Search

Composites revolutionize material performance, fostering innovation and efficiency in diverse sectors. Elastomer-based polymeric composites are crucial for applications requiring superior mechanical strength and durability. Widely applied in automotives, aerospace, construction, and consumer goods, they excel under extreme conditions. Composites based on recycled rubber, fortified with reinforcing fillers, represent a sustainable material innovation by repurposing discarded rubber. The integration of reinforcing agents enhances the strength and resilience of this composite, and the recycled polymeric matrix offers an eco-friendly alternative to virgin elastomers, reducing their environmental impact. Devulcanized rubber, with inherently lower mechanical properties than virgin rubber, requires enhancement of its quality for reuse in a circular economy: considerable amounts of recycled tire rubber can only be applied in new tires if the property profile comes close to the one of the virgin rubber. To achieve this, model passenger car tire and whole tire rubber granulates were transformed into elastomeric composites through optimized devulcanization and blending with additional fillers like carbon black and silica–silane. These fillers were chosen as they are commonly used in tire compounding, but they lose their reactivity during their service life and the devulcanization process. Incorporation of 20% (w/w) additional filler enhanced the strength of the devulcanizate composites by up to 15%. Additionally, increased silane concentration significantly further improved the tensile strength, Payne effect, and dispersion by enhancing the polymer–filler interaction through improved silanization. Higher silane concentrations reduced elongation at break and increased crosslink density, as it leads to a stable filler–polymer network. The optimal concentration of a silica–silane filler system for a devulcanizate was found to be 20% silica with 3% silane, showing the best property profile. [ABSTRACT FROM AUTHOR]

This study investigated the synergistic effect of carbon black/multi-wall carbon nanotube (CB/MWCNT) hybrid fillers on the physical and mechanical properties of Ethylene propylene diene rubber (EPDM) composites after exposure to high-pressure hydrogen gas. The EPDM/CB/CNT hybrid composites were prepared by using the EPDM/MWCNT master batch (MB) with 10 phr CNTs to enhance the dispersion of CNTs in hybrid composites. The investigation included a detailed analysis of cure characteristics, crosslink density, Payne effect, mechanical properties, and hydrogen permeation properties. After exposure to 96.3 MPa hydrogen gas, the hydrogen uptake and the change in volume and mechanical properties of the composites were assessed. We found that as the MWCNT volume fraction in fillers increased, the crosslink density, filler–filler interaction, and modulus of hybrid composites increased. The hydrogen uptake and the solubility of the composites decreased with an increasing MWCNT volume fraction in fillers. Moreover, after exposure to hydrogen gas, the change in volume and mechanical properties exhibited a diminishing trend with a higher MWCNT volume fraction. We conclude that the hybridization of CB and CNTs formed strong filler–filler networks in hybrid composites, consequently reinforcing the EPDM composites and enhancing the barrier properties of hydrogen gas. [ABSTRACT FROM AUTHOR]

Three types of composites were tested for electromagnetic interference (EMI) absorption shielding effectiveness, the curing process, and their physical–mechanical properties. For the first type of composites, nickel–zinc ferrite, manganese–zinc ferrite, and both fillers in their mutual combinations were incorporated into acrylonitrile–butadiene rubber. The overall content of the filler, or fillers, was kept at 200 phr. Then, carbon black or carbon fibers were incorporated into each rubber formulation at a constant loading of—25 phr, while the content of magnetic fillers was unchanged, at —200 phr. This work focused on the understanding of correlations between the electromagnetic shielding parameters and electrical conductivity of composites in relation to their EMI absorption shielding effectiveness. The absorption shielding abilities of materials were evaluated within a frequency bandwidth from 1 MHz to 6 GHz. This study revealed good correlation among permittivity, conductivity, and EMI absorption effectiveness. Although the absorption shielding efficiency of composites filled only with ferrites seems to be the highest, the absorption maxima of those composites reached over 6 GHz. The application of carbon-based fillers resulted in the higher electrical conductivity and higher permittivity of composites, which was reflected in their lower absorption shielding performance. However, the composites filled with ferrites and carbon-based fillers absorbed electromagnetic radiation within the desired frequency range. The presence of carbon-based fillers caused improvement in the tensile behavior of composites. This study also demonstrated that the higher the ratio of nickel–zinc ferrite in combined magnetic fillers, the better the absorption shielding efficiency. [ABSTRACT FROM AUTHOR]

The development of thermally conductive rubber nanocomposites for heat management poses a formidable challenge in numerous applications, notably within the realm of tire technology. Notably, rubber materials are characterized by their inherently low thermal conductivity. Consequently, it becomes imperative to incorporate diverse conductive fillers to mitigate the propensity for heat build-up. Multi-walled carbon nanotubes (MWCNTs), as reinforcement agents within the tire tread compounds, have gained considerable attention owing to their extraordinary attributes. The attainment of high-performance rubber nanocomposites hinges significantly on the uniform distribution of MWCNT. This study presents the influence of MWCNTs on the performance of carbon black (CB)-reinforced natural rubber (NR)/styrene butadiene rubber (SBR) tire compounds prepared via high shear melt mixing. Morphological analysis showed a good distribution of MWCNTs in the NR/SBR/CB compound. The vulcanization parameters, such as the maximum and minimum torque, cross-linking density, hardness, abrasion resistance, tensile strength, and Young modulus, exhibited a progressive improvement with the addition of MWCNT. Remarkably, adding MWCNT into CB improved the heat conductivity of the NR/SBR/CB compounds, hence decreasing the heat build-up. A percolation mode was also proposed for the hybrid carbon fillers based on the data obtained. [ABSTRACT FROM AUTHOR]

Modelling the flow properties of rubber blends makes it possible to predict their rheological behaviour during the processing and production of rubber-based products. As the nonlinear nature of such complex processes complicates the creation of exact analytical models, it is appropriate to use artificial intelligence tools in this modelling. The present study was implemented to develop a highly efficient artificial neural network model, optimised using a novel training algorithm with fast parallel computing to predict the results of rheological tests of rubber blends performed under different conditions. A series of 120 real dynamic viscosity–time curves, acquired by a rubber process analyser for styrene–butadiene rubber blends with varying carbon black contents vulcanised at different temperatures, were analysed using a Generalised Regression Neural Network. The model was optimised by limiting the fitting error of the training dataset to a pre-specified value of less than 1%. All repeated calculations were made via parallel computing with multiple computer cores, which significantly reduces the total computation time. An excellent agreement between the predicted and measured generalisation data was found, with an error of less than 4.7%, confirming the high generalisation performance of the newly developed model. [ABSTRACT FROM AUTHOR]

The present work aims to study the effect of glycerol as a replacement for mineral oils in natural rubber (NR) composites to obtain suitable properties via cure characteristics, mechanical properties, and thermal stability. Glycerol was used at a 5 phr rate in the compound with carbon black as a reinforcing filler and was compared to mineral processing oils such as aromatic oil, treated distillate aromatic extracted oil, and paraffinic oil. Compared to the other oils, glycerol exhibits better maximum torque and torque differences. Also, a shorter scorch time, cure time, and a higher cure rate index of the compounds were observed. However, although the received mechanical properties, including tensile strength, elongation at break, and compression set of the vulcanized rubber using glycerol showed slightly lower values than the others, the 100% and 300% moduli, as well as the hardness of the composites filled with glycerol, exhibit better values relative to the other commercial oils. These findings demonstrate that glycerol overall presents a good balance of properties, making it beneficial to use glycerol as a substitute for mineral oil in tire, shoe sole, and rubber stopper applications. [ABSTRACT FROM AUTHOR]

Nowadays, waste tires have emerged as one of the most significant sources of environmental pollution. To address this issue, pyrolysis has become a widely adopted method. The continuous rotary kiln reactor has particularly gained popularity in industrial production for pyrolysis due to its suitability. In order to guide the development of new industrial continuous rotary kiln reactors and achieve high-performance pyrolytic carbon black (CBp), this study was conducted to investigate the relationship between the physical and chemical characteristics of CBp and pyrolysis temperature. The elevated-temperature procedure led to a reduction in DBP values from 90 to 70 mL/100 mg, accompanied by a rise in the specific surface area from 63 to 77 m2/g. The augmentation of pyrolysis temperature was noted to induce the agglomeration of CBp particles, thereby negatively impacting their dispersion within polymer matrices. CBp particles at 550 °C exhibited greater structural order, as determined by Raman spectroscopy, which can be attributed to the elevated temperature proximate to the cylinder wall surface. Furthermore, the potential of CBp for reinforcement in natural rubber (NR) was taken into consideration. The pronounced propensity of high-temperature CBps to agglomerate led to uneven dispersion within the polymer, consequently causing heightened heat accumulation and the emergence of the Payne effect. Based on a thorough analysis of the outcomes, the optimal pyrolysis temperature for CBp synthesis within the continuous reactor was ascertained. [ABSTRACT FROM AUTHOR]

Elastomer composites with low hysteresis are of great importance for sustainable development, as they find application in billions of tires. For these composites, a filler such as silica, able to establish a chemical bond with the elastomer chains, is used, in spite of its technical drawbacks. In this work, a furnace carbon black (CB) functionalized with polar groups was used in replacement of silica, obtaining lower hysteresis. CBN326 was functionalized with 2-(2,5-dimethyl-1H-pyrrol-1-yl)-1,3-propanediol (serinol pyrrole, SP), and samples of CB/SP adducts were prepared with different SP content, ranging from four to seven parts per hundred carbon (phc). The entire process, from the synthesis of SP to the preparation of the CB/SP adduct, was characterized by a yield close to 80%. The functionalization did not alter the bulk structure of CB. Composites were prepared, based on diene rubbers—poly(1,4-cis-isoprene) from Hevea Brasiliensis and poly(1,4-cis-butadiene) in a first study and synthetic poly(1,4-cis-isoprene) in a second study—and were crosslinked with a sulfur-based system. A CB/silica hybrid filler system (30/35 parts) was used and the partial replacement (66% by volume) of silica with CB/SP was performed. The composites with CB/SP exhibited more efficient crosslinking, a lower Payne effect and higher dynamic rigidity, for all the SP content, with the effect of the functionalized CB consistently increasing the amount of SP. Lower hysteresis was obtained for the composites with CB/SP. A CB/SP adduct with approximately 6 phc of SP, used in place of silica, resulted in a reduction in ΔG′/G′ of more than 10% and an increase in E' at 70 °C and in σ300 in tensile measurements of about 35% and 30%, respectively. The results of this work increase the degrees of freedom for preparing elastomer composites with low hysteresis, allowing for the use of either silica or CB as filler, with a potentially great impact on an industrial scale. [ABSTRACT FROM AUTHOR]

This study aims to analyze tire wear particulate matter (TWP) from tread rubber with different formulations and to compare the concentration of TWP with different wear devices. The TWP generated during the abrasion of truck and bus radial (TBR) tires were examined, and the effect of using different types of rubber and carbon black (CB) were investigated. When natural rubber (NR) was solely used as the tire tread rubber material, there was a higher concentration of 5–10 µm TWP. However, when the tread formulation consisted of NR mixed with butadiene rubber, the TWP concentration decreased. Changing the type of CB also reduced the amount of TWP in the 2.5 µm size range. The TWP concentration in the specimens increased with increasing speed and vertical load. The TWP generated during the abrasion tests using wear testers and tire simulators exhibited similar trends. These findings suggest that modifying tire tread formulations can effectively control the distribution and amount of TWP generation. [ABSTRACT FROM AUTHOR]

Natural rubber composites were reinforced by the co-fillers 'hydrochar' (HC), obtained by hydrothermal carbonization of hardwood sawdust and commercial carbon black (CB). The content of the combined fillers was kept constant while their ratio was varied. The aim was to test the suitability of HC as a partial filler in natural rubber. Due to its larger particle size and hence smaller specific surface area, large amounts of HC reduced the crosslinking density in the composites. On the other hand, due to its unsaturated organic character, HC was found to display interesting chemical effects: if it was used as the exclusive filler component, it displayed a very strong anti-oxidizing effect, which greatly stabilized the rubber composite against oxidative crosslinking (and hence embrittlement). HC also affected the vulcanization kinetics in different ways, depending on the HC/CB ratio. Composites with HC/CB ratios 20/30 and 10/40 displayed interesting chemical stabilization in combination with fairly good mechanical properties. The performed analyses included vulcanization kinetics, tensile properties, determination of density of permanent and reversible crosslinking in dry and swollen states, chemical stability tests including TGA, thermo-oxidative aging tests in air at 180 °C, simulated weathering in real use conditions ('Florida test'), and thermo-mechanical analyses of degraded samples. Generally, the results indicate that HC could be a promising filler material due to its specific reactivity. [ABSTRACT FROM AUTHOR]

This study presents the functional effects of BaTiO3 powder loaded in ethylene–propylene–diene rubber (EPDM) in three concentrations: 0, 1, and 2.5 phr. The characterization of mechanical properties, oxidation strength, and biological vulnerability is achieved on these materials subjected to an accelerated degradation stimulated by their γ-irradiation at 50 and 100 kGy. The thermal performances of these materials are improved when the content of filler becomes higher. The results obtained by chemiluminescence, FTIR-ATR, and mechanical testing indicate that the loading of 2.5 phr is the most proper composition that resists for a long time after it is γ-irradiated at a high dose. If the oxidation starts at 176 °C in the pristine polymer, it becomes significant at 188 and 210 °C in the case of composites containing 1 and 2.5 phr of filler, respectively. The radiation treatment induces a significant stability improvement measured by the enlargement of temperature range by more than 1.5 times, which explains the durability growth for the radiation-processed studied composites. The extension of the stability period is also based on the interaction between degrading polymer substrate and particle surface in the composite richest in titanate fraction when the exposure is 100 kGy was analyzed. The mechanical testing as well as the FTIR investigation clearly delimits the positive effects of carbon black on the functionality of EPDM/BaTiO3 composites. The contribution of carbon black is a defining feature of the studied composites based on the nucleation of the host matrix by which the polymer properties are effectively ameliorated. [ABSTRACT FROM AUTHOR]

Recently, hybrid fillers have been found to be more advantageous in energy-harvesting composites. This study investigated the mechanical and electromechanical performances of silicone rubber-based composites made from hybrid fillers containing conductive nanocarbon black (NCB) and molybdenum disulfide (MoS2). A hybrid filler system containing only 3 phr (per hundred grams of rubber) MoS2 and 17 phr NCB provided higher fracture strain, better tensile strength, and excellent toughness values compared to the 20 phr NCB-only-filled and 5 phr MoS2-only-filled rubber composites. The chemical cross-link densities suggest that NCB promoted the formation of cross-links, whereas MoS2 slightly reduced the cross-link density. The higher mechanical properties in the hybrid filler systems suggest that the filler particles were more uniformly distributed, which was confirmed by the scanning electron microscope study. Uniformly distributed filler particles with moderate cross-link density in hybrid filler systems greatly improved the fracture strain and fracture toughness. For example, the hybrid filler with a 17:3 ratio of NCB to MoS2 showed a 184% increment in fracture toughness, and a 93% increment in fracture strain, compared to the 20 phr NCB-only-filled composite. Regarding electromechanical sensing with 2 kPa of applied cyclic pressure, the hybrid filler (17:3 CB to MoS2) performed significantly better (~100%) than the 20 phr NCB-only compound. This may have been due to the excellent distribution of conducting NCB networks and piezoelectric MoS2 that caused symmetric charging–discharging in the toughened hybrid composite. Thus, hybrid composites with excellent fatigue resistance can find dynamic applications, such as in blood pressure measurement. [ABSTRACT FROM AUTHOR]

In this work, the contribution of different types of carbon blacks (N115, N330, N550, N660) and their primary and secondary thermally cracked recovered carbon blacks to the mechanical properties of NR composites was evaluated. The thermally cracked recovered carbon blacks were prepared by cracking the rubber composites at 500 °C and de-hybridizing them at 900 °C. The characterization of the thermally cracked recovered carbon blacks by scanning electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy showed that carbon blacks after primary and secondary thermal cracking recovery were more prone to aggregation and exhibited a higher degree of carbon defects. The number and type of functional groups on the surface of these carbon blacks were significantly reduced. For NR composites with pristine samples added, the mechanical properties and the bound rubber content tests showed that the mechanical properties of the NR composites became weaker with the increase in carbon black particle size. The bound rubber content also decreased with increased carbon black particle size. The mechanical properties of the NR composites reinforced with carbon black recovered by primary and secondary thermal cracking would therefore decrease. The results of AFM and DSC tests further confirmed the decreasing trend of bound rubber. The present work demonstrates the effect of bound rubber content variation on the mechanical properties of rubber, demonstrates the morphology of bound rubber more visually, and provides new insights into the reinforcement theory of CB. [ABSTRACT FROM AUTHOR]

The smoke emitted during thermal decomposition of elastomeric composites contains a significant number of carcinogenic and mutagenic compounds from the group of polycyclic aromatic hydrocarbons, PAHs, as well as polychlorinated dibenzo-p-dioxins and furans, PCDDs/Fs. By replacing carbon black with a specific amount of lignocellulose filler, we noticeably reduced the fire hazard caused by elastomeric composites. The lignocellulose filler reduced the parameters associated with the flammability of the tested composites, decreased the smoke emission, and limited the toxicity of gaseous decomposition products expressed as a toximetric indicator and the sum of PAHs and PCDDs/Fs. The natural filler also reduced emission of gases that constitute the basis for determination of the value of the toximetric indicator WLC50SM. The flammability and optical density of the smoke were determined in accordance with the applicable European standards, with the use of a cone calorimeter and a chamber for smoke optical density tests. PCDD/F and PAH were determined using the GCMS-MS technique. The toximetric indicator was determined using the FB-FTIR method (fluidised bed reactor and the infrared spectrum analysis). [ABSTRACT FROM AUTHOR]

Filler reinforced rubber is widely used for engineering applications; therefore, a sound characterization of the effects of physical aging is crucial for accurately predicting its viscoelastic properties within its operational temperature range. Here, the torsion pendulum is used to monitor the evolution of the storage and loss modulus of carbon black filled samples for four days after a temperature drop to 30   ° C . The storage modulus presents a continuous increase, while the loss modulus generally displays a steady decrease throughout the four days that each test was conducted. The relationship of the recovery rates with the carbon black properties is also studied, analysing its dependency on the particle size and aggregate structure. The evolution of the recovery rate seems to depend linearly on the surface area while the carbon black structure appears to have a much weaker influence on the physical aging behavior for the set of compounds tested. The obtained results corroborate the presence of physical aging at room temperature for filler rubber materials and the ability of the torsion pendulum to monitor the storage and loss modulus change, providing pivotal data on the influence of physical aging on the viscoelastic properties of the material. [ABSTRACT FROM AUTHOR]

The Payne Effect (also known as the Fletcher–Gent Effect) has a fundamental impact on the behavior of filled rubber composites and therefore must be considered during their design. This study investigates the influence of carbon black (CB) surface area and structure on the observed Payne Effect and builds on the existing models of Kraus and Ulmer to explain this phenomenon. Dynamic strain sweeps were carried out on natural rubber (NR) compounds containing eight different grades of CB at equivalent volume fractions. The loss and storage moduli were modeled according to the Kraus and Ulmer equations, using a curve optimization tool in SciPy. Subsequent regression analysis provided strong correlations between the fitting parameters and the CB structure and surface area. Using this regression analysis, this work provides further insight into the physical meaning behind the Kraus and Ulmer models, which are phenomenological in nature. [ABSTRACT FROM AUTHOR]

A new generation biomass-based filler for natural rubber, 'hydrochar' (HC), was obtained by hydrothermal carbonization of hardwood waste (sawdust). It was intended as a potential partial replacement for the traditional carbon black (CB) filler. The HC particles were found (TEM) to be much larger (and less regular) than CB: 0.5–3 µm vs. 30–60 nm, but the specific surface areas were relatively close to each other (HC: 21.4 m2/g vs. CB: 77.8 m2/g), indicating a considerable porosity of HC. The carbon content of HC was 71%, up from 46% in sawdust feed. FTIR and 13C-NMR analyses indicated that HC preserved its organic character, but it strongly differs from both lignin and cellulose. Experimental rubber nanocomposites were prepared, in which the content of the combined fillers was set at 50 phr (31 wt.%), while the HC/CB ratios were varied between 40/10 and 0/50. Morphology investigations proved a fairly even distribution of HC and CB, as well as the disappearance of bubbles after vulcanization. Vulcanization rheology tests demonstrated that the HC filler does not hinder the process, but it significantly influences vulcanization chemistry, canceling scorch time on one hand and slowing down the reaction on the other. Generally, the results suggest that rubber composites in which 10–20 phr of CB are replaced by HC might be promising materials. The use of HC in the rubber industry would represent a high-tonnage application for hardwood waste. [ABSTRACT FROM AUTHOR]

With the rapid development of the palm oil-related industry, this has resulted in the high production of palm oil waste. The increasing amount of palm oil waste has become an alarming issue in which researchers have carried out studies that this palm oil waste has the potential to be used as a biomass source. Carbon black (CB) is the most preferred reinforcing filler in the rubber industry but it has a disadvantage where CB is carcinogenic and a petroleum-based product. Hence CB is less sustainable. Palm kernel shell (PKS) derived from palm oil waste can be turned into palm kernel shell biochar (PKSBc) which can potentially be a value-added, sustainable biofiller as reinforcement in rubber composites. In this study, PKSBc is hybridized with CB (N660) at different loading ratios to be filled in carboxylated nitrile butadiene rubber (XNBR). This study aims to elucidate the effect of the varying ratios of hybrid CB/PKSBc on the rheological properties, abrasion resistance, and hardness of XNBR composites. In this study, both CB and PKSBc are incorporated into XNBR and were then cured with sulphur. The composites were prepared by using a two-roll mill. Different compositions of hybrid CB/PKSBc were incorporated. The rheological properties and physicomechanical properties, such as abrasion resistance and hardness of the vulcanizates, were investigated. Based on the results, as the loading ratio of PKSBc in hybrid CB/PKSBc increases, the cure time decreases, and the cure rate index increases. The abrasion resistance and hardness values of vulcanizates were maintained by the high loading of PKSBc which was due to the porous structure of PKSBc as shown in the morphological analysis of PKSBc. The pores of PKSBc provided mechanical interlocking to reduce volume loss and maintain the hardness of vulcanizates when subjected to force. With this, PKSBc is proven to be a semi-reinforcing filler that could not only act as a co-filler to existing commercialized CB, but PKSBc could also fully substitute CB as reinforcement in rubber, specifically XNBR as it is able to provide high abrasion resistance and hardness to the rubber composites. This would mean the performance of PKSBc is comparable with CB (N660) when it comes to maintaining the physicomechanical properties of XNBR composites in terms of abrasion resistance and hardness. Therefore, this approach of using eco-friendly filler derived from palm oil agricultural waste (PKSBc) can reduce the abundance of palm oil waste, be a sustainable alternative to act as a co-filler in hybrid CB/PKSBc to decrease the usage of CB, and helps to enhance the quality of existing rubber-based products. [ABSTRACT FROM AUTHOR]

Calcium lignosulfonate in the amount 30 phr was incorporated into rubber compounds based on pure NBR and an NBR carbon black batch, in which the content of carbon black was 25 phr. Glycerine, as a cheap and environmentally friendly plasticizer, was applied into both types of rubber formulations in a concentration scale ranging from 5 to 20 phr. For the cross-linking of rubber compounds, a sulfur-based curing system was used. The work was aimed at the investigation of glycerine content on the curing process and rheological properties of rubber compounds, cross-link density, morphology and physical–mechanical properties of vulcanizates. The results show that glycerine influences the shapes of curing isotherms and results in a significant decrease between the maximum and minimum torque. This points to the strong plasticizing effect of glycerine on rubber compounds, which was also confirmed from rheological measurements. The application of glycerine resulted in better homogeneity of the rubber compounds and in the better dispersion and distribution of lignosulfonate within the rubber matrix, which was subsequently reflected in the significant improvement of tensile characteristics of vulcanizates. A higher cross-link density as well as better physical–mechanical properties were exhibited by the vulcanizates based on the carbon black batch due to the presence of a reinforcing filler. [ABSTRACT FROM AUTHOR]

The mechanical properties and wear resistance of carbon black/natural rubber (CB/NR) composites are significantly influenced by the degree of CB dispersion in rubber. Here, we present a novel reinforcement theory using atomic force microscopy (AFM) to quantify the adhesive thickness of rubber molecules around the CB particles as well as the height, area, and volume in NR. The thickness of the bonded rubber (BR) was found to vary between 3 and 7 nm depending on the values of the nitrogen surface area (NSA) for CB. This indicates that a higher BR content is a result of a higher CB NSA with a smaller particle size, showing a higher number of active positions to anchor rubber molecules. The nanoindentation of AFM was used to determine the surface hardness of CB in NR; the value decreases with increasing BR height. In this study, we demonstrate a well-defined reinforcement mechanism of CB in NR with the factors of BR, surface hardness, 100%/300% modulus, and tensile strength. [ABSTRACT FROM AUTHOR]

The effects of wet mixing and traditional mixing on the properties of radial-orientation basalt fiber-reinforced rubber products were studied through experiments. The results show that compared with traditional mixing, the basalt fibers under the wet mixing conditions can more effectively enhance the physical and mechanical properties of composites. The properties of the composites, such as carbon black dispersion, filler dispersion, rolling resistance and wet-sliding resistance, were the best after the latex and carbon black were premixed and then mixed by a mixer. Through extrusion experiments with the developed short-fiber radial-orientation die, it can be found that the fluidity of composites after extrusion is enhanced. Through analysis utilizing an electron microscope, it is shown that when the BFs added with KH550 (3-Aminopropyltriethoxysilane) were modified by KH560 ((3-Glycidyloxypropyl)trimethoxysilane), the interface layers of BF (basalt fiber)–KH560–NR and BF–KH550–NR were formed, which improves the adhesion between BFs and the rubber matrix. Qualitative characterization experiments on the orientation direction of the vulcanized composites were carried out through the experiments; that is, the qualitative characterization experiments on the segmented cutting and vulcanization of the composites in the radial direction showed that the short-fiber radial-orientation die could greatly improve the radial orientation degree of the short fibers in the radial direction. After adding KH560, the performance of the composites reinforced by the short fibers was improved to a certain extent compared with those without KH560. By adding DZ (N,N-Dicyclohexyl-2-benzothiazolsulfene amide) and CTP(cytidine triphosphate disodium) into the vulcanization system, the curing process of compounds in mixing and extrusion was delayed and the scorching resistance of short-fiber-reinforced composites was enhanced. Under the same conditions, the properties of the compounds after extrusion were greatly improved compared with those without extrusion. [ABSTRACT FROM AUTHOR]

Natural rubber with 50 mol % epoxidation (ENR-50) was filled with carbon nanotubes (CNTs) and conductive carbon black (CCB) hybrid fillers with various CCB loadings of 2.5, 5.0, 7.0, 10.0 and 15.0 phr, and the compounds were mixed with ferric ion (Fe3+) as a crosslinking agent. The ENRs filled exclusively with CNTs, and CNT–CCB hybrid fillers exhibited typical curing curves at different CCB loadings, i.e., increasing torque with time and thus crosslinked networks. Furthermore, the incorporation of CNT–CCB hybrid fillers and increasing CCB loadings caused an enhancement of tensile properties (modulus and tensile strength) and crosslink densities, which are indicated by the increasing torque difference and the crosslink densities. The crosslink densities are determined by swelling and temperature scanning stress relaxation (TSSR). Increasing CCB loadings also caused a significant improvement in bound rubber content, filler–rubber interactions, thermal resistance, glass transition temperature (Tg) and electrical conductivity. A combination of 7 phr CNT and CCB with loading higher than 2.5 phr gave superior properties to ENR vulcanizates. Furthermore, the secondary CCB filler contributes to the improvement of CNT dispersion in the ENR matrix by networking the CNT capsules and forming CNT–CCB–CNT pathways and thus strong CNT–CCB networks, indicating the improvement in the tensile properties, bound rubber content and dynamic properties of the ENR composites. Moreover, higher electrical conductivity with a comparatively low percolation threshold of the hybrid composites was found as compared to the ENR filled with CNTs without CCB composite. The superior mechanical and other properties are due to the finer dispersion and even distribution of CNT–CCB hybrid fillers in the ENR matrix. [ABSTRACT FROM AUTHOR]

The basalt fibers (BF) and the basalt fibers etched by H2SO4 (BFH) were modified by polydopamine (PDA) or synergistically modified by PDA and silicon carbon black (SiCB). The effects of modified BF, BFH and SiCB on the basic mechanical properties and magnetorheological (MR) effects of natural rubber/butadiene rubber-based magnetorheological elastomer precursors (MREs) were investigated. The results show that the tensile strength, tear strength and stress at 300% strain of MREs/PDA-BFH-SiCB prepared with BFH synergistically modified by PDA and SiCB reach the maximum values, which are 9.58 MPa, 24.07 kN/m and 4.13 MPa, respectively. Additionally, its MR effect is more than three times higher than that of MREs before composite modification. [ABSTRACT FROM AUTHOR]

Natural rubber (NR) presents a number of advantages over other types of rubber but has poor resistance to chemicals and aging. The incorporation of ethylene propylene diene monomer (EPDM) into the NR matrix may be able to address this issue. Mineral fillers, such as carbon black (CB) and silica are routinely incorporated into various elastomers owing to their low cost, enhanced processability, good functionality, and high resistance to chemicals and aging. Other fillers have been examined as potential alternatives to CB and silica. In this study, phlogopite was surface-modified using 10 phr of compatibilizers, such as aminopropyltriethoxysilane (A1S), aminoethylaminopropyltrimethoxysilane (A2S), or 3-glycidoxypropyltrimethoxysilane (ES), and mixed with NR/EPDM blends. The effects of untreated and surface-treated phlogopite on the mechanical properties of the rubber blend were then compared with those of common fillers (CB and silica) for rubbers. The incorporation of surface-modified phlogopite into NR/EPDM considerably enhanced various properties. The functionalization of the phlogopite surface using silane-based matters (amino- and epoxide-functionalized) led to excellent compatibility between the rubber matrix and phlogopite, thereby improving diverse properties of the elastomeric composites, with effects analogous to those of CB. The tensile strength and elongation at break of the phlogopite-embedded NR/EPDM composite were lower than those of the CB-incorporated NR/EPDM composite by 30% and 10%, respectively. Among the prepared samples, the ES-functionalized phlogopite showed the best compatibility with the rubber matrix, exhibiting a tensile strength and modulus of composites that were 35% and 18% higher, respectively, compared with those of the untreated phlogopite-incorporated NR/EPDM composite. The ES-functionalized phlogopite/NR/EPDM showed similar strength and higher modulus (by 18%) to the CB/NR/EPDM rubber composite, despite slightly lower elongation at break and toughness. The results of rebound resilience and compression set tests indicated that the elasticity of the surface-modified phlogopite/NR/EPDM rubber composite was higher than that of the silica- and CB-reinforced composites. These improvements could be attributed to enhancements in the physical and chemical interactions among the rubber matrix, stearic acid, and functionalized (compatibilized) phlogopite. Therefore, the functionalized phlogopite can be utilized in a wide range of applications for rubber compounding. [ABSTRACT FROM AUTHOR]

The implementation of vehicle electrification and autonomous driving technologies has recently emphasized the importance of abrasion resistance and fuel efficiency of truck bus radial (TBR) tire treads that undergo high loads and long driving times. In this study, a functionalized liquid butadiene rubber (F-LqBR) was introduced to replace the treated distillate aromatic extracted (TDAE) oil as a way to improve abrasion resistance and fuel efficiency in the TBR tire tread compound and to solve the oil migration. First, radical polymerization was used to synthesize nonfunctionalized LqBR (N-LqBR) and amino-LqBR with an amine group at the chain ends. The synthesized LqBRs were then substituted in place of TDAE oil to manufacture carbon-black-filled natural rubber (NR) compounds and to evaluate their physical properties. The results show that LqBRs improved the migration resistance and enhanced the abrasion resistance by lowering the glass transition temperature (Tg) of the compound. In particular, amino-LqBR improved carbon black dispersion in the rubber matrix through a chemical bond between the functional group of the carbon black surface and the base rubber. In conclusion, amino-LqBR successfully served as a processing aid in a carbon black-filled NR compound while simultaneously enhancing its fuel efficiency and abrasion resistance. [ABSTRACT FROM AUTHOR]

The binding amount of rubber and reinforcing filler directly affects the quality of rubber products. The effect of aromatic solvent oil (S-150) on the binding amount of rubber and reinforcing filler was studied. In order to determine the suitability of rubber after adding S-150, the curing characteristics, physical performance and tensile properties of rubber samples were tested and analyzed. Meanwhile, the microstructure of the composite was analyzed by scanning electron microscopy (SEM). The test results showed that the binding amount of rubber and reinforcing filler was increased after adding S-150. The density and Shore A hardness were decreased. When carbon black was 80 phr, after adding 40 phr of S-150, the rebound resilience of rubber increased by 13% on average, and the elongation at break increased by 88% on average. When white carbon black was between 10-70 phr, after adding 65 phr of S-150, the rebound resilience of rubber increased by 9% on average, and the elongation at break increased by 51% on average. Modulus at 100% and tensile strength were decreased. Meanwhile, it could be judged from the microstructure results that the reticulation space inside the rubber was increased, the agglomerate particles were relatively uniform, and no bubbles or holes were observed. The mechanism that S-150 could increase the binding amount of rubber was analyzed according to the like-dissolves-like principle. This research achievement could lead to improvements in the quality of rubber products and promote their practical application. [ABSTRACT FROM AUTHOR]

We studied the effects of silicon carbide (SiC) and SiC hybrid systems with different conventional fillers (silica, carbon black, graphene, hydrotalcite, halloysite) on the rheometric measurements, crosslink density, mechanical performance, aging stability, morphology, thermal behaviour, and flammability of ethylene-propylene-diene (EPDM) rubber composites. The hybrid filler systems showed technically promising synergetic effects on the performance of the EPDM composites. A pronounced reinforcing effect in EPDM composites filled with hybrid SiC filler systems was noted. Tensile strength increased in the systems with carbon black, silica, and graphene nanoplatelets, by 21%, 37%, and 68%, respectively, compared to the neat EPDM. Dynamic-mechanical analysis (DMA) revealed a shift of the glass transition temperature (Tg) of EPDM composites towards higher values following the incorporation of hybrid SiC fillers, indicating that the mobility of the macromolecule chains was restricted by the presence of filler particles. Importantly, the application of SiC as a filler in EPDM rubber composites contributed to a considerable reduction in flammability, as demonstrated by microscale combustion calorimetry (MCC). The most promising results were obtained for HAL/SiC and LDH/SiC hybrid systems, which produced final composites with high flame retardancy and good mechanical performance. The study highlights the significant potential of SiC and SiC hybrid systems as effective fillers improving the properties of elastomer composites. [ABSTRACT FROM AUTHOR]

In the cracking process of waste tires, pyrolysis carbon black (CBp), as a solid product, accounts for about 35% of the total tire rubber content. Here, the treated CBp has been gradually applied to the tire formula to improve the recycling efficiency of waste tires. This study elucidated the influence of adding CBp during the tire mixing process on soft friction and metal wear. Compared with industrial carbon black (I-CB), the friction coefficient of CBp was smaller at different mixing stages, and the ripple caused by adhesion friction was not evident. After the modified CBp (M-CBp) was obtained by implementing the surface activation of common CBp (C-CBp), the friction coefficient between M-CBp and metal increased by 10%, while the filler dispersion and comprehensive mechanical properties showed an upward trend. The wear rate of metal was higher than that observed after adding I-CB during the same mixing mode; thus, it was necessary to strengthen the wear resistance of the inner-wall surface of the mixing chamber. The –OH group on the M-CBp surface can also participate in the silane coupling reaction and aggravate the metal wear of the mixer chamber wall. Through a comparison of results, the mixing friction coefficient can reflect the strength of filler–rubber interaction, which in turn can preliminarily represent the dispersion effect and comprehensive properties, reveal the reason behind the poor performance of CBp, and highlight the need for modification from the perspective of tribology. [ABSTRACT FROM AUTHOR]

Shape-memory polymers tend to present rigid behavior at ambient temperature, being unable to deform in this state. To obtain soft shape-memory elastomers, composites based on a commercial rubber crosslinked by both ionic and covalent bonds were developed, as these materials do not lose their elastomeric behavior below their transition (or activation) temperature (using ionic transition for such a purpose). The introduction of fillers, such as carbon black and multiwalled carbon nanotubes (MWCNTs), was studied and compared with the unfilled matrix. By adding contents above 10 phr of MWCNT, shape-memory properties were enhanced by 10%, achieving fixing and recovery ratios above 90% and a faster response. Moreover, by adding these fillers, the conductivity of the materials increased from ~10−11 to ~10−4 S·cm−1, allowing the possibility to activate the shape-memory effect with an electric current, based on the heating of the material by the Joule effect, achieving a fast and clean stimulus requiring only a current source of 50 V. [ABSTRACT FROM AUTHOR]

In this work, we evaluated the processing and reinforcement characteristics of both carbon black (CB) and graphene nanoplatelets (GNPs) within a nitrile butadiene rubber (NBR) matrix. The aspect ratio of the GNPs was measured using atomic force microscopy (AFM) and related to the dispersion and agglomeration within the NBR matrix, as observed by scanning electron microscopy (SEM). The relationship between GNP aspect ratio and mechanical properties was studied by micromechanical modelling. The tensile and tear properties of NBR after compounding with GNPs were enhanced to a greater extent compared to carbon black, while curing times were smaller and scorch times longer, indicating some of the advantages of using GNPs. Overall, the inherent properties of GNPs along with their geometry led to the production of better-performing rubber compounds that can replace their CB-filled counterparts in applications where flexibility, tear strength and compliance are important. The influence of processing on dispersion, orientation and agglomeration of flakes was also highlighted with respect to the Young's modulus of the NBR compounds. [ABSTRACT FROM AUTHOR]

The influence of carbon black (CB) structure and surface area on key rubber properties such as monotonic stress-strain, cyclic stress–strain, and dynamic mechanical behaviors are investigated in this paper. Natural rubber compounds containing eight different CBs were examined at equivalent particulate volume fractions. The CBs varied in their surface area and structure properties according to a wide experimental design space, allowing robust correlations to the experimental data sets to be extracted. Carbon black structure plays a dominant role in defining the monotonic stress–strain properties (e.g., secant moduli) of the compounds. In line with the previous literature, this is primarily due to strain amplification and occluded rubber mechanisms. For cyclic stress–strain properties, which include the Mullins effect and cyclic softening, the observed mechanical hysteresis is strongly correlated with carbon black structure, which implies that hysteretic energy dissipation at medium to large strain values is isolated in the rubber matrix and arises due to matrix overstrain effects. Under small to medium dynamic strain conditions, classical strain dependence of viscoelastic moduli is observed (the Payne effect), the magnitude of which varies dramatically and systematically depending on the colloidal properties of the CB. At low strain amplitudes, both CB structure and surface area are positively correlated to the complex moduli. Beyond ~2% strain amplitude the effect of surface area vanishes, while structure plays an increasing and eventually dominant role in defining the complex modulus. This transition in colloidal correlations reflects the transition in stiffening mechanisms from flexing of rigid percolated particle networks at low strains to strain amplification at medium to high strains. By rescaling the dynamic mechanical data sets to peak dynamic stress and peak strain energy density, the influence of CB colloidal properties on compound hysteresis under strain, stress, and strain energy density control can be estimated. This has considerable significance for materials selection in rubber product development. [ABSTRACT FROM AUTHOR]

High loadings of carbon black (CB) are usually used to achieve the properties demanded of rubber compounds. In recent years, distinct nanoparticles have been investigated to replace CB in whole or in part, in order to reduce the necessary filler content or to improve performance. Multilayer graphene (MLG) is a nanoparticle made of just 10 graphene sheets and has recently become commercially available for mass-product nanocomposites. Three phr (part for hundred rubbers) of MLG are added to chlorine isobutyl isoprene rubber (CIIR)/CB composites in order to replace part of the CB. The incorporation of just 3 phr MLG triples the Young's modulus of CIIR; the same effect is obtained with 20 phr CB. The simultaneous presence of three MLG and CB also delivers remarkable properties, e.g. adding three MLG and 20 phr CB increased the hardness as much as adding 40 phr CB. A comprehensive study is presented, showing the influence on a variety of mechanical properties. The potential of the MLG/CB combination is illustrated to reduce the filler content or to boost performance, respectively. Apart from the remarkable mechanical properties, the CIIR/CB/MLG nanocomposites showed an increase in weathering resistance. [ABSTRACT FROM AUTHOR]

In this study, a new generalized regression neural network model for predicting the curing characteristics of rubber blends with different contents of carbon black filler cured at various temperatures is proposed for the first time The carbon black contents in the rubber blend and cure temperature were used as input parameters, while the minimum and maximum elastic torque, scorch time, and optimal cure time, obtained from the analysis of 11 rheological cure curves registered at 10 various temperatures, were considered as output parameters of the model. A special pre-processing procedure of the experimental input and target data and the training algorithm is described. Less than 55% of the experimental data were used to significantly reduce the total number of input and target data points needed for training the model. Satisfactory agreement between the predicted and experimental data, with a maximum error in the prediction not exceeding 5%, was found. It is concluded that the generalized regression neural network is a powerful tool for intelligently modelling the curing process of rubber blends even in the case of a small dataset, and it can find a wide range of practical applications in the rubber industry. [ABSTRACT FROM AUTHOR]

In this study, atomic force microscopy (AFM) nanomechanics were used to visualize the nanoscale stress distribution in carbon black (CB)-reinforced isoprene rubber (IR) vulcanizates at different elongations and quantitatively evaluate their volume fractions for the first time. The stress concentrations in the protofibrous structure (stress chains) that formed around the CB filler in CB-reinforced IR vulcanizates were directly observed at the nanoscale. The relationship between the local nanoscale stress distribution and macroscopic tensile properties was revealed based on the microscopic stress distribution and microscopic spatial structure. This study can help us gain insight into the microscopic reinforcement mechanism of carbon black-containing rubber composites. [ABSTRACT FROM AUTHOR]

Most rubbers used today rely on sulphur as a cross-linking agent and carbon black from fossil resources to modify the mechanical properties. A very promising substitute can be found in natural keratins such as feathers. These are not only tough, but also contain a relevant amount of sulphur in the form of disulphide bridges. The present study shows that these can be activated under vulcanisation conditions and then bind covalently to EPDM rubber to form a cross-linked network. Feathers were cut into lengths of 0.08, 0.2, and 1 mm and incorporated at 38, 69, or 100 phr into EPDM mixtures containing either no carbon black or no carbon black nor sulphur. The presence of feather cuttings increases the tensile and compressive strength as well as the hardness, and reduces the rebound resilience. Due to their high (approximately 17%) nitrogen content, the feathers also improve the thermal stability of the composite, as the main degradation step is shifted from 400 °C to 470 °C and the decomposition is significantly slowed down. Since elastomers are a large market and feathers in particular are a high-volume waste, the combination of these two offers enormous ecological and economic prospects. [ABSTRACT FROM AUTHOR]

Natural rubber is of significant economic importance owing to its excellent resilience, elasticity, abrasion and impact resistance. Despite that, natural rubber has been identified with some drawbacks such as low modulus and strength and therefore opens up the opportunity for adding a reinforcing agent. Apart from the conventional fillers such as silica, carbon black and lignocellulosic fibers, nanocellulose is also one of the ideal candidates. Nanocellulose is a promising filler with many excellent properties such as renewability, biocompatibility, non-toxicity, reactive surface, low density, high specific surface area, high tensile and elastic modulus. However, it has some limitations in hydrophobicity, solubility and compatibility and therefore it is very difficult to achieve good dispersion and interfacial properties with the natural rubber matrix. Surface modification is often carried out to enhance the interfacial compatibilities between nanocellulose and natural rubber and to alleviate difficulties in dispersing them in polar solvents or polymers. This paper aims to highlight the different surface modification methods employed by several researchers in modifying nanocellulose and its reinforcement effects in the natural rubber matrix. The mechanism of the different surface medication methods has been discussed. The review also lists out the conventional filler that had been used as reinforcing agent for natural rubber. The challenges and future prospective has also been concluded in the last part of this review. [ABSTRACT FROM AUTHOR]

Halloysite nanotubes (HNTs) are naturally occurring tubular clay made of aluminosilicate sheets rolled several times. HNT has been used to reinforce many rubbers. However, the narrow diameter of this configuration causes HNT to have poor interfacial contact with the rubber matrix. Therefore, increasing the distance between layers could improve interfacial contact with the matrix. In this work, Epoxidized Natural Rubber (ENR)/HNT was the focus. The HNT layer distance was successfully increased by a urea-mechanochemical process. Attachment of urea onto HNT was verified by FTIR, where new peaks appeared around 3505 cm−1 and 3396 cm−1, corresponding to urea's functionalities. The intercalation of urea to the distance gallery of HNT was revealed by XRD. It was also found that the use of urea-treated HNT improved the modulus, tensile strength, and tear strength of the composites. This was clearly responsible for interactions between ENR and urea-treated HNT. It was further verified by observing the Payne effect. The value of the Payne effect was found to be reduced at 62.38% after using urea for treatment. As for the strain-induced crystallization (SIC) of the composites, the stress–strain curves correlated well with the results from synchrotron wide-angle X-ray scattering. [ABSTRACT FROM AUTHOR]

According to specific formulas, the mixing of rubber samples occurs by two methods: open mixing and internal mixing. The effects of frequency, mixing process, carbon black (CB) content, zinc oxide (ZnO) content, and stearic acid (SA) content on the dielectric properties of rubber materials were studied. The results showed that the effects of the mixing process on the dielectric properties of the rubber samples cannot be ignored, and the appropriate mixing process should be selected when preparing the required rubber materials. The dielectric constant and loss factor of the rubber samples vary depending on the frequency. The dielectric constant had a peak and valley value, while the loss factor only had a peak. The dielectric constant and loss factor of rubber samples were significantly affected by the content of CB, ZnO, and SA. The peak frequency decreased with the increase in CB content, however, the dielectric constant increased with an increase in CB content. The higher the ZnO content, the lower the peak frequency. In addition, the dielectric constant and loss factor increased with an increase in ZnO content. The higher the SA content, the greater the peak frequency. In addition, the dielectric constant and loss factor decreased with an increase in SA content. It is hoped that the experimental results obtained can provide guidance for the study of the dielectric properties, microwave absorption properties, and microwave heating characteristics of rubber polymers. [ABSTRACT FROM AUTHOR]

This study investigates the impact of spent coffee biochar (Biochar) compared to carbon black (CB) as a partial replacement for carbon black in epoxidized natural rubber (ENR). Particle size and elemental analysis were used to characterize the biochar and CB. Cure characteristics, tensile, thermal, and morphological properties on the effect of biochar and CB as filler were studied. It was found that incorporating 10 phr of spent coffee biochar could improve the composites' tensile properties and thermal performance compared to carbon black. However, the addition of biochar significantly affects the maximum torque compared to CB and delays the vulcanization time. SEM study shows that biochar has a strong effect on the morphology of composite films. The FTIR graph reveals no substantial difference between compounds with biochar and CB. According to the thermal calorimetric study, the thermal stability of ENR-Biochar is higher than that of ENR-CB. Additionally, these findings suggest that the utilization of spent coffee as a sustainable biochar could be further explored, but little has been done in epoxidized natural rubber (ENR). [ABSTRACT FROM AUTHOR]

A comparative study focusing on the visco–elastic properties of two series of carbon black filled composites with natural rubber (NR) and its blends with butadiene rubber (NR-BR) as matrices is reported. Strain sweeps at different temperatures are performed. Filler network-related contributions to reinforcement ( Δ G ′ ) are quantified by the classical Kraus equation while a modified Kraus equation is used to quantify different contributions to dissipation ( Δ G D ″ , Δ G F ″ ). Results indicate that the filler network is visco-elastic in nature and that it is causing a major part of the composite dissipation at small and intermediate strain amplitudes. The temperature dependence of filler network-related reinforcement and dissipation contributions is found to depend significantly on the rubber matrix composition. We propose that this is due to differences in the chemical composition of the glassy rubber bridges connecting filler particles since the filler network topology is seemingly not significantly influenced by the rubber matrix for a given filler content. The underlying physical picture explains effects in both dissipation and reinforcement. It predicts that these glassy rubber bridges will soften sequentially at temperatures much higher than the bulk T g of the corresponding rubber. This is hypothetically due to rubber–filler interactions at interfaces resulting in an increased packing density in the glassy rubber related to the reduction of free volume. From a general perspective, this study provides deeper insights towards the molecular origin of reinforcement and dissipation in rubber composites. [ABSTRACT FROM AUTHOR]

A monotonous relation between strain and measured electric resistance is highly appreciated in stretchable elastomer sensors. In real-life application the voids or technological holes of strained samples often induce non-homogeneous local strain. The present article focused on studying the effect of non-homogeneous local strain on measured direct current (DC) effective electric resistance (EER) on samples of natural rubber (NR), reinforced with 50, 60 and 70 phr of carbon black (CB). Samples were imparted geometrical inhomogeneities to obtain varied local strains. The resulting strain distribution was analyzed using Digital Image Correlation (DIC). EER exhibited a well-detectable influence of locations of inhomogeneities. Expectedly, the EER globally decreased with an increase in CB loading, but showed a steady increase as a function of strain for 50 and 60 phr over the complete testing protocol. Interestingly, for 70 phr of CB, under the same testing conditions, an alternating trend in EER was encountered. This newly observed behavior was explained through a novel hypothesis—"current propagation mode switching phenomenon". Finally, experimentally measured EERs were compared with the calculated ones, obtained by summing the global current flow through a diversity of strain dependent resistive domains. [ABSTRACT FROM AUTHOR]

Rubber compounding with two or more components has been extensively employed to improve various properties. In particular, natural rubber (NR)/ethylene-propylene-diene monomer rubber (EPDM) blends have found use in tire and automotive parts. Diverse fillers have been applied to NR/EPDM blends to enhance their mechanical properties. In this study, a new class of mineral filler, phlogopite, was incorporated into an NR/EPDM blend to examine the mechanical, curing, elastic, and morphological properties of the resulting material. The combination of aminoethylaminopropyltrimethoxysilane (AEAPS) and stearic acid (SA) compatibilized the NR/EPDM/phlogopite composite, further improving various properties. The enhanced properties were compared with those of NR/EPDM/fillers composed of silica or carbon black (CB). Compared with the NR/EPDM/silica composite, the incompatibilized NR/EPDM/phlogopite composite without AEAPS exhibited poorer properties, but NR/EPDM/phlogopite compatibilized by AEAPS and SA showed improved properties. Most properties of the compatibilized NR/EPDM/phlogopite composite were similar to those of the NR/EPDM/CB composite, except for the lower abrasion resistance. The NR/EPDM/phlogopite/AEAPS rubber composite may potentially be used in various applications by replacing expensive fillers, such as CB. [ABSTRACT FROM AUTHOR]

In the present work, composite materials were prepared by incorporation of manganese-zinc ferrite, carbon black and combination of ferrite and carbon black into acrylonitrile-butadiene rubber (NBR). For cross-linking of composites, standard sulfur-based curing system was applied. The main goal was to investigate the influence of the fillers on the physical-mechanical properties of composites. Then, the electromagnetic absorption shielding ability was investigated in the frequency range 1 MHz–3 GHz. The results revealed that composites filled with ferrite provide sufficient absorption shielding performance in the tested frequency range. On the other hand, ferrite behaves as an inactive filler and deteriorates the physical-mechanical characteristics of composites. Carbon black reinforces the rubber matrix and contributes to the improvement of physical-mechanical properties. However, composites filled with carbon black are not able to absorb electromagnetic radiation in the given frequency range. Finally, the combination of carbon black and ferrite resulted in the modification of both physical-mechanical characteristics and absorption shielding ability of hybrid composites. [ABSTRACT FROM AUTHOR]

Research and development of nanocellulose and nanocellulose-reinforced composite materials have garnered substantial interest in recent years. This is greatly attributed to its unique functionalities and properties, such as being renewable, sustainable, possessing high mechanical strengths, having low weight and cost. This review aims to highlight recent developments in incorporating nanocellulose into rubber matrices as a reinforcing filler material. It encompasses an introduction to natural and synthetic rubbers as a commodity at large and conventional fillers used today in rubber processing, such as carbon black and silica. Subsequently, different types of nanocellulose would be addressed, including its common sources, dimensions, and mechanical properties, followed by recent isolation techniques of nanocellulose from its resource and application in rubber reinforcement. The review also gathers recent studies and qualitative findings on the incorporation of a myriad of nanocellulose variants into various types of rubber matrices with the main goal of enhancing its mechanical integrity and potentially phasing out conventional rubber fillers. The mechanism of reinforcement and mechanical behaviors of these nanocomposites are highlighted. This article concludes with potential industrial applications of nanocellulose-reinforced rubber composites and the way forward with this technology. [ABSTRACT FROM AUTHOR]

Adding carbon black (CB) particles to elastomeric polymers is essential to the successful industrial use of rubber in many applications, and the mechanical reinforcing effect of CB in rubber has been studied for nearly 100 years. Despite these many decades of investigations, the origin of stiffness enhancement of elastomers from incorporating nanometer-scale CB particles is still debated. It is not universally accepted whether the interactions between polymer chains and CB surfaces are purely physical adsorption or whether some polymer–particle chemical bonds are also introduced in the process of mixing and curing the CB-filled rubber compounds. We review key experimental observations of rubber reinforced with CB, including the finding that heat treatment of CB can greatly reduce the filler reinforcement effect in rubber. The details of the particle morphology and surface chemistry are described to give insights into the nature of the CB–elastomer interfaces. This is followed by a discussion of rubber processing effects, the influence of CB on crosslinking, and various chemical modification approaches that have been employed to improve polymer–filler interactions and reinforcement. Finally, we contrast various models that have been proposed for rationalizing the CB reinforcement of elastomers. [ABSTRACT FROM AUTHOR]

The ability of long-term thermo-oxidative resistance is very important for elastomers in application. However, many conventional antioxidants are difficult to realize the long-term thermo-oxidative resistance. To overcome this limitation, a design strategy is introduced by combing elastomers with MXene and natural rubber (NR) is chosen as a model material. MXene is efficient in absorbing oxygen and the generated free radicals in the NR matrix and can inhibit the diffusion of oxygen toward the interior. Moreover, MXene, like graphene and carbon black, absorbs molecular chains, inhibiting the migration of MXene toward the surface of the sample. Such characteristics of MXene endow NR/MXene with the long-term outstanding thermo-oxidative resistance. For example, after three days of the thermo-oxidative process for NR/MXene, the tensile strength is 19 MPa and the retention of tensile strength is 63%, which far exceeds the effects of conventional antioxidants. This work not only provides a good guide for the universal design of elastomers with long-term thermo-oxidative resistance but also expands the application of MXene. [ABSTRACT FROM AUTHOR]

The self-healing composites were prepared from the combination of bromobutyl rubber (BIIR) and natural rubber (NR) blends filled with carbon nanotubes (CNT) and carbon black (CB). To reach the optimized self-healing propagation, the BIIR was modified with ionic liquid (IL) and butylimidazole (IM), and blended with NR using the ratios of 70:30 and 80:20 BIIR:NR. Physical and chemical modifications were confirmed from the mixing torque and attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR). It was found that the BIIR/NR-CNTCB with IL and IM effectively improved the cure properties with enhanced tensile properties relative to pure BIIR/NR blends. For the healed composites, BIIR/NR-CNTCB-IM exhibited superior mechanical and electrical properties due to the existing ionic linkages in rubber matrix. For the abrasion resistances, puncture stress and electrical recyclability were examined to know the possibility of inner liner applications and Taber abrasion with dynamic mechanical properties were elucidated for tire tread applications. Based on the obtained Tg and Tan δ values, the composites are proposed for tire applications in the future with a simplified preparation procedure. [ABSTRACT FROM AUTHOR]

The main advantages of the use of silica instead of carbon black in rubber compounds are based on the use of a silane coupling agent. The use of a coupling agent to modify the silica surface improves the compatibility between the silica and the rubber. There are two different possibilities of modifying the silica surface by silane: ex-situ and in-situ. The present work studies the differences between these processes and how they affect the in-rubber properties of silica filled SBR compounds. [ABSTRACT FROM AUTHOR]

The effect of the strain rate on damage in carbon black filled Ethylene Propylene Diene Monomer rubber (EPDM)stretched during single and multiple uniaxial loading is investigated. This has been performed by analyzing the stress–strain response, the evolution of damage by Digital Image Correlation (DIC), the associated dissipative heat source by InfraRed thermography (IR), and the chains network damage by swelling. The strain rates were selected to cover the transition from quasi-static to medium strain rate conditions. In single loading conditions, the increase of the strain rate yields in a preferential damage of the filler network while the rubber network is preserved. Such damage is accompanied by a stress softening and an adiabatic heat source rise. Conversely, increasing the strain rate in cyclic loading conditions yields in a filler network accommodation and a high self-heating whose combined effect is proposed as a possible cause of the ability of filled EPDM to limit damage by reducing cavities opening during loading, and favoring cavities closing upon unloading. [ABSTRACT FROM AUTHOR]

The objective of this work is to study the influence of the ratio between the elastomer (EPDM) phase and the thermoplastic phase (PP) in thermoplastic vulcanizates (TPVs) as well as the associated morphology of the compression set of the material. First, from a study of the literature, it is concluded that the rubber phase must be dispersed with a large distribution of the domain size in the thermoplastic phase in order to achieve a high concentration, i.e., a maximal packing fraction close to ~0.80. From this discussion, it is inferred that a certain degree of progress in the crosslinking reaction must be reached when the thermoplastic phase is melted during mixing in order to achieve dispersion of the elastomeric phase in the thermoplastic matrix under maximum stress. In terms of elasticity recovery which is measured from the compression set experiment, it is observed that the crosslinking agent nature (DCP or phenolic resin) has no influence in the case of a TPV compared with a pure crosslinked EPDM system. Then, the TPV morphology and the rubber phase concentration are the first order parameters in the compression set of TPVs. Finally, the addition of carbon black fillers leads to an improvement of the mechanical properties at break for the low PP concentration (20%). However, the localization of carbon black depends on the crosslinking chemistry nature. With radical chemistry by organic peroxide decomposition, carbon black is located at the interface of EPDM and PP acting as a compatibilizer. [ABSTRACT FROM AUTHOR]