Search

We describe a compact, all fiber, frequency stabilized diode laser system at 2051 nm using CO

The modal content of 7 and 19 cell Kagomé anti resonant hollow core fibers (K-ARF) with hypocycloid core surrounds is experimentally investigated through the spectral and spatial (Ssup2/sup) imaging technique. It is observed that the 7 and 19 cell K-ARF reported here, support 4 and 7 LP mode groups respectively, however the observation that K-ARF support few mode groups is likely to be ubiquitous to 7 and 19 cell K-ARFs. The transmission loss of the higher order modes (HOMs) was measured via Ssup2/supand a cutback method. In the 7 cell K-ARF it is found that the LPsub11/suband LPsub21/submodes have approximately 3.6 and 5.7 times the loss of the fundamental mode (FM), respectively. In the 19 cell it is found that the LPsub11/submode has approximately 2.57 times the loss of the FM, while the LPsub02/submode has approximately 2.62 times the loss of the FM. Additionally, bend loss in these fibers is studied for the first time using Ssup2/supto reveal the effect of bend on modal content. Our measurements demonstrate that K-ARFs support a few mode groups and indicate that the differential loss of the HOMs is not substantially higher than that of the FM, and that bending the fiber does not induce significant inter modal coupling. A study of three different input beam coupling configurations demonstrates increased HOM excitation at output and a non-Gaussian profile of the output beam if poor mode field matching is achieved.

We describe a compact, all fiber, frequency stabilized diode laser system at 2051 nm using CO2 gas-filled Kagome Hollow Core Fiber (HCF), capable of tuning continuously over four transitions in12C16O2: R(24), R(26), R(28), and R(30). This laser system has been designed for use in future space-based atmospheric monitoring using differential absorption lidar (DIAL). The fully spliced Kagome HCF gas cell is filled to 2 kPa CO2 partial pressure and we compare the observed CO2 lineshape features with those calculated using HITRAN, to quantify the properties of the CO2-filled fiber cell. In this first demonstration of Kagome HCF used in a fully sealed gas cell configuration for spectroscopy at 2 µm, we characterize the frequency stability of the locked system by beat frequency comparison against a reference laser. Results are presented for the laser locked to the center of the12C16O2 R(30) transition, with frequency stability of ∼40 kHz or better at 1 s, and a frequency reproducibility at the 0.4-MHz level over a period of > 1 month. For DIAL applications, we also demonstrate two methods of stabilizing the laser frequency ∼3 GHz from this line. Furthermore, no pressure degradation was observed during the ∼15-month period in which frequency stability measurements were acquired.

We report a novel approach to reconstruct the cross-sectional profile of fabricated hollow-core photonic bandgap fibers from scanning electron microscope images. Finite element simulations on the reconstructed geometries achieve a remarkable match with the measured transmission window, surface mode position and attenuation. The agreement between estimated scattering loss from surface roughness and measured loss values indicates that structural distortions, in particular the uneven distribution of glass across the thin silica struts on the core boundary, have a strong impact on the loss. This provides insight into the differences between idealized models and fabricated fibers, which could be key to further fiber loss reduction.

Specialty optical fibers, in particular microstructured and multi-material optical fibers, have complex geometry in terms of structure and/or material composition. Their fabrication, although rapidly developing, is still at a very early stage of development compared with conventional optical fibers. Structural characterization of these fibers during every step of their multi-stage fabrication process is paramount to optimize the fiber-drawing process. The complexity of these fibers restricts the use of conventional refractometry and microscopy techniques to determine their structural and material composition. Here we present, to the best of our knowledge, the first nondestructive structural and material investigation of specialty optical fibers using X-ray computed tomography (CT) methods, not achievable using other techniques. Recent advances in X-ray CT techniques allow the examination of optical fibers and their preforms with sub-micron resolution while preserving the specimen for onward processing and use. In this work, we study some of the most challenging specialty optical fibers and their preforms. We analyze a hollow core photonic band gap fiber and its preforms, and bond quality at the joint between two fusion-spliced hollow core fibers. Additionally, we studied a multi-element optical fiber and a metal incorporated dual suspended-core optical fiber. The application of X-ray CT can be extended to almost all optical fiber types, preforms and devices.

A silicon microstructured fiber has been designed and fabricated using a pure silica photonic bandgap guiding fiber as a 3D template for materials deposition. The resulting silicon fiber has a micron sized core but with a small core-cladding index contrast so that it only supports two guided modes. It will be shown that by using the microstructured template this fiber exhibits a number of similar guiding properties to the more traditional index guiding air-silica structures. The large mode areas and low optical losses measured for the silicon microstructured fiber demonstrate its potential to be integrated with existing fiber infrastructures.

Micro-channels were fabricated in hollow-core photonic bandgap fiber (HC-PBGF) and suspended-core holey fiber (SC-HF) by femtosecond Ti:sapphire laser irradiation. Gaseous access was demonstrated via these engineered ports to the core of HC-PBGF and the hollow cladding of SC-HF. Femtosecond laser micro-machining caused no additional transmission loss in HC-PBGFs. This allowed a novel gas cell to be produced, in which gaseous access was provided solely through two micro-channels. Acetylene diffusion was also confirmed through a micro-channel leading to a single cladding airhole in SC-HF. This further highlighted the fabrication technique's precision, selectivity, and potential for developing fiber-based micro-fluidic devices.

The operational bandwidth of hollow-core photonic bandgap fibers (PBGFs) is drastically affected by interactions between the fundamental core mode and surface modes guided at the core-cladding interface. By systematically studying realistic hollow-core PBGFs we identify a new design regime robust in eliminating the presence of surface modes. We present new fiber designs with a fundamental core mode free of anticrossings with surface modes at all wavelengths within the bandgap, allowing for a low-loss operational bandwidth of ~ 17% of the central gap wavelength.

We present a novel method to validate the relative amount of power carried by high order modes in a multimode fiber using a Spatial and Spectral (S(2)) imaging technique. The method can be utilized to calibrate the S(2) set-up and uses Fresnel reflections from a thin glass plate to compare theoretical values with experimental results. We have found that, in the most general case, spectral leakage and sampling errors can lead S(2) to underestimate the multipath interference (MPI) of high order modes by several decibels, thus significantly impairing the result of the measurement. On the other hand, by applying suitable corrections as described in this work, we demonstrate that the S(2) produces MPI estimates that are accurate to within 1dB or better.

We show for the first time 100 Gbit/s total capacity at 2 µm waveband, using 4 × 9.3 Gbit/s 4-ASK Fast-OFDM direct modulation and 4 × 15.7 Gbit/s NRZ-OOK external modulation, spanning a 36.3 nm wide wavelength range. WDM transmission was successfully demonstrated over 1.15 km of low-loss hollow core photonic bandgap fiber (HC-PBGF) and over 1 km of solid core fiber (SCF). We conclude that the OSNR penalty associated with the SCF is minimal, while a ~1-2 dB penalty was observed after the HC-PBGF probably due to mode coupling to higher-order modes.

We report on a method to obtain dispersion measurements from spectral-domain low-coherence interferograms which enables high accuracy (≈ ps/(nm · km)), broadband measurements and the determination of very dense (up to 20 points/nm over 500 nm) data sets for both dispersion and dispersion slope. The method exploits a novel phase extraction algorithm which allows the phase associated with each sampling point of the interferogram to be calculated and provides for very accurate results as well as a fast measurement capability, enabling close to real time measurements. The important issue of mitigating the measurement errors due to any residual dispersion of optical elements and to environmental fluctuations was also addressed. We performed systematic measurements on standard fibers which illustrate the accuracy and precision of the technique, and we demonstrated its general applicability to challenging problems by measuring a carefully selected set of microstructured fibers: a lead silicate W-type fiber with a flat, near-zero dispersion profile; a hollow core photonic bandgap fiber with strongly wavelength dependent dispersion and dispersion slope; a small core, highly birefringent index guiding microstructured fiber, for which polarization resolved measurements over an exceptionally wide (≈ 1000 nm) wavelength interval were obtained.

We experimentally demonstrate phase regeneration of a 40-Gb/s differential phase shift keying (DPSK) signal in a 1.7-m long highly nonlinear lead silicate W-type fiber using a degenerate two-pump phase-sensitive amplifier (PSA). Results show an improvement in the Error Vector Magnitude (EVM) and a reduction of almost a factor of 2 in the phase noise of the signal after regeneration for various noise levels at the input.

We experimentally demonstrate phase-sensitive amplification in a highly nonlinear and low-dispersion lead-silicate W-type fiber. A phase-sensitive gain variation of 6 dB was observed in a 1.56-m sample of the fiber for a total input pump power of 27.7 dBm.

Selective excitation of whispering-gallery and bottle modes in a robust hollow-bottle optical microresonator, fabricated from a silica microcapillary by a pressure-compensated, “soften-and-compress” method, is demonstrated. Characteristic resonance spectra of bottle modes were obtained by using a tapered fiber coupled at different locations along the hollow bottle. The spectral characteristics (Q-factor, excitation efficiency) are shown to have high tolerance to angular misalignment of the tapered fiber. In addition, introduction of localized losses on the outer surface of the resonator results in selective clean-up of the transmission spectrum and superior performance. A theoretical analysis of modal turning points and associated resonant wavelengths is used to explain the mechanism of mode-suppression and the resultant spectral cleaning.

We investigate a novel approach to obtain highly nonlinear fibers with a tailored group velocity dispersion around a desired wavelength region of interest. Rather than exploiting longitudinal holes to control the average refractive index of the cladding and hence the fiber's waveguide dispersion, as in holey fibers, we propose using an all-solid cladding with a suitably chosen refractive index difference relative to the core. We demonstrate numerically that this solution allows a large freedom in the manipulation of the overall fiber dispersive properties, while enabling, in practice, a much more accurate control of the fiber's structural properties during fabrication. Effectively single mode guidance over a broad wavelength range can be achieved through the use of a second outer cladding forming a W-type index profile. We derive simple design rules for dispersion controlled fibers, based on which an algorithm for the automatic dispersion optimization is proposed, implemented and used to design various nonlinear fibers for all-optical processing and supercontinuum generation. Fabrication of a lead silicate fiber with flattened dispersion at telecoms wavelengths confirms the potential of these new fibers.

We report the design, fabrication and characterization of a lead silicate glass highly nonlinear W-type fiber with a flattened and near-zero dispersion profile in the 1.55 µm region. The fiber was composed of three types of commercial lead silicate glasses. Effectively single-mode guidance was observed in the fiber at 1550nm. The nonlinear coefficient and the propagation loss at this wavelength were measured to be 820 W-1km-1 and 2.1dB/m, respectively. Investigations of the Brillouin threshold revealed no evidence of stimulated Brillouin scattering for continuous wave signal powers up to 29dBm in a 2m sample of the fiber. A broadband dispersion measurement confirmed the near-zero dispersion values and the flat dispersion profile around 1550nm, in good agreement with our simulations. Efficient four-wave-mixing, tunable across the whole C-band, was demonstrated in a 2.2m length of the fiber.

The long interaction pathlengths provided by hollow-core photonic bandgap fibers (HC-PBFs) are especially advantageous for the detection of weakly absorbing gases such as methane (CH(4)). In this paper, we demonstrate methane sensing with a 1670-nm band HC-PBF. A multiline algorithm is used to fit the R(6) manifold (near 1645 nm) and, in this way, to measure the gas concentration. With this method, a minimum detectivity of 10 ppmv for the system configuration was estimated.

We study the modal properties of feasible hollow-core photonic bandgap fibers (HC-PBGFs) with cores formed by omitting either 7 or 19 central unit-cells. Firstly, we analyze fibers with thin core surrounds and demonstrate that even for large cores the proposed structures are optimum for broad-band transmission. We compare these optimized structures with fibers which incorporate antiresonant core surrounds which are known to have low-loss. Trade-offs between loss and useful bandwidth are presented. Finally, we study the effects that small modifications to the core surround have on the fiber's group velocity dispersion, showing the possibility of engineering the dispersion in hollow-core photonic bandgap fibers.

We report the generation of white light from a picosecond pump by efficient four-wave mixing processes. A 530 nm green source based on a frequency-doubled Yb-doped fiber laser generates strong red and blue sidebands in the secondary cores of a holey fiber with large air-filling factor. Phase matching is attributed to birefringence within the submicrometer-sized secondary cores induced by non-symmetric deformation during the fiber drawing.