Search

In this paper, we demonstrate the capabilities of Pleiades-1a imagery for very high resolution (VHR) crop yield estimation by utilizing the predictor variables from the horizontal-spectral information, through Normalized Difference Vegetation Indices (NDVI), and the vertical-volumetric crop characteristics, through the derivation of Crop Canopy Models (CCMs), from the stereo imaging capacity of the satellite. CCMs captured by Unmanned Aerial Vehicles are widely used in precision farming applications, but they are not suitable for the mapping of large or inaccessible areas. We further explore the spatiotemporal relationship of the CCMs and the NDVI for five observation dates during the growing season for eight selected crop fields in Germany with harvester-measured ground truth crop yield. Moreover, we explore different CCM normalization methods, as well as linear and non-linear regression algorithms, for the crop yield estimation. Overall, using the Extremely Randomized Trees regression, the combination of CCMs and NDVI achieves an R2 coefficient of determination of 0.92. [ABSTRACT FROM AUTHOR]

Nationwide and consistent information on agricultural land use forms an important basis for sustainable land management maintaining food security, (agro)biodiversity, and soil fertility, especially as German agriculture has shown high vulnerability to climate change. Sentinel-1 and Sentinel-2 satellite data of the Copernicus program offer time series with temporal, spatial, radiometric, and spectral characteristics that have great potential for mapping and monitoring agricultural crops. This paper presents an approach which synergistically uses these multispectral and Synthetic Aperture Radar (SAR) time series for the classification of 17 crop classes at 10 m spatial resolution for Germany in the year 2018. Input data for the Random Forest (RF) classification are monthly statistics of Sentinel-1 and Sentinel-2 time series. This approach reduces the amount of input data and pre-processing steps while retaining phenological information, which is crucial for crop type discrimination. For training and validation, Land Parcel Identification System (LPIS) data were available covering 15 of the 16 German Federal States. An overall map accuracy of 75.5% was achieved, with class-specific F1-scores above 80% for winter wheat, maize, sugar beet, and rapeseed. By combining optical and SAR data, overall accuracies could be increased by 6% and 9%, respectively, compared to single sensor approaches. While no increase in overall accuracy could be achieved by stratifying the classification in natural landscape regions, the class-wise accuracies for all but the cereal classes could be improved, on average, by 7%. In comparison to census data, the crop areas could be approximated well with, on average, only 1% of deviation in class-specific acreages. Using this streamlined approach, similar accuracies for the most widespread crop types as well as for smaller permanent crop classes were reached as in other Germany-wide crop type studies, indicating its potential for repeated nationwide crop type mapping. [ABSTRACT FROM AUTHOR]

Nighttime lights are routinely used as a proxy for economic activity when official statistics are unavailable and are increasingly applied to study the effects of shocks or policy interventions at small geographic scales. The implicit assumption is that the ability of nighttime lights to pick up changes in GDP does not depend on local characteristics of the region under investigation or the scale of aggregation. This study uses panel data on regional GDP growth from six countries, and nighttime lights from the Defense Meteorological Satellite Program (DMSP) to investigate potential nonlinearities and measurement errors in the light production function. Our results for high statistical capacity countries (the United States and Germany) show that nightlights are significantly less responsive to changes in GDP at higher baseline level of GDP, higher population densities, and for agricultural GDP. We provide evidence that these nonlinearities are too large to be caused by differences in measurement errors across regions. We find similar but noisier relationships in other high-income countries (Italy and Spain) and emerging economies (Brazil and China). We also present results for different aggregation schemes and find that the overall relationship, including the nonlinearity, is stable across regions of different shapes and sizes but becomes noisier when regions become few and large. These findings have important implications for studies using nighttime lights to evaluate the economic effects of shocks or policy interventions. On average, nighttime lights pick up changes in GDP across many different levels of aggregation, down to relatively small geographies. However, the nonlinearity we document in this paper implies that some studies may fail to detect policy-relevant effects in places where lights react little to changes in economic activity or they may mistakenly attribute this heterogeneity to the treatment effect of their independent variable of interest. [ABSTRACT FROM AUTHOR]

Many analyses of the perturbed ionospheric D-region and its influence on the propagation of ground-based and satellite signals are based on data obtained in ionospheric remote sensing by very low/low frequency (VLF/LF) signals. One of the most significant causes of errors in these analyses is the lack of data related to the analysed area and time period preceding the considered perturbation. In this paper, we examine the influence of the estimation of the quiet ionosphere parameters on the determination of the electron density (Ne) and total electron content in the D-region (TECD) during the influence of a solar X-ray flare. We present a new procedure in which parameters describing the quiet ionosphere are calculated based on observations of the analysed area by a VLF/LF signal at the observed time. The developed procedure is an upgrade of the quiet ionospheric D-region (QIonDR) model that allows for a more precise analysis of the D-region intensively perturbed by a solar X-ray flare. The presented procedure is applied to data obtained in ionospheric remote sensing by the DHO signal emitted in Germany and received in Serbia during 30 solar X-ray flares. We give analytical expressions for the dependencies of the analysed parameters on the X-ray flux maximum at the times of the X-ray flux maximum and the most intense D-region perturbation. The results show that the obtained Ne and TECD are larger than in the cases when the usual constant values of the quiet ionosphere parameters are used. [ABSTRACT FROM AUTHOR]

Synthetic Aperture Radar (SAR) measurements are unique for mapping forest 3D structure and its changes in time. Tomographic SAR (TomoSAR) configurations exploit this potential by reconstructing the 3D radar reflectivity. The frequency of the SAR measurements is one of the main parameters determining the information content of the reconstructed reflectivity in terms of penetration and sensitivity to the individual vegetation elements. This paper attempts to review and characterize the structural information content of L-band TomoSAR reflectivity reconstructions, and their potential to forest structure mapping. First, the challenges in the accurate TomoSAR reflectivity reconstruction of volume scatterers (which are expected to dominate at L-band) and to extract physical structure information from the reconstructed reflectivity is addressed. Then, the L-band penetration capability is directly evaluated by means of the estimation performance of the sub-canopy ground topography. The information content of the reconstructed reflectivity is then evaluated in terms of complementary structure indices. Finally, the dependency of the TomoSAR reconstruction and of its structural information to both the TomoSAR acquisition geometry and the temporal change of the reflectivity that may occur in the time between the TomoSAR measurements in repeat-pass or bistatic configurations is evaluated. The analysis is supported by experimental results obtained by processing airborne acquisitions performed over temperate forest sites close to the city of Traunstein in the south of Germany. [ABSTRACT FROM AUTHOR]

The analysis of soil and land cover scattering properties and their connection with the parameters of microwave scattering is a longstanding research topic. Recently, the advent of modern space-borne microwave radiometers like SMAP in addition to the trend towards open data for scientific use fostered the development of enhanced models based on data fusion from different platforms permitting more accurate assessments. SMAP was designed to operate on an integrated combination of a radiometer and a radar, both operating in L-band. Unexpected failure of the radar component encouraged scientists to experiment various combination of data from the surviving radiometer with other sources of radar data, notably C-band Sentinel-1 data. In this work, we present a case study on a possible combination of SMAP radiometer data with X-band radar data from TerraSAR-X and COSMO-SkyMed, comparing results with those provided by NASA from their standard production procedures. The study was performed on two test sites, one at an agricultural site in Germany and one in the Brazilian Amazon, to explore very different vegetation conditions. This work is a part of a broader research effort addressing the combination of multiple sources of passive and active microwave sensing data. The research question defining this research effort is whether the use of data from multiple active sources affords either obtaining more accurate estimates of active–passive co-variation parameters for a given observation period, or shortening the minimum observation period by increasing the temporal density of active samples. In this framework, this paper addresses a preliminary comparison of fresh and past results obtained from C-, X-, and L-band active sensing data. The observed relations offer interesting clues on the impact of band selection on soil vegetation analysis. [ABSTRACT FROM AUTHOR]

In this paper, we present the estimation of surface NO 2 concentrations over Germany using a machine learning approach. TROPOMI satellite observations of tropospheric NO 2 vertical column densities (VCDs) and several meteorological parameters are used to train the neural network model for the prediction of surface NO 2 concentrations. The neural network model is validated against ground-based in situ air quality monitoring network measurements and regional chemical transport model (CTM) simulations. Neural network estimation of surface NO 2 concentrations show good agreement with in situ monitor data with Pearson correlation coefficient (R) of 0.80. The results also show that the machine learning approach is performing better than regional CTM simulations in predicting surface NO 2 concentrations. We also performed a sensitivity analysis for each input parameter of the neural network model. The validated neural network model is then used to estimate surface NO 2 concentrations over Germany from 2018 to 2020. Estimated surface NO 2 concentrations are used to investigate the spatio-temporal characteristics, such as seasonal and weekly variations of NO 2 in Germany. The estimated surface NO 2 concentrations provide comprehensive information of NO 2 spatial distribution which is very useful for exposure estimation. We estimated the annual average NO 2 exposure for 2018, 2019 and 2020 is 15.53, 15.24 and 13.27 µ g/m 3 , respectively. While the annual average NO 2 concentration of 2018, 2019 and 2020 is only 12.79, 12.60 and 11.15 µ g/m 3 . In addition, we used the surface NO 2 data set to investigate the impacts of the coronavirus disease 2019 (COVID-19) pandemic on ambient NO 2 levels in Germany. In general, 10–30% lower surface NO 2 concentrations are observed in 2020 compared to 2018 and 2019, indicating the significant impacts of a series of restriction measures to reduce the spread of the virus. [ABSTRACT FROM AUTHOR]

In this paper, we propose a Stack Auto-encoder (SAE)-Driven and Semi-Supervised (SSL)-Based Deep Neural Network (DNN) to extract buildings from relatively low-cost satellite near infrared images. The novelty of our scheme is that we employ only an extremely small portion of labeled data for training the deep model which constitutes less than 0.08% of the total data. This way, we significantly reduce the manual effort needed to complete an annotation process, and thus the time required for creating a reliable labeled dataset. On the contrary, we apply novel semi-supervised techniques to estimate soft labels (targets) of the vast amount of existing unlabeled data and then we utilize these soft estimates to improve model training. Overall, four SSL schemes are employed, the Anchor Graph, the Safe Semi-Supervised Regression (SAFER), the Squared-loss Mutual Information Regularization (SMIR), and an equal importance Weighted Average of them (WeiAve). To retain only the most meaning information of the input data, labeled and unlabeled ones, we also employ a Stack Autoencoder (SAE) trained under an unsupervised manner. This way, we handle noise in the input signals, attributed to dimensionality redundancy, without sacrificing meaningful information. Experimental results on the benchmarked dataset of Vaihingen city in Germany indicate that our approach outperforms all state-of-the-art methods in the field using the same type of color orthoimages, though the fact that a limited dataset is utilized (10 times less data or better, compared to other approaches), while our performance is close to the one achieved by high expensive and much more precise input information like the one derived from Light Detection and Ranging (LiDAR) sensors. In addition, the proposed approach can be easily expanded to handle any number of classes, including buildings, vegetation, and ground. [ABSTRACT FROM AUTHOR]

Lidar remote sensing has proven to be a powerful tool for estimating ground elevation, canopy height, and additional vegetation parameters, which in turn are valuable information for the investigation of ecosystems. Spaceborne lidar systems, like the Global Ecosystem Dynamics Investigation (GEDI), can deliver these height estimates on a near global scale. This paper analyzes the accuracy of the first version of GEDI ground elevation and canopy height estimates in two study areas with temperate forests in the Free State of Thuringia, central Germany. Digital terrain and canopy height models derived from airborne laser scanning data are used as reference heights. The influence of various environmental and acquisition parameters (e.g., canopy cover, terrain slope, beam type) on GEDI height metrics is assessed. The results show a consistently high accuracy of GEDI ground elevation estimates under most conditions, except for areas with steep slopes. GEDI canopy height estimates are less accurate and show a bigger influence of some of the included parameters, specifically slope, vegetation height, and beam sensitivity. A number of relatively high outliers (around 9–13% of the measurements) is present in both ground elevation and canopy height estimates, reducing the estimation precision. Still, it can be concluded that GEDI height metrics show promising results and have potential to be used as a basis for further investigations. [ABSTRACT FROM AUTHOR]

The retention of structural elements such as habitat trees in forests managed for timber production is essential for fulfilling the objectives of biodiversity conservation. This paper seeks to predict tree-related microhabitats (TreMs) by close-range remote sensing parameters. TreMs, such as cavities or crown deadwood, are an established tool to quantify the suitability of habitat trees for biodiversity conservation. The aim to predict TreMs based on remote sensing (RS) parameters is supposed to assist a more objective and efficient selection of retention elements. The RS parameters were collected by the use of terrestrial laser scanning as well as unmanned aerial vehicles structure from motion point cloud generation to provide a 3D distribution of plant tissue. Data was recorded on 135 1-ha plots in Germany. Statistical models were used to test the influence of 28 RS predictors, which described TreM richness (R2: 0.31) and abundance (R2: 0.31) in moderate precision and described a deviance of 44% for the abundance and 38% for richness of TreMs. Our results indicate that multiple RS techniques can achieve moderate predictions of TreM occurrence. This method allows a more efficient and objective selection of retention elements such as habitat trees that are keystone features for biodiversity conservation, even if it cannot be considered a full replacement of TreM inventories due to the moderate statistical relationship at this stage. [ABSTRACT FROM AUTHOR]

In this paper we aim to show a proof-of-principle approach to detect and monitor weed management using glyphosate-based herbicides in agricultural practices. In a case study in Germany, we demonstrate the application of Sentinel-2 multispectral time-series data. Spectral broadband vegetation indices were analysed to observe vegetation traits and weed damage arising from herbicide-based management. The approach has been validated with stakeholder information about herbicide treatment using commercial products. As a result, broadband NDVI calculated from Sentinel-2 data showed explicit feedback after the glyphosate-based herbicide treatment. Vegetation damage could be detected after just two days following of glyphosate-based herbicide treatment. This trend was observed in three different application scenarios, i.e., during growing stage, before harvest and after harvest. The findings of the study demonstrate the feasibility of satellite based broadband NDVI data for the detection of glyphosate-based herbicide treatment and, e.g., the monitoring of latency to harvesting. The presented results can be used to implement monitoring concepts to provide the necessary transparency about weed treatment in agricultural practices and to support environmental monitoring. [ABSTRACT FROM AUTHOR]

Storms can cause significant damage to forest areas, affecting biodiversity and infrastructure and leading to economic loss. Thus, rapid detection and mapping of windthrows are crucially important for forest management. Recent advances in computer vision have led to highly-accurate image classification algorithms such as Convolutional Neural Network (CNN) architectures. In this study, we tested and implemented an algorithm based on CNNs in an ArcGIS environment for automatic detection and mapping of damaged areas. The algorithm was trained and tested on a forest area in Bavaria, Germany.. It is a based on a modified U-Net architecture that was optimized for the pixelwise classification of multispectral aerial remote sensing data. The neural network was trained on labeled damaged areas from after-storm aerial orthophotos of a ca. 109 k m 2 forest area with RGB and NIR bands and 0.2-m spatial resolution. Around 10 7 pixels of labeled data were used in the process. Once the network is trained, predictions on further datasets can be computed within seconds, depending on the size of the input raster and the computational power used. The overall accuracy on our test dataset was 92 % . During visual validation, labeling errors were found in the reference data that somewhat biased the results because the algorithm in some instance performed better than the human labeling procedure, while missing areas affected by shadows. Our results are very good in terms of precision, and the methods introduced in this paper have several additional advantages compared to traditional methods: CNNs automatically detect high- and low-level features in the data, leading to high classification accuracies, while only one after-storm image is needed in comparison to two images for approaches based on change detection. Furthermore, flight parameters do not affect the results in the same way as for approaches that require DSMs and DTMs as the classification is only based on the image data themselves, and errors occurring in the computation of DSMs and DTMs do not affect the results with respect to the z component. The integration into the ArcGIS Platform allows a streamlined workflow for forest management, as the results can be accessed by mobile devices in the field to allow for high-accuracy ground-truthing and additional mapping that can be synchronized back into the database. Our results and the provided automatic workflow highlight the potential of deep learning on high-resolution imagery and GIS for fast and efficient post-disaster damage assessment as a first step of disaster management. [ABSTRACT FROM AUTHOR]