Search

Understanding the characteristics of the raindrop size distribution (DSD) is crucial to improve our knowledge of the microphysical processes of precipitation and to improve the accuracy of radar quantitative precipitation estimation (QPE). In this study, the spatial variability of DSD in different regions of Beijing and its influence on radar QPE are analyzed using 11 disdrometers. The DSD data are categorized into three regions: Urban, suburban, and mountainous according to their locations. The DSD exhibits evidently different characteristics in the urban, suburban, and mountain regions of Beijing. The average raindrop diameter is smaller in the urban region compared to the suburban region. The average rain rate and raindrop number concentration are lower in the mountainous region compared to both urban and suburban regions. The difference in DSD between urban and suburban regions is due to the difference in DSD for the same precipitation types, while the difference in DSD between mountain and plains (i.e., urban and suburban regions) is the combined effect of the convection/stratiform ratio and the difference of DSD for the same precipitation types. Three DSD-based polarimetric radar QPE estimators were retrieved and estimated. Among these three QPE estimators, R(ZH), R(Kdp), and R(Kdp, ZDR), R(Kdp, ZDR) performs best, followed by R(Kdp), and R(ZH) performs worst. R(Kdp) is more sensitive to the representative parameters, while R(ZH) and R(Kdp, ZDR) are more sensitive to observational error and systematic bias (i.e., calibration). [ABSTRACT FROM AUTHOR]

Severe hailstorms frequently occurred in Beijing between May and August 2021, leading to extensive hail damage. These hailstorms were observed by radar and satellite data, and reported by surface observers. In this study, the spectral and cloud microphysical characteristics of typical Beijing events in 2021 were analyzed using Himawari-8 satellite products and ground-based S-band weather radar data obtained from the Beijing Meteorological Bureau. The relationship between Himawari-8 brightness temperature differences (BTD) and radar reflectivity was also investigated. The results revealed that the significant spectral depression of brightness temperatures (BTs) in hail clouds was observed by a satellite. Furthermore, the stronger the radar reflectivity was, the more rapidly BTD decreased, with a nonlinear relationship between them. The results of cloud physical characteristics show that, for cloud-top heights above 10 km, the cloud effective radius was about 25 μm, with a cloud-top temperature of 225 K during these hail events. By means of Gaussian fitting, the BT threshold value (11.2 μm) was determined by satellite at 230 K, with a BTD focused on 1.9 K when hailstorms occurred. These results will help us better understand the characteristics of hailstorms, while also providing information for future hail suppression in Beijing. [ABSTRACT FROM AUTHOR]

The performance of general circulation models (GCMs) in simulating horizontal winds is important because the distribution and variation in horizontal winds are central to investigating atmospheric dynamic characteristics and processes. Also, horizontal wind data can be used to extract some of the required information on gravity waves, tides, and planetary waves. In this context, the present paper evaluates the capability of the Institute of Atmospheric Physics atmospheric general circulation model high-top version (IAP-HAGCM) in simulating the horizontal winds and tides of the troposphere and lower stratosphere by presenting a climatological and statistical comparison against observations of the powerful Beijing mesosphere–stratosphere–troposphere (MST) radar (39.78°N, 116.95°E) during 2012–2014. The results illustrated that the IAP-HAGCM can successfully reproduce the time–altitude distribution of the monthly mean zonal wind and diurnal tide amplitude, albeit with some underestimation. The mean correlation coefficients and root-mean-square error for the zonal (meridional) winds were 0.94 (0.73) and 6.60 m s−1 (2.90 m s–1), respectively. Additionally, the IAP-HAGCM can capture the temporal variation in both the zonal and meridional winds. It is worth noting that, compared with the seven coupled model intercomparison project phase 6 (CMIP6) models, the IAP-HAGCM performs better in meridional wind simulations below 15 km. However, there are discrepancies in altitudinal ranges with large wind velocities, such as the westerly jet, in the transition region of the troposphere and stratosphere, and in February, April, July, and September. It is suggested that model users should take advantage of the model's simulation ability by combining this information regarding when and where it is optimal with their own research purposes. Moreover, the evaluation results in this paper can also serve as a reference for guiding improvements of the IAP-HAGCM. [ABSTRACT FROM AUTHOR]

We studied the characteristics of quasi-two-day wave (QTDW) using the meridional wind in the mesosphere and lower thermosphere (MLT) obtained from a meteor radar over Kototabang (KB, 0.2 ° S, 100.3 ° E) from 2003 to 2012. Atmospheric oscillations have a crucial impact on atmospheric dynamics, which contributes to more accurate space weather forecasting, thus providing a more secure space environment for human space exploration activities such as remote sensing and satellite navigation. QTDWs are typical atmospheric oscillations in the upper stratosphere, mesosphere and lower thermosphere. The occurrence time, amplitudes, periods and vertical wavelengths of QTDW events are analyzed statistically. Data obtained from the TIMED Doppler Interferometer (TIDI), which can measure wind and temperature and is onboard the Thermosphere, Ionosphere, Mesosphere Energetics and Dynamics (TIMED) satellite, are used to analyze the global distribution and spatial structure of QTDWs with different zonal wavenumbers. The characteristics of the QTDWs over KB are compared with the QTDWs at the middle latitudes using the meridional wind data from a meteor radar over Wuhan (114.4 ° E, 30.6 ° N), Beijing (116.5 ° E, 39.9 ° N) and Mohe (121.1 ° E, 50.1 ° N). The amplitudes of the QTDW and spectral analysis are calculated by the least squares fitting method. Our results demonstrate that QTDWs are present almost all year around over KB. The occurrence time, amplitudes, periods and vertical wavelengths of QTDW events with different zonal wavenumbers are determined in this study. We also find that the statistical characteristics of the QTDWs in KB are different from those at middle latitudes. The westward zonal wavenumber −4 (W4) events gradually increase with increasing latitude, whereas westward zonal wavenumbers −1, −2, and −3 (W1, W2 and W3, respectively) events all decrease with increasing latitude. [ABSTRACT FROM AUTHOR]

It is commonly believed that clear-air echoes detected by weather radars are caused by atmobios migration. However, clear-air echoes are sometimes inconsistently related to the activity of living creatures. In some cases, the characteristics of radar products seem to conform to biological scattering, but the movement of echoes cannot be observed. For these reasons, we sought to expand the cause of clear-air echoes from a Chinese Doppler S-band Weather Radar (CINRAD/SA) in Beijing. Some contradictions were discovered in a case which diverged from previous conclusions. It was found that the progression and movement of clear-air echoes do not conform to the rules of biological activities. The frequency distribution of dual-wavelength ratio peaks is 21.5 dB, which is in accordance with Villars–Weisskopf's turbulence theory. From 1 May to 20 May, the 58% dual-wavelength ratio between the S-band and the X-band was distributed between 18 dB and 24 dB. These results show that more than half of the clear-air echoes of CINRAD/SA at night were caused by turbulence in Beijing. A new model of troposcatter propagation, the reflecting-layers model, was then introduced to explain the radar observations. According to the reflecting-layers model, the echoes' diurnal variation and reflectivity characteristics are attributed to the effects of turbulent mixing. Excessive turbulent mixing affects the generation of the reflective layer, thereby weakening the echo signal. It is necessary to re-examine the position of turbulence in clear-air echoes. [ABSTRACT FROM AUTHOR]

InSAR (Interferometric Synthetic Aperture Radar) is widely recognized as a crucial remote sensing tool for monitoring various geological disasters because it provides all-day and all-weather monitoring. Nevertheless, the current interpretation methods for InSAR heavily depend on the interpreter's experience, which hinders efficiency and fails to meet the requirements for the timely detection of geologic hazards. Furthermore, the results obtained through current InSAR processing carry inherent noise interference, further complicating the interpretation process. To address those issues, this paper proposes an approach that enables automatic and rapid identification of deformation zones. The proposed method leverages IPTA (Interferometric Point Target Analysis) technology for SAR data processing. It combines the power of HNSW (Hierarchical Navigable Small Word) and DBSCAN (Density-Based Spatial Clustering of Applications with Noise) algorithms to cluster deformation results. Compared with traditional methods, the computational efficiency of the proposed method is improved by 11.26 times, and spatial noise is suppressed. Additionally, the clustering results are fused with slope units determined using DEM (Digital Elevation Model), which facilitates the automatic identification of slopes experiencing deformation. The experimental verification in the western mountainous area of Beijing has identified 716 hidden danger areas, and this method is superior to the traditional technology in speed and automation. [ABSTRACT FROM AUTHOR]

Accurately estimating building heights is crucial for various applications, including urban planning, climate studies, population estimation, and environmental assessment. However, this remains a challenging task, particularly for large areas. Satellite-based Light Detection and Ranging (LiDAR) has shown promise, but it often faces difficulties in distinguishing building photons from other ground objects. To address this challenge, we propose a novel method that incorporates building footprints, relative positions of building and ground photons, and a self-adaptive buffer for building photon selection. We employ the Ice, Cloud, and Land Elevation Satellite 2 (ICESat-2) photon-counting LiDAR, specifically the ICESat-2/ATL03 data, along with building footprints obtained from the New York City (NYC) Open Data platform. The proposed approach was applied to estimate the heights of 17,399 buildings in NYC, and the results showed strong consistency with the reference building heights. The root mean square error (RMSE) was 8.1 m, and for 71% of the buildings, the mean absolute error (MAE) was less than 3 m. Furthermore, we conducted an extensive evaluation of the proposed approach and thoroughly investigated the influence of terrain, region, building height, building density, and parameter selection. We also verified the effectiveness of our approach in an experimental area in Beijing and compared it with other existing methods. By leveraging ICESat-2 LiDAR data, building footprints, and advanced selection techniques, the proposed approach demonstrates the potential to accurately estimate building heights over broad areas. [ABSTRACT FROM AUTHOR]

Revealing the land subsidence in Beijing, China, induced by the massive groundwater extraction in the past three decades, is important to mitigate the hazards and protect the residences and infrastructure. Many SAR (Synthetic Aperture Radar) datasets have been successfully applied to reveal the land subsidence over Beijing in previous research, while few works were achieved on land subsidence revealed by time-series InSAR (Interferometric Synthetic Aperture Radar) with Gaofen-3 SAR images. In this study, we successfully perform the time-series InSAR analysis with Gaofen-3 SAR images to extract the land subsidence in Beijing from 2020 to 2021. The Sentinel-1 SAR images were used to assess the accuracy of Gaofen-3 images. The subsidence scale and extent are consistent in detected major subsidence bowls between the two datasets. The spatial–temporal evolution and the deceleration of Beijing land subsidence were revealed by comparing with the Sentinel-1 results from 2017 to 2020. Moreover, we evaluated the interferometric performance of Gaofen-3 satellite SAR imagery and analyzed the main factors that mostly influence the coherence and quality of interferograms. Our results proved that the long perpendicular baselines decrease the coherence seriously over the study area, and the artifacts induced by inaccurate orbit information reduce the quality of the Gaofen-3 interferograms. Refining and removing the two main artifacts could improve the quality of interferograms formed by Gaofen-3 SAR images. [ABSTRACT FROM AUTHOR]

Accurate, rapid, and automatic local climate zone (LCZ) mapping is essential for urban climatology and studies in terms of urban heat islands. Remotely sensed imageries incorporated with machine learning algorithms are widely utilized in LCZ labeling. Nevertheless, large-scale LCZ mapping is still challenging due to the complex vertical structure of underlying urban surfaces. This study proposed a new method of LCZ labeling that uses a random forest classifier and multi-source remotely sensed data, including Sentinel 1A Synthetic Aperture Radar (SAR), Sentinel 2 Multispectral Instrument, and Luojia1-01 night-time light data. In particular, leaf-on and -off imageries and surface thermal dynamics were utilized to enhance LCZ labeling. Additionally, we systematically evaluated how daytime and night-time features influence the performance of the classification procedure. Upon examination, the results for Beijing, China, were confirmed to be robust and refined; the Overall Accuracy (OA) value of the proposed method was 88.86%. The accuracy of LCZs 1–9 was considerably increased when using the land surface temperature feature. Among these, the Producer Accuracy (PA) value of LCZ 3 (compact low-rise) significantly increased by 16.10%. Notably, it was found that NTL largely contributed to the classification concerning LCZ 3 (compact low-rise) and LCZ A/B (dense trees). The performance of integrating leaf-on and -off imageries for LCZ labeling was better than merely uses of leaf-on or -off imageries (the OA value increased by 4.75% compared with the single use of leaf-on imagery and by 3.62% with that of leaf-off imagery). Future studies that use social media big data and Very-High-Resolution imageries are required for LCZ mapping. This study shows that combining multispectral, SAR, and night-time light data can improve the performance of the random forest classifier in general, as these data sources capture significant information about surface roughness, surface thermal feature, and night-time features. Moreover, it is found that incorporating both leaf-on and leaf-off remotely sensed imageries can improve LCZ mapping. [ABSTRACT FROM AUTHOR]

Surface subsidence is a serious threat to human life, buildings and traffic in Beijing. Surface subsidence is closely related to human activities, and human activities in Beijing area showed a decreasing trend during the Corona Virus Disease 2019 (COVID-19). To study surface subsidence in Beijing before and after the COVID-19 outbreak and its causes, a total of 51 Sentinel-1A SAR images covering Beijing from January 2018 to April 2022 were selected to derive subsidence information by Time Series Interferometry Synthetic Aperture Radar (TS-InSAR). The results of surface subsidence in Beijing demonstrate that Changping, Chaoyang, Tongzhou and Daxing Districts exhibited the most serious subsidence phenomenon before the COVID-19 outbreak. The four main subsidence areas form an anti-Beijing Bay that surrounds other important urban areas. The maximum subsidence rate reached −57.0 mm/year. After the COVID-19 outbreak, the main subsidence area was separated into three giant subsidence funnels and several small subsidence funnels. During this period, the maximum subsidence rate was reduced to −43.0 mm/year. Human activity decrease with the COVID-19 outbreak. This study effectively analysed the influence of natural factors on surface subsidence after excluding most of the human factors. The following conclusions are obtained from the analysis: (1) Groundwater level changes, Beijing's geological structure and infrastructure construction are the main reasons for surface subsidence in Beijing. (2) Seasonal changes in rainfall and temperature indirectly affect groundwater level changes, thereby affecting surface subsidence in the area. (3) The COVID-19 outbreak in early 2020 reduced the payload of Beijing's transportation facilities. It also slowed down the progress of various infrastructure construction projects in Beijing. These scenarios affected the pressure on the soft land base in Beijing and reduced the surface subsidence trend to some extent. [ABSTRACT FROM AUTHOR]

Geological hazards often occur in mountainous areas and are sudden and hidden, so it is important to identify and assess geological hazards. In this paper, the western mountainous area of Beijing was selected as the study area. We conducted research on landslides, collapses, and unstable slopes in the study area. The surface deformation of the study area was monitored by multi-temporal interferometric synthetic aperture radar (MT-InSAR), using a combination of multi-looking point selection and permanent scatterer (PS) point selection methods. Random forest (RF), support vector machine (SVM), convolutional neural network (CNN), and recurrent neural network (RNN) models were selected for the assessment of geological hazard susceptibility. Sixteen geological hazard-influencing factors were collected, and their information values were calculated using their features. Multicollinearity analysis with the relief-F method was used to calculate the correlation and importance of the factors for factor selection. The results show that the deformation rate along the line-of-sight (LOS) direction is between −44 mm/year and 28 mm/year. A total of 60 geological hazards were identified by combining surface deformation with optical imagery and other data, including 7 collapses, 25 unstable slopes, and 28 landslides. Forty-eight of the identified geological hazards are not recorded in the Beijing geological hazards list. The most effective model in the study area was RF. The percentage of geological hazard susceptibility zoning in the study area is as follows: very low susceptibility 27.40%, low susceptibility 28.06%, moderate susceptibility 21.19%, high susceptibility 13.80%, very high susceptibility 9.57%. [ABSTRACT FROM AUTHOR]

Rapid simulation of land subsidence can provide an effective means of facilitating its management and control. This paper innovatively introduced a back-propagation (BP) neural network subsidence simulation model which was optimized by the sparrow search algorithm (SSA), hereinafter referred to as the SSA-BP model, to simulate land subsidence in Tongzhou District, Beijing. First, based on the time series interferometric synthetic aperture radar (InSAR) monitoring, different technologies such as spatial analysis, Google Earth Engine (GEE), and machine learning were utilized together with a variety of multi-source spatial data, including groundwater level, compressible layer thickness, Visible Infrared Imager Radiometer Suite (VIIRS) nighttime light images, and the OpenStreetMap (OSM) road distribution. Furthermore, we determined the optimal grid scale for land subsidence research and worked out a multifactor-driven SSA-BP land subsidence simulation model for which sensitivity analysis was performed with great care. Main conclusions: (1) From November 2010 to January 2020, the average annual surface displacement rate in Beijing's subcentre, Tongzhou, ranged from −133.9 to +3.9 mm/year. (2) Our SSA-BP land subsidence simulation model allows for a relatively high overall accuracy. The average root mean square error (RMSE) is 5.00 mm/year, the average mean absolute error (MAE) is 3.80 mm/year, and the average coefficient of determination (R2) is 0.83. (3) Sensitivity analysis shows that the SSA-BP model driven by multiple factors has a far better simulation performance than the model driven by any single weighting factor, and displays the highest sensitivity to the groundwater level factor among all the weighting factors. In terms of subdividing the study area, our SSA-BP land subsidence model runs with multifunctional zones displayed a higher accuracy than that without. This paper made use of a machine learning model to simulate land subsidence in Beijing's Tongzhou District and explored the sensitivity of different factors to land subsidence, which is helpful for its scientific prevention. [ABSTRACT FROM AUTHOR]

Based on three years of data observed by Beijing MST radar between 2012 and 2014, this study gives the distribution characteristics of the turbulence energy dissipation rate ε and the vertical turbulence diffusion coefficient K z in the troposphere–lower stratosphere over Beijing based on the spectral width method. Additionally, from the perspective of atmospheric stability expressed by the Brunt–Väisälä frequency N and the gradient Richardson number Ri, the seasonal variations of turbulence parameters at different heights are analyzed. The results show that ε ( K z ) is distributed in the range of 10−4 to 10−1.5 m2 s−3 (100 to 101 m2 s−1), with median values of 10−3 to 10−2.5 m2 s−3 (100.4 to 100.75 m2 s−1). In the height range of −1 km to about +1 km from the tropopause, the profiles of ε have no noticeable seasonal difference from October to next May, and ε increases sharply with the slope of linear regression ∇log(ε)/∇h = 0.25 (m2 s−3) km−1. The seasonal variation of turbulence parameters has noticeable differences at different atmospheric layers. Furthermore, the atmospheric static/dynamic stability and turbulence intensity are the influencing factors of turbulence parameters. From the tropopause to 14 km, the values of ε and N both have a peak from October to next May, and this peak layer disappears from July to August. Within the range of 2–4 km from the ground, K z and the frequency of Ri < 0.25 have a significant positive correlation, with a Pearson correlation coefficient greater than 0.5, and both have large value layers in March to May and September to October. The turbulence intensity above 15 km is likely the main factor affecting the turbulence dissipation rate and vertical turbulence diffusion coefficient. [ABSTRACT FROM AUTHOR]

Groundwater overexploitation is a critical issue in the North China Plain (NCP), resulting in groundwater level decline and surface subsidence for the last half-century. This problem, however, has been greatly alleviated by the South-to-North Water Diversion (SNWD) Project since 2015. Monitoring of this process has been steadily improved in recent years using water level and geodetic observations. Here, we characterize the water storage change at the Huairou groundwater reserve site (HGRS) in Beijing due to the SNWD by combining Interferometric Synthetic Aperture Radar (InSAR) data of the Sentinel-1 satellites, continuous Global Positioning System (GPS) data, and well water level data observed during the same time. InSAR observations revealed subsidence up to ~400 mm in the Beijing plain but uplift at ~40 mm in the HGRS during 2015–2019, and more than 70% of the uplift occurred from October 2018 to January 2019. By integrating the most significant uplift deformation during October 2018 to January 2019 with water level observations at the same time, we estimated the storativity of the confined aquifer system at HGRS as 1. 68 – 7. 82 × 10 − 3 , weighing in the correction for effective stress and surface deformation for various situations. Based on the estimated aquifer storativity and the observed water level change in the unconfined and confined aquifer, the recharged water storage for the confined and unconfined aquifers was estimated as 1. 20 – 1. 39 × 10 7   m 3 and ~ 2. 86 × 10 8   m 3 from 6 October 2018 to 22 January 2019, respectively, which is about 4% and 91% of the surface water recharge through river channels in the same period due to the SNWD Project. Our study demonstrates that integration of geodetic and hydrological data can provide crucial information for the assessment of groundwater circulation and assistance of groundwater management. [ABSTRACT FROM AUTHOR]

Beijing is a major city suffering from land subsidence due to long-term over-exploitation of groundwater. The South-to-North Water Diversion Project (SNWDP), however, has had a significant impact on the structure of water consumption since the end of 2014, and it is changing the status of land subsidence in Beijing. In this study, we employed Persistent Scatterers Synthetic Aperture Radar Interferometric (PS-InSAR) to investigate the decadal evolution of land subsidence in Beijing with 100 TerraSAR-X stripmap images collected from April 2010 to December 2019. The water resources, historic climate and urban construction data were compiled for the years of 2010 to 2019 to analyze changes in groundwater level, human activity, surface geology, active faults and land subsidence patterns. The results show that the changes in the water supply structure are correlated to a rise in groundwater level after 2015. These changes include an increase in the water supply from the SNWDP, a reduction in groundwater exploitation, the optimization of water consumption, replacing recycled water for environmental water and a reduction in the use of water for agriculture. Land subsidence in the study area was concentrated in the eastern regions, trending towards a decreasing velocity starting about two years after the commencement of SNWDP in 2015. Uneven subsidence in the land subsidence area was related to excavations of underground soil, and the construction of Line 6 and Line 7 led to rapid nonlinear subsidence. Our results have scientific significance for reducing subsidence hazards in the context of SNWDP and urban expansion. [ABSTRACT FROM AUTHOR]

Since the 1930s, due to the rapid development of the city and the increase of population, the demand from Beijing residents for water resources has gradually increased. Land deformation in the Beijing Plain is a serious issue. In order to warn of, and mitigate, disasters, it is urgently necessary to obtain the latest rate, extent, and temporal evolution of land subsidence in Beijing. Firstly, the temporal and spatial distribution characteristics of land deformation in Beijing during 2003–2020 were unveiled using the time-series interferometric synthetic aperture radar (InSAR) technique and two different satellite datasets, sentinel-1a/1b and ENVISAT ASAR. By means of combining calibration of InSAR results with the global positioning system (GPS), we studied the evolutionary process of long-term land subsidence in Beijing. The precision of our InSAR annual subsidence results is less than 10 mm. Land subsidence in Beijing is unevenly distributed, and so five main land subsidence zones were monitored. The time-series results showed that the rate of land subsidence rate continued to increase from 2003 to 2015, but has gradually shown a slowing trend from 2015 to 2020. Further, we used the quadratic polynomial fitting method to interpolate the time-series deformation results from 2010 to 2015, and compared these with GPS. The results demonstrated that although the InSAR observation method is not strictly registered with GPS in time, its deformation trend is consistent. In addition, the calibrated long time-series was consistent with the three deformation stages of land subsidence evolution in Beijing. Finally, we analyzed the deformation information obtained by InSAR technology in combination with land use type data, precipitation and groundwater data. The results demonstrated that the central area is mostly stable, and land deformation in the northeast is obvious and uneven. In addition, land use type and precipitation have little influence on land subsidence. Changes in land subsidence were closely related to changes in groundwater level, and seasonal variations in deformation correlated with precipitation. [ABSTRACT FROM AUTHOR]

Based on long-term lidar (light detection and ranging) observations at Yanqing (40.5°N, 116°E) and Pingquan (41°N, 118.7°E), cloud events occurred in the vicinity of the stratopause above Beijing were reported for the first time. These events occurred with tenuous and sparse layers within the altitude range of 33–65 km, and the maximum VBSC value ranged from 1 × 10 − 10 m − 1 sr − 1 to 5.5 × 10 − 9 m − 1 sr − 1 . Considering temperature and water vapor measurements from SABER/TIMED, the occurrence mechanism of these lidar-observed cloud events was examined. It was found that some cloud layers resulted from the nucleation of water vapor due to the local meteorological changes in the middle atmosphere, while other lidar-observed clouds could comprise floating clusters of cosmic dust, hydrate droplets, volcanic ash, space traffic exhaust, etc. These cloud events are rare cloud-like phenomena in the middle atmosphere observed by lidars at midlatitudes in China; they differ from NLCs and PSCs in terms of altitude distribution and seasonal variation, and the relevant microphysics processes behind their occurrence are likely meaningful to meteorology at midlatitudes. [ABSTRACT FROM AUTHOR]

Clustering of multi-source geospatial big data provides opportunities to comprehensively describe urban structures. Most existing studies focus only on the clustering of a single type of geospatial big data, which leads to biased results. Although multi-view subspace clustering methods are advantageous for fusing multi-source geospatial big data, exploiting a robust shared subspace in high-dimensional, non-uniform, and noisy geospatial big data remains a challenge. Therefore, we developed a method with adaptive graphs to constrain multi-view subspace clustering of multi-source geospatial big data (agc2msc). First, for each type of data, high-dimensional and noisy original features were projected into a low-dimensional latent representation using autoencoder networks. Then, adaptive graph constraints were used to fuse the latent representations of multi-source data into a shared subspace representation, which preserved the neighboring relationships of data points. Finally, the shared subspace representation was used to obtain the clustering results by employing a spectral clustering algorithm. Experiments on four benchmark datasets showed that agc2msc outperformed nine state-of-the-art methods. agc2msc was applied to infer urban land use types in Beijing using the taxi GPS trajectory, bus smart card transaction, and points of interest datasets. The clustering results may provide useful calibration and reference for urban planning. [ABSTRACT FROM AUTHOR]

The long-term over-exploitation of groundwater has not only caused the compaction of aquifer thickness and surface deformation but has also further aggravated the loss of groundwater storage (GWS) in Beijing plain. The South-to-North Water Diversion Project (SNWDP) furnishes a new source of water for Beijing. By reviewing related studies, it was found that there are few studies on the realization of GWS estimation based on InSAR technology considering the lag effect. Therefore, in this study, firstly, the long-time series deformation characteristics of Beijing plain were obtained from 46 RadarSat-2 images using small baseline subset interferometric synthetic aperture radar (SBAS-InSAR) technology. Secondly, the seasonal components of surface deformation and hydraulic head change were extracted by means of multichannel singular spectrum analysis (MSSA), verifying the separation accuracy by means of Monto Carlo-SSA (MC-SSA). Finally, for the hydrodynamic delay (aquifer water supply/drainage) of the complex aquifer system, we introduced the time lag cross-correlation (TLCC) approach to correct the hysteresis response of seasonal deformation relative to the variation of the aquifer system head, so as to realize the estimation of aquifer storage properties and GWS loss, even unrecoverable GWS (UGWS). The results showed that the average annual variation of total GWS (TGWS) in Beijing plain was −6.702 × 107 m3, of which the depletion volume of UGWS was −6.168 × 107 m3, accounting for 92.03% of the TGWS. On a temporal scale, the depletion of UGWS lagged behind the total head change, with about one year of lag time. On a spatial scale, in contrast to the north of Beijing plain, the depletion of UGWS in the south only recovered briefly after 2015 and then continued to decline. This further indicated that the process of the decline of middle-deep confined head and long-term GWS loss caused by over-exploitation of groundwater was irreversible. These findings are of great significance to optimize the allocation of groundwater resources, reduce the harm of land subsidence and protect groundwater resources. [ABSTRACT FROM AUTHOR]

Beijing's One Million Mu Plain Afforestation Project involves planting large areas with the exotic North American tree species Fraxinus pennsylvanica Marsh (ash). As an exotic tree species, ash is very vulnerable to infestations by the emerald ash borer (EAB), a native Chinese wood borer pest. In the early stage of an EAB infestation, attacked trees show no obvious sign. Once the stand has reached the late damage stage, death occurs rapidly. Therefore, there is a need for efficient early detection methods of EAB stress over large areas. The combination of unmanned aerial vehicle (UAV)-based hyperspectral imaging (HI) with light detection and ranging (LiDAR) is a promising practical approach for monitoring insect disturbance. In this study, we identified the most useful narrow-band spectral HI data and 3D LiDAR data for the early detection of EAB stress in ash. UAV-HI data of different infested stages (healthy, light, moderate and severe) of EAB in the 400–1000 nm range were collected from ash canopies and were processed by Partial Least Squares–Variable Importance in Projection (PLS-VIP) to identify the maximally sensitive bands. Band R678 nm had the highest PLS-VIP scores and the most robust classification ability. We combined this band with band R776 nm to develop an innovative normalized difference vegetation index (NDVI(776,678)) to estimate EAB stress. LiDAR data were used to segment individual trees and supplement the HI data. The new NDVI(776,678) identified different stages of EAB stress, with a producer's accuracy of 90% for healthy trees, 76.25% for light infestation, 58.33% for moderate infestation, and 100% for severe infestation, with an overall accuracy of 82.90% when combined with UAV-HI and LiDAR. [ABSTRACT FROM AUTHOR]

Beijing-Tianjin-Hebei (BTH) has been suffering from severe groundwater storage (GWS) consumption and land subsidence (LS) for a long period. The overexploitation of groundwater brings about severe land subsidence, which affects the safety and development of BTH. In this paper, we utilized multi-frame synthetic aperture radar datasets obtained by the Rardarsat-2 satellite to monitor land subsidence's temporal and spatial distribution in the BTH from 2012 to 2016 based on multi-temporal interferometric synthetic aperture radar (MT-InSAR). In addition, we also employed the Gravity Recovery and Climate Experiment (GRACE) mascon datasets acquired by the Center for Space Research (CSR) and Jet Propulsion Laboratory (JPL) to obtain the GWS anomalies (GWSA) of BTH from 2003 to 2016. Then we evaluate the accuracy of the results obtained. Furthermore, we explored the relationship between the regional GWSA and the average cumulative subsidence in the BTH. The total volume change of subsidence is 59.46% of the total volume change of groundwater storage. Moreover, the long-term decreasing trend of the GWSA (14.221 mm/year) and average cumulative subsidence (17.382 mm/year) show a relatively high consistency. Finally, we analyze the heterogeneity of GWS change (GWSC) and LS change (LSC) in the four typical areas by the Lorenz curve model. The implementation of the South-to-North Water Diversion Project (MSWDP) affects the heterogeneity of GWSC and LSC. It can be seen that the largest heterogeneity of LSC lags behind the GWSC in the Tianjin-Langfang-Hengshui-Baoding area. The largest uneven subsidence in Beijing and Tianjin occurred in 2015, and the largest uneven subsidence in Hengshui-Baoding occurred in 2014. After that, the heterogeneity of subsidence gradually tends to stable. [ABSTRACT FROM AUTHOR]

The Lightning Mapping Imager (LMI) onboard the Fengyun-4A (FY-4A) satellite is the first independently developed satellite-borne lightning imager in China. It enables continuous lightning detection in China and surrounding areas, regardless of weather conditions. The FY-4A LMI uses a Charge-Coupled Device (CCD) array for lightning detection, and the accuracy of lightning positioning is influenced by cloud top height (CTH). In this study, we proposed an ellipsoid CTH parallax correction (ECPC) model for lightning positioning applicable to FY-4A LMI. The model utilizes CTH data from the Advanced Geosynchronous Radiation Imager (AGRI) on FY-4A to correct the lightning positioning data. According to the model, when the CTH is 12 km, the maximum deviation in lightning positioning caused by CTH in Beijing is approximately 0.1177° in the east–west direction and 0.0530° in the north–south direction, corresponding to a horizontal deviation of 13.1558 km, which exceeds the size of a single ground detection unit of the geostationary satellite lightning imager. Therefore, it is necessary to be corrected. A comparison with data from the Beijing Broadband Lightning Network (BLNET) and radar data shows that the corrected LMI data exhibit spatial distribution that is closer to the simultaneous BLNET lightning positioning data. The coordinate differences between the two datasets are significantly reduced, indicating higher consistency with radar data. The correction algorithm decreases the LMI lightning location deviation caused by CTH, thereby improving the accuracy and reliability of satellite lightning positioning data. The proposed ECPC model can be used for the real-time correction of lightning data when CTH is obtained at the same time, and it can be also used for the post-correction of space-based lightning detection with other cloud top height data. [ABSTRACT FROM AUTHOR]

Excessive exploitation of the groundwater has resulted in obvious three-dimensional (3D) deformation features on the surface of the Beijing Plain. This paper, by combining Interferometric Synthetic Aperture Radar (InSAR) and Global Positioning System (GPS) technologies, has obtained time-series information of the 3D surface deformation in the Beijing Plain, analyzing its spatial distribution characteristics. On this basis, the relationship between different controlling factors with the 3D deformation of the surface has been analyzed as well. The following results are obtained: (1) From 2013 to 2018, the land subsidence, which generally showed the trend of slowing down, was mainly concentrated in the eastern, northern, and southern regions of Beijing Plain, with multiple subsidence centers. (2) Under the International Terrestrial Reference Frame 2005 (ITRF2005), the horizontal direction of all GPS points in the plain is basically the same, with the dominant movement direction being NE112.5°~NE113.8°. Under the Eurasian reference frame, the horizontal movement rate of GPS points significantly decreases. The movement rate and direction of each point are not characteristic of overall trend activity. (3) The distribution and extent of the 3D surface deformation in the Beijing Plain are controlled by the basement structure. Part of the subsided area corresponds to a Quaternary depression formed at the junction of active faults disrupting the area. Similarly, the distribution of horizontal deformation in the E-W and N-S directions of the plain is controlled by the regional basement structure comprising major faults bounding horizontal deformation. (4) Groundwater exploitation is the main cause of the 3D surface deformation in the Beijing Plain. The groundwater funnels of the second and third confined aquifer are in suitable agreement with the land subsidence. The horizontal movement in the Beijing Plain is either directed toward the center of the groundwater or the land subsidence funnel, and the deformation is directed from areas with higher to areas with lower groundwater levels. [ABSTRACT FROM AUTHOR]

Based on the resonance fluorescence scattering mechanism, a narrowband sodium (Na) lidar can measure temperature and wind in the mesosphere and lower thermosphere (MLT) region. By using a narrowband spectral filter, background light noise during the day can be suppressed, allowing for continuous observations. To obtain full-diurnal-cycle temperature and wind measurement results, a complex and precise retrieval process is required, along with necessary corrections to minimize measurement errors. This paper introduces the design of a data acquisition unit for three frequencies in three directions of the Na lidar system in the Chinese Meridian Project (Phase II) and investigates the calibration and retrieval methods for obtaining diurnal temperature and horizontal wind in the MLT region, using a Na Doppler lidar with Faraday anomalous dispersion optical filter (FADOF). Furthermore, these methods are applied to observations conducted by a Na lidar in Beijing, China. The wind and temperature results over full diurnal cycles obtained from the all-solid-state Na Doppler lidar are reported for the first time and compared with temperature measurements from satellite, as well as wind observations from a meteor radar. The comparison demonstrates a reasonable agreement between the results, indicating the rationality of the lidar-retrieved results and the feasibility and effectiveness of the data correction and retrieval method. [ABSTRACT FROM AUTHOR]

The urban underlying surface may affect the thunderstorm process. However, current research on this phenomenon is still in its infancy. This paper aimed to analyze the influence of the urban underlying surface on the evolution of thunderstorm organization through ground observation and numerical simulation. The results indicated that when the thunderstorm system with strong synoptic conditions passed through the built-up area of Beijing, it exhibited obvious bifurcation and detour. The dynamic field of near-surface cold pools could serve as diagnostic indicators for understanding how the urban underlying surface affects the thunderstorm process. The large-scale compact-rise clusters in the city center could alter the movement direction and path of the cold pool outflow, thereby influencing the thunderstorm organization process. In addition to the spatial configuration of the building complex, the city size might also be an important factor influencing the thunderstorm process. This study might provide a fundamental foundation and technical support for predicting and assessing urban thunderstorm disasters. [ABSTRACT FROM AUTHOR]

Accurate snowfall forecasting and quantitative snowfall estimation remain challenging due to the complexity and variability of snow microphysical properties. In this paper, the microphysical characteristics of snowfall in the Yanqing mountainous area of Beijing are investigated by using a Particle Size and Velocity (PARSIVEL) disdrometer. Results show that the high snowfall intensity process has large particle-size distribution (PSD) peak concentration, but the distribution of its spectrum width is much smaller than that of moderate or low snowfall intensity. When the snowfall intensity is high, the corresponding D m value is smaller and the N w value is larger. Comparison between the fitted μ − Λ relationship and the relationships of different locations show that there are regional differences. Based on dry snow samples, the Z e − S R relationship fitted in this paper is more consistent with the Z e − S R relationship of dry snow in Nanjing, China. The fitted ρ s − D m relationship of dry snow is close to the relationship in Pyeongchang, Republic of Korea, but the relationship of wet snow shows greatly difference. At last, the paper analyzes the statistics on velocity and diameter distribution of snow particles according to different snowfall intensities. [ABSTRACT FROM AUTHOR]

Urban floods caused by extreme rainstorm events have increased in recent decades, particularly in concave-down bridge zones. To simulate urban flooding processes accurately, an integrated urban flood model (IUFM) was constructed by coupling a distributed urban surface runoff model based on the cellular automata framework (CA-DUSRM), a widely used pipe convergence module in the storm water management model (SWMM), with an inundation module that describes the overflow expansion process associated with terrain and land-cover. The IUFM was used in a case study of the Anhua Bridge (a typical concave-down overpass) study area in Beijing, China. The spatial-temporal variations in flood depth modeled by the IUFM were verified to be reliable by comparison with actual measurements and other simulations. The validated IUFM was used to obtain temporal variations in flood range, depth, and volume under four rainstorm scenarios (return periods of 3-year, 10-year, 50-year, and 100-year). The results showed that the surface runoff process, overflow from drainage networks, and overflow expansion process could affect the flooding status by changing the composition and spatial configuration of pervious or impervious patches, drainage capacity, and underlying surface characteristics (such as terrain and land-cover). Overall, although the simulation results from the IUFM contain uncertainties from the model structures and inputs, the IUFM is an effective tool that can provide accurate and timely information to prevent and control urban flood disasters and provide decision-making support for long-term storm water management and sponge city construction. [ABSTRACT FROM AUTHOR]

Beijing, China's capital city, has experienced decades of severe land subsidence due to the long-term overexploitation of groundwater. The implementation of the South-to-North Water Diversion Project (SNWDP) and artificial ecological restoration have significantly changed Beijing's hydro-ecological and geological environment in recent years, leading to a widespread rise in groundwater levels. However, whether the related land subsidence has slowed down or reversed under these measures has not yet been effectively monitored and quantitatively analyzed in terms of time and space. Accordingly, in this study, we proposed using an improved time-series deformation method, which combines persistent scatterers and distributed scatterers, to process Sentinel-1 images from 2015 to 2022 in the Beijing Plain region. We performed a geospatial analysis to gain a better understanding of how the new hydrological conditions changed the pattern of deformation on the Beijing Plain. The results indicated that our combined PS and DS method provided more measurements both in total quantity and spatial density than conventional PSI methods. The land subsidence in the Beijing Plain area has been effectively alleviated from a subsidence region of approximately 1377 km2 in 2015 to only approximately 78 km2 in 2022. Ecological restoration areas in the northeastern part of the Plain have even rebounded over this period, at a maximum of approximately 40 mm in 2022. The overall pattern of ground deformation (subsidence and uplift) is negatively correlated with changes in the groundwater table (decline and rise). Local deformation is controlled by the thickness of the compressible layer and an active fault. The year 2015, when anthropogenic water transfers were eliminated and ecological measures to recharge groundwater were implemented, was the crucial turning point of the change in the deformation trend in the subsidence history of Beijing. Our findings carry significance, not only for China, but also for other areas where large-scale groundwater extractions are causing severe ground subsidence or rebound. [ABSTRACT FROM AUTHOR]

The Gradient Richardson Number (Ri) is an important parameter for appraising the stability and turbulence exchange at the atmospheric boundary layer (ABL). However, high-resolution measurements of Ri profiles are rarely reported, especially in megacities. In this study, a Doppler wind lidar and a microwave radiometer were simultaneously utilized to measure the 2 km Ri vertical profile in downtown Beijing. These measurements were verified to have high accuracy compared with observations from a 325 m meteorological tower, with root-mean-square errors (RMSEs) of less than 1.66 K, 7.9%, and 1.45 m/s for the temperature, relative humidity, and wind speed (WS) for all altitudes and corresponding Pearson correlation coefficients (R) of 0.97, 0.93, and 0.81. The inter-comparisons of different spatial (25 m, 50 m, 100 m) and temporal resolutions (1 min, 30 min, 1 h) form a 3 × 3 resolution matrix of Ri, in which the 1 h temporal resolution of Ri overestimates the intensity and active area of turbulence. The Ri value retrieved from the 100 m spatial resolution data overestimates these by half as it misidentifies the height of the stable area at the near surface. There are significant differences between the data with a 1 min temporal resolution and a 25 m spatial resolution (defined as the standard resolution of Ri), and the rest of the data in the resolution matrix (defined as data at other resolutions), with an RMSE > 1 and an R < 0.8. The difference between data at the standard resolution and data at other resolutions increases with elevations, which results from frequent weather processes or from water-vapor blocking at higher altitudes. The Ri profiles reveal that the atmospheric layer at altitudes from 100 m to 500 m in daytime is unstable, with Ri < 0, while it is neutral, with 0 < Ri < 0.25, at night-time from 200 m to 400 m. The atmosphere above the ABL in a megacity is rather stable, with Ri > 0.25, whereas below the ABL, it is neutral or unstable, which is due to drastic changes in the WS and temperature that are affected by the topography and surface friction. [ABSTRACT FROM AUTHOR]

The Beijing-Hangzhou Grand Canal in China became a World Cultural Heritage Site in 2014, and the water quality of this ancient man-made canal has increasingly attracted societal attention. This study focuses on monitoring the water quality of the Beijing section of the Grand Canal (BGC) using remote sensing technology. Analysis of the comprehensive trophic level index (TLI) indicates that the water in the Canal was predominantly light eutrophic from 2016 to 2022. The annual average results of the TLI reveal that the water quality in the Kunming Lake and North Canal of BGC is generally good, characterized by some mesotrophic waters, and others are in light eutrophication. The TLI for the entire BGC water body decreased from 64.7 in 2016 to 60.3 in 2022, indicating an improvement trend in water quality. Notably, the proportion of good water with TLI less than 60 increased from 50% in 2016 to 83% in 2022. This improvement of water quality may be attributed to the reduced use of fertilizers and pesticides and the implementation of various environmental policies by Beijing Municipal government. These findings offer valuable insights for the management and protection of the water resources of the BGC, and further contribute to the evaluation of the United Nations Sustainable Development Goal (SDG) 11.4. [ABSTRACT FROM AUTHOR]

With the rapid development of microwave remote sensing and SAR satellite systems, the use of InSAR techniques has been greatly encouraged due to the abundance of SAR data with unprecedented temporal and spatial coverage. Small Baseline Subset (SBAS) is a promising time-series InSAR method for applications involving deformation monitoring of the Earth's crust, and the sequential SBAS method is an extension of SBAS that allows long-term and large-scale surface displacements to be obtained with continuously auto-updating measurement results. As the Chinese LuTan-1 SAR system has begun acquiring massive SAR image data, the need for an efficient and lightweight InSAR processing platform has become urgent in various research fields. However, traditional sequential algorithms are incapable of meeting the huge challenges of low efficiency and frequent human interaction in large-scale InSAR data processing. Therefore, this study proposes a distributed parallel sequential SBAS (P2SBAS) processing chain based on Hadoop by effectively parallelizing and improving the current sequential SBAS method. P2SBAS mainly consists of two components: (1) a distributed SAR data storage platform based on HDFS, which supports efficient inter-node data transfer and continuous online data acquisition, and (2) several parallel InSAR processing algorithms based on the MapReduce model, including image registration, filtering, phase unwrapping, sequential SBAS processing, and so on. By leveraging the capabilities associated with the distributed nature of the Hadoop platform, these algorithms are able to efficiently utilize the segmentation strategy and perform careful boundary processing. These parallelized InSAR algorithm modules can achieve their goals on different nodes in the Hadoop distributed environment, thereby maximizing computing resources and improving the overall performance while comprehensively considering performance and precision. In addition, P2SBAS provides better computing and storage capabilities for small- and medium-sized teams compared to popular InSAR processing approaches based on cloud computing or supercomputing platforms, and it can be easily deployed on clusters thanks to the integration of various existing computing components. Finally, to demonstrate and evaluate the efficiency and accuracy of P2SBAS, we conducted comparative experiments on a set of 32 TerraSAR images of Beijing, China. The results demonstrate that P2SBAS can fully utilize various computing nodes to improve InSAR processing and can be applied well in large-scale LuTan-1 InSAR applications in the future. [ABSTRACT FROM AUTHOR]

Migratory waterbirds depend on a complex network of wetlands globally for their life cycles. However, habitat loss and degradation pose risks to these networks' sustainability, potentially impacting wetland habitat availability. This study investigates the impact of water level changes in Beijing's Miyun Reservoir on white-naped cranes' (Antigone vipio) habitat use. We utilized satellite imagery from 2000–2021 and monthly data from 2018–2023 to observe changes in the reservoir's water and land areas. Additionally, the study tracked 32 cranes using GSM-GPS loggers, yielding insights into their movement patterns and habitat preferences. Our findings emphasize the significant influence of reservoir water levels on habitat availability for these cranes. Notably, our results indicate that the decrease in suitable migratory bird habitats in the reservoir is primarily attributed to high-water level management strategies. This study highlights the necessity for balanced management of aquatic and terrestrial areas in reservoir ecosystems to preserve migratory waterbird habitats. [ABSTRACT FROM AUTHOR]

Land surface temperature (LST) is one of the most important parameters of the interface between the earth surface and the atmosphere, and it plays a significant role in many research fields, such as agriculture, climate, hydrology, and the environment. However, the thermal infrared band of remote sensors is easily affected by clouds and aerosols, leading to many data gaps in LST products, which restricts the subsequent application of these products. In this paper, Beijing, China, is selected as the study area, and the LST data retrieved from Fengyun 4A (FY-4A) Advanced Geosynchronous Radiation Imager (AGRI) are reconstructed based on the two-point machine learning method. Firstly, the two-point machine learning model is built to reconstruct the theoretical clear-sky LST from simulated and actual images, and the accuracy of the reconstruction results is evaluated compared with the random forest algorithm and the inverse distance weighted method. Secondly, the actual LST under the influence of clouds is reconstructed by using the ERA5 reanalysis LST data as the auxiliary data, and the reconstruction accuracy is then evaluated by the field measurement LST data. The experimental results show that (1) the prediction accuracy of the two-point machine learning method is higher than that of the random forest method in both simulated data and actual data experiments; (2) the R2 of reconstructed LST under theoretical clear-sky conditions is 0.6860 and the root mean square error (RMSE) is 2.9 K, while the R2 of the reconstructed accuracy of actual LST under clouds is 0.7275 and the RMSE is 2.6 K, i.e., the RMSE decreases by 10.34%; (3) the two-point machine method combined with the auxiliary ERA5 LST data can well reconstruct LST under cloudy conditions and present a reasonable LST distribution. [ABSTRACT FROM AUTHOR]

Satellite-derived aerosol optical depth (AOD) has been extensively utilized for retrieving ground-level PM2.5 distributions. However, the presence of non-random missing data gaps in AOD poses a challenge to directly obtaining the gap-free AOD-derived PM2.5, thereby impeding accurate exposure risk assessment. Here, this study presents a novel and flexible framework that couples stacking and flexible spatiotemporal data fusion (FSDAF) approaches. By integrating multiple models and data sources, this framework aims to generate hourly (24-h) gap-free PM2.5 estimates for the Beijing–Tianjin–Hebei (BTH) region in 2018. This study effectively reconstructed data at least three times more effectively than the original AOD-derived PM2.5, achieving the Pearson coefficient (r), the coefficient determination (R2), root mean squared error (RMSE), and mean absolute error (MAE) values of 0.91, 0.84, 19.38 µg/m3, and 12.17 µg/m3, respectively, based on entire samples. Such strong predictive performance was also exhibited in spatial-based (r: 0.92–0.93, R2: 0.85–0.87, RMSE: 18.13 µg/m3–20.18 µg/m3, and MAE: 11.21 µg/m3–12.52 µg/m3) and temporal-based (r: 0.91–0.98, R2: 0.82–0.96, RMSE: 3.8 µg/m3–21.89 µg/m3, and MAE: 2.71 µg/m3–14.00 µg/m3) validations, indicating the robustness of this framework. Additionally, this framework enables the assessment of annual and seasonal PM2.5 concentrations and distributions, revealing that higher levels are experienced in the southern region, while lower levels prevail in the northern part. Winter exhibits the most severe levels, followed by spring and autumn, with comparatively lower levels in summer. Notably, the proposed framework effectively mitigates bias in calculating population-weighted exposure risk by filling data gaps with calculated values of 51.04 µg/m3, 54.17 µg/m3, 56.24 µg/m3, and 55.00 µg/m3 in Beijing, Tianjin, Hebei, and the BTH region, respectively. [ABSTRACT FROM AUTHOR]

Extreme weather events are happening more frequently as a result of global climate change. Dust storms broke out in the spring of 2017 in China and drastically impacted the local air quality. In this study, a variety of data, including aerosol vertical profiles, surface particle concentration, meteorological parameters, and MODIS–derived aerosol optical depth, as well as backward trajectory analysis, were employed to analyze two dust events from April to May in Beijing. The dust plumes were mainly concentrated below 0.8 km, with peak PM10 values of 1000 μg·m−3 and 300 μg·m−3 in the two cases. The aerosols showed different vertical distribution characteristics. The pure dust in case 1 from 4 to 5 May 2017 had a longer duration (2 days) and presented a larger aerosol extinction coefficient (2.27 km−1 at 355 nm and 1.25 km−1 at 532 nm) than that of the mixed dust in case 2 on 17 April 2017 (2.01 km−1 at 355 nm and 1.33 km−1 at 532 nm). The particle depolarization ratio (PDR) remained constant (0.24 ± 0.03 in case 1) from the surface to 0.8 km in height. In contrast, the PDR profile in the mixed dust (case 2) layer was split into two regions—large values exceeding 0.15 above 0.6 km and small values of 0.11 ± 0.03 below 0.6 km. The influence of meteorological information on aerosol distribution was also investigated, and wind was predominant through the observing period. The pure dust in case 1 was mainly from Mongolia, with strong northwest winds, while the near-surface mixed pollution was caused by the combination of long-transported sand and local emission. Furthermore, lidar-derived profiles of dust mass concentrations in the two cases were presented. This study reveals the vertical characteristics of dust aerosols in the production and dissipation of localized dust events and confirms the efficacy of thorough observations with multiple approaches from the ground to space to monitor dust events in real time. [ABSTRACT FROM AUTHOR]

Real-time and high-precision water level monitoring is crucial for the fields of hydrology, hydraulic engineering, and disaster prevention and control. The most prevalent method for measuring water level is through the use of water level gauges, which can be costly and have limited coverage. In recent years, Global Navigation Satellite System Reflectometry (GNSS-R) technology has emerged as a promising approach for water level monitoring due to its low cost and high coverage. However, a limitation of current GNSS-R technology is the extended time required to record signals, which hinders its potential for real-time application. This paper introduces a novel real-time water level monitoring method based on GNSS dual-antenna attitude measurement and develops a model to invert water level based on baseline vector. This method uses double-difference observations to eliminate errors caused by various factors, such as satellite and receiver clock, and ionospheric and tropospheric delay. To avoid the impact of detecting and correcting cycle slips during real-time operations, a single-epoch calculation method is introduced. In order to verify the stability and reliability of our method, field tests were carried out at Dongshahe Station in Beijing. We obtained water level data with a time resolution of 1 Hz through field experiments. Experimental data collected from 12 May to 8 June 2022 and from 4 July to 8 August 2022 showed good agreement with on-site water gauge measurements, with root mean square errors of 2.77 cm and 2.54 cm, respectively. Experimental results demonstrate that this method can achieve high-precision, high-temporal-resolution water level monitoring. [ABSTRACT FROM AUTHOR]

In metropolitan areas, the static load of high-rise buildings may result in uneven settlement, which seriously threatens residents' living safety. Studying the response relationship between the additional stress of high-rise buildings and foundation settlement plays an important role in ensuring the safe development of metropolitan cities. Firstly, based on Persistent Scatterers Interferometric Aperture Radar (PS-InSAR) technology, we used 68 descending TerraSAR-X images to obtain the surface settlement in the study area from April 2010 to October 2018, which were validated with leveling benchmark monitoring results. Secondly, we calculated the additional stress of the building loads to quantify its effect on the uneven settlement in the Central Business District (CBD) of Beijing. Finally, two sets of characteristic points were selected to analyze the response relationships between foundation settlement and additional stress generated by building loads. The findings show: (1) The surface settlement rate varied from −145.2 to 24 mm/year in the Beijing Plain. The InSAR results agree well with the monitoring results derived from the leveling benchmark; the Pearson correlation coefficients were 0.98 and 0.95 in 2011–2013 and 2015–2016, respectively. (2) The stress results show that the depth of the influence of the static load of high-rise buildings was 74.9 m underground in the CBD. (3) The spatial distribution pattern of the additional stress is consistent with the foundation settlement. A characteristic point with greater additional stress in the same group has a higher foundation settlement rate. This relationship has also been found between the uneven foundation settlement and additional stress gradients. These findings provide scientific support for mitigating economic losses due to foundation settlement caused by additional stresses derived from building loads. [ABSTRACT FROM AUTHOR]

As an essential material carrier of cultural heritage, the accurate identification and effective monitoring of buildings in traditional Chinese villages are of great significance to the sustainable development of villages. However, along with rapid urbanization in recent years, many towns have experienced problems such as private construction, hollowing out, and land abuse, destroying the traditional appearance of villages. This study combines deep learning technology and UAV remote sensing to propose a high-precision extraction method for conventional village architecture. Firstly, this study constructs the first sample database of traditional village architecture based on UAV remote sensing orthophotos of eight representative villages in Beijing, combined with fine classification; secondly, in the face of the diversity and complexity of the built environment in traditional villages, we use the Mask R-CNN instance segmentation model as the basis and Path Aggregate Feature Pyramid Network (PAFPN) and Atlas Space Pyramid Pool (ASPP) as the main strategies to enhance the backbone model for multi-scale feature extraction and fusion, using data increment and migration learning as auxiliary means to overcome the shortage of labeled data. The results showed that some categories could achieve more than 91% accuracy, with average precision, recall, F1-score, and Intersection over Union (IoU) values reaching 71.3% (+7.8%), 81.9% (+4.6%), 75.7% (+6.0%), and 69.4% (+8.5%), respectively. The application practice in Hexi village shows that the method has good generalization ability and robustness, and has good application prospects for future traditional village conservation. [ABSTRACT FROM AUTHOR]

For large-scale 3D building reconstruction, there have been several approaches to utilizing multi-view satellite imagery to produce a digital surface model (DSM) for height information and extracting building footprints for contour information. However, limited by satellite resolutions and viewing angles, the corresponding DSM and building footprints are sometimes of a low accuracy, thus generating low-accuracy building models. Though some recent studies have added GIS data to refine the contour of the building footprints, the registration errors between the GIS data and satellite images are not considered. Since OpenStreetMap (OSM) provides a high level of precision and complete building polygons in most cities worldwide, this paper proposes an automatic single building reconstruction method that utilizes a DSM from high-resolution satellite stereos, as well as building footprints from OSM. The core algorithm accurately registers the building polygons from OSM with the rasterized height information from the DSM. To achieve this goal, this paper proposes a two-step "coarse-to-fine registration" algorithm, with both steps being formulated into the optimization of energy functions. The coarse registration is optimized by separately moving the OSM polygons at fixed steps with the constraints of a boundary gradient, an interior elevation mean, and variance. Given the initial solution of the coarse registration, the fine registration is optimized by a genetic algorithm to compute the accurate translations and rotations between the DSM and OSM. Experiments performed in the Beijing/Shanghai region show that the proposed method can significantly improve the IoU (intersection over union) of the registration results by 69.8%/26.2%, the precision by 41.0%/15.5%, the recall by 41.0%/16.0%, and the F1-score by 42.7%/15.8%. For the registration, the method can reduce the translation errors by 4.656 m/2.815 m, as well as the rotation errors by 0.538°/0.228°, which indicates its great potential in smart 3D applications. [ABSTRACT FROM AUTHOR]

Seasonal and diurnal characteristics of the vertical profiles of aerosol properties are essential for detecting the regional transport and the climatic radiative effects of aerosol particles. We have studied the seasonal and diurnal characteristics of the vertical distribution of aerosols in urban Beijing from 2017 to 2021 based on long-term Raman–Mie LiDAR observations. The influence of the vertical distribution of aerosols, the meteorological conditions within the boundary layer, the optical–radiometric properties of aerosols, and their interconnections, were investigated during a heavy haze pollution event in Beijing from 8 to 15 February 2020 using both meteorological and sun photometer data. The aerosol extinction coefficient was highest in summer (0.4 km−1), followed by winter (0.35 km−1), and roughly equal in spring and autumn (0.3 km−1). The aerosol extinction coefficient showed clear daily variations and was different in different seasons as a result of the variation in the height of the boundary layer. During the haze pollution event, the particulate matter mainly consisted of scattered spherical fine particles and the accumulation time of pollutants measured via the AOD440nm and PM2.5 mass concentration was different as a result of the hygroscopic growth of the aerosol particles. This growth increased scattering and led to an increase in the aerosol optical depth. The vertical transport of particulate matter also contributed to the increase in the aerosol optical depth. [ABSTRACT FROM AUTHOR]

Albedo is one of the key parameters in the surface energy balance and it has been altered due to urban expansion, which has significant impacts on local and regional climate. Many previous studies have demonstrated that changes in the urban surface albedo are strongly related to the city's heterogeneity and have significant spatial-temporal characteristics but fail to address the albedo of the urban surface as a unique variable in urban thermal environment research. This study selects Beijing as the experimental area for exploring the spatial-temporal characteristics of the urban surface albedo and the albedo's uniqueness in environmental research on urban spaces. Our results show that the urban surface albedo at high spatial resolution can better represent the urban spatial heterogeneity, seasonal variation, building canyon, and pixel adjacency effects. Urban surface albedo is associated with building density and height, land surface temperature (LST), and fractional vegetation cover (FVC). Furthermore, albedo can reflect livability and environmental rating due to the variances of building materials and architectural formats in the urban development. Hence, we argue that the albedo of the urban surface can be considered as a unique variable for improving the acknowledgment of the urban environment and human livability with wider application in urban environmental research. [ABSTRACT FROM AUTHOR]

The eastern Beijing plain has been suffering severe subsidence for the last decades, mainly associated with the long-term excessive extraction of groundwater resource. Since the end of 2014, the annual water supply in Beijing plain has reached several hundred million cubic meters because of the South-to-North Water Diversion (SNWD) Project, which has reduced the groundwater exploitation and changed the status of land subsidence. In this work, we first obtain the current spatiotemporal variations of land subsidence in the eastern Beijing plain by using progressive small baseline subsets (SBAS) InSAR time series analysis method with Sentinel-1 SAR data acquired from July 2015 to December 2021. Then, we analyze the correlations between InSAR-derived subsidence and groundwater level change by applying the cross wavelet method. The results show that two major subsidence zones are successfully detected with the maximum deformation rate of −150 mm/yr and maximum cumulative deformation of −950 mm. Besides, the ground deformation at different stages from 2016 to 2021 reveal that the area and magnitude of major deformation significantly slow down, even in the regions with severe subsidence, especially in the year of 2017, which is about two years later than the start time of SNWD Project in Beijing. Further, we find the InSAR-derived subsidence lags groundwater level change with about 1–2-month lagging time, indicating that the dynamic variation of groundwater level fluctuation may be the main factor affecting the uneven subsidence in the severe subsiding zones. Last, differential subsidence rates are identified at both sides of geological faults, such as Nankou-Sunhe fault and Nanyuan-Tongxian fault, from the observed deformation map, which could be explained that the groundwater flow is blocked when a fault is encountered. These findings can provide significant information to reveal the deformation mechanisms of land subsidence, establish the hydrogeological models and assist decision-making, early warning and hazard relief in Beijing, China. [ABSTRACT FROM AUTHOR]

The Xishan coal mine area in Beijing, China has a long history of mining. Many landslide hazards, in addition to collapses and ground fractures, have occurred in this area. This study used multi-temporal satellite images to extract this region's deformation information, identify landslides and analyze the deformation evolution process of these landslides. Taking the Anzigou ditch as an example, we investigate the "Quarry–Landslide–Mudslide" disaster chain model. We found that the landslide evolution process is closely related to the geological conditions, and usually goes through four stages: initial deformation, slope front swelling and collapsing, rear part connecting and rupturing, and landslide creeping. The surface deformation can be identified and tracked by high-resolution optical images and InSAR monitoring. Under the combined effects of rainfall and topographic conditions, medium and large landslides may occur and trigger a "Quarry–Landslide–Mudflow" disaster chain. The identification and analysis of these landslide hazards and the disaster chain help with geological disaster prevention, and provide reference for early identification and research of similar disasters. [ABSTRACT FROM AUTHOR]

Rapid and accurate mapping of winter wheat using remote sensing technology is essential for ensuring food security. Most of the existing studies have failed to fully characterize the phenological features of winter wheat in mapping, resulting in low classification accuracy. To this end, this study developed a new multiple phenological spectral feature (Mpsf) and then used the generated new features as input data for a one-class classifier (One-Class Support Vector Machine, OCSVM) to map winter wheat. The main steps in this work are as follows: (1) Identifying key phenological periods. The spectral indices temporal profiles of winter wheat (after cloud masking) were drawn separately using different spectral indices, and the key phenological periods of winter wheat were identified with a priori knowledge of phenology. (2) Composition for a new feature. Composited the spectral features of winter wheat for each key phenological period to generate a new feature. (3) Training using a one-class classifier. The new feature was put into OCSVM for training, and the final winter wheat mapping result in the Beijing region was obtained. The cost of this new winter wheat mapping method is low and the accuracy is high. To verify the accuracy of this study, we compared the Mpsf map with three kinds of reference data, and all of them got good results. In comparison, with ground truth samples from Sentinel-2, the total accuracy was overall higher than 97.9%. The relative error of the 2019 winter wheat mapping result was only 0.51%, compared with the data from the Beijing Bureau of Statistics. In comparison, with an up-to-date available winter wheat-mapping product for Beijing (spatial resolution: 30 m), the Mpsf map has significantly fewer misclassifications. To our knowledge, this study produced one of the highest accuracy winter wheat-mapping products in Beijing for 2018 and 2019 to date. In general, we hope that this work can promote the development of winter wheat mapping and provide a reference for sustainable agricultural development and governmental decision-making. [ABSTRACT FROM AUTHOR]

Inland lakes or reservoirs are the main surface water resources, related to people's survival and social development. On-site water level data are critical for water resource management, while satellite laser and remote sensing data are a significant tool for long-term change monitoring. In this study, we took the Miyun Reservoir, the most important source of drinking water in Beijing, as the research area. We used Landsat images and the Ice, Cloud, and Land Elevation Satellite (ICESat-2) for small-scale water level change monitoring and inversion across unrecorded periods. First, we proposed a new two-step denoising method based on local statistics to denoise the ATL03 single photon data from 2018 to 2020, and extracted the effective elevation information of Miyun Reservoir. Second, based on Landsat images from 1984 to 2020, the MNDWI index was used to extract the water area and generated a percentage map of water occurrence. Finally, the water and land boundary elevation were selected from the effective photon elevation information according to the boundary position under each percentage of the water generation percentage graph, the area, and the water level elevation model (A–E model) was established, and the water level values of unrecorded periods were inverted. The denoising results showed that the denoising accuracy of all data is higher than 95%. The area of Miyun Reservoir has changed greatly in the past 37 years, especially in the northeast corner and northern region. The inverted water level elevation had a strong correlation with the measured value, the correlation coefficient reached 0.97, the root mean square error (RMSE) was 0.553 m, and the estimated water level value was highly consistent with the recorded value and fluctuated dramatically from 1984 to 2020. This method complements the traditional water level mapping method, provides a new idea for the monitoring of water level changes in lakes or reservoirs without field records, and also contributes to the timely and effective monitoring and management of global lake and reservoir water level and time changes. [ABSTRACT FROM AUTHOR]

Understanding the change in hydrological response due to urban dynamics is important for better flood preparedness and future sustainable urban planning. This study investigated the influence of urban land cover change on spatiotemporal changes in flood peak discharge and flood volume within a rapidly urbanizing catchment located in Beijing, China. We used Landsat satellite data ranging from 1986 to 2017 to monitor and quantify urban growth. Moreover, the Hydrological Modeling System (HEC-HMS) coupled with meteorological data was utilized to examine the impact of urban growth on hydrological responses. The results revealed that major changes in land use/cover (LULC) were detected in the urban landscape, which increased from 25.22% to 65.48% of the total catchment area, while agricultural land decreased from 64.85% to 25.28% during 1986–2017. The flood peak discharge and flood volume average of the three rainstorms events reached 7.02% and 11.93%, respectively. Furthermore, the changes in flood peak discharge and flood volume were more obvious at the sub-catchment scale. These findings indicate that urban growth enhanced the possible flooding risk in the study catchment. This study improves the understanding of the isolated impacts of urbanization on flooding and provides essential information for sustainable urban planning. [ABSTRACT FROM AUTHOR]

Numerical weather prediction (NWP) has become an important method of predicting extreme weather events, but orography is one of the key factors affecting the performance of NWPs. In this paper, based on Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) elevation data, a method for constructing a global orographic dataset suitable for NWP spectral models is investigated. The Yin-He global spectrum model (YHGSM) is used to simulate the early and peak periods of the extreme rainfall event on 20 July 2021 in Henan Province, China, and the heavy rain in Beijing in order to verify the effectiveness and superiority of the proposed orographic construction method. It is demonstrated that in a few cases the direct two-dimensional filter can sometimes simulate more intense rainfall, but in general, the bidirectional one-dimensional filter is better than the direct two-dimensional filter in orographic processing, and the bidirectional one-dimensional filter can filter out more of the small-scale orographic information. The effect of the higher orographic resolution before conversion to spectral space is not very obvious, but it is demonstrated that the simulation results are better for the heavy-rainfall level. In conclusion, in most cases, the simulations conducted using the new global orographic dataset based on ASTER data are better than those obtained using the model's original orography, especially for torrential and extreme rainfall. These conclusions provide a reference for future predictions of and research on extreme rainfall events. [ABSTRACT FROM AUTHOR]

Accurate spatial population distribution information, especially for metropolises, is of significant value and is fundamental to many application areas such as public health, urban development planning and disaster assessment management. Random forest is the most widely used model in population spatialization studies. However, a reliable model for accurately mapping the spatial distribution of metropolitan populations is still lacking due to the inherent limitations of the random forest model and the complexity of the population spatialization problem. In this study, we integrate gradient boosting decision tree (GBDT), extreme gradient boosting (XGBoost), light gradient boosting machine (LightGBM) and support vector regression (SVR) through ensemble learning algorithm stacking to construct a novel population spatialization model we name GXLS-Stacking. We integrate socioeconomic data that enhance the characterization of the population's spatial distribution (e.g., point-of-interest data, building outline data with height, artificial impervious surface data, etc.) and natural environmental data with a combination of census data to train the model to generate a high-precision gridded population density map with a 100 m spatial resolution for Beijing in 2020. Finally, the generated gridded population density map is validated at the pixel level using the highest resolution validation data (i.e., community household registration data) in the current study. The results show that the GXLS-Stacking model can predict the population's spatial distribution with high precision (R2 = 0.8004, MAE = 34.67 persons/hectare, RMSE = 54.92 persons/hectare), and its overall performance is not only better than the four individual models but also better than the random forest model. Compared to the natural environmental features, a city's socioeconomic features are more capable in characterizing the spatial distribution of the population and the intensity of human activities. In addition, the gridded population density map obtained by the GXLS-Stacking model can provide highly accurate information on the population's spatial distribution and can be used to analyze the spatial patterns of metropolitan population density. Moreover, the GXLS-Stacking model has the ability to be generalized to metropolises with comprehensive and high-quality data, whether in China or in other countries. Furthermore, for small and medium-sized cities, our modeling process can still provide an effective reference for their population spatialization methods. [ABSTRACT FROM AUTHOR]

The lower atmosphere forcing plays an important role in forming the sporadic E (Es) layer in the ionosphere. In this study, a comparative study of the Es layer recorded by ionosondes at the middle latitude regions was carried out between the plateau and plain regions in China. The two ionosonde stations (Zhangye, 39.21°N, 100.54°E and Beijing, 40.25°N, 116.25°E) are located at the Qinghai–Tibet Plateau and North China Plain, respectively. The data during the year 2018 were used to reveal the characteristics of the Es layer. The occurrence probability, the critical frequency (foEs) and the base virtual height (h'Es) were considered in this study. Results show that: (1) The diurnal and seasonal variations of the occurrence probability between these two regions are similar. The maximum occurrence probability is at noontime and in the summer season. However, the Es at Zhangye occurred more frequently than Beijing at nighttime and in winter to early spring. (2) Similar to previous studies, the maximum value of foEs at Beijing mainly occurred in summer. Interestingly, the maximum value is in winter at Zhangye station. (3) The characteristics of the anomaly of the Es layer at Zhangye are mostly consistent with the characteristics of atmospheric gravity waves in the Qinghai–Tibet Plateau. Therefore, compared with observations at Beijing, the anomalies of the Es layer at Zhangye (at night and in winter to spring) might be attributed to gravity waves in the lower atmosphere over the Qinghai–Tibet Plateau. [ABSTRACT FROM AUTHOR]

Extreme precipitation events have a more serious impact on densely populated cities and therefore reliable estimation of extreme precipitation is very important. Satellite-derived precipitation products provide precipitation datasets with high spatiotemporal resolution. For improved applicability to estimating urban extreme precipitation, the performance of such products must be evaluated regionally. This study evaluated three satellite-derived precipitation products, the Integrated Multi-satellite Retrievals for GPM (IMERG_V06), Multi-Source Weighted-Ensemble Precipitation (MSWEP V2), and China Meteorological Forcing Dataset (CMFD), in capturing extreme precipitation using observations acquired at 36 rainfall stations during 2001–2016 in Beijing, China. Results showed that MSWEP had the highest accuracy regarding daily precipitation data, with the highest correlation coefficient and the lowest absolute deviation between MSWEP and the rainfall station observations. CMFD demonstrated the best ability for correct detection of daily precipitation events, while MSWEP maintained the lowest rate of detecting non-rainy days as rainy days. MSWEP performed better in estimating precipitation amount and the number of precipitation days when daily precipitation was <50 mm; CMFD performed better when daily precipitation was >50 mm. All three products underestimated extreme precipitation. The Structural Similarity Index, which is a map comparison technique, was used to compare the similarities between the three products and rainfall station observations of two extreme rainstorms: "7.21" in 2012 and "7.20" in 2016. MSWEP and CMFD showed higher levels of similarity in terms of spatial–temporal structure. Overall, despite systematic underestimation, MSWEP performed better than IMERG and CMFD in estimating extreme precipitation in Beijing. [ABSTRACT FROM AUTHOR]