Search

Extreme lasers capable of short, high-energy pulses are probing the frontiers of science and advancing practical technology. The utility of such lasers increases with their average power delivery, which enables faster data acquisition, higher flux of laser-driven particle and radiation sources and more efficient material processing. However, the same extreme energies and electric field strengths of these lasers are currently preventing their direct and high accuracy measurement for these experimental applications. To overcome this limitation, we use the momentum of the laser pulses as a measurement proxy for their energy. When light reflects from an ideal mirror, its momentum is transferred to the mirror, but its energy is reflected. We demonstrate here a force-sensing mirror configuration to measure laser pulse energies up to 100 J/pulse (10 ns duration, 10 Hz repetition rate) from a kilowatt-level average power multi-slab laser operated at the HiLASE facility of the Czech Academy of Sciences. We combine a radiation-pressure power meter with a charge integrator photodiode to form what we refer to as a Radiation Pressure Energy Meter. To our knowledge, this is the first demonstration of a high-accuracy, non-absorbing, SI traceable primary standard measurement of both single and average pulse energies of a 1-kW-average-power pulsed laser source. With this, we demonstrate a practical method for in-situ calibration of the traditional thermal instruments (pyroelectric detectors) currently used for indirect measurements of energy and power of such extreme lasers.

We have developed a planar absolute radiometer for room temperature (PARRoT) that will replace the legacy C-series calorimeter as the free-space continuous-wave laser power detector standard at the National Institute of Standards and Technology (NIST). This instrument will lower the combined relative expanded measurement uncertainty (k = 2) from 0.84 % to 0.13 %. PARRoT's performance was validated by comparing its response against a transfer standard silicon trap detector traceable to NIST's primary standard laser optimized cryogenic radiometer (LOCR) and against the C-series calorimeter. On average, these comparisons agreed to better than 0.008 % and 0.05 %, respectively.

We demonstrate the capability to measure the absolute power responsivity of optical fiber-coupled detectors at an expanded uncertainty of 0.1%, by direct comparison with a cryogenic primary standard. To facilitate synchronous power measurements, commercial all-fiber beam-splitters direct laser diode light simultaneously to the device under test and the primary standard. We investigate the use of single-mode, polarisation maintaining, and photonic crystal fibers to access the cryogenic standard, and report a reduction in the temperature dependent effective refractive index of these fibers of 0.1%, 0.15% and 0.3% respectively in going from room temperature to 5 K. We also evaluate the polarisation dependent loss of the beam-splitters, the stability of the beam-splitter ratio between the cryogenic detector and the device under test and the temporal and modal stability of the Fabry-Pérot laser diode sources. It is shown that the stability of the optical fiber beam-splitters limits the overall performance of the measurement system to an expanded uncertainty of 0.1%.

We present a small power meter that detects the radiation pressure of an incident high-power laser. Given its small package and non-destructive interaction with the laser, this power meter is well suited to realizing a robust real-time, high-accuracy power measurement in laser-based manufacturing environments. The incident laser power is determined through interferometric measurement of displacement of a 20 mm diameter high reflectivity mirror, mounted at the center of a dual element spiral flexure. This device can measure laser power from 25 W to 400 W with a 260 m W / H z noise floor and ≤ 3.2% expanded uncertainty. We validate our device against a calibrated thermopile with simultaneous measurements of an unpolarized 1070 nm laser and report good agreement between the two systems. Finally, by referencing to an identical mechanical spring that does not see the incident laser, we suppress vibration noise in the power measurement by 14.8 dB over a 600 Hz measured bandwidth. This is an improvement over other radiation pressure based power meters that have previously been demonstrated.

In recent years several ways to radiometrically calibrate optical fiber-coupled detectors have been developed. However, fiber-coupled calibration methods for single photon detectors have not been compared by national metrology institutes in order to validate their equivalence or traceability to the international systems of units yet.. Here, we present the comparison of radiometric calibration methods traceable to a NIST cryogenic radiometer at the 'few-photon' level. The calibration methods are based on metrology grade optical power meters. The expanded (k = 2) relative standard uncertainties of the calibration methods for the detection efficiency are of the order of 0.5%. However, the results changed relatively by 10% with a different set of optical fibers and mating connectors. These results stress the importance of fiber-core dimensions and fiber-connector repeatability.