) and the Clouds and the Earth’s Radiant Energy System (CERES) datasets, the simulations show that the daytime SW fluxes from the Moon-based measurements are expected to vary between 194 and 205 Wm−2; these simulations agree well with the CERES data. The simulations are about 5 to 20 Wm−2 smaller than the NISTAR data. For the simulated Moon-based LW fluxes, the range is 251~287 Wm−2. The Moon-based and NISTAR fluxes are consistently 5~15 Wm−2 greater than CERES LW fluxes, and both of them also show larger diurnal variations compared with the CERES fluxes. The correlation coefficients of SW fluxes for Moon-based data and NISTAR data are 0.97, 0.63, and 0.53 for the months of July, August, and September, respectively. Compared with the SW flux, the correlation of LW fluxes is more stable for the same period and the correlation coefficients are 0.87, 0.69, and 0.61 for July to September 2017.

Accurate information on tropical cyclone position, intensity, and structure is critical for storm surge prediction. Atmospheric reanalysis datasets can provide gridded, full coverage, long-term and multi-parameter atmospheric fields for the research on the impact of tropical cyclones on the upper ocean, which effectively makes up for the uneven temporal and spatial distribution of satellite remote sensing and in situ data. However, the reanalysis data cannot accurately describe characteristic parameters of tropical cyclones, especially in high wind conditions. In this paper, the performance of the tropical cyclone representation in ERA5 (European Centre for Medium-Range Weather Forecasts Reanalysis 5th Generation) is investigated and analyzed with respect to IBTrACS (International Best Track Archive for Climate Stewardship) during the period 2018–2020. Comparisons demonstrate that ERA5 winds significantly underestimate the maximum wind speed during the tropical cyclones (>30 m/s) compared to those provided by IBTrACS. An effective wind reconstruction method is examined to enhance tropical cyclone intensity representation in reanalysis data in 94 cases of 31 tropical cyclones 2018–2020. The reconstructed wind speeds are in good agreement with the SFMR (Stepped Frequency Microwave Radiometer) measured data and SMAP (Soil Moisture Active Passive) L-band radiometer remotely sensed measurements. The proposed wind reconstruction method can effectively improve the accuracy of the tropical cyclone representation in ERA5, and will benefit from the establishment of remote sensing satellite retrieval model and the forcing fields of the ocean model. [ABSTRACT FROM AUTHOR]

The Soil Moisture Active Passive (SMAP) mission includes a unique combination of instruments intended to provide daily global soil moisture data with high accuracy and resolution. Due to radar instrument failure, the default resolution of the data product decreased from the intended 9 km to 36 km shortly after the mission started to return data. To improve this, we employed the Scatterometer Image Reconstruction algorithm in its radiometer form (rSIR) to enhance the resolution of the radiometer brightness temperature measurements from which the soil moisture was derived. This paper compares the soil moisture estimates created from the rSIR-enhanced brightness temperatures with SMAP project radiometer L2_SM_SP and SMAP-Sentinel L2_SM_P products reported on 9 km and 3 km grids, respectively. We find that the difference of the rSIR-enhanced passive soil moisture product is generally within 0.020 cm 3 cm − 3 RMS of the 9 km SMAP radiometer L2_SM_SP and 0.045 cm 3 cm − 3 RMS of the 3 km SMAP-Sentinel L2_SM_P soil moisture products. The accuracy of the rSIR soil moisture can be improved by including better antenna pattern correction methods applied to the input TB measurements. [ABSTRACT FROM AUTHOR]

The Earth's radiation budget (ERB), measured at the top of the atmosphere (TOP), quantifies the radiation imbalance between the Earth–atmosphere system and space. The ERB's measurement accuracy depends on the observation system's design and calibration technology. Fitting regional scanning data from polar satellite payloads is the most common way to obtain the global radiation budget. Additionally, the radiometers are calibrated by onboard stable radiation sources. We propose a new ERB radiometer operating at the Lagrange L1 point of the Earth–Moon system, which has the characteristic of observing the Earth and Moon on a hemispheric spatial scale. Hence, earth-integrated radiation can be measured directly. Furthermore, the Moon is used as a natural source for on-orbit calibration, and the attenuation of the instrument is monitored and corrected through periodic observations. This paper presents the concept of the radiometer and focuses on the design and analysis of the radiometer's observation systems based on optical design and stray radiation suppression. The results show that the system has good imaging quality. The external stray radiation suppression reached an order of 10−8, and the thermal stray radiation can be eliminated by temperature control and compensation. The radiometer will provide long-term integrated ERB data. [ABSTRACT FROM AUTHOR]

Accurate information on tropical cyclone position, intensity, and structure is critical for storm surge prediction. Atmospheric reanalysis datasets can provide gridded, full coverage, long-term and multi-parameter atmospheric fields for the research on the impact of tropical cyclones on the upper ocean, which effectively makes up for the uneven temporal and spatial distribution of satellite remote sensing and in situ data. However, the reanalysis data cannot accurately describe characteristic parameters of tropical cyclones, especially in high wind conditions. In this paper, the performance of the tropical cyclone representation in ERA5 (European Centre for Medium-Range Weather Forecasts Reanalysis 5th Generation) is investigated and analyzed with respect to IBTrACS (International Best Track Archive for Climate Stewardship) during the period 2018–2020. Comparisons demonstrate that ERA5 winds significantly underestimate the maximum wind speed during the tropical cyclones (>30 m/s) compared to those provided by IBTrACS. An effective wind reconstruction method is examined to enhance tropical cyclone intensity representation in reanalysis data in 94 cases of 31 tropical cyclones 2018–2020. The reconstructed wind speeds are in good agreement with the SFMR (Stepped Frequency Microwave Radiometer) measured data and SMAP (Soil Moisture Active Passive) L-band radiometer remotely sensed measurements. The proposed wind reconstruction method can effectively improve the accuracy of the tropical cyclone representation in ERA5, and will benefit from the establishment of remote sensing satellite retrieval model and the forcing fields of the ocean model.

The Soil Moisture Active Passive (SMAP) mission includes a unique combination of instruments intended to provide daily global soil moisture data with high accuracy and resolution. Due to radar instrument failure, the default resolution of the data product decreased from the intended 9 km to 36 km shortly after the mission started to return data. To improve this, we employed the Scatterometer Image Reconstruction algorithm in its radiometer form (rSIR) to enhance the resolution of the radiometer brightness temperature measurements from which the soil moisture was derived. This paper compares the soil moisture estimates created from the rSIR-enhanced brightness temperatures with SMAP project radiometer L2_SM_SP and SMAP-Sentinel L2_SM_P products reported on 9 km and 3 km grids, respectively. We find that the difference of the rSIR-enhanced passive soil moisture product is generally within 0.020 cm3 cm−3 RMS of the 9 km SMAP radiometer L2_SM_SP and 0.045 cm3 cm−3 RMS of the 3 km SMAP-Sentinel L2_SM_P soil moisture products. The accuracy of the rSIR soil moisture can be improved by including better antenna pattern correction methods applied to the input TB measurements.

The Earth’s radiation budget (ERB), measured at the top of the atmosphere (TOP), quantifies the radiation imbalance between the Earth–atmosphere system and space. The ERB’s measurement accuracy depends on the observation system’s design and calibration technology. Fitting regional scanning data from polar satellite payloads is the most common way to obtain the global radiation budget. Additionally, the radiometers are calibrated by onboard stable radiation sources. We propose a new ERB radiometer operating at the Lagrange L1 point of the Earth–Moon system, which has the characteristic of observing the Earth and Moon on a hemispheric spatial scale. Hence, earth-integrated radiation can be measured directly. Furthermore, the Moon is used as a natural source for on-orbit calibration, and the attenuation of the instrument is monitored and corrected through periodic observations. This paper presents the concept of the radiometer and focuses on the design and analysis of the radiometer’s observation systems based on optical design and stray radiation suppression. The results show that the system has good imaging quality. The external stray radiation suppression reached an order of 10−8, and the thermal stray radiation can be eliminated by temperature control and compensation. The radiometer will provide long-term integrated ERB data.

The Global Precipitation Measurement (GPM) Dual-Frequency Precipitation Radar (DPR) (Ku- and Ka-band, or 14 and 35 GHz) provides the capability to resolve the precipitation structure under moderate to heavy precipitation conditions. In this manuscript, the use of near-coincident observations between GPM and the CloudSat Profiling Radar (CPR) (W-band, or 94 GHz) are demonstrated to extend the capability of representing light rain and cold-season precipitation from DPR and the GPM passive microwave constellation sensors. These unique triple-frequency data have opened up applications related to cold-season precipitation, ice microphysics, and light rainfall and surface emissivity effects.

This paper presents a built-in calibration procedure of a 10-to-20 GHz polarimeter aimed at measuring the I, Q, U Stokes parameters of cosmic microwave background (CMB) radiation. A full-band square waveguide double directional coupler, mounted in the antenna-feed system, is used to inject differently polarized reference waves. A brief description of the polarimetric microwave radiometer and the system calibration injector is also reported. A fully polarimetric calibration is also possible using the designed double directional coupler, although the presented calibration method in this paper is proposed to obtain three of the four Stokes parameters with the introduced microwave receiver, since V parameter is expected to be zero for the CMB radiation. Experimental results are presented for linearly polarized input waves in order to validate the built-in calibration system.

A low-mass and low-volume dual-polarization L-band radiometer is introduced that has applications for ground-based remote sensing or unmanned aerial vehicle (UAV)-based mapping. With prominent use aboard the ESA Soil Moisture and Ocean Salinity (SMOS) and NASA Soil Moisture Active Passive (SMAP) satellites, L-band radiometry can be used to retrieve environmental parameters, including soil moisture, sea surface salinity, snow liquid water content, snow density, vegetation optical depth, etc. The design and testing of the air-gapped patch array antenna is introduced and is shown to provide a 3-dB full power beamwidth of 37°. We present the radio-frequency (RF) front end design, which uses direct detection architecture and a square-law power detector. Calibration is performed using two internal references, including a matched resistive source (RS) at ambient temperature and an active cold source (ACS). The radio-frequency (RF) front end does not require temperature stabilization, due to characterization of the ACS noise temperature by sky measurements. The ACS characterization procedure is presented. The noise equivalent delta (Δ) temperature (NEΔT) of the radiometer is ~0.14 K at 1 s integration time. The total antenna temperature uncertainty ranges from 0.6 to 1.5 K.

Continuous estimates of the vertical integrated precipitable water vapor content from the tropospheric delay of the signal received by the antennas of the global positioning system (GPS) are used in this paper, in conjunction with the measurements of the Meteosat Second Generation (MSG) spinning enhanced visible and infrared imager (SEVIRI) radiometer and with the lightning activity, collected here by the ground-based lightning detection network (LINET), in order to identify links and recurrent patterns useful for improving nowcasting applications. The analysis of a couple of events is shown here as an example of more general behavior. Clear signs appear before the peak of lightning activity on a timescale from 2 to 3 h. In particular, the lightning activity is generally preceded by a period in which the difference between SEVIRI brightness temperature (TB) at channel 5 and channel 6 (i.e., ∆TB) presents quite constant values around 0 K. This trend is accompanied by an increase in precipitable water vapor (PWV) values, reaching a maximum in conjunction with the major flash activity. The results shown in this paper evidence good potentials of using radiometer and GPS measurements together for predicting the abrupt intensification of lightning activity in nowcasting systems.

Climate on Earth is determined by the Earth Radiation Budget (ERB), which quantifies the incoming and outgoing radiative energy fluxes. The ERB can be monitored by non-scanning wide field-of-view radiometers, or by scanning narrow field-of-view radiometers. We propose an enhanced design for the wide field-of-view radiometer, with as key features the use of a near-spherical cavity to obtain a uniform angular sensitivity and the integration of the shuttered electrical substitution principle, eliminating long term drifts of the radiometer and improving its time response. The target absolute accuracy is 1 W/m 2 and the target stability is 0.1 W/m 2 per decade for the measurement of the total outgoing Earth’s radiation. In order to increase the spatial resolution and to separate the total outgoing radiation into reflected Solar and emitted thermal radiation, we propose the joint use of the radiometer with wide field-of-view Shortwave (400−900 nm) and Longwave (8−14 μm) cameras. This paper presents the concept and design of the novel wide field-of-view radiometer, including simulations and analyses of its expected performance. We focus on mechanical design and the measurement characteristics based on optical and thermal analyses. In combination with the cameras, we obtain an estimated accuracy of 0.44 W/m 2 .

Land Surface Temperature (ST) represents the radiative temperature of the Earth’s surface and is used as input to hydrological, agricultural, and meteorological science applications. Due to the synoptic nature of satellite imaging systems, ST products derived from space-borne platforms are invaluable for estimating ST at the local, regional, and global scale. In the past two decades, an emphasis has been placed on the need to develop algorithms necessary to deliver accurate surface temperature products to support the needs of science users. However, corresponding efforts to validate these products are hindered by the availability of quality ground-based reference measurements. The NOAA Surface Radiation Budget (SURFRAD) network is commonly used to support ST validation efforts, but their instrumentation is broadband (4−50 μ m) and several of their sites lack spatial uniformity. To address the apparent deficiencies within existing validation networks, this work discusses a prototype radiometer that was developed to provide surface temperature estimates to support validation efforts for spaceborne thermal instruments. Specifically, a prototype radiometer was designed, built, and calibrated to acquire ground reference data to be used to validate ST product(s) derived from Landsat 8 image data. Lab-based efforts indicate that these prototype instruments are accurate to within 1.28 K and initial field measurements demonstrate agreement to Landsat-derived ST products to within 1.37 K.

Accurate prediction of sea surface emission is the key for sea surface salinity retrieval from satellite microwave radiometer. In order to retrieve salinity from satellite observation, several sea surface microwave emission models have been developed based on theoretical or empirical methods and validated by in-situ measurements in different regions. However, their performances are still unclear in the Chinese coastal waters. In this study, based on two cruises measurements in the East China Sea (ECS), including the brightness temperature measured by a shipborne microwave radiometer and other auxiliary data (sea surface salinity, sea surface temperature and wind speed), the performances of different sea surface emission models are tested. The results showed that the developed models provide fairly good accuracy in predicting brightness temperature; for example, the accuracy of small perturbance/small scale approximation model (SPM/SSA), two-scale model (TSM) and empirical model is in the range from 0.6 K to 3 K. Moreover, the TSM and empirical models are further improved by optimizing the model parameters in the ECS. Finally, the sea surface salinity were retrieved from shipborne measured data based on the improved models, and the results show that the root mean square (rms) differences between retrieved and in-situ sea surface salinity is about 0.4 psu, indicating the significant improvement by the regional model parameters.

Ground-based estimates of aboveground wet (fresh) biomass (AWB) are an important input for crop growth models. In this study, we developed empirical equations of AWB for rice, maize, cotton, and alfalfa, by combining several in situ non-spectral and spectral predictors. The non-spectral predictors included: crop height (H), fraction of absorbed photosynthetically active radiation (FAPAR), leaf area index (LAI), and fraction of vegetation cover (FVC). The spectral predictors included 196 hyperspectral narrowbands (HNBs) from 350 to 2500 nm. The models for rice, maize, cotton, and alfalfa included H and HNBs in the near infrared (NIR); H, FAPAR, and HNBs in the NIR; H and HNBs in the visible and NIR; and FVC and HNBs in the visible; respectively. In each case, the non-spectral predictors were the most important, while the HNBs explained additional and statistically significant predictors, but with lower variance. The final models selected for validation yielded an R2 of 0.84, 0.59, 0.91, and 0.86 for rice, maize, cotton, and alfalfa, which when compared to models using HNBs alone from a previous study using the same spectral data, explained an additional 12%, 29%, 14%, and 6% in AWB variance. These integrated models will be used in an up-coming study to extrapolate AWB over 60 × 60 m transects to evaluate spaceborne multispectral broad bands and hyperspectral narrowbands.

Accurate representation of the ocean-atmosphere coupling in weather, wave and climate models requires reliable estimates of air-sea surface fluxes of momentum, heat and mass. Whitecap fraction (W) usually quantifies the enhancement of the surface fluxes due to wave breaking. Satellite-based passive remote sensing of W from ocean surface brightness temperatures ( T B s) observes open ocean surface fluxes at low spatial resolution. Radiometric surface observations at higher resolution are necessary to monitor the complex environment in the coastal zone and in polar regions. We assess the feasibility of using the millimeter-wave frequencies (89 to 150 GHz) to observe whitecaps. We evaluate the derivative of the T B with respect to W as a measure for the observation of W. We describe the models and data used to evaluate the T B sensitivity to W for different instrumental and environmental conditions. Atmospheric absorption limits the ability to observe the surface at millimeter-wave frequencies. We find that the T B sensitivity to W at 89 GHz may be sufficient to support limited W retrieval from observations at altitudes below 1 km and that the T B sensitivity at 113 and 150 GHz is not sufficient. Clear skies, and low to moderate atmospheric humidity favor whitecap observations.

The High-resolution Infrared Radiation Sounder (HIRS) has been flown on 17 polar-orbiting satellites between the late 1970s and the present day. HIRS applications require accurate characterisation of uncertainties and inter-channel error correlations, which has so far been lacking. Here, we calculate error correlation matrices by accumulating count deviations for sequential sets of calibration measurements, and then correlating deviations between channels (for a fixed view) or views (for a fixed channel). The inter-channel error covariance is usually assumed to be diagonal, but we show that large error correlations, both positive and negative, exist between channels and between views close in time. We show that correlated error exists for all HIRS and that the degree of correlation varies markedly on both short and long timescales. Error correlations in excess of 0.5 are not unusual. Correlations between calibration observations taken sequentially in time arise from periodic error affecting both calibration and Earth counts. A Fourier spectral analysis shows that, for some HIRS instruments, this instrumental effect dominates at some or all spatial frequencies. These findings are significant for application of HIRS data in various applications, and related information will be made available as part of an upcoming Fundamental Climate Data Record covering all HIRS channels and satellites.

Near-surface remote sensing is an effective tool for in situ monitoring of canopy phenology, but the uncertainties involved in sensor-types and their deployments are rarely explored. We comprehensively compared three types of sensor (i.e., digital camera, spectroradiometer, and routine radiometer) at different inclination- and azimuth-angles in monitoring canopy phenology of a temperate deciduous forest in Northeast China for three years. The results showed that the greater contribution of understory advanced the middle of spring (MOS) for large inclination-angle of camera and spectroradiometer. The length of growing season estimated by camera from the east direction extended 11 d than that from the north direction in 2015 due to the spatial heterogeneity, but there was no significant difference in 2016 and 2018.The difference infield of view of sensors caused the MOS and the middle of fall, estimated by camera, to lag a week behind those by spectroradiometer and routine radiometer. Overall, the effect of azimuth-angle was greater than that of inclination-angle or sensor-type. Our assessments of the sensor types and their deployments are critical for the long-term accurate monitoring of phenology at the site scale and the regional/global-integration of canopy phenology data.

Lunar Flashlight (LF) is an innovative National Aeronautics and Space Administration (NASA) CubeSat mission that is dedicated to quantifying and mapping the water ice harbored in the permanently shadowed craters of the lunar South Pole. The primary goal is to understand the lunar resource potential for future human exploration of the Moon. To this end, the LF spacecraft will carry an active multi-band reflectometer, based on an optical receiver aligned with four high-power diode lasers emitting in the 1 to 2-μm shortwave infrared band, to measure the reflectance of the lunar surface from orbit near water ice absorption peaks. We present the detailed optical, mechanical, and thermal design of the receiver, which is required to fabricate this instrument within very demanding CubeSat resource allocations. The receiver has been optimized for solar stray light rejection from outside its field of view, and utilizes a 70 × 70-mm, aluminum, off-axis paraboloidal mirror with a focal length of 70 mm, which collects the reflected light from the Moon surface onto a single-pixel InGaAs detector with a 2-mm diameter, hence providing a 20-mrad field of view. The characterization of the flight receiver is also presented, and the results are in agreement with the expected performance obtained from simulations. Planned to be launched by NASA on the first Space Launch System (SLS) test flight, this highly mass-constrained and volume-constrained instrument payload will demonstrate several firsts, including being one of the first instruments onboard a CubeSat performing science measurements beyond low Earth orbit, and the first planetary mission to use multi-band active reflectometry from orbit.

An optimal payload selection conducted in the frame of the H2020 ONION project (id 687490) is presented based on the ability to cover the observation needs of the Copernicus system in the time period 2020–2030. Payload selection is constrained by the variables that can be measured, the power consumption, and weight of the instrument, and the required accuracy and spatial resolution (horizontal or vertical). It involved 20 measurements with observation gaps according to the user requirements that were detected in the top 10 use cases in the scope of Copernicus space infrastructure, 9 potential applied technologies, and 39 available commercial platforms. Additional Earth Observation (EO) infrastructures are proposed to reduce measurements gaps, based on a weighting system that assigned high relevance for measurements associated to Marine for Weather Forecast over Polar Regions. This study concludes with a rank and mapping of the potential technologies and the suitable commercial platforms to cover most of the requirements of the top ten use cases, analyzing the Marine for Weather Forecast, Sea Ice Monitoring, Fishing Pressure, and Agriculture and Forestry: Hydric stress as the priority use cases.

A rainfall retrieval algorithm for tropical cyclones (TCs) using 18.7 and 36.5 GHz of vertically and horizontally polarized brightness temperatures (Tbs) from the Microwave Radiation Imager (MWRI) is presented. The beamfilling effect is corrected based on ratios of the retrieved liquid water absorption and theoretical Mie absorption coefficients at 18.7 and 36.5 GHz. To assess the performance of this algorithm, MWRI measurements are matched with the National Snow and Ice Data Center (NSIDC) precipitation for six TCs. The comparison between MWRI and NSIDC rain rates is relatively encouraging, with a mean bias of −0.14 mm/h and an overall root-mean-square error (RMSE) of 1.99 mm/h. A comparison of pixel-to-pixel retrievals shows that MWRI retrievals are constrained to reasonable levels for most rain categories, with a minimum error of −1.1% in the 10⁻15 mm/h category; however, with maximum errors around −22% at the lowest (0⁻0.5 mm/h) and highest rain rates (25⁻30 mm/h). Additionally, Advanced Microwave Scanning Radiometer for Earth Observing System (AMSR-E) Tbs are applied to retrieve rain rates to assess the sensitivity of this algorithm, with a mean bias and RMSE of 0.90 mm/h and 3.11 mm/h, respectively. For the case study of TC Maon (2011), MWRI retrievals underestimate rain rates over 6 mm/h and overestimate rain rates below 6 mm/h compared with Precipitation Radar (PR) observations on storm scales. The Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI) rainfall data provided by the Remote Sensing Systems (RSS) are applied to assess the representation of mesoscale structures in intense TCs, and they show good consistency with MWRI retrievals.

The Radar Vegetation Index (RVI) is a well-established microwave metric of vegetation cover. The index utilizes measured linear scattering intensities from co- and cross-polarization and is normalized to ideally range from 0 to 1, increasing with vegetation cover. At long wavelengths (L-band) microwave scattering does not only contain information coming from vegetation scattering, but also from soil scattering (moisture & roughness) and therefore the standard formulation of RVI needs to be revised. Using global level SMAP L-band radar data, we illustrate that RVI runs up to 1.2, due to the pre-factor in the standard formulation not being adjusted to the scattering mechanisms at these low frequencies. Improvements on the RVI are subsequently proposed to obtain a normalized value range, to remove soil scattering influences as well as to mask out regions with dominant soil scattering at L-band (sparse or no vegetation cover). Two purely vegetation-based RVIs (called RVII and RVIII), are obtained by subtracting a forward modeled, attenuated soil scattering contribution from the measured backscattering intensities. Active and passive microwave information is used jointly to obtain the scattering contribution of the soil, using a physics-based multi-sensor approach; simulations from a particle model for polarimetric vegetation backscattering are utilized to calculate vegetation-based RVI-values without any soil scattering contribution. Results show that, due to the pre-factor in the standard formulation of RVI the index runs up to 1.2, atypical for an index normally ranging between zero and one. Correlation analysis between the improved radar vegetation indices (standard RVI and the indices with potential improvements RVII and RVIII) are used to evaluate the degree of independence of the indices from surface roughness and soil moisture contributions. The improved indices RVII and RVIII show reduced dependence on soil roughness and soil moisture. All RVI-indices examined indicate a coupled correlation to vegetation water content (plant moisture) as well as leaf area index (plant structure) and no single dependency, as often assumed. These results might improve the use of polarimetric radar signatures for mapping global vegetation.

This manuscript first revises the performance of total power, Dicke-type and noise-injection microwave radiometers. Equations for the radiometric resolution are revised or derived, and their performance in terms of the radiometric resolution improvement with respect to the ideal total power radiometer resolution is evaluated. It is then shown that the radiometric resolution of noise-injection radiometers can be optimized by adjusting dynamically the integration times devoted to the three measurements: antenna, antenna plus noise, and reference load. Numerical results are then presented to illustrate the dependence of the radiometric resolution with different instrument parameters. Experimental results are finally presented to corroborate the predicted performance. It is also shown that in many cases of interest these integration times can be set to a constant value with little degradation with respect to the optimum case, but better than the case in which the total integration time is divided in three equal subintervals.

While it has been proved that multiple scattering in the microwave frequencies has to be accounted for in precipitation retrieval algorithms, the effects of the random arrangements of drops in space has seldom been investigated. The fact is, a single rain drop size distribution (RDSD) corresponds with many actual 3D distributions of those rain drops and each of those may a priori absorb and scatter radiation in a different way. Each spatial configuration is equivalent to any other in terms of the RDSD function, but not in terms of radiometric characteristics, both near and far from field, because of changes in the relative phases among the particles. Here, using the T-matrix formalism, we investigate the radiometric variability of two ensembles of 50 different 3D, stochastically-derived configurations from two consecutive measured RDSDs with 30 and 31 drops, respectively. The results show that the random distribution of drops in space has a measurable but apparently small effect in the scattering calculations with the exception of the asymmetry factor.

UAV (unmanned Aerial Vehicle) platforms represent a challenging opportunity for the deployment of a number of remote sensors. These vehicles are a cost-effective option in front of manned aerial vehicles (planes and helicopters), are easy to deploy due to the short runways needed, and they allow users to meet the critical requirements of the spatial and temporal resolutions imposed by the instruments. L-band radiometers are an interesting option for obtaining soil moisture maps over local areas with relatively high spatial resolution for precision agriculture, coastal monitoring, estimation of the risk of fires, flood prevention, etc. This paper presents the design of a light-weight, airborne L-band radiometer for deployment in a small UAV, including the hardware and specific software developed for calibration, geo-referencing, and soil moisture retrieval. First results and soil moisture retrievals from different field experiments are presented.

Total power radiometer has a simple configuration and the best theoretical resolution. Gain fluctuations and calibration errors, however, can induce severe errors in the solved scene brightness temperature. To estimate the overall radiometer performance we present a numerical simulation tool that can be used to determine the radiometric resolution. Our model considers three main components that degrade the radiometric resolution: thermal noise, 1/f noise and calibration errors. These error sources have long been known to exist, but comprehensive models able to account all these effects quantitatively and accurately in a practical manner have been missing. We have developed a radiometer simulation model that is able to produce radiometer signals that incorporate realistic radiometer effects that show up as noise and other errors in the radiometer video signal. Our simulation tool integrates the fundamental radiometer theories numerically and allows the investigation of different calibration schemes and receiver topologies. The model can be used as a guide for design and optimization as well as for verification of the radiometer performance. Moreover, it can be extended to a much larger and more complex radiometer systems allowing better system level performance estimation and optimization with minimal bread-board implementations. The model mimics real radiometer video data and thus the complete data analysis pipeline can be developed and verified before the real video data is available. In this paper, the model has been applied to a total power radiometer operating in the 52 GHz frequency range. [ABSTRACT FROM AUTHOR]

Ground-based estimates of aboveground wet (fresh) biomass (AWB) are an important input for crop growth models. In this study, we developed empirical equations of AWB for rice, maize, cotton, and alfalfa, by combining several in situ non-spectral and spectral predictors. The non-spectral predictors included: crop height (H), fraction of absorbed photosynthetically active radiation (FAPAR), leaf area index (LAI), and fraction of vegetation cover (FVC). The spectral predictors included 196 hyperspectral narrowbands (HNBs) from 350 to 2500 nm. The models for rice, maize, cotton, and alfalfa included H and HNBs in the near infrared (NIR); H, FAPAR, and HNBs in the NIR; H and HNBs in the visible and NIR; and FVC and HNBs in the visible; respectively. In each case, the non-spectral predictors were the most important, while the HNBs explained additional and statistically significant predictors, but with lower variance. The final models selected for validation yielded an R2 of 0.84, 0.59, 0.91, and 0.86 for rice, maize, cotton, and alfalfa, which when compared to models using HNBs alone from a previous study using the same spectral data, explained an additional 12%, 29%, 14%, and 6% in AWB variance. These integrated models will be used in an up-coming study to extrapolate AWB over 60 × 60 m transects to evaluate spaceborne multispectral broad bands and hyperspectral narrowbands. [ABSTRACT FROM AUTHOR]