Search

In detailed previous work by the authors, an innovative decay heat removal (DHR) system has been proposed and designed for the Integral Inherently Safe Light Water Reactor (I2S-LWR). The current paper studies the inadvertent actuation of one DHR system train during I2S-LWR normal operation due to a false signal or operator action. The RELAP5 code is used to perform a one-dimensional study, and important thermal-hydraulic characteristics, including primary loop coolant flow rate, pressure, temperature, DHR primary-side flow rate, and coolant temperature, are achieved during this transient. Then, a detailed computational fluid dynamics simulation utilizing STARCCM+ is carried out to investigate the coolant mixing characteristics in the downcomer and lower plenum and obtain the local thermal-hydraulic conditions at the reactor core inlet. It is found that as a consequence of inadvertent DHR actuation, the maximum overcooling at the reactor core inlet is about 3 K, which would not result in significant reactivity insertion. Furthermore, a more severe transient of inadvertent DHR operation with intermediate loop break is studied, and the results show that this would not lead to more significant overcooling to the I2S-LWR core compared with inadvertent DHR operation without intermediate loop break. This work is an indispensable supplement for DHR system comprehensive assessment in the I2S-LWR project. [ABSTRACT FROM AUTHOR]

Countercurrent flow limitation (CCFL) may occur under certain flow conditions in the surge line, restricting the draining of water from the pressurizer and thus affecting the coolant inventory and water level in the reactor pressure vessel (RPV). The complexity of the AP1000 pressurizer surge line structure makes predicting CCFL fairly difficult, and there are still not enough CCFL studies on this complex structure. Based on an extensive literature survey, the authors of this paper are particularly aware of the need for improved CCFL models for the pressurizer surge line of AP1000. To investigate the CCFL phenomenon in the surge line assembly fixture of AP1000, a whole-visual test model of the surge line is designed with a scaling ratio of 1:4, and a test loop is established to carry out visualization experiments with air-water countercurrent flow (CCF). The whole-visual test section made of acrylic material is composed of a pressurizer simulator, a surge line tube, a hot leg T-type tube, and an RPV simulator. The air-water CCF experiments are conducted at atmospheric pressure and room temperature with the pressurizer simulator water level varying from 150 to 900 mm. The visual CCF experimental processes and CCFL phenomena are filmed by a high-speed camera and analyzed in detail. The pressure drops at different CCFL locations are measured and evaluated to explore the relationships between the CCFL characteristics and flow patterns in the surge line. The development process of the CCFL is defined as the CCFL region, which can be divided into different regions according of the changes in water mass flow and CCF flow behavior. The CCFL data are analyzed and compared using the air and water superficial velocities to study the effects of hysteresis and water level. Small discrepancies are found between the data of different water levels, reflecting the small but not-negligible influence of the upper tank water level. Empirical models for the CCFL in the surge line assembly fixture are explored preliminarily using Kutateladze-type correlation and Froude-Ohnesorge correlation. Deficiencies still exist in the present semiempirical models, inspiring a more in-depth study on the empirical models for CCFL in the surge line assembly fixture that considers the complex two-phase flow behaviors in the upper tank and near the joint between the upper tank and surge line tube. The present CCFL data are compared broadly and in detail with groups of CCFL data of similar former experiments to demonstrate the applicability of the present air-water CCFL data to the development of a CCFL prediction model for the prototype large-diameter surge line assembly fixture of the AP600/AP1000. We will perform much more experimental and theoretical work to study the detailed mechanism of these special phenomena and to develop a more applicable CCFL model for the geometry and conditions of the prototype large-diameter surge line assembly fixture. [ABSTRACT FROM AUTHOR]

The technology for the 20-MW(thermal) Transportable Fluoride Salt-Cooled High-Temperature Reactor (TFHR) is proposed by Massachusetts Institute of Technology for off-grid applications such as Antarctic bases and remote mining sites. The preliminary thermal-hydraulic analyses and improvements based on a 1/12th full-core model were performed using three-dimensional computational fluid dynamics (CFD). A benchmark study was conducted by comparing the CFD results against empirical correlations and experimental data obtained by Cooke, Silverman, and Grele. In the 1/12th full-core analysis, three practical considerations that may challenge the TFHR temperature limits are evaluated as bounding analysis. These include (1) helium gap between fuel compact and graphite block, (2) thermal conductivity degradations of graphite matrix due to neutron irradiation, and (3) full-core scale power distribution obtained from neutronic calculations. These design considerations lead to insufficient margin between the normal operating condition and the predefined thermal limits. In this context, additional design features are implemented to improve the thermal-hydraulic safety of the TFHR. First, bypass flow in the interstitial gaps between the active core and the reflector is found capable of reducing the temperature peaks at the core periphery. Second, improvements of the flow distribution from the central downcomer to individual coolant channels enable a higher mass flow rate to the regions with compromised cooling access. Overall, thermal-hydraulic performance was significantly improved with a fuel temperature margin from 10 to 150 K and a coolant temperature margin from 16 to 160 K, as well as the more uniform temperature distribution across the reactor core. Furthermore, thermal-hydraulic safety can be maintained at a 20% overpower operating condition [i.e., 24 MW(thermal)]. Overall, this study provides an engineering basis for the TFHR thermal-hydraulic design to improve its safety margin. [ABSTRACT FROM AUTHOR]