Search

With the increasing awareness of plastic pollution in the environment and the accumulation of microplastics in water, a significant amount of research and development is ongoing to replace the synthetic plastics in packaging and coatings. In this work, we explored the blends of carboxymethyl cellulose (CMC) and washed cottonseed meal (CSM, consisting mostly of cottonseed protein) as agro-based, biodegradable, and sustainable alternatives to plastics. Glycerol was found to be a suitable plasticizer for these blends. The blends of CMC/CSM were produced as single-layer films from 50 to 90 μm in thickness, consisting of different proportions of the components and plasticizer. The evaluated properties included opacity, water vapor permeability, mechanical properties, thermogravimetric analysis, moisture sorption analysis, and water swelling test. Higher percentages of CSM in the blend resulted in higher opacity and lower water vapor permeation rates. The mechanical strength waned with lower levels of CMC. Possible applications for these blends include their use as water-soluble food packaging and coatings and as dissolvable bags and pouches for detergents and agrochemicals.

This study investigates the unique morphology and mechanical properties of multi-jet electrospun cashew gum (CG) when combined with high-molecular-weight polyethylene oxide (PEO) and glycerol. Cashew gum (CG) is a low-cost, non-toxic heteropolysaccharide derived from Anacardium occidentale trees. Initially, the electrospinnability of aqueous solutions of cashew gum alone or in combination with PEO was evaluated. It was found that cashew gum alone was not suitable for electrospinning; thus, adding a small quantity of PEO was needed to create the necessary molecular entanglements for fiber formation. By using a single emitter with a CG:PEO ratio of 85:15, straight and smooth fibers with some defects were obtained. However, additional purification of the cashew gum solution was needed to produce more stable and defect-free straight and smooth fibers. Additionally, the inclusion of glycerol as a plasticizer was required to overcome material fragility. Interestingly, when the optimized formulation was electrospun using multiple simultaneous emitters, thicker aligned fiber bundles were achieved. Furthermore, the resulting oriented fiber mats exhibited unexpectedly high elongation at break under ambient conditions. These findings underscore the potential of this bio-polysaccharide-based formulation for non-direct water contact applications that demand elastic properties.

NMR analysis combined with statistical modeling offers a useful approach to investigate the microstructures of polymers. This article provides a selective review of the developments in both the NMR analysis of biobased polymers and the statistical models that can be used to characterize these materials. The information obtained from NMR and statistical models can provide insights into the microstructure and stereochemistry of appropriate biobased polymers and establish a systematic approach to their analysis. In suitable cases, the analysis can help optimize the synthetic procedures and facilitate the development of new or modified polymeric materials for various applications. Examples are given of the studies of poly(hydroxyalkanoates), poly(lactic acid), and selected polysaccharides, e.g., alginate, pectin, and chitosan. This article may serve as both a reference and a guide for future workers interested in the NMR sequence analysis of biobased materials.

Poly(lactic acid) (PLA) is a common biobased film-former made from renewable biomass, such as polysaccharides from sugarcane, corn, or cassava. It has good physical properties but is relatively expensive when compared to the plastics used for food packaging. In this work, bilayer films were designed, incorporating a PLA layer and a layer of washed cottonseed meal (CSM), an inexpensive agro-based raw material from cotton manufacturing, where the main component is cottonseed protein. These bilayer films were made through the solvent casting method. The combined thickness of the PLA/CSM bilayer film was between 47 and 83 μm. The thickness of the PLA layer in this film was 10%, 30%, or 50% of the total bilayer film’s thickness. Mechanical properties of the films, opacity, water vapor permeation, and thermal properties were evaluated. Since PLA and CSM are both agro-based, sustainable, and biodegradable, the bilayer film may be used as an eco-friendlier food packaging material, which helps reduce the environmental problems of plastic waste and microplastics. Moreover, the utilization of cottonseed meal may add value to this cotton byproduct and provide a potential economic benefit to cotton farmers.

There is current interest in replacing petroleum-based additives in consumer paper products with abundantly available, renewable and sustainable biopolymers such as lignin-containing cellulose nanofibers (LCNFs) and cottonseed protein. This research characterized the performance of cottonseed protein isolate with/without LCNFs to increase the dry strength of filter paper. The application of 10% protein solution with 2% LCNFs as an additive improved the elongation at break, tensile strength and modulus of treated paper products compared to the improved performance of cottonseed protein alone. Improvements in tensile modulus and tensile strength were greatest for samples containing larger amounts of lignin and a greater degree of polymerization than for those with less lignin from the same biomass sources.

Cotton is one of the most important and widely grown crops in the world. Understanding the synthesis mechanism of cotton fiber elongation can provide valuable tools to the cotton industry for improving cotton fiber yield and quality at the molecular level. In this work, the surface and thermal characteristics of cotton fiber samples collected from a wild type (WT) and three mutant lines (Li1, Li2-short, Li2-long, Li2-mix, and liy) were comparatively investigated. Microimaging revealed a general similarity trend of WT ≥ Li2-long ≈ Li2-mix > Li1 > Li2 short ≈ liy with Ca detected on the surface of the last two. Attenuated total reflectance Fourier transform infrared (ATR FT-IR) spectroscopy and thermogravimetric measurements also showed that Li2-short and liy were more similar to each other, and Li2-long and Li2-mix closer to WT while Li1 was quite independent. FT-IR results further demonstrated that wax and amorphous cellulose were co-present in fiber structures during the fiber formation processes. The correlation analysis found that the FT-IR-based maturity parameter was well correlated (p ≤ 0.05) to the onset decomposition temperature and all three weight-loss parameters at onset, peak, and end decomposition stages, suggesting that the maturity degree is a better parameter than crystallinity index (CI) and other FT-IR parameters that reflect the thermal stability of the cotton fiber. In summary, this work demonstrated that genetic mutation altered the surface and thermal characteristics in the same way for Li2-short and liy, but with different mechanisms for the other three mutant cotton fiber samples.

Xylan is a major type of hemicellulose that has attracted a lot of research and development activities. It is often derivatized in order to improve its properties. In the literature, hydrophobic modification of polymers is often used to produce surfactant-like materials and associative thickeners. In this work, we have derivatized xylan with alkyl ketene dimer (AKD) and two types of alkenyl succinic anhydrides (ASAs). The xylan-AKD derivatives have been made at 90 °C, using dimethyl sulfoxide as solvent and 4-dimethylaminopyridine as promoter. Samples with degrees of substitution (DS) up to 0.006 have been produced. The xylan-ASA derivatives have been synthesized at 120 °C in dimethyl sulfoxide with DS up to 0.105–0.135. The structures of these products have been confirmed with NMR and FT-IR. These xylan derivatives increase the structural diversity of xylan and provide additional options for people seeking to use hydrophobically modified polysaccharides in their applications.

Water washing of cottonseed meal is more cost-efficient and environmentally friendly than protein isolation by means of alkaline extraction and acidic precipitation. Thus, water-washed cottonseed meal (WCSM) is more promising as biobased wood adhesives. In this work, we examined the effects of the particle size on the morphology and adhesive performance of WCSM. Pilot-scale produced and dried WCSM was treated by three grinding methods: (1) ground by a hammer mill and passed through a 0.5-mm screen, (2) further ground by a cyclone mill and passed through a 0.5-mm screen, or (3) further ground by a ball mill and passed through a 0.18-mm screen. Micro-morphological examination revealed two types of particles. The filament-like particles were mainly fibrous materials from residual linters. Chunk-like particles were more like aggregates or accumulations of small particles, with proteins as the major component. Further grinding of the 0.5-mm Hammer product with the Cyclone and Ball mill led to more fine (smaller) particles in the WCSM products. The impact of further grinding on the dry and soaked adhesive strengths was minimal. However, the decrease of the hot and wet strengths of WCSM products by the additional grinding was significant (p ≤ 0.05). Data presented in this work is useful in developing the industrial standards of WCSM products used in wood bonding.