Search

Abstract Scanning laser Doppler vibrometry (SLDV) is a promising method for visualizing defects in plate-like structures. The Lamb wave-based SLDV method using continuous excitations has been recently developed in nondestructive evaluation (NDE). In addition, various signal processing techniques have been developed to enhance damage detection capability for the method. To visualize defects, the A 0 mode is commonly used because of its sensitivity to the thickness variations, i.e. the wave speed changes according to the thickness of a plate. The A 0 mode is easily generated by lead zirconate titanate (PZT) transducers. However, for thick plates, the A 0 mode is found to be less sensitive to thickness variations compared to thin structures. To address this issue, a mode-tuned inter-digital transducer (IDT) is adopted to efficiently generate and utilize the symmetric modes for damage detection and visualization of thick plates. Based on the wavelength of the S 0 mode using the dispersion curve of the plate, the IDT is designed and fabricated for efficient symmetric mode generation. To evaluate the capability of the mode-tuned IDT-based SLDV, a 6-mm-thick plate (40 mm × 40 mm) with defects of 0.3 mm, 0.6 mm, 0.9 mm, and 1.2 mm depths is used. The S 0 mode is selected for its wavenumber sensitivity and the degree of separation between modes. It is demonstrated that the detectability of shallow defects in a thick plate is improved compared to that when using the A 0 mode. [ABSTRACT FROM AUTHOR]

This paper presents a multipath exploitation approach for defect imaging in thin-walled structures using Lamb waves under the sparse reconstruction framework. An image of the defects in the region of interest is obtained by inverting a multipath propagation model via group sparse reconstruction. This permits accurate imaging of regions close to the structure boundary without the introduction of ‘false’ defects or ghosts. Real-data measurements of defects close to the edge of an aluminum plate are used to demonstrate the effectiveness of the multipath exploitation scheme. [ABSTRACT FROM AUTHOR]

In engineering practice, failures due to fatigue cracks in metallic structures have always been difficult to predict. In our study, nonlinear Lamb wave-mixing was applied in the detection of micro-cracks in plates. The analysis of the nonlinear interaction of these waves with cracks of various lengths and widths was performed using finite-element simulations. The simulation results showed that the sideband at the sum frequency provide a sensitive means for micro-crack detection. Moreover, the sideband amplitudes show a monotonic increase with micro-crack length, but a decrease with micro-crack width. Experiments using Lamb wave-mixing were conducted on plates with fatigue cracks. The experimental results show that a proposed acoustic nonlinearity parameter related to the sideband at the sum frequency is sensitive to micro-cracks in plate, and is well correlated with the damage degree. [ABSTRACT FROM AUTHOR]

The developed method is based on acoustic underwater scattering measurements and can be applied to characterize a defect in a blade of a marine current turbine. To simplify the study, the blade is replaced by a rectangular plate immersed in water having a groove opening out. The measurements are made on horizontal plane perpendicular to the long axis of the stainless steel plate. The frequency range of signal is between 50 and 400kHz. The transducer is remote from the plate. The measurements are recorded on 360° with a 1° step. The experimental trajectories of the scattering signals are compared to the trajectories calculated from the group velocities of Lamb waves A and S 0. Spectra give also an information on groove position. The present study is the first step toward remote monitoring of blades on a marine current turbine. [ABSTRACT FROM AUTHOR]

Abstract: Several Lamb wave modes can be coupled to a particular structure, depending on its geometry and transducer used to generate the guided waves. Each Lamb mode interacts in a particular form with different types of defects, like notches, delamination, surface defects, resulting in different information which can be used to improve damage detection and characterization. An image compounding technique that uses the information obtained from different propagation modes of Lamb waves for non-destructive testing of plate-like structures is proposed. A linear array consisting of 16 piezoelectric elements is attached to a 1mm thickness aluminum plate, coupling the fundamental A0 and S0 modes at the frequencies of 100kHz and 360kHz, respectively. For each mode two images are obtained from amplitude and phase information: one image using the Total Focusing Method (TFM) and one phase image obtained from the Sign Coherence Factor (SCF). Each TFM image is multiplied by the SCF image of the respective mode to improve contrast and reduce side and grating lobes effects. The high dispersive characteristic of the A0 mode is compensated for adequate defect detection. The information in the SCF images is used to select one of the TFM mode images, at each pixel, to obtain the compounded image. As a result, dead zone is reduced, resolution and contrast are improved, enhancing damage detection when compared to the use of only one mode. [Copyright &y& Elsevier]

Abstract: The thermal degradation in ferritic Cr–Ni alloy steel plates is measured using the nonlinear effect of Lamb wave propagation. Experiments were carried out to introduce controlled levels of thermal damage to determine the nonlinear response of Lamb waves. A “mountain-shape” change in the normalized acoustic nonlinearity of Lamb wave versus the level of thermal degradation in the specimens has been observed. The variation in the measured acoustic nonlinearity reveals, based on metallographic studies, that the normalized acoustic nonlinearity increases due to the second phase precipitates in the early stage and it decreases as a combined result of dislocation change and micro-void initiation in the material. The results show a potential application of the nonlinear Lamb waves for the quantitative assessment of thermal damage in metallic plates or pipes. [Copyright &y& Elsevier]

Abstract: In this paper we propose a concept and report experimental results based on a circular array of Piezoelectric Wafer Active Sensors (PWASs) for rapid localization and parametric identification of corrosion type damage in metallic plates. Implementation of this circular array of PWASs combines the use of ultrasonic Lamb wave propagation technique and an algorithm based on symmetry breaking in the signal pattern to locate and monitor the growth of a corrosion pit on a metallic plate. Wavelet time-frequency maps of the sensor signals are employed to obtain an insight regarding the effect of corrosion growth on the Lamb wave transmission in time-frequency scale. We present here a method to eliminate the time scale, which helps in identifying easily the signature of damage in the measured signals. The proposed method becomes useful in determining the approximate location of the damage with respect to the location of three neighboring sensors in the circular array. A cumulative damage index is computed from the wavelet coefficients for varying damage sizes and the results appear promising. Damage index is plotted against the damage parameters for frequency sweep of the excitation signal (a windowed sine signal). Results of corrosion damage are compared with circular holes of various sizes to demonstrate the applicability of present method to different types of damage. [Copyright &y& Elsevier]

Abstract: This paper deals with developing a parametric 2D finite-element technique, which can size strip-like defects in elastic or viscoelastic, isotropic or anisotropic material plates. A pure incident Lamb wave mode is sent towards the defect and reflection and transmission coefficients produced by mode conversion phenomenon are used as input data for the inversion process, which consists in quantifying two unknown parameters representing the geometry of the defect. A finite-element-based model is used to simulate the Lamb wave scattering for various values of the aimed parameters, and specific post-processing based on Shkerdin’s orthogonality relation is applied to predict the needed reflection and transmission coefficients. The target is known reflection and transmission coefficients initially obtained from an experiment, which can be either a numerical experiment for validation purposes, or proper measurements on a sample for NDE application purposes. The inversion process is stopped when the predicted reflection and transmission coefficients fit at best those obtained from initial experiment. In this paper, we have quantified two geometrical parameters for three types of defects in different waveguides: the through-thickness depth (or position) and width (or radius) of (1) a circular hole inside an aluminium plate, (2) a rectangular notch at the surface of a Perspex plate, (3) a cracked zone inside a composite plate, representing an impact damage. [Copyright &y& Elsevier]

Abstract: In recent years, much attention has been paid to the use of Lamb waves for structural health monitoring. This choice is prompted by the high speed of Lamb wave inspection, although their dispersive nature can complicate the interpretation of results, especially when dealing with closely-spaced reflectors. In this paper, the objective is to improve the time resolution and signal-to-noise ratio of signals obtained from inspection of plates by the S 0 Lamb mode. The signal processing scheme used is based on deconvolution of the measured signal by Wiener filtering, followed by autoregressive spectral extrapolation. The deconvolution technique is applied to signals obtained from finite element models and also to experimentally measured signals; both sets of data are based on plates with various types of notch discontinuities. Using this technique, the separation distance between adjacent notches was estimated with high accuracy in both simulated and experimental ultrasonic signals. [ABSTRACT FROM AUTHOR]

Abstract: To investigate the propagation behavior of Lamb waves in a thermal stress relaxation type functionally graded material (FGM) plate with material parameters that vary continuously along the thickness, the power series technique, which has been proved to have good convergence and high precision, is employed for theoretical derivations. The influence of the gradient coefficients of FGM on the dispersion curves is illustrated. The numerical results also reveal differences between the properties of Lamb wave propagation in the FGM plate and the corresponding properties in a homogenous plate. In terms of results, we find that both the normal and anomalous dispersions exist in the first and the second modes of the Lamb wave that propagates in the FGM plate, while only the anomalous dispersion is in the first mode and only the normal dispersion is in the second mode for the homogenous plate. The wave structure is asymmetric due to the asymmetric properties of the material. The dominance of in-plane and out-plane displacements is different between the metal-rich and ceramic-rich surfaces. All these results give theoretical guidance not only for experimental measurement of material properties but also for nondestructive evaluation using an ultrasonic wave generation device. [ABSTRACT FROM AUTHOR]

Abstract: This paper reports simulations of the generation of Lamb wave modes in thin plates using a meander coil (meander line) EMAT, which works under the principle of Lorentz force mechanism in non-magnetic materials. The numerical simulations have been compared with measurements. The numerical work presented in this paper is divided into two parts. First, a 2D electromagnetic model is developed for calculating the Lorentz force density, which is the driving force for elastic wave generation within the plate. Second, the calculated force at each point in the metal is used as the driving force for generating elastic wave modes in the plate. These calculated Lamb wave modes are compared with those generated experimentally in a thin plate. Additionally, the measured wave modes are analyzed with the help of dispersion curves and a time–frequency analysis. Our numerical work is also extended to analyze the interaction of Lamb wave modes with defects. The simulations compare favorably with the measurements presented here. [Copyright &y& Elsevier]