Search

Silica fillers are used in various nanocomposites in combination with silanes as a reinforcing filler. In tire technology, silica is generally functionalized before (pre-treated) or during mixing (in-situ silanization or post-treated). In both cases, a soft base catalyst (e.g., triethylamine or diphenyl guanidine, DPG) is typically used to accelerate and increase the yield of the silane/silica coupling reaction. In this study, we investigated how pre-treatments of silica particles with either strong amine or hydride bases impact the silanization of silica prior to or during SBR mixing for silica-rubber nanocomposite fabrication. Our findings are supported by molecular characterization (solid state 29Si NMR, 1H NMR and TGA), and scanning electron microscopy. In addition, the impact of these silica pre-treatments on a nanocomposite’s mechanical properties was evaluated using dynamic mechanical analysis (DMA).

A set of poly(isobornyl methacrylate)s (PIBOMA) having molar mass in the range of 26,000–283,000 g mol−1 was prepared either via RAFT process or using free radical polymerization. These linear polymers demonstrated high glass transition temperatures (Tg up to 201 °C) and thermal stability (Tonset up to 230 °C). They were further applied as reinforcing agents in the preparation of the vulcanized rubber compositions based on poly(styrene butadiene rubber) (SBR). The influence of the PIBOMA content and molar mass on the cure characteristics, rheological and mechanical properties of rubber compounds were studied in detail. Moving die rheometry revealed that all rubber compounds filled with PIBOMA demonstrated higher torque increase values ΔS in comparison with rubber compositions without filler, independent of PIBOMA content or molar mass, thus confirming its reinforcing effect. Reinforcement via PIBOMA addition was also observed for vulcanized rubbers in the viscoelastic region and the rubbery plateau, i.e. from −20 to 180 °C, by dynamic mechanical thermal analysis. Notably, while at temperatures above ~125 °C, ultra-high-molecular-weight polyethylene (UHMWPE) rapidly loses its ability to provide reinforcement due to softening/melting, all PIBOMA resins maintained their ability to reinforce rubber matrix up to 180 °C. For rubber compositions containing 20 phr of PIBOMA, both tensile strength and elongation at break decreased with increasing PIBOMA molecular weight. In summary, PIBOMA, with its outstanding high Tg among known poly(methacrylates), may be used in the preparation of advanced high-stiffness rubber compositions, where it provides reinforcement above 120 °C and gives properties appropriate for a range of applications.

The miscibility between two polymers such as rubbers and performance resins is crucial to achieve given targeted properties in terms of tire performances. To this aim, α-methylstyrene/styrene resin (poly(αMSt-co-St)) are used to modify the viscoelastic behavior of rubbers and to fulfill the requirements of the final applications. The initial aim of this work was to understand the influence of poly(αMSt-co-St) resins blended at different concentrations in a commercial styrene-butadiene rubber (SBR). Interestingly, while studying the viscoelastic properties of SBR blends with poly(αMSt-co-St), crosslinking of the rubber was observed under conditions where it was not expected to happen. Surprisingly, after the crosslinking reactions, the poly(αMSt-co-St) resin was irreversibly miscible with SBR at concentrations far above its immiscibility threshold. A detailed investigation involving characterization technics including solid state nuclear magnetic resonance led to the conclusion that poly(αMSt-co-St) is depolymerizing under heating and can graft onto the chains of SBR. It results in an irreversible compatibilization mechanism between the rubber and the resin.

In this work, a sustainable chemical process was developed through the Fischer esterification of Protobind® lignin, a wheat straw soda lignin, and phloretic acid, a naturally occurring phenolic acid. It aimed at increasing the reactivity of lignin by enhancing the number of unsubstituted phenolic groups via a green and solvent-free chemical pathway. The structural features of the technical and esterified lignins were characterized by complementary spectroscopic techniques, including 1H, 13C, 31P, and two-dimensional analysis. A substantial increase in p-hydroxyphenyl units was measured (+64%, corresponding to an increase of +1.3 mmol g−1). A full factorial design of the experiment was employed to quantify the impact of critical variables on the conversion yield. The subsequent statistical analysis suggested that the initial molar ratio between the two precursors was the factor predominating the yield of the reaction. Hansen solubility parameters of both the technical and esterified lignins were determined by solubility assays in multiple solvents, evidencing their high solubility in common organic solvents. The esterified lignin demonstrated a better thermal stability as the onset of thermal degradation shifted from 157 to 220 °C, concomitantly to the shift of the glass transition from 92 to 112 °C. In conclusion, the esterified lignin showed potential for being used as sustainable building blocks for composite and thermoset applications.

In the present work we report on the development of a novel and sustainable electrolyte based on chitin. Chitin biopolymer was carboxymethylated in simple, mild, and green conditions in order to fine-tune the final properties of the electrolyte. To this end, chitin was modified for various reaction times, while the molar ratio of the reagents, e.g., sodium hydroxide and monochloroacetic acid, was maintained fixed. The resulting chitin derivatives were characterized using various techniques. Under optimized conditions, modified chitin derivatives exhibiting a distinct degree of carboxymethylation and acetylation were obtained. Structural features, morphology, and properties are discussed in relation to the chemical structure of the chitin derivatives. For electrolyte applications, the ionic conductivity increased by three magnitudes from 10−9 S·cm−1 for unmodified chitin to 10−6 S·cm−1 for modified chitin with the highest degree of acetylation. Interestingly, the chitin derivatives formed free-standing films with and without the addition of up to 60% of ionic liquid, the ionic conductivity of the obtained solid electrolyte system reaching the value of 10−3 S·cm−1.

Polylactide (PLA) was blended by conventional and reactive extrusion with limonene (LM) or myrcene (My) as bio-based plasticizers. As-processed blends were carefully analyzed by a multiscale and multidisciplinary approach to tentatively determine their chemical structure, microstructure, thermal properties, tensile and impact behaviors, and hydrothermal stability. The main results indicated that LM and My were efficient plasticizers for PLA, since compared to neat PLA, the glass transition temperature was reduced, the ultimate tensile strain was increased, and the impact strength was increased, independently of the type of extrusion. The addition of a free radical initiator during the extrusion of PLA/LM was beneficial for the mechanical properties. Indeed, the probable formation of local branched/crosslinked regions in the PLA matrix enhanced the matrix crystallinity, the tensile yield stress, and the tensile ultimate stress compared to the non-reactive blend PLA/LM, while the other properties were retained. For PLA/My blends, reactive extrusion was detrimental for the mechanical properties since My polymerization was accelerated resulting in a drop of the tensile ultimate strain and impact strength, and an increase of the glass transition temperature. Indeed, large inclusions of polymerized My were formed, decreasing the available content of My for the plasticization and enhancing cavitation from inclusion-matrix debonding.