Search

The molecular characteristics and rheological properties of three UHMWPE samples were investigated. The high-temperature GPC method was used for characterizing UHMWPE samples used. The interpretation of the measurement results was based on calibration using the PS standard and the approximation of the PS data by linear and cubic polynomials, as well as on the data for linear PE. The assessment of the average MW and MWD depends on the choice of calibration method, so that different methods give different results. Only the results obtained using PS with cubic approximation are close to the characteristics offered by the manufacturer. It was also shown that the obtained MW characteristics depend on the dissolution time. The reason for this may be the presence of any processing-aid compounds or destruction of macromolecules. Measurements of the rheological properties were performed in creep modes for a wide range of shear stresses and harmonic oscillations. It was shown that even at 210 °C, UHMWPE does not flow, and the observed irreversible deformations are due to the plasticity of the polymer, i.e., UHMWPE is in an elastic–plastic state. The ultimate plastic deformations drop sharply with increasing MW of the polymer. The plasticity modulus for the highest molecular weight UHMWPE samples does not depend on stress. Measurements of viscoelastic characteristics confirmed that the terminal region of viscous flow cannot be reached under any conditions. Increasing the duration of holding the polymer at high temperature leads not to flow, but to the destruction of macromolecules. [ABSTRACT FROM AUTHOR]

Ultra-high-molecular-weight polyethylene (UHMWPE) is often considered an ideal reinforcing material due to its extraordinary characteristics like high abrasion resistance, excellent toughness, and chemical stability. However, the poor surface properties have significantly hindered the progress of UHMWPE with high performance. This review is intended to introduce the physicochemical mechanisms of UHMWPE interfacial property modification. Therefore, this review provides a concise overview of the progress in diverse surface modification techniques for UHMWPE and their strengths and limitations as polymer reinforcement materials. Lastly, an overview of the potential and challenges of each surface modification has been summarized. [ABSTRACT FROM AUTHOR]

As the risk of social security increases, it is crucial to develop flexible protective materials that combine flexibility with high protective performance. Ultra-high-molecular-weight polyethylene (UHMWPE) was selected as the raw material, and four types of flat-knitting cut-resistant fabrics were ultimately designed and prepared from a three-dimensional longitudinal dimension and concave–convex array structure based on rib knitting. A series of experiments must be conducted on fabrics in order to study the law of protection performance of different structural fabrics. They were thus subjected to comprehensive evaluation and theoretical analysis of cut resistance. The results demonstrate that the four structural fabrics exhibited resilience in abrasion tests, withstanding over 100,000 cycles without failure. A weighting algorithm was employed to determine the comprehensive cutting resistance of the S1, S2, S3, and S4 structural fabrics, resulting in values of 1939.9 gf, 2298.6 gf, 2577.1 gf, and 2822.2 gf, respectively. Therefore, S1 reached class A4, which is sufficient to address a medium cut hazard. Similarly, S2, S3, and S4 reached class A5, which is adequate to address a high cut hazard. The obtained fitting equation, with uniform yarn fineness T as the dependent variable, demonstrates that the cut resistance improved as the concave–convex density level increased. [ABSTRACT FROM AUTHOR]

In order to withstand high-temperature environments, ultra-high molecular weight polyethylene (UHMWPE) fibers with cooling properties are being increasingly used in personal thermal management textiles during the summer. However, there is relatively little research on its combination with knitting. In this paper, we combine UHMWPE fiber and knitting structure to investigate the impact of varying UHMWPE fiber content and different knitting structures on the heat and humidity comfort as well as the cooling properties of fabrics. For this purpose, five kinds of different proportions of UHMWPE and polyamide yarn preparation, as well as five kinds of knitted tissue structures based on woven tissue were designed to weave 25 knitted fabrics. The air permeability, moisture permeability, moisture absorption and humidity conduction, thermal property, and contact cool feeling property of the fabrics were tested. Then, orthogonal analysis and correlation analysis were used to statistically evaluate the properties of the fabrics statistically. The results show that as the UHMWPE content increases, the air permeability, heat conductivity, and contact cool feeling property of the fabrics improve. The moisture permeability, moisture absorption and humidity conductivity of fabrics containing UHMWPE are superior to those containing only polyamide. The air permeability, moisture permeability, and thermal conductivity of the fabrics formed by the tuck plating organization are superior to those of the flat needle plating and float wire plating organization. The fabric formed by 2 separate 2 float wire organization has the best moisture absorption, humidity conduction, contact cool feeling property. [ABSTRACT FROM AUTHOR]

We have evaluated the effectiveness of compatibilizers in blends and composites produced using a solvent manufacturing process. The compatibilizers were two different types of polyethylene (linear low-density and high-density) grafted with maleic anhydride (MAH) and a highly functionalized, epoxy-based compatibilizer with the tradename Joncryl. The selected material combinations were an ultra-high-molecular-weight polyethylene (UHMWPE) with MAH-based materials as compatibilizers and a polyphenylene sulfide plus polytetrafluoroethylene (PPS-PTFE) polymer blend with an epoxy-based compatibilizer. The findings revealed that while the compatibilizers consistently enhanced the properties, such as the impact strength and hardness of PPS-based compositions, their utility is constrained to less complex compositions, such as fibrous-reinforced PPS or PPS-PTFE polymer blends. For fibrous-reinforced PPS-PTFE composites, the improvement in performance does not justify the presence of compatibilizers. In contrast, for UHMWPE compositions, compatibilizers demonstrated negligible or even detrimental effects, particularly in reinforced UHMWPE. Overall, the epoxy-based compatibilizer Joncryl stands out as the only effective option for enhancing mechanical performance. Thermal and chemical characterization indicated that the compatibilizers function as chain extenders and enhance the fiber–matrix interface in PPS-based compositions, while they remain inactive in UHMWPE-based compositions. Ultimately, the incompatibility of the compatibilizers with certain aspects of the manufacturing method and the inconsistent integration with the polymer are the main reasons for their ineffectiveness in UHMWPE compositions. [ABSTRACT FROM AUTHOR]

At present, the challenging issue of the compatibility between stab resistance and flexibility of materials frequently appears. Thus, this study proposes a novel method to enhance the comprehensive performance of the material matrix with stab resistance. Based on the stab-resistant mechanism analysis of the textile matrix, the influence of four factors on the performance of ultra-high molecular weight polyethylene (UHMWPE) knitted fabric was discussed. And, the optimal process conditions of material for achieving high stab resistance and high flexibility were obtained by the response surface method. A series of experiments proved that among all factors, the fabric structure had the greatest influence on the flexible stab-resistant knitted material. Following that, the thickness of the yarn also plays a significant role. Under the optimal process conditions, the stab peak force of the knitted material was promoted to 52.450 N, and the flexibility was enhanced to 93.6%. Meanwhile, through comparison with products that have undergone the same treatment, there was little difference in stab resistance but significantly improved flexibility. It achieves the initial stab resistance and comfortable wearing softness of the fabric through process optimization. This improvement in overall performance of the textile matrix enables further enhancement treatments. [ABSTRACT FROM AUTHOR]

Polymer composites are a class of material that are gaining a lot of attention in demanding tribological applications due to the ability of manipulating their performance by changing various factors, such as processing parameters, types of fillers, and operational parameters. Hence, a number of samples under different conditions need to be repeatedly produced and tested in order to satisfy the requirements of an application. However, with the advent of a new field of triboinformatics, which is a scientific discipline involving computer technology to collect, store, analyze, and evaluate tribological properties, we presently have access to a variety of high-end tools, such as various machine learning (ML) techniques, which can significantly aid in efficiently gauging the polymer's characteristics without the need to invest time and money in a physical experimentation. The development of an accurate model specifically for predicting the properties of the composite would not only cheapen the process of product testing, but also bolster the production rates of a very strong polymer combination. Hence, in the current study, the performance of five different machine learning (ML) techniques is evaluated for accurately predicting the tribological properties of ultrahigh molecular-weight polyethylene (UHMWPE) polymer composites reinforced with silicon carbide (SiC) nanoparticles. Three input parameters, namely, the applied pressure, holding time, and the concentration of SiCs, are considered with the specific wear rate (SWR) and coefficient of friction (COF) as the two output parameters. The five techniques used are support vector machines (SVMs), decision trees (DTs), random forests (RFs), k-nearest neighbors (KNNs), and artificial neural networks (ANNs). Three evaluation statistical metrics, namely, the coefficient of determination (R2-value), mean absolute error (MAE), and root mean square error (RMSE), are used to evaluate and compare the performances of the different ML techniques. Based upon the experimental dataset, the SVM technique was observed to yield the lowest error rates—with the RMSE being 2.09 × 10−4 and MAE being 2 × 10−4 for COF and for SWR, an RMSE of 2 × 10−4 and MAE of 1.6 × 10−4 were obtained—and highest R2-values of 0.9999 for COF and 0.9998 for SWR. The observed performance metrics shows the SVM as the most reliable technique in predicting the tribological properties—with an accuracy of 99.99% for COF and 99.98% for SWR—of the polymer composites. [ABSTRACT FROM AUTHOR]

Ultrahigh-molecular-weight polyethylene (UHMWPE) is used in the defence industry mainly owing to its properties, such as excellent dimensional stability, excellent ballistic performance, and light weight. Although UHMWPE laminates are generally studied under impact loads, it is crucial to understand better the optimal machining conditions for assembling auxiliary structures in combat helmets or armour. This work analyses the machinability of UHMWPE laminates by drilling. The workpiece material has been manufactured through hot-pressing technology and subjected to drilling tests. High-speed steel (HSS) twist drills with two different point angles and a brad and spur drill that is 6 mm in diameter have been used for this study. Cutting forces, failure, and main damage modes are analysed, making it possible to extract relevant information for the industry. The main conclusion is that the drill with a smaller point angle has a better cutting force performance and less delamination at the exit zone (5.4 mm at a 60 m/min cutting speed and a 0.05 mm/rev feed) in the samples. This value represents a 46% improvement over the best result obtained in terms of delamination at the exit when using the tool with the larger point angle. However, the brad and spur drill revealed a post-drilling appearance with high fuzzing and delamination. [ABSTRACT FROM AUTHOR]

This work presents a comprehensive investigation of an experimental study conducted on ultra-high molecular weight polyethylene (UHMWPE) sheets using single point incremental forming (SPIF). The analysis is performed within a previously established research framework to evaluate formability and failure characteristics, including necking and fracture, in both conventional Nakajima tests and incremental sheet forming specimens. The experimental design of the SPIF tests incorporates process parameters such as spindle speed and step down to assess their impact on the formability of the material and the corresponding failure modes. The results indicate that a higher step down value has a positive effect on formability in the SPIF context. The study has identified the tool trajectory in SPIF as the primary influencing factor in the twisting failure mode. Implementing a bidirectional tool trajectory effectively reduced instances of twisting. Additionally, this work explores a medical case study that examines the manufacturing of a polyethylene liner device for a total hip replacement. This investigation critically analyses the manufacturing of plastic liner using SPIF, focusing on its formability and the elastic recovery exhibited by the material. [ABSTRACT FROM AUTHOR]

Poly(p-phenylene terephthalamide) (PPTA) and ultra-high-molecular-weight polyethylene (UHMWPE) are high-performance polymer materials largely used for body armor applications. Although composite structures from a combination of PPTA and UHMWPE have been created and described in the literature, the manufacture of layered composites from PPTA fabrics and UHMWPE films with UHMWPE film as an adhesive layer has not been reported. Such a new design can provide the obvious advantage of simple manufacturing technology. In this study, for the first time, we prepared PPTA fabrics/UHMWPE films laminate panels using plasma treatment and hot-pressing and examined their ballistic performance. Ballistic testing results indicated that samples with moderate interlayer adhesion between PPTA and UHMWPE layers exhibited enhanced performance. A further increase in interlayer adhesion showed a reverse effect. This finding implies that optimization of interface adhesion is essential to achieve maximum impact energy absorption through the delamination process. In addition, it was found that the stacking sequence of the PPTA and UHMWPE layers affected ballistic performance. Samples with PPTA as the outermost layer performed better than those with UHMWPE as the outermost layer. Furthermore, microscopy of the tested laminate samples showed that PPTA fibers exhibited shear cutting failure on the entrance side and tensile failure on the exit side of the panel. UHMWPE films exhibited brittle failure and thermal damage at high compression strain rate on the entrance side and tensile fracture on the exit side. For the first time, findings from this study reported in-field bullet testing results of PPTA/UHMWPE composite panels, which can provide important insights for designing, fabricating, and failure analysis of such composite structures for body armors. [ABSTRACT FROM AUTHOR]

Melts of ultrahigh molecular weight polyethylene (UHMWPE) entangled significantly, suffering processing difficulty. In this work, we prepared partially disentangled UHMWPE by freeze-extracting, exploring the corresponding enchantment of chain mobility. Fully refocused 1H free induction decay (FID) was used to capture the difference in chain segmental mobility during the melting of UHMWPE with different degrees of entanglement by low-field solid-state NMR. The longer the polyethylene (PE) chain is in a less-entangled state, the harder the process of merging into mobile parts after detaching from crystalline lamella during melting. 1H double quantum (DQ) NMR was further used to obtain information caused by residual dipolar interaction. Before melting, the DQ peak appeared earlier in intramolecular-nucleated PE than in intermolecular-nucleated PE because of the strong constraints of crystals in the former one. During melting, less-entangled UHMWPE could keep disentangled while less-entangled high density polyethylene (HDPE) could not. Unfortunately, no noticeable difference was found in DQ experiments between PE melts with different degrees of entanglement after melting. It was ascribed to the small contribution of entanglements compared with total residual dipolar interaction in melts. Overall, less-entangled UHMWPE could reserve its disentangled state around the melting point long enough to achieve a better way of processing. [ABSTRACT FROM AUTHOR]

Rubber products generally need to have high resistance to abrasion, tear, and cutting. Filling short fiber with strong mechanical properties and forming a net in the rubber matrix is a good method to realize the above aims. In this article, ultra-high molecular weight polyethylene (UHMWPE) short fibers with a diameter of 20 μm and a length of 2 cm were filled into natural rubber (NR) to improve the tear strength of the NR. The influence of the short fiber mass fraction and vulcanization conditions on the mechanical properties of the composites were investigated. The results show that the milling process and vulcanization conditions are key factors in enhancing tear resistance performance. Double-roll milling and vulcanization at 143 °C for 40 min result in strong interfacial adhesion between the UHMWPE short fibers and the NR. The addition of 2 phr of UHMWPE fiber increases the tear strength of the composite material by up to 150.2% (from 17.1 kN/m to 42.8 kN/m) while also providing excellent comprehensive performance. Scanning electron microscope (SEM) imaging confirmed that the UHMWPE short fibers are dispersed in the NR matrix homogeneously, and the interface is close and compact. As a control experiment, UHMWPE resin powder was directly filled into the NR, and then the composite was vulcanized using the same process as that used for the NR/UHMWPE short fiber composite. The results show that the mechanical strength of the NR/resin powder composite exhibits minor improvement compared with NR. As there is no complicated surface modification of the UHMWPE fiber, the results reported may be helpful in improving the tear resistance of the industrially prepared rubber conveyor belts. [ABSTRACT FROM AUTHOR]

Thin sheets of ultra-high molecular weight polyethylene (UHMWPE), both in pristine form and containing carbon nanotubes (CNTs) or Fe2O3 nanoparticles (NPs) at different concentrations, were prepared. The CNT and Fe2O3 NP weight percentages used ranged from 0.01% to 1%. The presence of CNTs and Fe2O3 NPs in UHMWPE was confirmed by transmission and scanning electron microscopy and by energy dispersive X-ray spectroscopy analysis (EDS). The effects of the embedded nanostructures on the UHMWPE samples were studied using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy and UV–Vis absorption spectroscopy. The ATR-FTIR spectra show the characteristic features of the UHMWPE, CNTs, and Fe2O3. Concerning the optical properties, regardless of the type of embedded nanostructures, an increase in the optical absorption was observed. The allowed direct optical energy gap value was determined from the optical absorption spectra: in both cases, it decreases with increasing CNT or Fe2O3 NP concentrations. The obtained results will be presented and discussed. [ABSTRACT FROM AUTHOR]

Preparing high-strength polymeric materials using an orientation drawing process is considered one of the most urgent topics in the modern world. Graphene nanoplates/polyaniline (GNP/PANI) were added to the commercial grade UHMWPE (GUR 4120) matrix as a filler with antifriction properties. The effect of GNP/PANI addition on the structure, the orientation process, the void formation (cavitation), the mechanical, and tribological properties was studied using differential scanning calorimetry (DSC), dynamical mechanical analysis (DMA), and scanning electron microscopy (SEM). The paper's findings indicated an increase in the cavitation effect of 120–320% after the addition of GNP/PANI to the UHMWPE polymer matrix. This increase, during the process of the oriented films' thermal orientation hardening, led, in turn, to a decrease in the tensile strength during the process of the oriented films' thermal orientation hardening. Furthermore, the decrease in the coefficient of friction in the best samples of oriented UHMWPE films was two times greater, and the increase in wear resistance was more than an order of magnitude. This process was part of the orientation hardening process for the UHMWPE films containing PE-wax as an intermolecular lubricant, as well as the presence of GNP/PANI in the material, which have a high resistance to abrasive wear. [ABSTRACT FROM AUTHOR]

Ultra-high-molecular-weight polyethylene (UHMWPE) matrices containing low-density polyethylene (LDPE), hydroxyapatite (HAp) as filler, and rosemary extract (RM) as stabilizer were investigated for their qualification for long-term applications. The significant contributions of the blend components were analyzed, and variations in mechanical properties, oxidation strength, thermal behavior, crystallinity, and wettability were discussed. SEM images of microstructural peculiarities completed the introspective survey. The stability improvement due to the presence of both additives was an increase in the total degradation period of 67% in comparison with an unmodified HDPE/UHMWPE blend when the materials were subjected to a 50 kGy γ-dose. There was growth in activation energies from 121 kJ mol−1 to 139 kJ mol−1 when HAp and rosemary extract delayed oxidation. The exposure of samples to the action of γ-rays was found to be a proper procedure for accomplishing accelerated oxidative degradation. The presence of rosemary extract and HAp powder significantly increased the thermal and oxidation resistances. The calculation of material lifetimes at various temperatures provided meaningful information on the wearability and integrity of the inspected composites. [ABSTRACT FROM AUTHOR]

This contribution lays the foundation for the European database of explanted UHMWPE liners from total joint replacements. Three EU countries (Czech Republic, Italy and Spain) have joined their datasets containing anonymized patient data (such as age and BMI), manufacturer data (such as information on UHMWPE crosslinking, thermal treatment and sterilization), orthopedic evaluation (such as total duration of the implant in vivo and reasons for its revision) and material characterization (such as oxidative degradation and micromechanical properties). The joined database contains more than 500 entries, exhibiting gradual growth, and it is beginning to show interesting trends, which are discussed in our contribution, including (i) strong correlations between UHMWPE oxidative degradation, degree of crystallinity and microhardness; (ii) statistically significant differences between UHMWPE liners with different types of sterilization; (iii) realistic correlations between the extent of oxidative degradation and the observed reasons for total joint replacement failures. Our final objective and task for the future is to continuously expand the database, involving researchers from other European countries, in order to create a robust tool that will contribute to the better understanding of structure–properties–performance relationships in the field of arthroplasty implants. [ABSTRACT FROM AUTHOR]

Ultra-high molecular weight polyethylene (UHMWPE)/high-density polyethylene (HDPE) blend with lower viscosity is more suitable for melt spinning compared to pure UHMWPE; however, the mechanical property of the blend fiber is hard to dramatically improve (the maximum tensile strength of 998.27 MPa). Herein, different content modified-nano-SiO2 is incorporated to UHMWPE/HDPE blend fiber. After adding 0.5 wt% nano-SiO2, the tensile strength and initial modulus of UHMWPE/HDPE/nano-SiO2 fiber are increased to 1211 MPa and 12.81 GPa, respectively, 21.57% and 43.32% higher than that of UHMWPE/HDPE fiber. Meanwhile, the influence of the nano-SiO2 content on the performance for as-spun filament and fiber are emphatically analyzed. The crystallinity and molecular chain orientation of as-spun filament reduces with the addition of nano-SiO2. On the contrary, for fiber, the addition of nano-SiO2 promoted the crystallinity, molecular chain orientation and grain refinement more obvious at a lower content. Furthermore, the possible action mechanism of nano-SiO2 in the as-spun filament extrusion and fiber hot drawing stage is explained. [ABSTRACT FROM AUTHOR]

The reported study was devoted to the investigation of viscoelastic behavior for solid and porous ultra-high molecular weight polyethylene (UHMWPE) under compression. The obtained experimental stress curves were interpreted using a two-term Prony series to represent the superposition of two coexisting activation processes corresponding to long molecular (~160 s) and short structural (~20 s) time scales, respectively, leading to good statistical correlation with the observations. In the case of porous polymer, the internal strain redistribution during relaxation was quantified using digital image correlation (DIC) analysis. The strongly inhomogeneous deformation of the porous polymer was found not to affect the relaxation times. To illustrate the possibility of generalizing the results to three dimensions, X-ray tomography was used to examine the porous structure relaxation at the macro- and micro-scale levels. DIC analysis revealed positive correlation between the applied force and relative density. The apparent stiffness variation for UHMWPE foams with mixed open and closed cells was described using a newly proposed three-term expression. Furthermore, in situ tensile loading and X-ray scattering study was applied for isotropic solid UHMWPE specimens to investigate the evolution of internal structure and orientation during drawing and stress relaxation in another loading mode. [ABSTRACT FROM AUTHOR]

One of the main research work in the field of polymeric materials was, is and always will be the improvement of their mechanical properties. Comprehensive structural studies of UHMWPE reactor powder, the features of its dissolution and the formation of a gel-state, as well as UHMWPE films oriented up to various draw ratios, were carried out using scanning electron microscopy, differential scanning calorimetry, and X-ray diffraction. For comparison, decalin and vaseline oil were chosen as solvents. The mechanical properties of oriented UHMWPE films were also studied. In the process of orientation drawing, basing on the developed structural-kinetic principles of strengthening for highly oriented speciments gel-cast from UHMWPE powders, the average values of tensile strength of 4.7 GPa (about 6% of the samples had strength values up to 6.0 GPa) and an Young's modulus of 170 GPa (about 6% of the samples had Young's modulus values of 200 GPa). These values are among the highest according to the world scientific literature. A significant increase in the mechanical characteristics of highly oriented UHMWPE films was achieved using experimentally confirmed scientific approaches to revealing the structure-property relationship at each stage of the gel process. [ABSTRACT FROM AUTHOR]

To modify its characteristics, expand its applicability, and, in some cases, its processability, new blends using ultra-high-molecular-weight polyethylene (UHMWPE) have been developed. In this study, three different formulations of linear low-density polyethylene (LLDPE) and UHMWPE blends were prepared with 15, 30, and 45% (% w/w) UHMWPE in the LLDPE matrix. All mixtures were prepared by hot pressing and were immersed in water for one hour afterwards at a controlled temperature of 90 °C to relieve the internal stresses that developed during the forming process. The thermal characterization showed that the blends showed endothermic peaks with different melting temperatures, which may be the result of co-crystallization without mixing between the polymers during the forming process. The mechanical characteristics presented are typical of a ductile material, but with the increase in the percentage of UHMWPE, there was a decrease in the ductility of the blends, as the elongation at rupture of the blends was higher than that of the pure components. The morphologies observed by SEM indicate that there were two phases in the blends. This is the result of the system's immiscibility due to the mode of preparation of the blends, wherein the two polymers may not have mixed intimately, confirming the results found with the thermal analyses. [ABSTRACT FROM AUTHOR]

Activated Carbon (AC) is widely available at a relatively low cost, has a high porosity and is commonly used as a filter material for a range of applications. However, it is a brittle and friable material. Ultra-High Molecular Weight Polyethylene (UHMWPE) polymer is a tough engineering plastic that has been used as a binder. The traditional method used in manufacturing AC/UHMWPE filters involves compressing AC/UHMWPE composite powder during heating in a mould. This process compresses the particles together and the materials undergo sintering. This process results in a low pore interconnectivity, which has a considerable impact on the filter's efficiency. Selective Laser Sintering is a laser powder bed fusion additive manufacturing technique for polymers. This has a number of advantages compared to the conventional technique and produces a porous structure with improved filtration efficiency. We propose that this is due to the greater pore interconnectivity. In this work, AC/UHMWPE powdered composites were prepared with different AC and UHMWPE ratios. The structure and properties of the AC/UHMWPE composite were investigated and characterised to assess their suitability for selective laser sintering. Particle size and morphology analysis were conducted, as well as density measurements, powder flow, thermal analysis, and crystallinity measurements. The results reveal that the addition of AC improves the UHMWPE flow. The thermal analysis results show that the intrinsic thermal properties of UHMWPE powder are not significantly affected by the introduction of activated carbon. However, thermal gravimetric analysis revealed that the onset of mass loss is considerably shifted (20 °C) to higher temperatures for the AC/UHMWPE composites, which is favourable for laser sintering. Additionally, the change in the composition ratio of untreated composite does not have a significant effect on the degree of crystallinity. Laser-sintered AC/UHMWPE parts were successfully manufactured using a commercial laser-sintering machine. [ABSTRACT FROM AUTHOR]

Bulk oriented films based on ultrahigh molecular weight polyethylene (UHMWPE) with a drawing ratio of 35 were prepared by using a low solvent concentration. Bulk oriented films were filled with fluorinated multi-walled carbon nanotubes (FMWCNTs). The structure of bulk oriented films on UHMWPE, which were manufactured at different stages of orientation, was investigated by scanning electron microscope (SEM) and differential scanning calorimetry (DSC). The addition of FMWCNTs at a concentration of 0.05 wt % in bulk oriented UHMWPE films led to an increase in the tensile strength by 10% (up to 1020 ± 23 MPa) compared to unfilled oriented films. However, the addition of FMWCNTs at a concentration of more than 0.5 wt % led to a decrease in tensile strength due to excessive accumulation of nanotubes and hindering of self-diffusion of UHMWPE macromolecules. The multiple increase in tensile strength, doubling the hardness, the formation of fibrillar structure, and the presence of carbon nanotubes led to a significant increase in tribological properties in bulk oriented films. Bulk oriented UHMWPE/1% FMWCNT films can be operated at a maximum contact pressure that is 18 times higher and exhibit a specific wear rate more than an order of magnitude and less than the traditional UHMWPE of isotropic structure. Bulk oriented UHMWPE/1% FMWCNT films have an extremely low dry coefficient of friction (COF) of 0.075 at a contact pressure of 31 MPa. The developed bulk oriented films can be used for manufacturing frictional surfaces for sliding bearings, or for acetabular cups for knee and hip endoprostheses. [ABSTRACT FROM AUTHOR]

Ultra-high molecular weight polyethylene (UHMWPE) and high-density polyethylene (HDPE) blend fibers with the highest tensile strength of 1.13 GPa were prepared by a melt spinning process. The mechanical behavior and crystal structure of the as-spun filaments and fibers were studied by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), X-ray diffraction (XRD), sound velocity orientation testing, and tensile testing. The orientation degree, crystallinity, tensile strength, and initial modulus of the fibers increased with the increasing of the draw ratios. The grain size was shortened in the radial direction and elongated in the axial direction. The results suggested that the improvement of the tensile strength and initial modulus was a result of the compact crystal structure formed by slender grains composed of highly oriented molecular chains. Blending with HDPE could improve the formation of a slender and compact crystal structure, and the tensile strength and initial modulus of the blend fibers were higher. [ABSTRACT FROM AUTHOR]

Ultra-high molecular weight polyethylene (UHMWPE) is widely used in artificial joints in the replacement of knee, hip and shoulder that has been impaired as a result of arthritis or other degenerative joint diseases. The UHMWPE made plastic cup is placed in the joint socket in contact with a metal or ceramic ball affixed to a metal stem. Effective reinforcement of multi-walled carbon nanotubes (MWCNTs) in UHMWPE results in improved mechanical and tribological properties. The hydrophobic nature of the nanocomposites surface results in lesser contact with biological fluids during the physiological interaction. In this project, we investigate the UHMWPE/MWCNTs nanocomposites reinforced with MWCNTs at different concentrations. The samples were treated with cold argon plasma at different exposure times. The water contact angles for 60 min plasma-treated nanocomposites with 0.0, 0.5, 1.0, 1.5, and 2.0 wt % MWCNTs were found to be 55.65°, 52.51°, 48.01°, 43.72°, and 37.18° respectively. Increasing the treatment time of nanocomposites has shown transformation from a hydrophobic to a hydrophilic nature due to carboxyl groups being bonded on the surface for treated nanocomposites. Wear analysis was performed under dry, and also under biological lubrication, conditions of all treated samples. The wear factor of untreated pure UHMWPE sample was reduced by 68% and 80%, under dry and lubricated conditions, respectively, as compared to 2 wt % 60 min-treated sample. The kinetic friction co-efficient was also noted under both conditions. The hardness of nanocomposites increased with both MWCNTs loading and plasma treatment time. Similarly, the surface roughness of the nanocomposites was reduced. [ABSTRACT FROM AUTHOR]

The potential of quantifying the variations in IR active bands was explored while using the chemometric analysis of FTIR spectra for selecting orthopedic biomaterial of industrial scale i.e., ultra-high molecular weight PE (UHMWPE). The nano composites UHMWPE with multi-walled carbon nano-tubes (MWCNTs) and Mg-silicate were prepared and irradiated with 25 kGy and 50 kGy of gamma dose. Principal component analysis (PCA) revealed that first three principal components (PCs) are responsible for explaining the >99% of variance in FTIR data of UHMWPE on addition of fillers and/or irradiation. The factor loadings plots revealed that PC-1 was responsible for explaining the variance in polyethylene characteristics bands and the IR active region induced by fillers i.e., 440 cm−1, 456 cm−1, from 900–1200 cm−1, 1210 cm−1, 1596 cm−1, PC-2 was responsible for explaining the variance in spectra due to radiation-induced oxidation and cross linking, while the PC-3 is responsible for explaining the variance induced because of IR active bands of MWCNTs. Hierarchy cluster analysis (HCA) was employed to classify the samples into four clusters with respect to similarity in their IR active bands which is further confirmed by PCA. According to multi attribute analysis with PCA and HCA, 65 kGy irradiated sample is optimum choice from the existing alternatives in the group of irradiated pristine UHMWPE, UHMWPE/Mg-silicate irradiated with 25 kGy of gamma dose was the optimum choice for UHWMPE/Mg-silicate nano composites, and UHMWPE/γMWCNTs composites containing 1.0% dof γ MWCNTs for UHMWPE/MWCNTs nanocomposites, respectively. The results show the effectiveness of quantifying the variance for decision as far as optimization of biomaterials in orthopedic industrial applications is concerned. [ABSTRACT FROM AUTHOR]

The selection of suitable composite material for high-strength industrial applications, from the list of available alternatives, is a tedious task as it requires an optimized structural performance-based solution. This study aimed to optimize the concentration of fillers, i.e., vinyl tri-ethoxy silane and absorbed gamma-dose, to enhance the properties of an industrial scale polymer, i.e., ultra-high molecular weight polyethylene (UHMWPE). The UHMWPE hybrids, in addition to silane, were treated with (30, 65, and 100 kGy) gamma dose and then tested for ten application-specific structural and performance attributes. The relative importance of attributes based on an 11-point fuzzy conversation was used for establishing the material assessment graph and corresponding adjacency matrix. Afterwards, the normalized values of attributes were used to establish the decision matrix for each alternative. The normalization was performed after the identification of high obligatory valued (HOV) and low obligatory valued (LOV) attributes. After this, suitability index values (SIVs) were calculated for ranking the hybrids that revealed hybrids 65 kGy irradiated the hybrid as the best choice and ranked as first among the existing alternatives. The major responsible factors were higher oxidation strength, a dense cross-linking network, and elongation at break. The values of the aforementioned factors for 65 kGy irradiated hybrids were 0.24, 91, and 360 MPa, respectively, as opposed to 0.54, 75, and 324 MPa for 100 kGy irradiated hybrids, thus placing the latter in second place regarding higher values of Yield Strength and Young Modulus. Finally, it is believed that the reported results and proposed model in this study will improve preoperative planning as far as considering these hybrids for high-strength industrial applications including total joint arthroplasty, textile-machinery pickers, dump trucks lining ships, and harbors bumpers and sliding, etc. [ABSTRACT FROM AUTHOR]

This work reports on the simulated neutron and self-emitted gamma attenuation of ultra-high-molecular-weight polyethylene (UHMWPE) composites containing varying Sm2O3 contents in the range 0–50 wt.%, using a simulation code, namely MCNP-PHITS. The neutron energy investigated was 0.025 eV (thermal neutrons), and the gamma energies were 0.334, 0.712, and 0.737 MeV. The results indicated that the abilities to attenuate thermal neutrons and gamma rays were noticeably enhanced with the addition of Sm2O3, as seen by the increases in µm and µ, and the decrease in HVL. By comparing the simulated neutron-shielding results from this work with those from a commercial 5%-borated PE, the recommended Sm2O3 content that attenuated thermal neutrons with equal efficiency to the commercial product was 11–13 wt.%. Furthermore, to practically improve surface compatibility between Sm2O3 and the UHMWPE matrix and, subsequently, the overall wear/mechanical properties of the composites, a silane coupling agent (KBE903) was used to treat the surfaces of Sm2O3 particles prior to the preparation of the Sm2O3/UHMWPE composites. The experimental results showed that the treatment of Sm2O3 particles with 5–10 pph KBE903 led to greater enhancements in the wear resistance and mechanical properties of the 25 wt.% Sm2O3/UHMWPE composites, evidenced by lower specific wear rates and lower coefficients of friction, as well as higher tensile strength, elongation at break, and surface hardness, compared to those without surface treatment and those treated with 20 pph KBE903. In conclusion, the overall results suggested that the addition of Sm2O3 in the UHMWPE composites enhanced abilities to attenuate not only thermal neutrons but also gamma rays emitted after the neutron absorption by Sm, while the silane surface treatment of Sm2O3, using KBE903, considerably improved the processability, wear resistance, and strength of the composites. [ABSTRACT FROM AUTHOR]

Peroxide has been considered a chemical agent that can be used to tune the properties of polymeric materials. This research evaluated the influence of different concentrations of dialkyl peroxides on the mechanical, thermal, and morphological properties of linear low-density polyethylene (LLDPE) and ultra-high molecular weight polyethylene (UHMWPE). The neat polymer, as well as those with the addition of 1% and 2% by mass of dialkyl peroxides, were subjected to compression molding and immersion in water for 1 h, under controlled temperatures of 90 °C. The values of the gel content found in the samples indicated that the addition of peroxide to the LLDPE and to the UHMWPE promoted the formation of a reticulated network. The structure obtained by the crosslinking led to less reorganization of the chains during the crystallization process, resulting in the formation of imperfect crystals and, consequently, in the reduction in melting temperatures, crystallization and enthalpy. The mechanical properties were altered with the presence of the crosslinker. The polymers presented had predominant characteristics of a ductile material, with the occurrence of crazing with an increased peroxide content. [ABSTRACT FROM AUTHOR]

(1) Background: This study investigated the miscibility of carbon-based fillers within industrial scale polymers for the preparation of superior quality polymer composites. It focuses on finding the light distribution in gamma irradiated ultra-high molecular weight polyethylene (UHMWPE). (2) Methods: The Kubleka–Munk model (KMM) was used to extract the optical properties, i.e., absorption coefficients (μa) and scattering coefficients (μs). Samples amounting to 30 kGy and 100 kGy of irradiated (in the open air) UHMWPE from 630 nm to 800 nm were used for this purpose. Moreover, theoretical validation of experimental results was performed while using extracted optical properties as inputs for the Monte Carlo model of light transport (MCML) code. (3) Conclusions: The investigations revealed that there was a significant decrease in absorption and scattering coefficient (μa & μs) values with irradiation, and 30 kGy irradiated samples suffered more compared to 100 kGy irradiated samples. Furthermore, the simulation of light transport for 800 nm showed an increase in penetration depth for UHMWPE after gamma irradiation. The decrease in dimensionless transport albedo   μ s (μ a + μ s) from 0.95 to 0.93 was considered responsible for this increase in photon absorption per unit area with irradiation. The report results are of particular importance when considering the light radiation (from 600 nm to 899 nm) for polyethylene modification and/or stabilization via enhancing the polyethylene chain mobility. [ABSTRACT FROM AUTHOR]

Here, nanocomposites of high-molecular-weight polyethylene (HMWPE) and HMWPE-UHMWPE (80/20 wt.%) containing a low amount of multilayer graphene oxide (mGO) (≤0.1 wt.%) were produced via twin-screw extrusion to produce materials with a higher tribological performance than UHMWPE. Due to the high viscosity of both polymers, the nanocomposites presented a significant concentration of agglomerates. However, the mechanical (tensile) and tribological (volumetric loss) performances of the nanocomposites were superior to those of UHMWPE. The morphology of the nanocomposites was investigated using differential scanning calorimetry (DSC), microtomography, and transmission electron microscopy (TEM). The explanation for these results is based on the superlubricity phenomenon of mGO agglomerates. It was also shown that the well-exfoliated mGO also contained in the nanocomposite was of fundamental importance as a mechanical reinforcement for the polymer. Even with a high concentration of agglomerates, the nanocomposites displayed tribological properties superior to UHMWPE's (wear resistance up to 27% higher and friction coefficient up to 57% lower). Therefore, this manuscript brings a new exception to the rule, showing that agglomerates can act in a beneficial way to the mechanical properties of polymers, as long as the superlubricity phenomenon is present in the agglomerates contained in the polymer. [ABSTRACT FROM AUTHOR]

Diamond-like carbon (DLC) coatings have the potential to reduce implant wear and thus to contribute to avoiding premature failure and increase service life of total knee replacements (TKAs). This two-part study addresses the development of such coatings for ultrahigh molecular weight polyethylene (UHMWPE) tibial inlays as well as cobalt–chromium–molybdenum (CoCr) and titanium (Ti64) alloy femoral components. While a detailed characterization of the tribological behavior is the subject of part II, part I focusses on the deposition of pure (a-C:H) and tungsten-doped hydrogen-containing amorphous carbon coatings (a-C:H:W) and the detailed characterization of their chemical, cytological, mechanical and adhesion behavior. The coatings are fabricated by physical vapor deposition (PVD) and display typical DLC morphology and composition, as verified by focused ion beam scanning electron microscopy and Raman spectroscopy. Their roughness is higher than that of the plain substrates. Initial screening with contact angle and surface tension as well as in vitro testing by indirect and direct application indicate favorable cytocompatibility. The DLC coatings feature excellent mechanical properties with a substantial enhancement of indentation hardness and elastic modulus ratios. The adhesion of the coatings as determined in modified scratch tests can be considered as sufficient for the use in TKAs. [ABSTRACT FROM AUTHOR]

Herein, we produced a series of ultrahigh molecular weight polyethylene/polypropylene (UHMWPE/PP) blends by elongational-flow-field dominated eccentric rotor extruder (ERE) and shear-flow-field dominated twin screw extruder (TSE) respectively and presented a detailed comparative study on microstructures and tribological properties of UHMWPE/PP by different processing modes. Compared with the shear flow field in TSE, the elongational flow field in ERE facilitates the dispersion of PP in the UHMWPE matrix and promotes the interdiffusion of UHMWPE and PP molecular chains. For the first time, we discovered the presence of the interlayer phase in blends with different processing modes by using Raman mapping inspection. The elongational flow field introduces strong interaction to enable excellent compatibility of UHMWPE and PP and induces more pronounced interlayer phase with respect to the shear flow field, eventually endowing UHMWPE/PP with improved wear resistance. The optimized UHMWPE/PP (85/15) blend processed by ERE displayed higher tensile strength (25.3 MPa), higher elongation at break (341.77%) and lower wear loss of ERE-85/15 (1.5 mg) compared to the blend created by TSE. By systematically investigating the microstructures and mechanical properties of blends, we found that with increased content of PP, the wear mechanism of blends varies from abrasive wear, fatigue wear, to adhesion wear as the dominant mechanism for two processing modes. [ABSTRACT FROM AUTHOR]

Diamond-like carbon coatings may decrease implant wear, therefore, they are helping to reduce aseptic loosening and increase service life of total knee arthroplasties (TKAs). This two-part study addresses the development of such coatings for ultrahigh molecular weight polyethylene (UHMWPE) tibial inlays as well as cobalt-chromium-molybdenum (CoCr) and titanium (Ti64) alloy femoral components. While the deposition of a pure (a-C:H) and tungsten-doped hydrogen-containing amorphous carbon coating (a-C:H:W) as well as the detailed characterization of mechanical and adhesion properties were the subject of Part I, the tribological behavior is studied in Part II. Pin-on-disk tests are performed under artificial synovial fluid lubrication. Numerical elastohydrodynamic lubrication modeling is used to show the representability of contact conditions for TKAs and to assess the influence of coatings on lubrication conditions. The wear behavior is characterized by means of light and laser scanning microscopy, Raman spectroscopy, scanning electron microscopy and particle analyses. Although the coating leads to an increase in friction due to the considerably higher roughness, especially the UHMWPE wear is significantly reduced up to a factor of 49% (CoCr) and 77% (Ti64). Thereby, the coating shows continuous wear and no sudden failure or spallation of larger wear particles. This demonstrated the great potential of amorphous carbon coatings for knee replacements. [ABSTRACT FROM AUTHOR]

The aim of the present work is to provide a methodology to evaluate the influence of stacking sequence on the ballistic performance of ultra-high molecular weight polyethylene (UHMWPE) protections. The proposed methodology is based on the combination of experimental tests, numerical modelling, and Artificial Neural Networks (ANN). High-velocity impact experimental tests were conducted to validate the numerical model. The validated Finite Element Method (FEM) model was used to provide data to train and to validate the ANN. Finally, the ANN was used to find the best stacking sequence combining layers of three UHMWPE materials with different qualities. The results showed that the three UHMWPE materials can be properly combined to provide a solution with a better ballistic performance than using only the material with highest quality. These results imply that costs can be reduced increasing the ballistic limit of the UHMWPE protections. When the weight ratios of the three materials remain constant, the optimal results occur when the highest-performance material is placed in the back face. Furthermore, ANN simulation showed that the optimal results occur when the weight ratio of the highest-performance material is 79.2%. [ABSTRACT FROM AUTHOR]

Polymeric joints, made of biomedical polyethylene (UHMWPE) nanocomposite sheets, were welded with a diode laser. Since polyethylene does not absorb laser light, nanocomposites were prepared containing different percentages by weight of titanium dioxide as it is a laser absorbent. The joints were first analyzed with static mechanical tests to establish the best percentage weight content of filler that had the best mechanical response. Then, the nanocomposites containing 1 wt% titanium dioxide were selected (white color) to be subjected to fatigue tests. The experimental results were also compared with those obtained on UMMWPE with a different laser light absorbent nano filler (carbon, with greater laser absorbing power, gray in color), already studied by our research team. The results showed that the two types of joints had an appreciable resistance to fatigue, depending on the various loads imposed. Therefore, they can be chosen in different applications of UHMWPE, depending on the stresses imposed during their use. [ABSTRACT FROM AUTHOR]

Natural-fiber-reinforced polymer composites have recently drawn attention as new materials for ballistic armor due to sustainability benefits and lower cost as compared to conventional synthetic fibers, such as aramid and ultra-high-molecular-weight polyethylene (UHMWPE). In the present work, a comparison was carried out between the ballistic performance of UHMWPE composite, commercially known as Dyneema, and epoxy composite reinforced with 30 vol % natural fibers extracted from pineapple leaves (PALF) in a hard armor system. This hard armor system aims to provide additional protection to conventional level IIIA ballistic armor vests, made with Kevlar, by introducing the PALF composite plate, effectively changing the ballistic armor into level III. This level of protection allows the ballistic armor to be safely subjected to higher impact projectiles, such as 7.62 mm caliber rifle ammunition. The results indicate that a hard armor with a ceramic front followed by the PALF/epoxy composite meets the National Institute of Justice (NIJ) international standard for level III protection and performs comparably to that of the Dyneema plate, commonly used in armor vests. [ABSTRACT FROM AUTHOR]

The temperature and strain rate significantly affect the ballistic performance of UHMWPE, but the deformation of UHMWPE under thermo-mechanical coupling has been rarely studied. To investigate the influences of the temperature and the strain rate on the mechanical properties of UHMWPE, a Split Hopkinson Pressure Bar (SHPB) apparatus was used to conduct uniaxial compression experiments on UHMWPE. The stress–strain curves of UHMWPE were obtained at temperatures of 20–100 °C and strain rates of 1300–4300 s−1. Based on the experimental results, the UHMWPE belongs to viscoelastic–plastic material, and a hardening effect occurs once UHMWPE enters the plastic zone. By comparing the stress–strain curves at different temperatures and strain rates, it was found that UHMWPE exhibits strain rate strengthening and temperature softening effects. By modifying the Sherwood–Frost model, a constitutive model was established to describe the dynamic mechanical properties of UHMWPE at different temperatures. The results calculated using the constitutive model were in good agreement with the experimental data. This study provides a reference for the design of UHMWPE as a ballistic-resistant material. [ABSTRACT FROM AUTHOR]

This study presents a detailed analysis of thermal and radiation resistances of low density polyethylene (LDPE)/ultra-high molecular weight polyethylene (UHMWPE) blends containing hydroxyapatite as functional filler and rosemary acting as antioxidant against oxidative degradation. Three main procedures, chemiluminescence (CL), Fourier transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC), were applied for the determination of the degree of degradation when these materials are subjected to heat and radiation action. The crystallinity was also assessed for the characterization of diffusion peculiarities. The contributions of the mixing components are discussed based on their oxidation strength. The activation energies required for the oxidative degradation of the studied formulations were calculated. [ABSTRACT FROM AUTHOR]

In the present paper, we investigate the effectiveness of nanocomposites (composed of ultra-high molecular weight polyethylene (UHMWPE) mixed with carbon nano-filler (CNF) and medical grade paraffin oil (PO), from the biological point of view. Wear measurements were carried out without (air) and with lubricant (distilled water, natural, and artificial lubricant), and antibacterial activity and cytotoxicity were evaluated. The results highlighted that the presence of CNF is important in the nanocomposite formulation because it reduces the wear rate and prevents oxidative degradation during its processing. An amount of 1.0 wt % of CNF is best because it reaches the optimal distribution within the polymeric matrix, resulting in the best wear resistant, bio-active, and anti-bacterial nanocomposite among all investigated samples. [ABSTRACT FROM AUTHOR]

Modified ultra-high-molecular-weight polyethylene (UHMWPE) with calcium stearate (CS) and polyethylene wax (PEW) is a feasible method to improve the fluidity of materials because of the tense entanglement network formed by the extremely long molecular chains of UHMWPE, and a modified UHMWPE sheet was fabricated by compression molding technology. A Fourier-transform infrared spectroscopy test found that a new chemical bond was generated at 1097 cm−1 in the materials. Besides, further tests on the thermal, thermomechanical, mechanical, and shape memory properties of the samples were also conducted, which indicates that all properties are affected by the dimension and distribution of crystal regions. Moreover, the experimental results indicate that the addition of PEW and CS can effectively improve the mechanical properties. Additionally, the best comprehensive performance of the samples was obtained at the PEW content of 5 wt % and the CS content of 1 wt %. In addition, the effect of temperature on the shape memory properties of the samples was investigated, and the results indicate that the shape fixity ratio (Rf) and the shape recovery ratio (Rr) can reach 100% at 115 °C and 79% at 100 °C, respectively, which can contribute to the development of UHMWPE-based shape memory polymers. [ABSTRACT FROM AUTHOR]

This research focuses on developing a novel ultra high molecular weight polyethylene (UHMWPE) material reinforced with titanium dioxide (TiO 2 ) nanoparticles for producing craniofacial prostheses via an incremental sheet forming process (SPIF). First, UHMWPE-TiO 2 nanocomposite sheets were produced using incipient wetting and the compression molding process by considering different concentrations of TiO 2 nanoparticles. Then, the influence that the compression molding fabrication process has on the crystallinity and structural properties of the produced sample sheets was investigated. Experimental characterizations via scanning electron microscopy (SEM), differential scanning calorimetry (DSC), X-ray diffraction (XRD), Fourier transform infrared (FT-IR), tensile mechanical testing, and live/dead cell viability assays provided data that show an enhancement of the physical, mechanical, and biological properties. Finally, modifications on the nanocomposite material properties due to the SPIF manufacturing processes of a craniofacial prosthesis are addressed. [ABSTRACT FROM AUTHOR]

This study aims to assess whether ultra-high-molecular-weight polyethylene (UHMWPE) fibers can be successfully embedded in a polylactic acid (PLA) matrix in a material extrusion 3D printing (ME3DP) process, despite the apparent thermal incompatibility between the two materials. The work started with assessing the maximum PLA extrusion temperatures at which UHMWPE fibers withstand the 3D printing process without melting or severe degradation. After testing various fiber orientations and extrusion temperatures, it has been found that the maximum extrusion temperature depends on fiber orientation relative to extrusion pathing and varies between 175 °C and 185 °C at an ambient temperature of 25 °C. Multiple specimens with embedded strands of UHMWPE fibers have been 3D printed and following tensile strength tests on the fabricated specimens, it has been found that adding even a small number of fiber strands laid in the same direction as the load increased tensile strength by 12% to 23% depending on the raster angle, even when taking into account the decrease in tensile strength due to reduced performance of the PLA substrate caused by lower extrusion temperatures. [ABSTRACT FROM AUTHOR]

To improve properties such as thermal conductivity, low temperature thermal strain, and creep resistance of ultra-high molar mass polyethylene (UHMMPE) fibers, several researchers have previously undertaken efforts to crosslink these fibers using radiation. Ionizing radiation is commonly used to crosslink bulk UHMMPE in other applications, such as artificial joints. However, UHMMPE fibers differ from bulk UHMMPE in that they have a higher crystallinity (approximately 85% to 90%) and are very highly oriented during manufacturing in which the fibers are stretched 50 to 100 times their original length. Thus, the amorphous fraction of the UHMMPE fibers is also highly ordered. Several experiments were conducted to crosslink the UHMMPE fibers using both low dose rate (gamma) and high dose rate (electron beam) irradiation, all in the absence of oxygen. In all cases, the tensile strength of the fiber was greatly reduced by the irradiation. The oxidation index was also measured for the irradiated samples, and oxidation was not found to play a major role in the reduction of tensile strength in the fibers after irradiation. While this work did not achieve the desired result of improving the mechanical properties of the UHMMPE fiber, a significant result was found. The electron paramagnetic resonance (EPR) spectrum of the UHMMPE fibers was measured shortly after irradiation, and a mixture of allyl and alkyl radicals were detected. The irradiated samples were stored in dark ambient conditions for at least six years, then reexamined using EPR for free radical characterization. Surprisingly, the gamma-irradiated samples showed clear evidence of long-lived polyenyl radicals present in the material. Free radicals are very reactive species that will typically migrate to the surface of the crystalline domain and decay in a relatively short time through various reactions in the amorphous regions. It is hypothesized herein that due to the high crystallinity and large anisotropy of the highly drawn UHMMPE fiber, the polyenyl radicals were trapped in the crystal phase and were unable to migrate and decay. An experiment was performed to test this hypothesis, by which samples of the irradiated fibers were heated to temperatures above first the alpha relaxation and then melting point of polyethylene, and EPR measurements were taken. Results showed that the polyenyl radical signal persisted below the Tm, but was rapidly eliminated upon melting of the crystals. These experiments support the hypothesis that the long-lived polyenyl radicals are trapped in the crystalline region of the polyethylene fibers. [ABSTRACT FROM AUTHOR]

Highly oriented UHMWPE films were reinforced with functionalized graphene nanoplates (GNP). GNP was functionalized by deposition of polyaniline (PANI) on the GNP surface. The structure of GNP/PANI was studied by Raman spectroscopy, and the structure of xerogels and films based on UHMWPE was studied by DSC and SEM. PANI promotes the reduction of the GNP aggregation in the UHMWPE matrix and increases the degree of crystallinity due to heterogeneous crystallization. The new lamellar crystal structure has a high drawability. The highest value of the tensile strength 1330 MPa (an increase of 45%) was obtained with a filler content of 2 wt % GNP/PANI, and the highest value of Young's modulus 41 GPa (an increase of 32%) was obtained with a filler content of 1 wt % GNP/PANI. The effect of GNP with PANI fillers on the dynamic mechanical properties of the UHMWPE films was discussed. [ABSTRACT FROM AUTHOR]

Ultra High molecular weight polyethylene (UHMWPE) suffers wear degradation in total joint replacements and it needs to be improved. Thus, we enhanced wear resistance of UHMWPE with carbon nanofiller and paraffin oil and studied its tribological behavior in Simulated Synovial Fluid (SSF) for 60 days at 37 °C to reproduce the conditions of a real joint. Ageing in biological fluid accelerates the wear action but nanocomposite exhibited a higher wear resistance compared to UHMWPE because of its higher structural homogeneity. Carbon nanofiller closes the porosity of UHMWPE hindering SSF to penetrate inside. Wear resistance of the nanocomposite with 1.0 wt.% of CNF improved of 65% (before ageing) and of 70% (after 60 days in SSF) with respect to pure UHMWPE. [ABSTRACT FROM AUTHOR]

A series of ultrahigh molecular weight polyethylenes with viscosity-average molecular weights in the range of 1.6–5.6 × 106 have been prepared by using a novel Ziegler–Natta-type catalytic system—TiCl4/2,2′-dimethoxy-1,1′-binaphthalene/Et3Al2Cl3/Bu2Mg at different temperatures (Tpoly) in the range between 10 and 70 °C in toluene. The morphology of the nascent reactor powders has been studied by scanning electron microscopy, wide-angle X-ray diffraction, and the DSC melting behavior. Polymers are suitable for the modern processing methods—the solvent-free solid-state formation of super high-strength (tensile strength over 1.8–2.5 GPa) and high-modulus (elastic modulus up to 136 GPa) oriented film tapes. With decrease of Tpoly, the drawability of the reactor powders increased significantly. [ABSTRACT FROM AUTHOR]